Daniel Vetter [Fri, 1 Jun 2012 08:49:16 +0000 (10:49 +0200)]
Merge remote-tracking branch 'airlied/drm-prime-vmap' into drm-intel-next-queued
We need the latest dma-buf code from Dave Airlie so that we can pimp
the backing storage handling code in drm/i915 with Chris Wilson's
unbound tracking and stolen mem backed gem object code.
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Thu, 31 May 2012 12:57:43 +0000 (14:57 +0200)]
drm/i915: simplify sysfs setup code
Positively checking for the required feature/gen is simpler than build
a cascade of negative "we need to bail" checks. And the later won't
scale if we add more stuff that doesn't fit in nicely.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net> Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Thu, 31 May 2012 12:57:42 +0000 (14:57 +0200)]
drm/i915: initialize the parity work only once
This fixes an (albeit really hard to hit) race resulting in an oops:
- The parity work get scheduled.
- We re-init the irq state and call INIT_WORK again.
- The workqueue code tries to run the work item and stumbles over a
work item that should be on it's runlist.
Also initiliaze the work item unconditionally like all the others,
it's simpler.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net> Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben Widawsky [Fri, 25 May 2012 23:56:25 +0000 (16:56 -0700)]
drm/i915: l3 parity sysfs interface
Dumb binary interfaces which allow root-only updates of the cache
remapping registers. As mentioned in a previous patch, software using
this interface needs to know about HW limits, and other programming
considerations as the kernel interface does no checking for these things
on the root-only interface.
v1: Drop extra posting reads (Chris)
Return negative values in the sysfs interfaces on errors (Chris)
v2: Return -EINVAL for offset % 4 (Jesse)
Move schizo userspace check out (Jesse)
Cleaner sysfs item initializers (Daniel)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben Widawsky [Fri, 25 May 2012 23:56:23 +0000 (16:56 -0700)]
drm/i915: enable parity error interrupts
The previous patch put all the code, and handlers in place. It should
now be safe to enable the parity error interrupt. The parity error must
be unmasked in both the GTIMR, and the CS IMR. Unfortunately, the docs
aren't clear about this; nevertheless it's the truth.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben Widawsky [Fri, 25 May 2012 23:56:22 +0000 (16:56 -0700)]
drm/i915: Dynamic Parity Detection handling
On IVB hardware we are given an interrupt whenever a L3 parity error
occurs in the L3 cache. The L3 cache is used by internal GPU clients
only. This is a very rare occurrence (in fact to test this I need to
use specially instrumented silicon).
When a row in the L3 cache detects a parity error the HW generates an
interrupt. The interrupt is masked in GTIMR until we get a chance to
read some registers and alert userspace via a uevent. With this
information userspace can use a sysfs interface (follow-up patch) to
remap those rows.
Way above my level of understanding, but if a given row fails, it is
statistically more likely to fail again than a row which has not failed.
Therefore it is desirable for an operating system to maintain a lifelong
list of failing rows and always remap any bad rows on driver load.
Hardware limits the number of rows that are remappable per bank/subbank,
and should more than that many rows detect parity errors, software
should maintain a list of the most frequent errors, and remap those
rows.
V2: Drop WARN_ON(IS_GEN6) (Jesse)
DRM_DEBUG row/bank/subbank on errror (Jesse)
Comment updates (Jesse)
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Wed, 30 May 2012 12:52:26 +0000 (14:52 +0200)]
drm/i915: reuse the sdvo tv clock adjustment in ilk mode_set
Jesse extracted this nice helper in his i9xx_crtc_mode_set refactor,
but we have the identical code in ironlake_ccrtc_mode_set. And that
function is huge, so extracting some code full of magic numbers is
always nice.
Noticed while trying to get a handle on our dp clock code.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Mon, 28 May 2012 19:43:00 +0000 (16:43 -0300)]
drm/i915: add some barriers when changing DIPs
On IVB and older, we basically have two registers: the control and the
data register. We write a few consecutitve times to the control
register, and we need these writes to arrive exactly in the specified
order.
Also, when we're changing the data register, we need to guarantee that
anything written to the control register already arrived (since
changing the control register can change where the data register
points to). Also, we need to make sure all the writes to the data
register happen exactly in the specified order, and we also *can't*
read the data register during this process, since reading and/or
writing it will change the place it points to.
So invoke the "better safe than sorry" rule and just be careful and
put barriers everywhere :)
On HSW we still have a control register that we write many times, but
we have many data registers.
Demanded-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Mon, 28 May 2012 19:42:58 +0000 (16:42 -0300)]
drm/i915: remove comment about HSW HDMI DIPs
HSW support is now just like all the other generations: we send AVI
and SPD InfoFrames. There are other DIPs for HSW, but there are other
DIPs for the previous generations too. For each gen, we can see which
DIPs are missing by looking at the 'set_infoframes' function: we
explicitly disable the DIPs we're not using.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Mon, 28 May 2012 19:42:56 +0000 (16:42 -0300)]
drm/i915: don't set SDVO_BORDER_ENABLE when we're HDMI
The register that controls the HDMI port can be used to control the
sDVO port. Some bits are defined only for sDVO, and SDVO_BORDER_ENABLE
is one of those: HDMI ports that can't be used in sDVO mode don't even
have this bit defined in their specifications.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Mon, 28 May 2012 19:42:55 +0000 (16:42 -0300)]
drm/i915: don't write 0 to DIP control at HDMI init
At this time, the HDMI port is enabled, and the DIP control register
specification says we need to disable the port *before* disabling the
DIPs. Also, while doing this we risk telling the HW to send the AVI
DIPs once (not every VSync), which really seems to confuse the HW and
trigger bugs where the DIPs are not sent.
This code was here just to set the DIP register to a 'known state'
before using it, but since now the set_infoframes functions already
set the control registers to a known state, this code can go away.
Also, the previous code disables *all* the DIP registers for *each*
HDMI port, so we end disabling each DIP register more than once.
