Ben Hutchings [Sat, 25 Feb 2012 00:03:10 +0000 (00:03 +0000)]
sfc: Fix assignment of ip_summed for pre-allocated skbs
When pre-allocating skbs for received packets, we set ip_summed =
CHECKSUM_UNNCESSARY. We used to change it back to CHECKSUM_NONE when
the received packet had an incorrect checksum or unhandled protocol.
Commit bc8acf2c8c3e43fcc192762a9f964b3e9a17748b ('drivers/net: avoid
some skb->ip_summed initializations') mistakenly replaced the latter
assignment with a DEBUG-only assertion that ip_summed ==
CHECKSUM_NONE. This assertion is always false, but it seems no-one
has exercised this code path in a DEBUG build.
Fix this by moving our assignment of CHECKSUM_UNNECESSARY into
efx_rx_packet_gro().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Ben McKeegan [Fri, 24 Feb 2012 06:33:56 +0000 (06:33 +0000)]
ppp: fix 'ppp_mp_reconstruct bad seq' errors
This patch fixes a (mostly cosmetic) bug introduced by the patch
'ppp: Use SKB queue abstraction interfaces in fragment processing'
found here: http://www.spinics.net/lists/netdev/msg153312.html
The above patch rewrote and moved the code responsible for cleaning
up discarded fragments but the new code does not catch every case
where this is necessary. This results in some discarded fragments
remaining in the queue, and triggering a 'bad seq' error on the
subsequent call to ppp_mp_reconstruct. Fragments are discarded
whenever other fragments of the same frame have been lost.
This can generate a lot of unwanted and misleading log messages.
This patch also adds additional detail to the debug logging to
make it clearer which fragments were lost and which other fragments
were discarded as a result of losses. (Run pppd with 'kdebug 1'
option to enable debug logging.)
Signed-off-by: Ben McKeegan <ben@netservers.co.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Jozsef Kadlecsik [Fri, 24 Feb 2012 10:45:49 +0000 (11:45 +0100)]
netfilter: ctnetlink: fix soft lockup when netlink adds new entries (v2)
Marcell Zambo and Janos Farago noticed and reported that when
new conntrack entries are added via netlink and the conntrack table
gets full, soft lockup happens. This is because the nf_conntrack_lock
is held while nf_conntrack_alloc is called, which is in turn wants
to lock nf_conntrack_lock while evicting entries from the full table.
The patch fixes the soft lockup with limiting the holding of the
nf_conntrack_lock to the minimum, where it's absolutely required.
It required to extend (and thus change) nf_conntrack_hash_insert
so that it makes sure conntrack and ctnetlink do not add the same entry
twice to the conntrack table.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Said commit adds a check whether the carrier link is ok. If the link is
not ok, the skb is freed and no new dma descriptor added to the rx dma
channel. This causes trouble during initialization when the carrier
status has not yet been updated. If a lot of packets are received while
netif_carrier_ok returns false, all dma descriptors are freed and the
rx dma transfer is stopped.
The bug occurs when the board is connected to a network with lots of
traffic and the ifconfig down/up is done, e.g., when reconfiguring
the interface with DHCP.
The bug can be reproduced by flood pinging the davinci board while doing
ifconfig eth0 down
ifconfig eth0 up
on the board.
After that, the rx path stops working and the overrun value reported
by ifconfig is counting up.
This patch adds the PHY_HAS_INTERRUPT flag for IC+101 device series.
Also the patch does a simple dity-up to signal that
the driver actually is for IP101A LF and IP101G devices.
In fact, these are two similar PHYs that have the same IDs
and mainly differ for the EEE capability supported in the
G series.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David McKay [Tue, 21 Feb 2012 21:24:57 +0000 (21:24 +0000)]
netdev/phy/icplus: Correct broken phy_init code
The code for ip1001_config_init() was totally broken if you were not
using RGMII. Instead of returning an error code or zero it actually
returned the value in the IP1001_SPEC_CTRL_STATUS_2 register. It was
also trying to set the IP1001_APS_ON bit , but never actually wrote
back the register.
The error checking was also incorrect in both this function and the
reset function, so this patch fixes that up in a consistent fashion.
Signed-off-by: David McKay <david.mckay@st.com> Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Reported-by: Niccolò Belli <darkbasic@linuxsystems.it> Tested-by: Niccolò Belli <darkbasic@linuxsystems.it> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Scott Talbert [Tue, 21 Feb 2012 13:06:00 +0000 (13:06 +0000)]
Move Logitech Harmony 900 from cdc_ether to zaurus
In the current kernel implementation, the Logitech Harmony 900 remote
control is matched to the cdc_ether driver through the generic
USB_CDC_SUBCLASS_MDLM entry. However, this device appears to be of the
pseudo-MDLM (Belcarra) type, rather than the standard one. This patch
blacklists the Harmony 900 from the cdc_ether driver and whitelists it for
the pseudo-MDLM driver in zaurus.
Signed-off-by: Scott Talbert <talbert@techie.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Tue, 21 Feb 2012 21:30:25 +0000 (21:30 +0000)]
hso: memsetting wrong data in hso_get_count()
The intent was to clear out the icount struct here, but we accidentally
clear stack memory instead. It probably will lead to a NULL dereference
right away.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Guo-Fu Tseng [Wed, 22 Feb 2012 08:58:10 +0000 (08:58 +0000)]
jme: Fix FIFO flush issue
Set the RX FIFO flush watermark lower.
According to Federico and JMicron's reply,
setting it to 16QW would be stable on most platforms.
Otherwise, user might experience packet drop issue.
CC: stable@kernel.org Reported-by: Federico Quagliata <federico@quagliata.org> Fixed-by: Federico Quagliata <federico@quagliata.org> Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 21 Feb 2012 10:46:49 +0000 (10:46 +0000)]
atm: clip: remove clip_tbl
Commit 32092ecf0644 (atm: clip: Use device neigh support on top of
"arp_tbl".) introduced a bug since clip_tbl is zeroed : Crash occurs in
__neigh_for_each_release()
idle_timer_check() must use instead arp_tbl and neigh_check_cb() should
ignore non clip neighbours.
