* U-boot - Configuration file for BF533 STAMP board
*/
-#ifndef __CONFIG_STAMP_H__
-#define __CONFIG_STAMP_H__
+#ifndef __CONFIG_BF533_STAMP_H__
+#define __CONFIG_BF533_STAMP_H__
-#include <asm/blackfin-config-pre.h>
+#include <asm/config-pre.h>
-#define CONFIG_RTC_BFIN 1
-
-#define CONFIG_PANIC_HANG 1
-
-#define CONFIG_BFIN_CPU bf533-0.3
-#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS
-
-/* This sets the default state of the cache on U-Boot's boot */
-#define CONFIG_ICACHE_ON
-#define CONFIG_DCACHE_ON
/*
- * Board settings
+ * Processor Settings
*/
-#define CONFIG_DRIVER_SMC91111 1
-#define CONFIG_SMC91111_BASE 0x20300300
-
-/* FLASH/ETHERNET uses the same address range */
-#define SHARED_RESOURCES 1
-
-/* Is I2C bit-banged? */
-#define CONFIG_SOFT_I2C 1
+#define CONFIG_BFIN_CPU bf533-0.3
+#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS
/*
- * Software (bit-bang) I2C driver configuration
+ * Clock Settings
+ * CCLK = (CLKIN * VCO_MULT) / CCLK_DIV
+ * SCLK = (CLKIN * VCO_MULT) / SCLK_DIV
*/
-#define PF_SCL PF3
-#define PF_SDA PF2
+/* CONFIG_CLKIN_HZ is any value in Hz */
+#define CONFIG_CLKIN_HZ 11059200
+/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */
+/* 1 = CLKIN / 2 */
+#define CONFIG_CLKIN_HALF 0
+/* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */
+/* 1 = bypass PLL */
+#define CONFIG_PLL_BYPASS 0
+/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */
+/* Values can range from 0-63 (where 0 means 64) */
+#define CONFIG_VCO_MULT 45
+/* CCLK_DIV controls the core clock divider */
+/* Values can be 1, 2, 4, or 8 ONLY */
+#define CONFIG_CCLK_DIV 1
+/* SCLK_DIV controls the system clock divider */
+/* Values can range from 1-15 */
+#define CONFIG_SCLK_DIV 6 /* note: 1.2 boards can go faster */
/*
- * Video splash screen support
+ * Memory Settings
*/
-#define CONFIG_VIDEO 0
-
-/*
- * Clock settings
- */
-
-/* CONFIG_CLKIN_HZ is any value in Hz */
-#define CONFIG_CLKIN_HZ 11059200
-/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN */
-/* 1=CLKIN/2 */
-#define CONFIG_CLKIN_HALF 0
-/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass */
-/* 1=bypass PLL */
-#define CONFIG_PLL_BYPASS 0
-/* CONFIG_VCO_MULT controls what the multiplier of the PLL is. */
-/* Values can range from 1-64 */
-#define CONFIG_VCO_MULT 36
-/* CONFIG_CCLK_DIV controls what the core clock divider is */
-/* Values can be 1, 2, 4, or 8 ONLY */
-#define CONFIG_CCLK_DIV 1
-/* CONFIG_SCLK_DIV controls what the peripheral clock divider is*/
-/* Values can range from 1-15 */
-#define CONFIG_SCLK_DIV 5
-/* CONFIG_SPI_BAUD controls the SPI peripheral clock divider */
-/* Values can range from 2-65535 */
-/* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD) */
-#define CONFIG_SPI_BAUD 2
-#define CONFIG_SPI_BAUD_INITBLOCK 4
+#define CONFIG_MEM_ADD_WDTH 11
+#define CONFIG_MEM_SIZE 128
-/*
- * Network settings
- */
+#define CONFIG_EBIU_SDRRC_VAL 0x268
+#define CONFIG_EBIU_SDGCTL_VAL 0x911109
-#if (CONFIG_DRIVER_SMC91111)
-#if 0
-#define CONFIG_MII
-#endif
+#define CONFIG_EBIU_AMGCTL_VAL 0xFF
+#define CONFIG_EBIU_AMBCTL0_VAL 0xBBC3BBC3