This patch solves a problem I can reproduce on my IVB machine. When I
boot it with just a single HDMI monitor, the AVI InfoFrames are not
sent. With this patch, the InfoFrames are sent. Previously, I wrote a
patch to 'touch the DIP registers after we enable the HDMI port' to
solve this same problem, but that patch doesn't seem to be needed
anymore after this patch.
All this patch does is revert a chunk of the following commit:
Paulo Zanoni [Mon, 28 May 2012 19:42:53 +0000 (16:42 -0300)]
drm/i915: explicitly disable the DIPs we're not using
From this point on, the 'set_infoframe' functions always set the DIP
registers to a known state, so anything done will always be undone at
the modeset.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Mon, 28 May 2012 19:42:52 +0000 (16:42 -0300)]
drm/i915: don't wait for vblank while writing InfoFrames
This function is called when the pipe is disabled, so it always gets
the 50ms timeout.
This function is called once for each InfoFrame, so we actually get a
100ms timeout. Will be more if we add more InfoFrames.
Also, the spec says we need to "wait for a VSync to ensure completion
of any pending DIP transmissions", not for a VBlank. OTOH, the
register documentation suggests that the DIPs are sent *during* the
VSync, so shouldn't we be waiting until *after* the VSync to ensure
all DIPs are sent?
So this wait_for_vblank seems, besides useless, totally wrong.
If we ever want to change some specific InfoFrame on-the-fly (outside
of the modeset code), the code that changes the InfoFrame will have to
do the waiting itself, and properly.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Mon, 28 May 2012 19:42:49 +0000 (16:42 -0300)]
drm/i915: properly alternate between DVI and HDMI
This solves problems that happen when you alternate between HDMI and
DVI on the same port. I can reproduce these problems using DP->HDMI
and DP->DVI adapters on a DP port.
When you first plug HDMI and then plug DVI, you need to stop sending
DIPs, even if the port is in DVI mode (see the HDMI register spec). If
you don't stop sending DIPs, you'll see a pink vertical line on the
left side of the screen, some modes will give you a black screen, some
modes won't work correctly.
When you first plug DVI and then plug HDMI, you need to properly
enable the DIPs, otherwise the HW won't send them. After spending a
lot of time investigating this, I concluded that if the DIPs are
disabled, we should not write to the DIP register again because when
we do this, we also set the AVI InfoFrame frequency to "once", and
this seems to really confuse our hardware. Since this problem was not
exactly easy to debug, I'm adopting the defensive behavior and not
just avoing the "disable twice" sequence, but also explicitly
selecting the AVI InfoFrame and setting its frequency to a correct
one.
Also, move the "is_dvi" check from intel_set_infoframe to the
set_infoframes functions since now they're going to be the first ones
to deal with the DIP registers.
This patch adds the code to fix the problem, but it depends on the
removal of some code that can't be removed right now and will come
later in the patch series. The patch that we need is:
- drm/i915: don't write 0 to DIP control at HDMI init
[danvet: Paulo clarified that this additional patch is only required
to make the fix complete, this patch here alone doesn't introduce a
regression but only partially solves the problem of randomly clearing
the dip registers.]
V2: Be even more defensive by selecting AVI and setting its frequency
outside the "is_dvi" check.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Mon, 28 May 2012 19:42:48 +0000 (16:42 -0300)]
drm/i915: add set_infoframes to struct intel_hdmi
We need a function that is able to fully 'set' the state of the DIP
registers to a known state.
Currently, we have the write_infoframe function that is called twice:
once for AVI and once for SPD. The problem is that write_infoframe
tries to keep the state of the DIP register as it is, changing only
the minimum necessary bits. The second problem is that
write_infoframe does twice (once for each time it is called) some
work that should be done only once (like waiting for vblank and
setting the port). If we add even more DIPs, it will do even more
repeated work.
This patch only adds the infrastructure keeping the code behavior the
same as before.
v2: add static keywords
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull ceph updates from Sage Weil:
"There are some updates and cleanups to the CRUSH placement code, a bug
fix with incremental maps, several cleanups and fixes from Josh Durgin
in the RBD block device code, a series of cleanups and bug fixes from
Alex Elder in the messenger code, and some miscellaneous bounds
checking and gfp cleanups/fixes."
Fix up trivial conflicts in net/ceph/{messenger.c,osdmap.c} due to the
networking people preferring "unsigned int" over just "unsigned".
* git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (45 commits)
libceph: fix pg_temp updates
libceph: avoid unregistering osd request when not registered
ceph: add auth buf in prepare_write_connect()
ceph: rename prepare_connect_authorizer()
ceph: return pointer from prepare_connect_authorizer()
ceph: use info returned by get_authorizer
ceph: have get_authorizer methods return pointers
ceph: ensure auth ops are defined before use
ceph: messenger: reduce args to create_authorizer
ceph: define ceph_auth_handshake type
ceph: messenger: check return from get_authorizer
ceph: messenger: rework prepare_connect_authorizer()
ceph: messenger: check prepare_write_connect() result
ceph: don't set WRITE_PENDING too early
ceph: drop msgr argument from prepare_write_connect()
ceph: messenger: send banner in process_connect()
ceph: messenger: reset connection kvec caller
libceph: don't reset kvec in prepare_write_banner()
ceph: ignore preferred_osd field
ceph: fully initialize new layout
...
Linus Torvalds [Wed, 30 May 2012 18:12:00 +0000 (11:12 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf updates from Ingo Molnar.