Idea from David Miller.
Reported-by: Meelis Roos <mroos@linux.ee> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Tested-by: Meelis Roos <mroos@linux.ee> Signed-off-by: David S. Miller <davem@davemloft.net>
Greg Rose [Tue, 21 Feb 2012 21:54:48 +0000 (16:54 -0500)]
rtnetlink: Fix problem with buffer allocation
Implement a new netlink attribute type IFLA_EXT_MASK. The mask
is a 32 bit value that can be used to indicate to the kernel that
certain extended ifinfo values are requested by the user application.
At this time the only mask value defined is RTEXT_FILTER_VF to
indicate that the user wants the ifinfo dump to send information
about the VFs belonging to the interface.
This patch fixes a bug in which certain applications do not have
large enough buffers to accommodate the extra information returned
by the kernel with large numbers of SR-IOV virtual functions.
Those applications will not send the new netlink attribute with
the interface info dump request netlink messages so they will
not get unexpectedly large request buffers returned by the kernel.
Modifies the rtnl_calcit function to traverse the list of net
devices and compute the minimum buffer size that can hold the
info dumps of all matching devices based upon the filter passed
in via the new netlink attribute filter mask. If no filter
mask is sent then the buffer allocation defaults to NLMSG_GOODSIZE.
With this change it is possible to add yet to be defined netlink
attributes to the dump request which should make it fairly extensible
in the future.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michel Machado [Tue, 21 Feb 2012 21:04:13 +0000 (16:04 -0500)]
neighbour: Fixed race condition at tbl->nht
When the fixed race condition happens:
1. While function neigh_periodic_work scans the neighbor hash table
pointed by field tbl->nht, it unlocks and locks tbl->lock between
buckets in order to call cond_resched.
2. Assume that function neigh_periodic_work calls cond_resched, that is,
the lock tbl->lock is available, and function neigh_hash_grow runs.
3. Once function neigh_hash_grow finishes, and RCU calls
neigh_hash_free_rcu, the original struct neigh_hash_table that function
neigh_periodic_work was using doesn't exist anymore.
4. Once back at neigh_periodic_work, whenever the old struct
neigh_hash_table is accessed, things can go badly.
Signed-off-by: Michel Machado <michel@digirati.com.br> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yevgeny Petrilin [Tue, 21 Feb 2012 03:41:07 +0000 (03:41 +0000)]
mlx4: Setting new port types after all interfaces unregistered
In port type change flow, need to set the new port types only after
all interfaces have finished the unregister process.
Otherwise, during unregister, one of the interfaces might issue a SET_PORT
command with wrong port types, it can cause bad FW behavior.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
Yevgeny Petrilin [Tue, 21 Feb 2012 03:39:32 +0000 (03:39 +0000)]
mlx4: Replacing pool_lock with mutex
Under the spinlock we call request_irq(), which allocates memory with GFP_KERNEL,
This causes the following trace when DEBUG_SPINLOCK is enabled, it can cause
the following trace:
Dave Jones [Mon, 20 Feb 2012 17:28:13 +0000 (17:28 +0000)]
zaurus: Add ID for C-750/C-760/C-860/SL-C3000 PDA in MDLM mode
In 16adf5d07987d93675945f3cecf0e33706566005 I removed an over-broad
alias that caused zaurus.ko to bind to unrelated devices.
I had a report that at least one valid case no longer auto-loads because of this.
This patch adds an ID for that case.
Reported-by: Raphael Wimmer <raphael.wimmer@ur.de> Signed-off-by: Dave Jones <davej@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jozsef Kadlecsik [Tue, 21 Feb 2012 13:53:57 +0000 (14:53 +0100)]
netfilter: ctnetlink: fix soft lockup when netlink adds new entries
Marcell Zambo and Janos Farago noticed and reported that when
new conntrack entries are added via netlink and the conntrack table
gets full, soft lockup happens. This is because the nf_conntrack_lock
is held while nf_conntrack_alloc is called, which is in turn wants
to lock nf_conntrack_lock while evicting entries from the full table.
The patch fixes the soft lockup with limiting the holding of the
nf_conntrack_lock to the minimum, where it's absolutely required.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Joerg Willmann [Tue, 21 Feb 2012 12:26:14 +0000 (13:26 +0100)]
netfilter: ebtables: fix alignment problem in ppc
ebt_among extension of ebtables uses __alignof__(_xt_align) while the
corresponding kernel module uses __alignof__(ebt_replace) to determine
the alignment in EBT_ALIGN().
These are the results of these values on different platforms:
ebtables fails to add rules which use the among extension.
I'm using kernel 2.6.33 and ebtables 2.0.10-4
According to Bart De Schuymer, userspace alignment was changed to
_xt_align to fix an alignment issue on a userspace32-kernel64 system
(he thinks it was for an ARM device). So userspace must be right.
The kernel alignment macro needs to change so it also uses _xt_align
instead of ebt_replace. The userspace changes date back from
June 29, 2009.
Signed-off-by: Joerg Willmann <joe@clnt.de>
Signed-off by: Bart De Schuymer <bdschuym@pandora.be> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Jack Morgenstein [Sun, 19 Feb 2012 21:38:52 +0000 (21:38 +0000)]
mlx4_core: Do not map BF area if capability is 0
BF can be disabled in some cases, the capability field, bf_reg_size is set
to zero in this case. Don't map the BF area in this case, it would cause
failures. In addition, leaving the BF area unmapped
also alerts the ETH driver to not use BF.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
Oliver Hartkopp [Wed, 15 Feb 2012 16:51:56 +0000 (17:51 +0100)]
can: sja1000: fix isr hang when hw is unplugged under load
In the case of hotplug enabled devices (PCMCIA/PCIeC) the removal of the
hardware can cause an infinite loop in the common sja1000 isr.
Use the already retrieved status register to indicate a possible hardware
removal and double check by reading the mode register in sja1000_is_absent.