+#define CONFIG_EBIU_AMBCTL1_VAL 0x99B39983
-/* network support */
-#define CONFIG_IPADDR 192.168.0.15
-#define CONFIG_NETMASK 255.255.255.0
-#define CONFIG_GATEWAYIP 192.168.0.1
-#define CONFIG_SERVERIP 192.168.0.2
-#define CONFIG_HOSTNAME STAMP
-#define CONFIG_ROOTPATH /checkout/uClinux-dist/romfs
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024)
+#define CONFIG_SYS_MALLOC_LEN (384 * 1024)
-/* To remove hardcoding and enable MAC storage in EEPROM */
-/* #define CONFIG_ETHADDR 02:80:ad:20:31:b8 */
-#endif /* CONFIG_DRIVER_SMC91111 */
/*
- * Flash settings
+ * Network Settings
*/
-
-#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
-#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
-#define CONFIG_SYS_FLASH_CFI_AMD_RESET
-
-#define CONFIG_SYS_FLASH_BASE 0x20000000
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 67 /* max number of sectors on one chip */
-
-#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER)
-#define CONFIG_ENV_IS_IN_EEPROM 1
-#define CONFIG_ENV_OFFSET 0x4000
-#define CONFIG_ENV_HEADER (CONFIG_ENV_OFFSET + 0x12A) /* 0x12A is the length of LDR file header */
-#else
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_ADDR 0x20004000
-#define CONFIG_ENV_OFFSET (CONFIG_ENV_ADDR - CONFIG_SYS_FLASH_BASE)
-#endif
-
-#define CONFIG_ENV_SIZE 0x2000
-#define CONFIG_ENV_SECT_SIZE 0x2000 /* Total Size of Environment Sector */
-#define ENV_IS_EMBEDDED
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 30000 /* Timeout for Chip Erase (in ms) */
-#define CONFIG_SYS_FLASH_ERASEBLOCK_TOUT 5000 /* Timeout for Block Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 1 /* Timeout for Flash Write (in ms) */
-
-/* JFFS Partition offset set */
-#define CONFIG_SYS_JFFS2_FIRST_BANK 0
-#define CONFIG_SYS_JFFS2_NUM_BANKS 1
-/* 512k reserved for u-boot */
-#define CONFIG_SYS_JFFS2_FIRST_SECTOR 11
-
-/*
- * following timeouts shall be used once the
- * Flash real protection is enabled
- */
-#define CONFIG_SYS_FLASH_LOCK_TOUT 5 /* Timeout for Flash Set Lock Bit (in ms) */
-#define CONFIG_SYS_FLASH_UNLOCK_TOUT 10000 /* Timeout for Flash Clear Lock Bits (in ms) */
-
+#define ADI_CMDS_NETWORK 1
+#define CONFIG_SMC91111 1
+#define CONFIG_SMC91111_BASE 0x20300300
+#define SMC91111_EEPROM_INIT() \
+ do { \
+ bfin_write_FIO_DIR(bfin_read_FIO_DIR() | PF1 | PF0); \
+ bfin_write_FIO_FLAG_C(PF1); \
+ bfin_write_FIO_FLAG_S(PF0); \
+ SSYNC(); \
+ } while (0)
+#define CONFIG_HOSTNAME bf533-stamp
+/* Uncomment next line to use fixed MAC address */
+/* #define CONFIG_ETHADDR 02:80:ad:20:31:b8 */
+
+
+/* I2C */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED 50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE 0
/*
- * SDRAM settings & memory map
+ * Software (bit-bang) I2C driver configuration
*/
-
-#define CONFIG_MEM_SIZE 128 /* 128, 64, 32, 16 */
-#define CONFIG_MEM_ADD_WDTH 11 /* 8, 9, 10, 11 */
-#define CONFIG_MEM_MT48LC64M4A2FB_7E 1
-
-#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */
-
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-
-#define CONFIG_SYS_MAX_RAM_SIZE (CONFIG_MEM_SIZE * 1024 *1024)