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (21 commits)
perf ui browser: Stop using 'self'
perf annotate browser: Read perf config file for settings
perf config: Allow '_' in config file variable names
perf annotate browser: Make feature toggles global
perf annotate browser: The idx_asm field should be used in asm only view
perf tools: Convert critical messages to ui__error()
perf ui: Make --stdio default when TUI is not supported
tools lib traceevent: Silence compiler warning on 32bit build
perf record: Fix branch_stack type in perf_record_opts
perf tools: Reconstruct event with modifiers from perf_event_attr
perf top: Fix counter name fixup when fallbacking to cpu-clock
perf tools: fix thread_map__new_by_pid_str() memory leak in error path
perf tools: Do not use _FORTIFY_SOURCE when DEBUG=1 is specified
tools lib traceevent: Fix signature of create_arg_item()
tools lib traceevent: Use proper function parameter type
tools lib traceevent: Fix freeing arg on process_dynamic_array()
tools lib traceevent: Fix a possibly wrong memory dereference
tools lib traceevent: Fix a possible memory leak
tools lib traceevent: Allow expressions in __print_symbolic() fields
perf evlist: Explicititely initialize input_name
...
Linus Torvalds [Wed, 30 May 2012 17:03:46 +0000 (10:03 -0700)]
Merge branch 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
Pull i2c updates from Jean Delvare.
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c: Split I2C_M_NOSTART support out of I2C_FUNC_PROTOCOL_MANGLING
i2c-dev: Add support for I2C_M_RECV_LEN
Linus Torvalds [Wed, 30 May 2012 16:59:13 +0000 (09:59 -0700)]
Merge git://www.linux-watchdog.org/linux-watchdog
Pull second set of watchdog updates from Wim Van Sebroeck:
"This changeset contains following changes:
* Add support for multiple watchdog devices. We use dynamically
allocated device id's for this.
* Add locking into the generic watchdog infrastructure.
* Add support for dynamically allocated watchdog_device structs so
that we can deal with devices that get unbound.
* convert following drivers to the generic watchdog framework:
sch5627, sch5636 and sp805_wdt.
* Add DA9052/53 PMIC watchdog support
* Fix printk format warnings for iTCO_wdt.c"
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: iTCO_wdt.c: fix printk format warnings
watchdog: sp805_wdt: Add clk_{un}prepare support
watchdog: sp805_wdt: convert to watchdog core
hwmon/sch56xx: Depend on watchdog for watchdog core functions
watchdog: sch56xx-common: set correct bits in register()
Watchdog: DA9052/53 PMIC watchdog support
watchdog: sch56xx-common: Add proper ref-counting of watchdog data
watchdog: sch56xx: Remove unnecessary checks for register changes
watchdog: sch56xx: Use watchdog core
watchdog: Add support for dynamically allocated watchdog_device structs
watchdog: Add Locking support
watchdog: watchdog_dev: Rewrite wrapper code
watchdog: use dev_ functions
watchdog: create all the proper device files
watchdog: Add a flag to indicate the watchdog doesn't reboot things
watchdog: Add multiple device support
watchdog: watchdog_core.h: make functions extern
watchdog: correct the name of the watchdog_core inlude file
watchdog: Add watchdog_active() routine
watchdog: watchdog_dev: include private header to pickup global symbol prototypes
Linus Torvalds [Wed, 30 May 2012 16:55:53 +0000 (09:55 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Just regular fixes, bunch from intel, quieting some of the over
zealous power warnings, and the rest just misc.
I've got another pull with the remaining dma-buf bits, since the vmap
bits are in your tree now. I'll send tomorrow just to space things
out a bit."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (22 commits)
drm/edid/quirks: ViewSonic VA2026w
drm/udl: remove unused variables.
drm/radeon: fix XFX quirk
drm: Use stdint types for consistency
drm: Constify params to format_check() and framebuffer_checks()
drm/radeon: fix typo in trinity tiling setup
drm/udl: unlock before returning in udl_gem_mmap()
radeon: make radeon_cs_update_pages static.
drm/i915: tune down the noise of the RP irq limit fail
drm/i915: Remove the error message for unbinding pinned buffers
drm/i915: Limit page allocations to lowmem (dma32) for i965
drm/i915: always use RPNSWREQ for turbo change requests
drm/i915: reject doubleclocked cea modes on dp
drm/i915: Adding TV Out Missing modes.
drm/i915: wait for a vblank to pass after tv detect
drm/i915: no lvds quirk for HP t5740e Thin Client
drm/i915: enable vdd when switching off the eDP panel
drm/i915: Fix PCH PLL assertions to not assume CRTC:PLL relationship
drm/i915: Always update RPS interrupts thresholds along with frequency
drm/i915: properly handle interlaced bit for sdvo dtd conversion
...
Linus Torvalds [Wed, 30 May 2012 16:05:47 +0000 (09:05 -0700)]
Merge branch 'for-3.5/drivers' of git://git.kernel.dk/linux-block
Pull block driver updates from Jens Axboe:
"Here are the driver related changes for 3.5. It contains:
- The floppy changes from Jiri. Jiri is now also marked as the
maintainer of floppy.c, I shall be publically branding his forehead
with red hot iron at the next opportune moment.
- A batch of drbd updates and fixes from the linbit crew, as well as
fixes from others.
- Two small fixes for xen-blkfront courtesy of Jan."
* 'for-3.5/drivers' of git://git.kernel.dk/linux-block: (70 commits)
floppy: take over maintainership
floppy: remove floppy-specific O_EXCL handling
floppy: convert to delayed work and single-thread wq
xen-blkfront: module exit handling adjustments
xen-blkfront: properly name all devices
drbd: grammar fix in log message
drbd: check MODULE for THIS_MODULE
drbd: Restore the request restart logic
drbd: introduce a bio_set to allocate housekeeping bios from
drbd: remove unused define
drbd: bm_page_async_io: properly initialize page->private
drbd: use the newly introduced page pool for bitmap IO
drbd: add page pool to be used for meta data IO
drbd: allow bitmap to change during writeout from resync_finished
drbd: fix race between drbdadm invalidate/verify and finishing resync
drbd: fix resend/resubmit of frozen IO
drbd: Ensure that data_size is not 0 before using data_size-1 as index
drbd: Delay/reject other state changes while establishing a connection
drbd: move put_ldev from __req_mod() to the endio callback
drbd: fix WRITE_ACKED_BY_PEER_AND_SIS to not set RQ_NET_DONE
...