Cc: stable@kernel.org [3.2+] Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Nikola Pajkovsky [Sun, 19 Feb 2012 10:47:43 +0000 (10:47 +0000)]
b44: remove __exit from b44_pci_exit()
WARNING: drivers/net/ethernet/broadcom/built-in.o(.init.text+0x5d): Section mismatch in reference from the function b44_init() to the function .exit.text:b44_pci_exit()
module exits with b44_cleanup()
Signed-off-by: Nikola Pajkovsky <n.pajkovsky@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julia Lawall [Sun, 19 Feb 2012 09:43:32 +0000 (09:43 +0000)]
drivers/atm/solos-pci.c: exchange pci_iounmaps
The calls to pci_iounmap are in the wrong order, as compared to the
associated calls to pci_iomap.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e,x;
statement S,S1;
int ret;
@@
e = pci_iomap(x,...)
... when != pci_iounmap(x,e)
if (<+...e...+>) S
... when any
when != pci_iounmap(x,e)
*if (...)
{ ... when != pci_iounmap(x,e)
return ...; }
... when any
pci_iounmap(x,e);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Thu, 16 Feb 2012 20:44:33 +0000 (20:44 +0000)]
net/ethernet: ks8851_mll: signedness bug in ks8851_probe()
netdev->irq is unsigned, so it's never less than zero.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Tested-by: Jan Weitzel <j.weitzel@phytec.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Horman [Thu, 16 Feb 2012 01:48:56 +0000 (01:48 +0000)]
vmxnet3: cap copy length at size of skb to prevent dropped frames on tx
I was recently shown that vmxnet3 devices on transmit, will drop very small udp
frames consistently. This is due to a regression introduced by commit 39d4a96fd7d2926e46151adbd18b810aeeea8ec0. This commit attempts to introduce an
optimization to the tx path, indicating that the underlying hardware behaves
optimally when at least 54 bytes of header data are available for direct access.
This causes problems however, if the entire frame is less than 54 bytes long.
The subsequent pskb_may_pull in vmxnet3_parse_and_copy_hdr fails, causing an
error return code, which leads to vmxnet3_tq_xmit dropping the frame.
Fix it by placing a cap on the copy length. For frames longer than 54 bytes, we
do the pull as we normally would. If the frame is shorter than that, copy the
whole frame, but no more. This ensures that we still get the optimization for
qualifying frames, but don't do any damange for frames that are too short.
Also, since I'm unable to do this, it wuold be great if vmware could follow up
this patch with some additional code commentary as to why 54 bytes is an optimal
pull length for a virtual NIC driver. The comment that introduced this was
vague on that. Thanks!
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Reported-by: Max Matveev <mmatveev@redhat.com> CC: Max Matveev <mmatveev@redhat.com> CC: "David S. Miller" <davem@davemloft.net> CC: Shreyas Bhatewara <sbhatewara@vmware.com> CC: "VMware, Inc." <pv-drivers@vmware.com> Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 15 Feb 2012 20:43:11 +0000 (20:43 +0000)]
atl1c: dont use highprio tx queue
This driver attempts to use two TX rings but lacks proper support :
1) IRQ handler only takes care of TX completion on first TX ring
2) the stop/start logic uses the legacy functions (for non multiqueue
drivers)
This means all packets witk skb mark set to 1 are sent through high
queue but are never cleaned and queue eventualy fills and block the
device, triggering the infamous "NETDEV WATCHDOG" message.
Lets use a single TX ring to fix the problem, this driver is not a real
multiqueue one yet.
Minimal fix for stable kernels.
Reported-by: Thomas Meyer <thomas@m3y3r.de> Tested-by: Thomas Meyer <thomas@m3y3r.de> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Cc: Jay Cliburn <jcliburn@gmail.com> Cc: Chris Snook <chris.snook@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 18 Feb 2012 23:40:00 +0000 (15:40 -0800)]
Merge tag 'fixes-3.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
These are the bug fixes that have accumulated since 3.3-rc3 in arm-soc.
The majority of them are regression fixes for stuff that broke during
the merge 3.3 window.
The notable ones are:
* The at91 ata drivers both broke because of an earlier cleanup patch that
some other patches were based on. Jean-Christophe decided to remove
the legacy at91_ide driver and fix the new-style at91-pata driver while
keeping the cleanup patch. I almost rejected the patches for being too
late and too big but in the end decided to accept them because they
fix a regression.
* A patch fixing build breakage from the sysdev-to-device conversion
colliding with other changes touches a number of mach-s3c files.
* b0654037 "ARM: orion: Fix Orion5x GPIO regression from MPP cleanup"
is a mechanical change that unfortunately touches a lot of lines
that should up in the diffstat.
* tag 'fixes-3.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
ARM: at91: drop ide driver in favor of the pata one
pata/at91: use newly introduced SMC accessors
ARM: at91: add accessor to manage SMC
ARM: at91:rtc/rtc-at91sam9: ioremap register bank
ARM: at91: USB AT91 gadget registration for module
ep93xx: fix build of vision_ep93xx.c
ARM: OMAP2xxx: PM: fix OMAP2xxx-specific UART idle bug in v3.3
ARM: orion: Fix USB phy for orion5x.
ARM: orion: Fix Orion5x GPIO regression from MPP cleanup
ARM: EXYNOS: Add cpu-offset property in gic device tree node
ARM: EXYNOS: Bring exynos4-dt up to date
ARM: OMAP3: cm-t35: fix section mismatch warning
ARM: OMAP2: Fix the OMAP2 only build break seen with 2011+ ARM tool-chains
ARM: tegra: paz00: fix wrong UART port on mini-pcie plug
ARM: tegra: paz00: fix wrong SD1 power gpio
i2c: tegra: Add devexit_p() for remove
ARM: EXYNOS: Correct M-5MOLS sensor clock frequency on Universal C210 board
ARM: EXYNOS: Correct framebuffer window size on Nuri board
ARM: SAMSUNG: Fix missing api-change from subsys_interface change
ARM: EXYNOS: Fix "warning: initialization from incompatible pointer type"
...
1) VETH_INFO_PEER netlink attribute needs to have it's size validated,
from Thomas Graf.
2) 'poll' module option of bnx2x driver crashes the machine, just remove
it. From Michal Schmidt.
3) ks8851_mll driver reads the irq number from two places, but only
initializes one of them, oops. Use only one location and fix this
problem, from Jan Weitzel.
