at91: enable USB ethernet for taskit stamp9g20

[karo-tx-uboot.git] / include / configs / imx31_litekit.h

diff --git a/include/configs/imx31_litekit.h b/include/configs/imx31_litekit.h
index 5e976bc165699f8b5ace1803705706f96a629ef3..8428d84496ca4f3e40ddb41be0e0c67e58fad2e7 100644 (file)
--- a/include/configs/imx31_litekit.h
+++ b/include/configs/imx31_litekit.h
@@ -6,23 +6,7 @@
  *
  * Configuration settings for the LogicPD i.MX31 Litekit board.
  *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.         See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * SPDX-License-Identifier:    GPL-2.0+
  */
 
 #ifndef __CONFIG_H
@@ -33,7 +17,6 @@
  /* High Level Configuration Options */
 #define CONFIG_ARM1136         1    /* This is an arm1136 CPU core */
 #define CONFIG_MX31            1    /* in a mx31 */
-#define CONFIG_MX31_HCLK_FREQ  26000000
 #define CONFIG_MX31_CLK32      32000
 
 #define CONFIG_DISPLAY_CPUINFO
@@ -63,8 +46,8 @@
  * Hardware drivers
  */
 
-#define CONFIG_MXC_UART        1
-#define CONFIG_SYS_MX31_UART1          1
+#define CONFIG_MXC_UART
+#define CONFIG_MXC_UART_BASE   UART1_BASE
 #define CONFIG_MXC_GPIO
 
 #define CONFIG_HARD_SPI                1
@@ -72,19 +55,21 @@
 #define CONFIG_DEFAULT_SPI_BUS 1
 #define CONFIG_DEFAULT_SPI_MODE        (SPI_MODE_0 | SPI_CS_HIGH)
 
-#define CONFIG_FSL_PMIC
+/* PMIC Controller */
+#define CONFIG_POWER
+#define CONFIG_POWER_SPI
+#define CONFIG_POWER_FSL
 #define CONFIG_FSL_PMIC_BUS    1
 #define CONFIG_FSL_PMIC_CS     0
 #define CONFIG_FSL_PMIC_CLK    1000000
 #define CONFIG_FSL_PMIC_MODE   (SPI_MODE_0 | SPI_CS_HIGH)
-
-#define CONFIG_RTC_MC13783     1
+#define CONFIG_FSL_PMIC_BITLEN 32
+#define CONFIG_RTC_MC13XXX
 
 /* allow to overwrite serial and ethaddr */
 #define CONFIG_ENV_OVERWRITE
 #define CONFIG_CONS_INDEX      1
 #define CONFIG_BAUDRATE                115200
-#define CONFIG_SYS_BAUDRATE_TABLE      {9600, 19200, 38400, 57600, 115200}
 
 /***********************************************************
  * Command definition
@@ -112,7 +97,6 @@
        "prg_uboot=tftpboot 0x80000000 u-boot-imx31_litekit.bin; protect off all; erase 0xa00d0000 0xa01effff; cp.b 0x80000000 0xa00d0000 $(filesize)\0"
 
 
-#define CONFIG_NET_MULTI
 #define CONFIG_SMC911X         1
 #define CONFIG_SMC911X_BASE    (CS4_BASE + 0x00020000)
 #define CONFIG_SMC911X_32_BIT  1
@@ -133,17 +117,8 @@
 
 #define CONFIG_SYS_LOAD_ADDR           0 /* default load address */
 
-#define CONFIG_SYS_HZ                  1000
-
 #define CONFIG_CMDLINE_EDITING 1
 
-/*-----------------------------------------------------------------------
- * Stack sizes
- *
- * The stack sizes are set up in start.S using the settings below
- */
-#define CONFIG_STACKSIZE       (128 * 1024) /* regular stack */
-
 /*-----------------------------------------------------------------------
  * Physical Memory Map
  */