Linus Torvalds [Wed, 30 May 2012 15:52:42 +0000 (08:52 -0700)]
Merge branch 'for-3.5/core' of git://git.kernel.dk/linux-block
Merge block/IO core bits from Jens Axboe:
"This is a bit bigger on the core side than usual, but that is purely
because we decided to hold off on parts of Tejun's submission on 3.4
to give it a bit more time to simmer. As a consequence, it's seen a
long cycle in for-next.
It contains:
- Bug fix from Dan, wrong locking type.
- Relax splice gifting restriction from Eric.
- A ton of updates from Tejun, primarily for blkcg. This improves
the code a lot, making the API nicer and cleaner, and also includes
fixes for how we handle and tie policies and re-activate on
switches. The changes also include generic bug fixes.
- A simple fix from Vivek, along with a fix for doing proper delayed
allocation of the blkcg stats."
Fix up annoying conflict just due to different merge resolution in
Documentation/feature-removal-schedule.txt
* 'for-3.5/core' of git://git.kernel.dk/linux-block: (92 commits)
blkcg: tg_stats_alloc_lock is an irq lock
vmsplice: relax alignement requirements for SPLICE_F_GIFT
blkcg: use radix tree to index blkgs from blkcg
blkcg: fix blkcg->css ref leak in __blkg_lookup_create()
block: fix elvpriv allocation failure handling
block: collapse blk_alloc_request() into get_request()
blkcg: collapse blkcg_policy_ops into blkcg_policy
blkcg: embed struct blkg_policy_data in policy specific data
blkcg: mass rename of blkcg API
blkcg: style cleanups for blk-cgroup.h
blkcg: remove blkio_group->path[]
blkcg: blkg_rwstat_read() was missing inline
blkcg: shoot down blkgs if all policies are deactivated
blkcg: drop stuff unused after per-queue policy activation update
blkcg: implement per-queue policy activation
blkcg: add request_queue->root_blkg
blkcg: make request_queue bypassing on allocation
blkcg: make sure blkg_lookup() returns %NULL if @q is bypassing
blkcg: make blkg_conf_prep() take @pol and return with queue lock held
blkcg: remove static policy ID enums
...
Linus Torvalds [Wed, 30 May 2012 15:49:28 +0000 (08:49 -0700)]
Merge tag 'iommu-updates-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
"Not much stuff this time. The only change to the IOMMU core code is
the addition of a handle to the fault handling code. A few updates to
the AMD IOMMU driver to work around new errata. The other patches are
mostly fixes and enhancements to the existing ARM IOMMU drivers and
documentation updates.
A new IOMMU driver for the Exynos platform was also underway but got
merged via the Samsung tree and is not part of this tree."
* tag 'iommu-updates-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
Documentation: kernel-parameters.txt Add amd_iommu_dump
iommu/core: pass a user-provided token to fault handlers
iommu/tegra: gart: Fix register offset correctly
iommu: OMAP: device detach on domain destroy
iommu: tegra/gart: Add device tree support
iommu: tegra/gart: use correct gart_device
iommu/tegra: smmu: Print device name correctly
iommu/amd: Add workaround for event log erratum
iommu/amd: Check for the right TLP prefix bit
dma-debug: release free_entries_lock before saving stack trace
Dave Hansen [Wed, 30 May 2012 14:51:07 +0000 (07:51 -0700)]
mm: fix vma_resv_map() NULL pointer
hugetlb_reserve_pages() can be used for either normal file-backed
hugetlbfs mappings, or MAP_HUGETLB. In the MAP_HUGETLB, semi-anonymous
mode, there is not a VMA around. The new call to resv_map_put() assumed
that there was, and resulted in a NULL pointer dereference:
Mark Brown [Wed, 30 May 2012 08:55:34 +0000 (10:55 +0200)]
i2c: Split I2C_M_NOSTART support out of I2C_FUNC_PROTOCOL_MANGLING
Since there are uses for I2C_M_NOSTART which are much more sensible and
standard than most of the protocol mangling functionality (the main one
being gather writes to devices where something like a register address
needs to be inserted before a block of data) create a new I2C_FUNC_NOSTART
for this feature and update all the users to use it.
Also strengthen the disrecommendation of the protocol mangling while we're
at it.
In the case of regmap-i2c we remove the requirement for mangling as
I2C_M_NOSTART is the only mangling feature which is being used.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Jean Delvare [Wed, 30 May 2012 08:55:34 +0000 (10:55 +0200)]
i2c-dev: Add support for I2C_M_RECV_LEN
As the bus driver side implementation of I2C_M_RECV_LEN is heavily
tied to SMBus, we can't support received length over 32 bytes, but
let's at least support that.
In practice, the caller will have to setup a buffer large enough to
cover the case where received length byte has value 32, so minimum
32 + 1 = 33 bytes, possibly more if there is a fixed number of bytes
added for the specific slave (for example a checksum.)
Signed-off-by: Jean Delvare <khali@linux-fr.org> Tested-by: Douglas Gilbert <dgilbert@interlog.com>
Randy Dunlap [Mon, 14 May 2012 20:15:20 +0000 (13:15 -0700)]
watchdog: iTCO_wdt.c: fix printk format warnings
Fix printk format warnings:
drivers/watchdog/iTCO_wdt.c:577:3: warning: format '%04llx' expects type 'long long unsigned int', but argument 2 has type 'resource_size_t'
drivers/watchdog/iTCO_wdt.c:594:3: warning: format '%04llx' expects type 'long long unsigned int', but argument 2 has type 'resource_size_t'
drivers/watchdog/iTCO_wdt.c:600:2: warning: format '%04llx' expects type 'long long unsigned int', but argument 4 has type 'resource_size_t'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Viresh Kumar [Mon, 12 Mar 2012 04:22:16 +0000 (09:52 +0530)]
watchdog: sp805_wdt: convert to watchdog core
This patch converts existing sp805 watchdog driver to use already in place
common infrastructure present in watchdog core. With this lot of code goes away.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Hans de Goede [Thu, 24 May 2012 20:18:58 +0000 (22:18 +0200)]
hwmon/sch56xx: Depend on watchdog for watchdog core functions
Since the watchdog code in sch56xx-common now uses the watchdog core, the
Kconfig entires for the sch5627 and sch5636 should depend on WATCHDOG
being set. Also select the watchdog core when we select one of the drivers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Dan Carpenter [Thu, 24 May 2012 15:58:02 +0000 (18:58 +0300)]
watchdog: sch56xx-common: set correct bits in register()
WDOG_NO_WAY_OUT (3) and WDOG_ACTIVE (0) are the bit numbers, not a mask.