4) Fix buffer overrun and unicast sterring bugs in mellanox mlx4 driver,
from Eugenia Emantayev.
5) Swapped kcalloc() args in RxRPC and mlx4, from Axel Lin.
6) PHY MDIO device name regression fixes from Florian Fainelli.
7) If the wake event IRQ line is different from the netdevice one, we
have to properly route it to the stmmac interrupt handler. From
Francesco Virlinzi.
8) Fix rwlock lock initialization ordering bug in mac80211, from
Mohammed Shafi Shajakhan.
9) TCP lost_cnt can get out of sync, and in fact go negative, in certain
circumstances. Fix the way we specify what sequence range to operate
on in tcp_sacktag_one() to fix this bug. From Neal Cardwell.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (27 commits)
net/ethernet: ks8851_mll fix irq handling
veth: Enforce minimum size of VETH_INFO_PEER
stmmac: update the driver version to Feb 2012 (v2)
stmmac: move hw init in the probe (v2)
stmmac: request_irq when use an ext wake irq line (v2)
stmmac: do not discard frame on dribbling bit assert
ipheth: Add iPhone 4S
mlx4: add unicast steering entries to resource_tracker
mlx4: fix QP tree trashing
mlx4: fix buffer overrun
3c59x: shorten timer period for slave devices
netpoll: netpoll_poll_dev() should access dev->flags
RxRPC: Fix kcalloc parameters swapped
bnx2x: remove the 'poll' module option
tcp: fix tcp_shifted_skb() adjustment of lost_cnt_hint for FACK
ks8851: Fix NOHZ local_softirq_pending 08 warning
bnx2x: fix bnx2x_storm_stats_update() on big endian
ixp4xx-eth: fix PHY name to match MDIO bus name
octeon: fix PHY name to match MDIO bus name
fec: fix PHY name to match fixed MDIO bus name
...
Linus Torvalds [Sat, 18 Feb 2012 23:37:25 +0000 (15:37 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Fixes a bootstrapping issue for some registers when a less commonly used
method for register cache initialisation is used. Only affects a fairly
small proportion of users that both don't use explicit register defaults
and do use the cache.
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: Fix cache defaults initialization from raw cache defaults
Linus Torvalds [Sat, 18 Feb 2012 23:28:56 +0000 (15:28 -0800)]
Merge tag 'ecryptfs-3.3-rc4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs
Fixes maximum filename length and filesystem type reporting in statfs() calls
and also fixes stale inode mode bits on eCryptfs inodes after a POSIX ACL was
set on the lower filesystem's inode.
* tag 'ecryptfs-3.3-rc4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
ecryptfs: remove the second argument of k[un]map_atomic()
eCryptfs: Copy up lower inode attrs after setting lower xattr
eCryptfs: Improve statfs reporting
Linus Torvalds [Sat, 18 Feb 2012 23:26:37 +0000 (15:26 -0800)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Here are a few more fixes for powerpc. Some are regressions, the rest
is simple/obvious/nasty enough that I deemed it good to go now.
Here's also step one of deprecating legacy iSeries support: we are
removing it from the main defconfig.
Nobody seems to be using it anymore and the code is nasty to maintain,
(involves horrible hacks in various low level areas of the kernel) so we
plan to actually rip it out at some point. For now let's just avoid
building it by default. Stephen will proceed to do the actual removal
later (probably 3.4 or 3.5).
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/perf: power_pmu_start restores incorrect values, breaking frequency events
powerpc/adb: Use set_current_state()
powerpc: Disable interrupts early in Program Check
powerpc: Remove legacy iSeries from ppc64_defconfig
powerpc/fsl/pci: Fix PCIe fixup regression
powerpc: Fix kernel log of oops/panic instruction dump
Linus Torvalds [Sat, 18 Feb 2012 23:26:11 +0000 (15:26 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci
One regression fix for SR-IOV on PPC and a couple of misc fixes from
Yinghai.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci:
PCI: Fix pci cardbus removal
PCI: set pci sriov page size before reading SRIOV BAR
PCI: workaround hard-wired bus number V2
Linus Torvalds [Sat, 18 Feb 2012 23:25:39 +0000 (15:25 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
3 radeon fixes, I have some exynos fixes to push later but I'll queue
them separately once I've looked them over a bit.
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/kms: fix MSI re-arm on rv370+
drm/radeon/kms/atom: bios scratch reg handling updates
drm/radeon/kms: drop lock in return path of radeon_fence_count_emitted.
Linus Torvalds [Sat, 18 Feb 2012 20:56:35 +0000 (12:56 -0800)]
i387: re-introduce FPU state preloading at context switch time
After all the FPU state cleanups and finally finding the problem that
caused all our FPU save/restore problems, this re-introduces the
preloading of FPU state that was removed in commit b3b0870ef3ff ("i387:
do not preload FPU state at task switch time").
However, instead of simply reverting the removal, this reimplements
preloading with several fixes, most notably
- properly abstracted as a true FPU state switch, rather than as
open-coded save and restore with various hacks.
In particular, implementing it as a proper FPU state switch allows us
to optimize the CR0.TS flag accesses: there is no reason to set the
TS bit only to then almost immediately clear it again. CR0 accesses
are quite slow and expensive, don't flip the bit back and forth for
no good reason.
- Make sure that the same model works for both x86-32 and x86-64, so
that there are no gratuitous differences between the two due to the
way they save and restore segment state differently due to
architectural differences that really don't matter to the FPU state.
- Avoid exposing the "preload" state to the context switch routines,
and in particular allow the concept of lazy state restore: if nothing
else has used the FPU in the meantime, and the process is still on
the same CPU, we can avoid restoring state from memory entirely, just
re-expose the state that is still in the FPU unit.
That optimized lazy restore isn't actually implemented here, but the
infrastructure is set up for it. Of course, older CPU's that use
'fnsave' to save the state cannot take advantage of this, since the
state saving also trashes the state.
In other words, there is now an actual _design_ to the FPU state saving,
rather than just random historical baggage. Hopefully it's easier to
follow as a result.