-#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MAX_RAM_SIZE - 0x80000 - 1)
-#define CONFIG_LOADADDR 0x01000000
-
-#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-#define CONFIG_SYS_GBL_DATA_SIZE 0x4000 /* Reserve 16k for Global Data */
-#define CONFIG_STACKSIZE (128*1024) /* regular stack */
-
-#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_MAX_RAM_SIZE - 0x40000)
-#define CONFIG_SYS_MALLOC_BASE (CONFIG_SYS_MONITOR_BASE - CONFIG_SYS_MALLOC_LEN)
-#define CONFIG_SYS_GBL_DATA_ADDR (CONFIG_SYS_MALLOC_BASE - CONFIG_SYS_GBL_DATA_SIZE)
-#define CONFIG_STACKBASE (CONFIG_SYS_GBL_DATA_ADDR - 4)
-
-/* Check to make sure everything fits in SDRAM */
-#if ((CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) > CONFIG_SYS_MAX_RAM_SIZE)
- #error Memory Map does not fit into configuration
-#endif
-
-#if ( CONFIG_CLKIN_HALF == 0 )
-#define CONFIG_VCO_HZ ( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT )
-#else
-#define CONFIG_VCO_HZ (( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 )
-#endif
-
-#if (CONFIG_PLL_BYPASS == 0)
-#define CONFIG_CCLK_HZ ( CONFIG_VCO_HZ / CONFIG_CCLK_DIV )
-#define CONFIG_SCLK_HZ ( CONFIG_VCO_HZ / CONFIG_SCLK_DIV )
-#else
-#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ
-#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ
-#endif
+#define CONFIG_SOFT_I2C_GPIO_SCL GPIO_PF3
+#define CONFIG_SOFT_I2C_GPIO_SDA GPIO_PF2
/*
- * Command settings
+ * Flash Settings
*/
-
-#define CONFIG_SYS_LONGHELP 1
-#define CONFIG_CMDLINE_EDITING 1
-
-#define CONFIG_SYS_AUTOLOAD "no" /*rarpb, bootp or dhcp commands will perform only a */
-
-/* configuration lookup from the BOOTP/DHCP server, */
-/* but not try to load any image using TFTP */
-
-#define CONFIG_BOOTDELAY 5
-#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, currently its disabled */
-#define CONFIG_BOOTCOMMAND "run ramboot"
-
-#define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw console=ttyBF0,57600"
-
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):" \
- "$(rootpath) console=ttyBF0,57600\0" \
- "addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):" \
- "$(gatewayip):$(netmask):$(hostname):eth0:off\0" \
- "ramboot=tftpboot $(loadaddr) linux; " \
- "run ramargs;run addip;bootelf\0" \
- "nfsboot=tftpboot $(loadaddr) linux; " \
- "run nfsargs;run addip;bootelf\0" \
- "flashboot=bootm 0x20100000\0" \
- "update=tftpboot $(loadaddr) u-boot.bin; " \
- "protect off 0x20000000 0x2003FFFF; erase 0x20000000 0x2003FFFF;" \
- "cp.b $(loadaddr) 0x20000000 $(filesize)\0" \
- ""
-
-#ifdef CONFIG_SOFT_I2C
-#if (!CONFIG_SOFT_I2C)
-#undef CONFIG_SOFT_I2C
-#endif
-#endif
-
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_BASE 0x20000000
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_CFI_AMD_RESET
+#define CONFIG_SYS_MAX_FLASH_BANKS 1
+#define CONFIG_SYS_MAX_FLASH_SECT 67
/*
- * BOOTP options
+ * SPI Settings
*/
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BFIN_SPI
+#define CONFIG_ENV_SPI_MAX_HZ 30000000
+#define CONFIG_SF_DEFAULT_SPEED 30000000
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_ALL
/*
- * Command line configuration.