So "data->wddev.status |= WDOG_ACTIVE;" was intended to set bit zero but
it is a no-op.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Hans de Goede [Tue, 22 May 2012 09:40:25 +0000 (11:40 +0200)]
watchdog: sch56xx: Remove unnecessary checks for register changes
Since the watchdog core keeps track of the watchdog's active state, start/stop
will never get called when no changes are necessary. So we can remove the
check for the output_enable register changing before writing it (which is
an expensive operation).
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Hans de Goede [Tue, 22 May 2012 09:40:26 +0000 (11:40 +0200)]
watchdog: Add support for dynamically allocated watchdog_device structs
If a driver's watchdog_device struct is part of a dynamically allocated
struct (which it often will be), merely locking the module is not enough,
even with a drivers module locked, the driver can be unbound from the device,
examples:
1) The root user can unbind it through sysfd
2) The i2c bus master driver being unloaded for an i2c watchdog
I will gladly admit that these are corner cases, but we still need to handle
them correctly.
The fix for this consists of 2 parts:
1) Add ref / unref operations, so that the driver can refcount the struct
holding the watchdog_device struct and delay freeing it until any
open filehandles referring to it are closed
2) Most driver operations will do IO on the device and the driver should not
do any IO on the device after it has been unbound. Rather then letting each
driver deal with this internally, it is better to ensure at the watchdog
core level that no operations (other then unref) will get called after
the driver has called watchdog_unregister_device(). This actually is the
bulk of this patch.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Hans de Goede [Tue, 22 May 2012 09:40:26 +0000 (11:40 +0200)]
watchdog: Add Locking support
This patch fixes some potential multithreading issues, despite only
allowing one process to open the /dev/watchdog device, we can still get
called multiple times at the same time, since a program could be using thread,
or could share the fd after a fork.
This causes 2 potential problems:
1) watchdog_start / open do an unlocked test_n_set / test_n_clear,
if these 2 race, the watchdog could be stopped while the active
bit indicates it is running or visa versa.
2) Most watchdog_dev drivers probably assume that only one
watchdog-op will get called at a time, this is not necessary
true atm.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Alan Cox [Fri, 11 May 2012 10:00:19 +0000 (12:00 +0200)]
watchdog: Add a flag to indicate the watchdog doesn't reboot things
Some watchdogs merely trigger external alarms and controls. In a managed
environment this is very useful but we want drivers to be able to figure
out which is which now multiple dogs can be loaded. Thus add an ALARMONLY
feature flag.
Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Alan Cox [Thu, 10 May 2012 19:48:59 +0000 (21:48 +0200)]
watchdog: Add multiple device support
We keep the old /dev/watchdog interface file for the first watchdog via
miscdev. This is basically a cut and paste of the relevant interface code
from the rtc driver layer tweaked for watchdog.
Revised to fix problems noted by Hans de Goede
Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
watchdog: watchdog_dev: include private header to pickup global symbol prototypes
Include the private watchdog_dev.h header to pickup the prototypes for the
watchdog_dev_register/unregister functions.
This quiets the following sparse warnings:
warning: symbol 'watchdog_dev_register' was not declared. Should it be static?
warning: symbol 'watchdog_dev_unregister' was not declared. Should it be static?
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Linus Torvalds [Wed, 30 May 2012 03:14:53 +0000 (20:14 -0700)]
Merge branch 'x86-trampoline-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 trampoline rework from H. Peter Anvin:
"This code reworks all the "trampoline"/"realmode" code (various bits
that need to live in the first megabyte of memory, most but not all of
which runs in real mode at some point) in the kernel into a single
object. The main reason for doing this is that it eliminates the last
place in the kernel where we needed pages to be mapped RWX. This code
separates all that code into proper R/RW/RX pages."
Fix up conflicts in arch/x86/kernel/Makefile (mca removed next to reboot
code), and arch/x86/kernel/reboot.c (reboot code moved around in one
branch, modified in this one), and arch/x86/tools/relocs.c (mostly same
code came in earlier due to working around the ld bugs just before the
3.4 release).
Also remove stale x86-relocs entry from scripts/.gitignore as per Peter
Anvin.
* commit '61f5446169046c217a5479517edac3a890c3bee7': (36 commits)
x86, realmode: Move end signature into header.S
x86, relocs: When printing an error, say relative or absolute
x86, relocs: More relocations which may end up as absolute
x86, relocs: Workaround for binutils 2.22.52.0.1 section bug
xen-acpi-processor: Add missing #include <xen/xen.h>
acpi, bgrd: Add missing <linux/io.h> to drivers/acpi/bgrt.c
x86, realmode: Change EFER to a single u64 field
x86, realmode: Move kernel/realmode.c to realmode/init.c
x86, realmode: Move not-common bits out of trampoline_common.S
x86, realmode: Mask out EFER.LMA when saving trampoline EFER
x86, realmode: Fix no cache bits test in reboot_32.S
x86, realmode: Make sure all generated files are listed in targets
x86, realmode: build fix: remove duplicate build
x86, realmode: read cr4 and EFER from kernel for 64-bit trampoline
x86, realmode: fixes compilation issue in tboot.c
x86, realmode: move relocs from scripts/ to arch/x86/tools
x86, realmode: header for trampoline code
x86, realmode: flattened rm hierachy
x86, realmode: don't copy real_mode_header
x86, realmode: fix 64-bit wakeup sequence
...