Linus Torvalds [Sat, 18 Feb 2012 05:48:54 +0000 (21:48 -0800)]
i387: move TS_USEDFPU flag from thread_info to task_struct
This moves the bit that indicates whether a thread has ownership of the
FPU from the TS_USEDFPU bit in thread_info->status to a word of its own
(called 'has_fpu') in task_struct->thread.has_fpu.
This fixes two independent bugs at the same time:
- changing 'thread_info->status' from the scheduler causes nasty
problems for the other users of that variable, since it is defined to
be thread-synchronous (that's what the "TS_" part of the naming was
supposed to indicate).
So perfectly valid code could (and did) do
ti->status |= TS_RESTORE_SIGMASK;
and the compiler was free to do that as separate load, or and store
instructions. Which can cause problems with preemption, since a task
switch could happen in between, and change the TS_USEDFPU bit. The
change to TS_USEDFPU would be overwritten by the final store.
In practice, this seldom happened, though, because the 'status' field
was seldom used more than once, so gcc would generally tend to
generate code that used a read-modify-write instruction and thus
happened to avoid this problem - RMW instructions are naturally low
fat and preemption-safe.
- On x86-32, the current_thread_info() pointer would, during interrupts
and softirqs, point to a *copy* of the real thread_info, because
x86-32 uses %esp to calculate the thread_info address, and thus the
separate irq (and softirq) stacks would cause these kinds of odd
thread_info copy aliases.
This is normally not a problem, since interrupts aren't supposed to
look at thread information anyway (what thread is running at
interrupt time really isn't very well-defined), but it confused the
heck out of irq_fpu_usable() and the code that tried to squirrel
away the FPU state.
(It also caused untold confusion for us poor kernel developers).
It also turns out that using 'task_struct' is actually much more natural
for most of the call sites that care about the FPU state, since they
tend to work with the task struct for other reasons anyway (ie
scheduling). And the FPU data that we are going to save/restore is
found there too.
Thanks to Arjan Van De Ven <arjan@linux.intel.com> for pointing us to
the %esp issue.
Cc: Arjan van de Ven <arjan@linux.intel.com> Reported-and-tested-by: Raphael Prevost <raphael@buro.asia> Acked-and-tested-by: Suresh Siddha <suresh.b.siddha@intel.com> Tested-by: Peter Anvin <hpa@zytor.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 17 Feb 2012 03:11:15 +0000 (19:11 -0800)]
i387: move AMD K7/K8 fpu fxsave/fxrstor workaround from save to restore
The AMD K7/K8 CPUs don't save/restore FDP/FIP/FOP unless an exception is
pending. In order to not leak FIP state from one process to another, we
need to do a floating point load after the fxsave of the old process,
and before the fxrstor of the new FPU state. That resets the state to
the (uninteresting) kernel load, rather than some potentially sensitive
user information.
We used to do this directly after the FPU state save, but that is
actually very inconvenient, since it
(a) corrupts what is potentially perfectly good FPU state that we might
want to lazy avoid restoring later and
(b) on x86-64 it resulted in a very annoying ordering constraint, where
"__unlazy_fpu()" in the task switch needs to be delayed until after
the DS segment has been reloaded just to get the new DS value.
Coupling it to the fxrstor instead of the fxsave automatically avoids
both of these issues, and also ensures that we only do it when actually
necessary (the FP state after a save may never actually get used). It's
simply a much more natural place for the leaked state cleanup.
Linus Torvalds [Thu, 16 Feb 2012 23:45:23 +0000 (15:45 -0800)]
i387: do not preload FPU state at task switch time
Yes, taking the trap to re-load the FPU/MMX state is expensive, but so
is spending several days looking for a bug in the state save/restore
code. And the preload code has some rather subtle interactions with
both paravirtualization support and segment state restore, so it's not
nearly as simple as it should be.
Also, now that we no longer necessarily depend on a single bit (ie
TS_USEDFPU) for keeping track of the state of the FPU, we migth be able
to do better. If we are really switching between two processes that
keep touching the FP state, save/restore is inevitable, but in the case
of having one process that does most of the FPU usage, we may actually
be able to do much better than the preloading.
In particular, we may be able to keep track of which CPU the process ran
on last, and also per CPU keep track of which process' FP state that CPU
has. For modern CPU's that don't destroy the FPU contents on save time,
that would allow us to do a lazy restore by just re-enabling the
existing FPU state - with no restore cost at all!
Tyler Hicks [Tue, 7 Feb 2012 23:55:40 +0000 (17:55 -0600)]
eCryptfs: Copy up lower inode attrs after setting lower xattr
After passing through a ->setxattr() call, eCryptfs needs to copy the
inode attributes from the lower inode to the eCryptfs inode, as they
may have changed in the lower filesystem's ->setxattr() path.
One example is if an extended attribute containing a POSIX Access
Control List is being set. The new ACL may cause the lower filesystem to
modify the mode of the lower inode and the eCryptfs inode would need to
be updated to reflect the new mode.
Tyler Hicks [Sat, 5 Nov 2011 17:45:08 +0000 (13:45 -0400)]
eCryptfs: Improve statfs reporting
statfs() calls on eCryptfs files returned the wrong filesystem type and,
when using filename encryption, the wrong maximum filename length.
If mount-wide filename encryption is enabled, the cipher block size and
the lower filesystem's max filename length will determine the max
eCryptfs filename length. Pre-tested, known good lengths are used when
the lower filesystem's namelen is 255 and a cipher with 8 or 16 byte
block sizes is used. In other, less common cases, we fall back to a safe
rounded-down estimate when determining the eCryptfs namelen.
Linus Torvalds [Thu, 16 Feb 2012 21:33:12 +0000 (13:33 -0800)]
i387: don't ever touch TS_USEDFPU directly, use helper functions
This creates three helper functions that do the TS_USEDFPU accesses, and
makes everybody that used to do it by hand use those helpers instead.
In addition, there's a couple of helper functions for the "change both
CR0.TS and TS_USEDFPU at the same time" case, and the places that do
that together have been changed to use those. That means that we have
fewer random places that open-code this situation.