+ * Env Storage Settings
*/
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_DATE
-
-#if (CONFIG_DRIVER_SMC91111)
-#define CONFIG_CMD_PING
-#endif
-
-#if (CONFIG_SOFT_I2C)
-#define CONFIG_CMD_I2C
+#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER)
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_OFFSET 0x10000
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_SECT_SIZE 0x10000
+#else
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_OFFSET 0x4000
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET)
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_SECT_SIZE 0x2000
#endif
-
-#define CONFIG_CMD_DHCP
-
-
-/*
- * Console settings
- */
-
-#define CONFIG_BAUDRATE 57600
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
-
-#define CONFIG_SYS_PROMPT "bfin> " /* Monitor Command Prompt */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS)
+#define ENV_IS_EMBEDDED
#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_ENV_IS_EMBEDDED_IN_LDR
+#endif
+#ifdef ENV_IS_EMBEDDED
+/* WARNING - the following is hand-optimized to fit within
+ * the sector before the environment sector. If it throws
+ * an error during compilation remove an object here to get
+ * it linked after the configuration sector.
+ */
+# define LDS_BOARD_TEXT \
+ arch/blackfin/lib/built-in.o (.text*); \
+ arch/blackfin/cpu/built-in.o (.text*); \
+ . = DEFINED(env_offset) ? env_offset : .; \
+ common/env_embedded.o (.text*);
#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CONFIG_LOADS_ECHO 1
/*
- * I2C settings
- * By default PF2 is used as SDA and PF3 as SCL on the Stamp board
+ * I2C Settings
*/
-#if (CONFIG_SOFT_I2C)
-
-#define I2C_INIT (*pFIO_DIR |= PF_SCL); asm("ssync;")
-#define I2C_ACTIVE (*pFIO_DIR |= PF_SDA); *pFIO_INEN &= ~PF_SDA; asm("ssync;")
-#define I2C_TRISTATE (*pFIO_DIR &= ~PF_SDA); *pFIO_INEN |= PF_SDA; asm("ssync;")
-#define I2C_READ ((volatile)(*pFIO_FLAG_D & PF_SDA) != 0); asm("ssync;")
-#define I2C_SDA(bit) if(bit) { \
- *pFIO_FLAG_S = PF_SDA; \
- asm("ssync;"); \
- } \
- else { \
- *pFIO_FLAG_C = PF_SDA; \
- asm("ssync;"); \
- }
-#define I2C_SCL(bit) if(bit) { \
- *pFIO_FLAG_S = PF_SCL; \
- asm("ssync;"); \
- } \
- else { \
- *pFIO_FLAG_C = PF_SCL; \
- asm("ssync;"); \
- }
+#define CONFIG_SYS_I2C_SOFT
+#ifdef CONFIG_SYS_I2C_SOFT
+#define CONFIG_SYS_I2C
+#define CONFIG_SOFT_I2C_GPIO_SCL GPIO_PF3
+#define CONFIG_SOFT_I2C_GPIO_SDA GPIO_PF2
#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
-
-#define CONFIG_SYS_I2C_SPEED 50000
-#define CONFIG_SYS_I2C_SLAVE 0xFE
-#endif /* CONFIG_SOFT_I2C */
+#define CONFIG_SYS_I2C_SOFT_SPEED 50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE 0
+#endif
/*
- * Compact Flash settings
+ * Compact Flash / IDE / ATA Settings
*/
/* Enabled below option for CF support */
-/* #define CONFIG_STAMP_CF 1 */
-
-#if defined(CONFIG_STAMP_CF) && defined(CONFIG_CMD_IDE)
-
-#define CONFIG_MISC_INIT_R 1
+/* #define CONFIG_STAMP_CF */
+#if defined(CONFIG_STAMP_CF)
+#define CONFIG_MISC_INIT_R
#define CONFIG_DOS_PARTITION 1