Pull EDAC internal API changes from Mauro Carvalho Chehab:
"This changeset is the first part of a series of patches that fixes the
EDAC sybsystem. On this set, it changes the Kernel EDAC API in order
to properly represent the Intel i3/i5/i7, Xeon 3xxx/5xxx/7xxx, and
Intel E5-xxxx memory controllers.
The EDAC core used to assume that:
- the DRAM chip select pin is directly accessed by the memory
controller
- when multiple channels are used, they're all filled with the
same type of memory.
None of the above premises is true on Intel memory controllers since
2002, when RAMBUS and FB-DIMMs were introduced, and Advanced Memory
Buffer or by some similar technologies hides the direct access to the
DRAM pins.
So, the existing drivers for those chipsets had to lie to the EDAC
core, in general telling that just one channel is filled. That
produces some hard to understand error messages like:
EDAC MC0: CE row 3, channel 0, label "DIMM1": 1 Unknown error(s): memory read error on FATAL area : cpu=0 Err=0008:00c2 (ch=2), addr = 0xad1f73480 => socket=0, Channel=0(mask=2), rank=1
The location information there (row3 channel 0) is completely bogus:
it has no physical meaning, and are just some random values that the
driver uses to talk with the EDAC core. The error actually happened
at CPU socket 0, channel 0, slot 1, but this is not reported anywhere,
as the EDAC core doesn't know anything about the memory layout. So,
only advanced users that know how the EDAC driver works and that tests
their systems to see how DIMMs are mapped can actually benefit for
such error logs.
This patch series fixes the error report logic, in order to allow the
EDAC to expose the memory architecture used by them to the EDAC core.
So, as the EDAC core now understands how the memory is organized, it
can provide an useful report:
The location of the DIMM where the error happened is reported by "MC0"
(cpu socket #0), at "channel:0 slot:1" location, and matches the
physical location of the DIMM.
There are two remaining issues not covered by this patch series:
- The EDAC sysfs API will still report bogus values. So,
userspace tools like edac-utils will still use the bogus data;
- Add a new tracepoint-based way to get the binary information
about the errors.
Those are on a second series of patches (also at -next), but will
probably miss the train for 3.5, due to the slow review process."
Fix up trivial conflict (due to spelling correction of removed code) in
drivers/edac/edac_device.c
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac: (42 commits)
i7core: fix ranks information at the per-channel struct
i5000: Fix the fatal error handling
i5100_edac: Fix a warning when compiled with 32 bits
i82975x_edac: Test nr_pages earlier to save a few CPU cycles
e752x_edac: provide more info about how DIMMS/ranks are mapped
i5000_edac: Fix the logic that retrieves memory information
i5400_edac: improve debug messages to better represent the filled memory
edac: Cleanup the logs for i7core and sb edac drivers
edac: Initialize the dimm label with the known information
edac: Remove the legacy EDAC ABI
x38_edac: convert driver to use the new edac ABI
tile_edac: convert driver to use the new edac ABI
sb_edac: convert driver to use the new edac ABI
r82600_edac: convert driver to use the new edac ABI
ppc4xx_edac: convert driver to use the new edac ABI
pasemi_edac: convert driver to use the new edac ABI
mv64x60_edac: convert driver to use the new edac ABI
mpc85xx_edac: convert driver to use the new edac ABI
i82975x_edac: convert driver to use the new edac ABI
i82875p_edac: convert driver to use the new edac ABI
...
Linus Torvalds [Wed, 30 May 2012 01:27:19 +0000 (18:27 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
"The whole series has been sitting in -next for quite a while with no
complaints. The last change to the series was before the weekend the
removal of an SPI patch which Grant - even though previously acked by
himself - appeared to raise objections. So I removed it until the
situation is clarified. Other than that all the patches have the acks
from their respective maintainers, all MIPS and x86 defconfigs are
building fine and I'm not aware of any problems introduced by this
series.
Among the key features for this patch series is a sizable patchset for
Lantiq which among other things introduces support for Lantiq's
flagship product, the FALCON SOC. It also means that the opensource
developers behind this patchset have overtaken Lantiq's competing
inhouse development team that was working behind closed doors.
Less noteworthy the ath79 patchset which adds support for a few more
chip variants, cleanups and fixes. Finally the usual dose of tweaking
of generic code."
Fix up trivial conflicts in arch/mips/lantiq/xway/gpio_{ebu,stp}.c where
printk spelling fixes clashed with file move and eventual removal of the
printk.
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (81 commits)
MIPS: lantiq: remove orphaned code
MIPS: Remove all -Wall and almost all -Werror usage from arch/mips.
MIPS: lantiq: implement support for FALCON soc
MTD: MIPS: lantiq: verify that the NOR interface is available on falcon soc
MTD: MIPS: lantiq: implement OF support
watchdog: MIPS: lantiq: implement OF support and minor fixes
SERIAL: MIPS: lantiq: implement OF support
GPIO: MIPS: lantiq: convert gpio-stp-xway to OF
GPIO: MIPS: lantiq: convert gpio-mm-lantiq to OF and of_mm_gpio
GPIO: MIPS: lantiq: move gpio-stp and gpio-ebu to the subsystem folder
MIPS: pci: convert lantiq driver to OF
MIPS: lantiq: convert dma to platform driver
MIPS: lantiq: implement support for clkdev api
MIPS: lantiq: drop ltq_gpio_request() and gpio_to_irq()
OF: MIPS: lantiq: implement irq_domain support
OF: MIPS: lantiq: implement OF support
MIPS: lantiq: drop mips_machine support
OF: PCI: const usage needed by MIPS
MIPS: Cavium: Remove smp_reserve_lock.
MIPS: Move cache setup to setup_arch().
...