The intent is partly to clarify the code without actually changing any
semantics yet (since we clearly still have some hard to reproduce bug in
this area), but also to make it much easier to use another approach
entirely to caching the CR0.TS bit for software accesses.
Right now we use a bit in the thread-info 'status' variable (this patch
does not change that), but we might want to make it a full field of its
own or even make it a per-cpu variable.
Linus Torvalds [Thu, 16 Feb 2012 20:22:48 +0000 (12:22 -0800)]
i387: move TS_USEDFPU clearing out of __save_init_fpu and into callers
Touching TS_USEDFPU without touching CR0.TS is confusing, so don't do
it. By moving it into the callers, we always do the TS_USEDFPU next to
the CR0.TS accesses in the source code, and it's much easier to see how
the two go hand in hand.
Linus Torvalds [Thu, 16 Feb 2012 17:15:04 +0000 (09:15 -0800)]
i387: fix x86-64 preemption-unsafe user stack save/restore
Commit 5b1cbac37798 ("i387: make irq_fpu_usable() tests more robust")
added a sanity check to the #NM handler to verify that we never cause
the "Device Not Available" exception in kernel mode.
However, that check actually pinpointed a (fundamental) race where we do
cause that exception as part of the signal stack FPU state save/restore
code.
Because we use the floating point instructions themselves to save and
restore state directly from user mode, we cannot do that atomically with
testing the TS_USEDFPU bit: the user mode access itself may cause a page
fault, which causes a task switch, which saves and restores the FP/MMX
state from the kernel buffers.
This kind of "recursive" FP state save is fine per se, but it means that
when the signal stack save/restore gets restarted, it will now take the
'#NM' exception we originally tried to avoid. With preemption this can
happen even without the page fault - but because of the user access, we
cannot just disable preemption around the save/restore instruction.
There are various ways to solve this, including using the
"enable/disable_page_fault()" helpers to not allow page faults at all
during the sequence, and fall back to copying things by hand without the
use of the native FP state save/restore instructions.
However, the simplest thing to do is to just allow the #NM from kernel
space, but fix the race in setting and clearing CR0.TS that this all
exposed: the TS bit changes and the TS_USEDFPU bit absolutely have to be
atomic wrt scheduling, so while the actual state save/restore can be
interrupted and restarted, the act of actually clearing/setting CR0.TS
and the TS_USEDFPU bit together must not.
Instead of just adding random "preempt_disable/enable()" calls to what
is already excessively ugly code, this introduces some helper functions
that mostly mirror the "kernel_fpu_begin/end()" functionality, just for
the user state instead.
Those helper functions should probably eventually replace the other
ad-hoc CR0.TS and TS_USEDFPU tests too, but I'll need to think about it
some more: the task switching functionality in particular needs to
expose the difference between the 'prev' and 'next' threads, while the
new helper functions intentionally were written to only work with
'current'.
Anton Blanchard [Wed, 15 Feb 2012 18:48:22 +0000 (18:48 +0000)]
powerpc/perf: power_pmu_start restores incorrect values, breaking frequency events
perf on POWER stopped working after commit e050e3f0a71b (perf: Fix
broken interrupt rate throttling). That patch exposed a bug in
the POWER perf_events code.
Since the PMCs count upwards and take an exception when the top bit
is set, we want to write 0x80000000 - left in power_pmu_start. We were
instead programming in left which effectively disables the counter
until we eventually hit 0x80000000. This could take seconds or longer.
With the patch applied I get the expected number of samples:
SAMPLE events: 9948
Signed-off-by: Anton Blanchard <anton@samba.org> Acked-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: <stable@kernel.org>
powerpc: Disable interrupts early in Program Check
Program Check exceptions are the result of WARNs, BUGs, some
type of breakpoints, kprobe, and other illegal instructions.
We want interrupts (and thus preemption) to remain disabled
while doing the initial stage of testing the reason and
branching off to a debugger or kprobe, so we are still on
the original CPU which makes debugging easier in various cases.
This is how the code was intended, hence the local_irq_enable()
right in the middle of program_check_exception().
However, the assembly exception prologue for that exception was
incorrectly marked as enabling interrupts, which defeats that
(and records a redundant enable with lockdep).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Upstream changes to the way PHB resources are registered
broke the resource fixup for FSL boards.
We can no longer rely on the resource pointer array for the PHB's
pci_bus structure, so let's leave it alone and go straight for
the PHB resources instead. This also makes the code generally
more readable.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Ira Snyder [Fri, 6 Jan 2012 12:34:07 +0000 (12:34 +0000)]
powerpc: Fix kernel log of oops/panic instruction dump
A kernel oops/panic prints an instruction dump showing several
instructions before and after the instruction which caused the
oops/panic.
The code intended that the faulting instruction be enclosed in angle
brackets, however a bug caused the faulting instruction to be
interpreted by printk() as the message log level.
To fix this, the KERN_CONT log level is added before the actual text of
the printed message.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu> Cc: Paul Mackerras <paulus@samba.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: linuxppc-dev@lists.ozlabs.org Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Alexey Dobriyan [Sat, 14 Jan 2012 18:44:49 +0000 (21:44 +0300)]
crypto: sha512 - use standard ror64()
Use standard ror64() instead of hand-written.
There is no standard ror64, so create it.
The difference is shift value being "unsigned int" instead of uint64_t
(for which there is no reason). gcc starts to emit native ROR instructions
which it doesn't do for some reason currently. This should make the code
faster.
Patch survives in-tree crypto test and ping flood with hmac(sha512) on.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Thomas Graf [Wed, 15 Feb 2012 04:09:46 +0000 (04:09 +0000)]
veth: Enforce minimum size of VETH_INFO_PEER
VETH_INFO_PEER carries struct ifinfomsg plus optional IFLA
attributes. A minimal size of sizeof(struct ifinfomsg) must be
enforced or we may risk accessing that struct beyond the limits
of the netlink message.
Signed-off-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the MAC HW initialization and
the HW feature verification from the open to the probe
function as D. Miller suggested.
So the patch actually reorganizes and tidies-up some parts of
the driver and indeed fixes some problem when tune its HW features.