-/*
- * IDE/ATA stuff
- */
#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
#undef CONFIG_IDE_LED /* no led for ide supported */
#undef CONFIG_IDE_RESET /* no reset for ide supported */
-#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE busses */
-#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
+#define CONFIG_SYS_IDE_MAXBUS 1
+#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS * 1)
#define CONFIG_SYS_ATA_BASE_ADDR 0x20200000
#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-#define CONFIG_SYS_ATA_DATA_OFFSET 0x0020 /* Offset for data I/O */
-#define CONFIG_SYS_ATA_REG_OFFSET 0x0020 /* Offset for normal register accesses */
-#define CONFIG_SYS_ATA_ALT_OFFSET 0x0007 /* Offset for alternate registers */
+#define CONFIG_SYS_ATA_DATA_OFFSET 0x0020 /* data I/O */
+#define CONFIG_SYS_ATA_REG_OFFSET 0x0020 /* normal register accesses */
+#define CONFIG_SYS_ATA_ALT_OFFSET 0x0007 /* alternate registers */
#define CONFIG_SYS_ATA_STRIDE 2
+
+#undef CONFIG_EBIU_AMBCTL1_VAL
+#define CONFIG_EBIU_AMBCTL1_VAL 0x99B3ffc2
#endif
+
/*
- * Miscellaneous configurable options
+ * Misc Settings
*/
+#define CONFIG_RTC_BFIN
+#define CONFIG_UART_CONSOLE 0
+#define CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED
-#define CONFIG_SYS_HZ 1000 /* 1ms time tick */
+/* FLASH/ETHERNET uses the same async bank */
+#define SHARED_RESOURCES 1
-#define CONFIG_SYS_BOOTM_LEN 0x4000000/* Large Image Length, set to 64 Meg */
+/* define to enable boot progress via leds */
+/* #define CONFIG_SHOW_BOOT_PROGRESS */
-#define CONFIG_SHOW_BOOT_PROGRESS 1 /* Show boot progress on LEDs */
+/* define to enable run status via led */
+/* #define CONFIG_STATUS_LED */
+#ifdef CONFIG_STATUS_LED
+#define CONFIG_GPIO_LED
+#define CONFIG_BOARD_SPECIFIC_LED
+/* use LED0 to indicate booting/alive */
+#define STATUS_LED_BOOT 0
+#define STATUS_LED_BIT GPIO_PF2
+#define STATUS_LED_STATE STATUS_LED_ON
+#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 4)
+/* use LED1 to indicate crash */
+#define STATUS_LED_CRASH 1
+#define STATUS_LED_BIT1 GPIO_PF3
+#define STATUS_LED_STATE1 STATUS_LED_ON
+#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2)
+/* #define STATUS_LED_BIT2 GPIO_PF4 */
+#endif
-#define CONFIG_SPI
+/* define to enable splash screen support */
+/* #define CONFIG_VIDEO */
-#ifdef CONFIG_VIDEO
-#if (CONFIG_VIDEO)
-#define CONFIG_SPLASH_SCREEN 1
-#define CONFIG_SILENT_CONSOLE 1
-#else
-#undef CONFIG_VIDEO
-#endif
-#endif
/*
- * FLASH organization and environment definitions
+ * Pull in common ADI header for remaining command/environment setup
*/
-
-#define CONFIG_EBIU_SDRRC_VAL 0x268
-#define CONFIG_EBIU_SDGCTL_VAL 0x911109
-#define CONFIG_EBIU_SDBCTL_VAL 0x37
-
-#define CONFIG_EBIU_AMGCTL_VAL 0xFF
-#define CONFIG_EBIU_AMBCTL0_VAL 0xBBC3BBC3
-#define CONFIG_EBIU_AMBCTL1_VAL 0x99B39983
-#define CF_CONFIG_EBIU_AMBCTL1_VAL 0x99B3ffc2
-
-#include <asm/blackfin-config-post.h>
+#include <configs/bfin_adi_common.h>
#endif
projects / karo-tx-uboot.git / blobdiff