Linus Torvalds [Wed, 30 May 2012 01:21:44 +0000 (18:21 -0700)]
Merge branch 'for-linus' of git://git.linaro.org/people/rmk/linux-arm
Pull arm updates from Russell King:
"This contains both some fixes found when trying to get the
Assabet+neponset setup as a replacement firewall with a 3c589 PCMCIA
card, and a bunch of changes from Al to fix up the ARM signal
handling, particularly some of the restart behaviour."
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm:
ARM: neponset: make sure neponset_ncr_frob() is exported
ARM: fix out[bwl]()
arm: don't open-code ptrace_report_syscall()
arm: bury unused _TIF_RESTORE_SIGMASK
arm: remove unused restart trampoline
arm: new way of handling ERESTART_RESTARTBLOCK
arm: if we get into work_pending while returning to kernel mode, just go away
arm: don't call try_to_freeze() from do_signal()
arm: if there's no handler we need to restore sigmask, syscall or no syscall
arm: trim _TIF_WORK_MASK, get rid of useless test and branch...
arm: missing checks of __get_user()/__put_user() return values
Linus Torvalds [Wed, 30 May 2012 01:05:31 +0000 (18:05 -0700)]
Merge branch 'akpm' (Andrew's patch-bomb)
Merge patches through Andrew Morton:
"180 patches - err 181 - listed below:
- most of MM. I held back the (large) "memcg: add hugetlb extension"
series because a bunfight has recently broken out.
- leds. After this, Bryan Wu will be handling drivers/leds/
- backlight
- lib/
- rtc"
* emailed from Andrew Morton <akpm@linux-foundation.org>: (181 patches)
drivers/rtc/rtc-s3c.c: fix compiler warning
drivers/rtc/rtc-tegra.c: clean up probe/remove routines
drivers/rtc/rtc-pl031.c: remove RTC timer interrupt handling
drivers/rtc/rtc-lpc32xx.c: add device tree support
drivers/rtc/rtc-m41t93.c: don't let get_time() reset M41T93_FLAG_OF
rtc: ds1307: add trickle charger support
rtc: ds1307: remove superfluous initialization
rtc: rename CONFIG_RTC_MXC to CONFIG_RTC_DRV_MXC
drivers/rtc/Kconfig: place RTC_DRV_IMXDI and RTC_MXC under "on-CPU RTC drivers"
drivers/rtc/rtc-pcf8563.c: add RTC_VL_READ/RTC_VL_CLR ioctl feature
rtc: add ioctl to get/clear battery low voltage status
drivers/rtc/rtc-ep93xx.c: convert to use module_platform_driver()
rtc/spear: add Device Tree probing capability
lib/vsprintf.c: "%#o",0 becomes '0' instead of '00'
radix-tree: fix preload vector size
spinlock_debug: print kallsyms name for lock
vsprintf: fix %ps on non symbols when using kallsyms
lib/bitmap.c: fix documentation for scnprintf() functions
lib/string_helpers.c: make arrays static
lib/test-kstrtox.c: mark const init data with __initconst instead of __initdata
...
perf annotate browser: Make feature toggles global
So that when navigating to another function from a call site or when
going to another annotation browser thru the main report/top browser the
options (hide source code, jump arrows, jumpy lines, etc) remains the
last ones selected.
Cc: David Ahern <dsahern@gmail.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Mike Galbraith <efault@gmx.de> Cc: Namhyung Kim <namhyung@gmail.com> Cc: Paul Mackerras <paulus@samba.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Link: http://lkml.kernel.org/n/tip-0h0tah1zj59p01581snjufne@git.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
perf annotate browser: The idx_asm field should be used in asm only view
When hide_src_view is true we can't use browser_disasm_line->idx, that
takes into account also non asm lines, we must use browser_disasm_line->idx_asm
instead, otherwise we may end up with an index after the number of
entries, oops, fix it.
Cc: David Ahern <dsahern@gmail.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Mike Galbraith <efault@gmx.de> Cc: Namhyung Kim <namhyung@gmail.com> Cc: Paul Mackerras <paulus@samba.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Link: http://lkml.kernel.org/n/tip-o1szpyjh3z87yi0n6x0cr8uu@git.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Hannu Heikkinen [Tue, 29 May 2012 22:07:40 +0000 (15:07 -0700)]
drivers/rtc/rtc-tegra.c: clean up probe/remove routines
Use the devres managed resource functions in the probe routine. Also
affects the remove routine where the previously used free and release
functions are not needed.
The devm_* functions eliminate the need for manual resource releasing and
simplify error handling. Resources allocated by devm_* are freed
automatically on driver detach.
Signed-off-by: Hannu Heikkinen <ext-hannu.m.heikkinen@nokia.com> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Cc: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove RTT interrupt handling, since PIE mode interrupts are now better
emulated in generic code via an hrtimer we have no need for this, and
there is no codepath in the driver that enables these periodic interrupts
anyway.
Nikolaus Voss [Tue, 29 May 2012 22:07:39 +0000 (15:07 -0700)]
drivers/rtc/rtc-m41t93.c: don't let get_time() reset M41T93_FLAG_OF
If the rtc reports the time might be invalid due to oscillator failure,
M41T93_FLAG_OF flag must not be reset by get_time() as the read operation
doesn't make the time valid.
Without this patch, only the first get_time() reported an invalid time,
the second get_time() reported a valid time althought the reported time is
probably wrong due to oscillator failure.
Instead of resetting in get_time(), with this patch M41T93_FLAG_OF is
reset in set_time() when a valid time is to be written.
Signed-off-by: Nikolaus Voss <n.voss@weinmann.de> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Wolfram Sang [Tue, 29 May 2012 22:07:38 +0000 (15:07 -0700)]
rtc: ds1307: add trickle charger support
Some DS13XX devices have "trickle chargers". Its configuration register
is at different locations, the setup is the same, though. Since the
configuration is board specific, introduce a platform_data to this driver.