These can be overwritten by looking at the HW cap register at
run-time and that generated problems.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Reviewed-by: Francesco Virlinzi <francesco.virlinzi@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac: request_irq when use an ext wake irq line (v2)
In case of we use an external Wake-Up IRQ line
(priv->wol_irq != dev->irq) we need to invoke the
request_irq.
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com> Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tim Gardner [Wed, 15 Feb 2012 07:50:15 +0000 (07:50 +0000)]
ipheth: Add iPhone 4S
BugLink: http://bugs.launchpad.net/bugs/900802 Cc: stable@vger.kernel.org 3.2+ Signed-off-by: Till Kamppeter <till.kamppeter@gmail.com> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4: add unicast steering entries to resource_tracker
Add unicast steering entries to resource tracker.
Do qp_detach also for these entries when VF doesn't shut down gracefully.
Otherwise there is leakage of these resources, since they are not tracked.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il> Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
When adding new unicast steer entry, before moving qp to state ready,
actually before calling mlx4_RST2INIT_QP_wrapper(), there were added
a lot of entries with local_qpn=0 into radix tree.
This fact impacted the get_res() function and proper functioning
of resource tracker in addition to adding trash entries into radix tree.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il> Reviewed-by: Yevgeny Petrilin <yevgenyp@melllanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
When passing MLX4_UC_STEER=1 it was translated to value 2
after mlx4_QP_ATTACH_wrapper. Therefore in new_steering_entry()
unicast steer entries were added to index 2 of array of size 2.
Fixing this bug by shift right to one position.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il> Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Roskin [Sat, 11 Feb 2012 15:01:53 +0000 (10:01 -0500)]
ath9k: stop on rates with idx -1 in ath9k rate control's .tx_status
Rate control algorithms are supposed to stop processing when they
encounter a rate with the index -1. Checking for rate->count not being
zero is not enough.
Allowing a rate with negative index leads to memory corruption in
ath_debug_stat_rc().
One consequence of the bug is discussed at
https://bugzilla.redhat.com/show_bug.cgi?id=768639
Signed-off-by: Pavel Roskin <proski@gnu.org> Cc: stable@vger.kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar [Fri, 10 Feb 2012 02:32:22 +0000 (18:32 -0800)]
mwifiex: clear previous security setting during association
Driver maintains different flags for WEP, WPA, WPA2 security modes.
Appropriate flag is set using security information provided in
connect request. mwifiex_is_network_compatible() routine uses them
to check if driver's setting is compatible with AP. Association is
aborted if the routine fails.
For some corner cases, it is observed that association is failed
even for valid security information based on association history.
This patch fixes the problem by clearing previous security setting
during each association.
We should set WEP key provided in connect request as default tx key.
This missing change is also added here.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Wed, 8 Feb 2012 18:17:11 +0000 (19:17 +0100)]
mac80211: do not call rate control .tx_status before .rate_init
Most rate control implementations assume .get_rate and .tx_status are only
called once the per-station data has been fully initialized.
minstrel_ht crashes if this assumption is violated.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Tested-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 20 Jan 2012 12:55:23 +0000 (13:55 +0100)]
mac80211: call rate control only after init
There are situations where we don't have the
necessary rate control information yet for
station entries, e.g. when associating. This
currently doesn't really happen due to the
dummy station handling; explicitly disabling
rate control when it's not initialised will
allow us to remove dummy stations.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
regmap: Fix cache defaults initialization from raw cache defaults
Currently registers with a value of 0 are ignored when initializing the register
defaults from raw defaults. This worked in the past, because registers without a
explicit default were assumed to have a default value of 0. This was changed in
commit b03622a8 ("regmap: Ensure rbtree syncs registers set to zero properly").
As a result registers, which have a raw default value of 0 are now assumed to
have no default. This again can result in unnecessary writes when syncing the
cache. It will also result in unnecessary reads for e.g. the first update
operation. In the case where readback is not possible this will even let the
update operation fail, if the register has not been written to before.
So this patch removes the check. Instead it adds a check to ignore raw defaults
for registers which are volatile, since those registers are not cached.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: stable@vger.kernel.org
Linus Torvalds [Wed, 15 Feb 2012 16:05:18 +0000 (08:05 -0800)]
i387: fix sense of sanity check
The check for save_init_fpu() (introduced in commit 5b1cbac37798: "i387:
make irq_fpu_usable() tests more robust") was the wrong way around, but
I hadn't noticed, because my "tests" were bogus: the FPU exceptions are
disabled by default, so even doing a divide by zero never actually
triggers this code at all unless you do extra work to enable them.
So if anybody did enable them, they'd get one spurious warning.
Ulisses Furquim [Mon, 30 Jan 2012 20:26:29 +0000 (18:26 -0200)]
Bluetooth: Fix possible use after free in delete path
We need to use the _sync() version for cancelling the info and security
timer in the L2CAP connection delete path. Otherwise the delayed work
handler might run after the connection object is freed.
Ulisses Furquim [Mon, 30 Jan 2012 20:26:28 +0000 (18:26 -0200)]
Bluetooth: Remove usage of __cancel_delayed_work()
__cancel_delayed_work() is being used in some paths where we cannot
sleep waiting for the delayed work to finish. However, that function
might return while the timer is running and the work will be queued
again. Replace the calls with safer cancel_delayed_work() version
which spins until the timer handler finishes on other CPUs and
cancels the delayed work.
Johan Hedberg [Fri, 3 Feb 2012 19:29:40 +0000 (21:29 +0200)]
Bluetooth: Add missing QUIRK_NO_RESET test to hci_dev_do_close
We should only perform a reset in hci_dev_do_close if the
HCI_QUIRK_NO_RESET flag is set (since in such a case a reset will not be
performed when initializing the device).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org>
The issue appears to be the rfcomm_session_put in rfcomm_recv_ua. This
operation doesn't seem be to required as for the non-initiator case we
have the rfcomm_process_rx doing an explicit put and in the initiator
case the last dlc_unlink will drive the reference counter to 0.
There have been several attempts to fix these issue:
6c2718d Bluetooth: Do not call rfcomm_session_put() for RFCOMM UA on closed socket 683d949 Bluetooth: Never deallocate a session when some DLC points to it
but AFAICS they do not fix the issue just make it harder to reproduce.