Tested with a DS1339 on a custom board.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Cc: Alessandro Zummo <alessandro.zummo@towertech.it> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexander Stein [Tue, 29 May 2012 22:07:36 +0000 (15:07 -0700)]
rtc: add ioctl to get/clear battery low voltage status
Currently there is no generic way to get the RTC battery status within an
application. So add an ioctl to read the status bit. The idea is that
the bit is set once a low voltage is detected. It stays there until it is
reset using the RTC_VL_CLR ioctl.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Viresh Kumar [Tue, 29 May 2012 22:07:35 +0000 (15:07 -0700)]
rtc/spear: add Device Tree probing capability
SPEAr platforms now support DT and so must convert all drivers support DT.
This patch adds DT probing support for rtc and updates its documentation
too.
Signed-off-by: Pierre Carrier <pierre@spotify.com> Acked-by: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Joe Perches <joe@perches.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stephen Boyd [Tue, 29 May 2012 22:07:34 +0000 (15:07 -0700)]
spinlock_debug: print kallsyms name for lock
When a spinlock warning is printed we usually get
BUG: spinlock bad magic on CPU#0, modprobe/111
lock: 0xdff09f38, .magic: 00000000, .owner: /0, .owner_cpu: 0
but it's nicer to print the symbol for the lock if we have it so that we
can avoid 'grep dff09f38 /proc/kallsyms' to find out which lock it was.
Use kallsyms to print the symbol name so we get something a bit easier to
read
BUG: spinlock bad magic on CPU#0, modprobe/112
lock: test_lock, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0
If the lock is not in kallsyms %ps will fall back to printing the address
directly.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Cc: Ingo Molnar <mingo@elte.hu> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stephen Boyd [Tue, 29 May 2012 22:07:33 +0000 (15:07 -0700)]
vsprintf: fix %ps on non symbols when using kallsyms
Using %ps in a printk format will sometimes fail silently and print the
empty string if the address passed in does not match a symbol that
kallsyms knows about. But using %pS will fall back to printing the full
address if kallsyms can't find the symbol. Make %ps act the same as %pS
by falling back to printing the address.
While we're here also make %ps print the module that a symbol comes from
so that it matches what %pS already does. Take this simple function for
example (in a module):
Andrew Morton [Tue, 29 May 2012 22:07:32 +0000 (15:07 -0700)]
lib/bitmap.c: fix documentation for scnprintf() functions
The code comments for bscnl_emit() and bitmap_scnlistprintf() are
describing snprintf() return semantics, but these functions use
scnprintf() return semantics. Fix that, and document the
bitmap_scnprintf() return value as well.
Uwe Kleine-König [Tue, 29 May 2012 22:07:31 +0000 (15:07 -0700)]
lib/test-kstrtox.c: mark const init data with __initconst instead of __initdata
As long as there is no other non-const variable marked __initdata in the
same compilation unit it doesn't hurt. If there were one however
compilation would fail with
error: $variablename causes a section type conflict
because a section containing const variables is marked read only and so
cannot contain non-const variables.
Chris Metcalf [Tue, 29 May 2012 22:07:31 +0000 (15:07 -0700)]
list_debug: WARN for adding something already in the list
We were bitten by this at one point and added an additional sanity test
for DEBUG_LIST. You can't validly add a list_head to a list where either
prev or next is the same as the thing you're adding.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com> Cc: Andi Kleen <andi@firstfloor.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexander Stein [Tue, 29 May 2012 22:07:30 +0000 (15:07 -0700)]
drivers/leds/leds-pca955x.c: fix race condition while setting brightness on several LEDs
When issuing the following command:
for I in 0 1 2 3 4 5 6 7; do
echo 0 > /sys/class/leds/pca955x\:${I}/brightness;
done
It is possible that all the pca955x_read_ls calls are done sequentially
before any pca955x_write_ls call is done. This updates the LS only to
the last LED update in its set.
Fix this by using a global lock for the pca995x device during
pca955x_led_work. Also used a struct for shared data betreen all LEDs.
[akpm@linux-foundation.org: revert unintentional rename of pca955x_ledsel()] Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com> Cc: Richard Purdie <rpurdie@rpsys.net> Cc: Bryan Wu <bryan.wu@canonical.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Shuah Khan [Tue, 29 May 2012 22:07:30 +0000 (15:07 -0700)]
leds: add new transient trigger for one shot timer activation
The leds timer trigger does not currently have an interface to activate a
one shot timer. The current support allows for setting two timers, one
for specifying how long a state to be on, and the second for how long the
state to be off. The delay_on value specifies the time period an LED
should stay in on state, followed by a delay_off value that specifies how
long the LED should stay in off state. The on and off cycle repeats until
the trigger gets deactivated. There is no provision for one time
activation to implement features that require an on or off state to be
held just once and then stay in the original state forever.
Without one shot timer interface, user space can still use timer trigger
to set a timer to hold a state, however when user space application
crashes or goes away without deactivating the timer, the hardware will be
left in that state permanently.
As a specific example of this use-case, let's look at vibrate feature on
phones. Vibrate function on phones is implemented using PWM pins on SoC
or PMIC. There is a need to activate one shot timer to control the
vibrate feature, to prevent user space crashes leaving the phone in
vibrate mode permanently causing the battery to drain.
This trigger exports three properties, activate, state, and duration When
transient trigger is activated these properties are set to default values.
- duration allows setting timer value in msecs. The initial value is 0.
- activate allows activating and deactivating the timer specified by
duration as needed. The initial and default value is 0. This will allow
duration to be set after trigger activation.
- state allows user to specify a transient state to be held for the specified
duration.
Signed-off-by: Shuah Khan <shuahkhan@gmail.com> Cc: Jonas Bonn <jonas@southpole.se> Cc: Richard Purdie <rpurdie@rpsys.net> Cc: NeilBrown <neilb@suse.de> Cc: Bryan Wu <bryan.wu@canonical.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / karo-tx-linux.git / log