Andre Guedes [Fri, 27 Jan 2012 22:42:02 +0000 (19:42 -0300)]
Bluetooth: Fix potential deadlock
We don't need to use the _sync variant in hci_conn_hold and
hci_conn_put to cancel conn->disc_work delayed work. This way
we avoid potential deadlocks like this one reported by lockdep.
======================================================
[ INFO: possible circular locking dependency detected ]
3.2.0+ #1 Not tainted
-------------------------------------------------------
kworker/u:1/17 is trying to acquire lock:
(&hdev->lock){+.+.+.}, at: [<ffffffffa0041155>] hci_conn_timeout+0x62/0x158 [bluetooth]
but task is already holding lock:
((&(&conn->disc_work)->work)){+.+...}, at: [<ffffffff81035751>] process_one_work+0x11a/0x2bf
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
Octavian Purdila [Sat, 21 Jan 2012 22:28:34 +0000 (00:28 +0200)]
Bluetooth: silence lockdep warning
Since bluetooth uses multiple protocols types, to avoid lockdep
warnings, we need to use different lockdep classes (one for each
protocol type).
This is already done in bt_sock_create but it misses a couple of cases
when new connections are created. This patch corrects that to fix the
following warning:
Bluetooth: l2cap_set_timer needs jiffies as timeout value
After moving L2CAP timers to workqueues l2cap_set_timer expects timeout
value to be specified in jiffies but constants defined in miliseconds
are used. This makes timeouts unreliable when CONFIG_HZ is not set to
1000.
__set_chan_timer macro still uses jiffies as input to avoid multiple
conversions from/to jiffies for sk_sndtimeo value which is already
specified in jiffies.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com> Ackec-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Bluetooth: Fix sk_sndtimeo initialization for L2CAP socket
sk_sndtime value should be specified in jiffies thus initial value
needs to be converted from miliseconds. Otherwise this timeout is
unreliable when CONFIG_HZ is not set to 1000.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de> Acked-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Peter Hurley [Fri, 13 Jan 2012 14:11:30 +0000 (15:11 +0100)]
Bluetooth: Fix l2cap conn failures for ssp devices
Commit 330605423c fixed l2cap conn establishment for non-ssp remote
devices by not setting HCI_CONN_ENCRYPT_PEND every time conn security
is tested (which was always returning failure on any subsequent
security checks).
However, this broke l2cap conn establishment for ssp remote devices
when an ACL link was already established at SDP-level security. This
fix ensures that encryption must be pending whenever authentication
is also pending.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Tested-by: Daniel Wagner <daniel.wagner@bmw-carit.de> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Linus Torvalds [Tue, 14 Feb 2012 23:26:42 +0000 (15:26 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
One small bug fix from Axel plus a fix for a build failure in unrealistic
but commonly built configs which for some reason manage to survive for
an awfully long time in -next without any reports.
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: Fix getting voltage in max8649_enable_time()
regulator: Fix mc13xxx regulator modular build (again)
Linus Torvalds [Tue, 14 Feb 2012 23:21:25 +0000 (15:21 -0800)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Quoth BenH:
"Here are a few powerpc fixes for 3.3, all pretty trivial. I also
added the patch to define GET_IP/SET_IP so we can use some more
asm-generic goodness."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/pseries/eeh: Fix crash when error happens during device probe
powerpc/pseries: Fix partition migration hang in stop_topology_update
powerpc/powernv: Disable interrupts while taking phb->lock
powerpc: Fix WARN_ON in decrementer_check_overflow
powerpc/wsp: Fix IRQ affinity setting
powerpc: Implement GET_IP/SET_IP
powerpc/wsp: Permanently enable PCI class code workaround
Linus Torvalds [Tue, 14 Feb 2012 23:20:50 +0000 (15:20 -0800)]
Merge tag 'mmc-fixes-for-3.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
MMC fixes for 3.3-rc4:
* The most visible fix here is against a regression introduced in 3.3-rc1
that ran cards in Ultra High Speed mode even when they failed to initialize
in that mode, leading to lower-speed cards failing to mount.
* A lockdep warning introduced in 3.3-rc1 is fixed.
* Various other small driver fixes, most notably for a NULL dereference
when using highmem with dw_mmc.
* tag 'mmc-fixes-for-3.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
mmc: dw_mmc: Fix PIO mode with support of highmem
mmc: atmel-mci: save and restore sdioirq when soft reset is performed
mmc: block: Init ro_lock sysfs attr to fix lockdep warnings
mmc: sh_mmcif: fix late delayed work initialisation
mmc: tmio_mmc: fix card eject during IO with DMA
mmc: core: Fix comparison issue in mmc_compare_ext_csds
mmc: core: Fix PowerOff Notify suspend/resume
mmc: sdhci-pci: set Medfield SDIO as non-removable
mmc: core: add the capability for broken voltage
mmc: core: Fix low speed mmc card detection failure
mmc: esdhc: set the timeout to the max value
mmc: esdhc: add PIO mode support
mmc: core: Ensure clocks are always enabled before host interaction
mmc: of_mmc_spi: fix little endian support
mmc: core: UHS sdio card that fails should not exceed 50MHz
mmc: esdhc: fix errors when booting kernel on Freescale eSDHC version 2.3
Linus Torvalds [Tue, 14 Feb 2012 23:20:11 +0000 (15:20 -0800)]
Merge tag 'stable/for-linus-fixes-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Two fixes for VCPU offlining; One to fix the string format exposed
by the xen-pci[front|back] to conform to the one used in majority of
PCI drivers; Two fixes to make the code more resilient to invalid
configurations.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
* tag 'stable/for-linus-fixes-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xenbus_dev: add missing error check to watch handling
xen/pci[front|back]: Use %d instead of %1x for displaying PCI devfn.
xen pvhvm: do not remap pirqs onto evtchns if !xen_have_vector_callback
xen/smp: Fix CPU online/offline bug triggering a BUG: scheduling while atomic.
xen/bootup: During bootup suppress XENBUS: Unable to read cpu state
projects / karo-tx-linux.git / log