Enough time has passed since this board was moved to Orphan. Remove.
- Remove board/mousse/*
- Remove include/configs/MOUSSE.h
- Clean-up defined(CONFIG_MOUSSE)
- Move the entry from boards.cfg to doc/README.scrapyard
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
E: ddickey@charter.net
D: FADS Support
-N: James F. Dougherty
-E: jfd@GigabitNetworks.COM
-D: Port to the MOUSSE board
-
N: Mike Dunn
E: mikedunn@newsguy.com
D: Palmtreo680 board, docg4 nand flash driver
void
cpu_init_f (void)
{
-/* MOUSSE board is initialized in asm */
-#if !defined(CONFIG_MOUSSE)
register unsigned long val;
CONFIG_WRITE_HALFWORD(PCICR, 0x06); /* Bus Master, respond to PCI memory space acesses*/
/* CONFIG_WRITE_HALFWORD(PCISR, 0xffff); */ /*reset PCISR*/
CONFIG_READ_WORD(MCCR1, val);
CONFIG_WRITE_WORD(MCCR1, val | MCCR1_MEMGO); /* set memory access going */
__asm__ __volatile__("eieio");
-
-#endif /* !CONFIG_MOUSSE */
}
-
-#ifdef CONFIG_MOUSSE
-#ifdef INCLUDE_MPC107_REPORT
-struct MPC107_s {
- unsigned int iobase;
- char desc[120];
-} MPC107Regs[] = {
- { BMC_BASE + 0x00, "MPC107 Vendor/Device ID" },
- { BMC_BASE + 0x04, "MPC107 PCI Command/Status Register" },
- { BMC_BASE + 0x08, "MPC107 Revision" },
- { BMC_BASE + 0x0C, "MPC107 Cache Line Size" },
- { BMC_BASE + 0x10, "MPC107 LMBAR" },
- { BMC_BASE + 0x14, "MPC824x PCSR" },
- { BMC_BASE + 0xA8, "MPC824x PICR1" },
- { BMC_BASE + 0xAC, "MPC824x PICR2" },
- { BMC_BASE + 0x46, "MPC824x PACR" },
- { BMC_BASE + 0x310, "MPC824x ITWR" },
- { BMC_BASE + 0x300, "MPC824x OMBAR" },
- { BMC_BASE + 0x308, "MPC824x OTWR" },
- { BMC_BASE + 0x14, "MPC107 Peripheral Control and Status Register" },
- { BMC_BASE + 0x78, "MPC107 EUMBAR" },
- { BMC_BASE + 0xC0, "MPC107 Processor Bus Error Status" },
- { BMC_BASE + 0xC4, "MPC107 PCI Bus Error Status" },
- { BMC_BASE + 0xC8, "MPC107 Processor/PCI Error Address" },
- { BMC_BASE + 0xE0, "MPC107 AMBOR Register" },
- { BMC_BASE + 0xF0, "MPC107 MCCR1 Register" },
- { BMC_BASE + 0xF4, "MPC107 MCCR2 Register" },
- { BMC_BASE + 0xF8, "MPC107 MCCR3 Register" },
- { BMC_BASE + 0xFC, "MPC107 MCCR4 Register" },
-};
-#define N_MPC107_Regs (sizeof(MPC107Regs)/sizeof(MPC107Regs[0]))
-#endif /* INCLUDE_MPC107_REPORT */
-#endif /* CONFIG_MOUSSE */
-
/*
* initialize higher level parts of CPU like time base and timers
*/
int cpu_init_r (void)
{
-#ifdef CONFIG_MOUSSE
-#ifdef INCLUDE_MPC107_REPORT
- unsigned int tmp = 0, i;
-#endif
- /*
- * Initialize the EUMBBAR (Embedded Util Mem Block Base Addr Reg).
- * This is necessary before the EPIC, DMA ctlr, I2C ctlr, etc. can
- * be accessed.
- */
-
-#ifdef CONFIG_MPC8240 /* only on MPC8240 */
- mpc824x_mpc107_setreg (EUMBBAR, EUMBBAR_VAL);
- /* MOT/SPS: Issue #10002, PCI (FD Alias enable) */
- mpc824x_mpc107_setreg (AMBOR, 0x000000C0);
-#endif
-
-
-#ifdef INCLUDE_MPC107_REPORT
- /* Check MPC824x PCI Device and Vendor ID */
- while ((tmp = mpc824x_mpc107_getreg (BMC_BASE)) != 0x31057) {
- printf (" MPC107: offset=0x%x, val = 0x%x\n",
- BMC_BASE,
- tmp);
- }
-
- for (i = 0; i < N_MPC107_Regs; i++) {
- printf (" 0x%x/%s = 0x%x\n",
- MPC107Regs[i].iobase,
- MPC107Regs[i].desc,
- mpc824x_mpc107_getreg (MPC107Regs[i].iobase));
- }
-
- printf ("IBAT0L = 0x%08X\n", mfspr (IBAT0L));
- printf ("IBAT0U = 0x%08X\n", mfspr (IBAT0U));
- printf ("IBAT1L = 0x%08X\n", mfspr (IBAT1L));
- printf ("IBAT1U = 0x%08X\n", mfspr (IBAT1U));
- printf ("IBAT2L = 0x%08X\n", mfspr (IBAT2L));
- printf ("IBAT2U = 0x%08X\n", mfspr (IBAT2U));
- printf ("IBAT3L = 0x%08X\n", mfspr (IBAT3L));
- printf ("IBAT3U = 0x%08X\n", mfspr (IBAT3U));
- printf ("DBAT0L = 0x%08X\n", mfspr (DBAT0L));
- printf ("DBAT0U = 0x%08X\n", mfspr (DBAT0U));
- printf ("DBAT1L = 0x%08X\n", mfspr (DBAT1L));
- printf ("DBAT1U = 0x%08X\n", mfspr (DBAT1U));
- printf ("DBAT2L = 0x%08X\n", mfspr (DBAT2L));
- printf ("DBAT2U = 0x%08X\n", mfspr (DBAT2U));
- printf ("DBAT3L = 0x%08X\n", mfspr (DBAT3L));
- printf ("DBAT3U = 0x%08X\n", mfspr (DBAT3U));
-#endif /* INCLUDE_MPC107_REPORT */
-#endif /* CONFIG_MOUSSE */
return (0);
}
+++ /dev/null
-#
-# (C) Copyright 2001-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y = mousse.o m48t59y.o pci.o flash.o
+++ /dev/null
-
-U-Boot for MOUSSE/MPC8240 (KAHLUA)
-----------------------------------
-James Dougherty (jfd@broadcom.com), 09/10/01
-
-The Broadcom/Vooha Mousse board is a 3U Compact PCI system board
-which uses the MPC8240, a 64MB SDRAM SIMM, and has onboard
-DEC 21143, NS16550 UART, an SGS M48T59Y TOD, and 4MB FLASH.
-See also: http://www.vooha.com/
-
-* NVRAM setenv/printenv/savenv supported.
-* Date Command
-* Serial Console support
-* Network support
-* FLASH of kernel images is supported.
-* FLASH of U-Boot to onboard and PLCC boot region.
-* Kernel command line options from NVRAM is supported.
-* IP PNP options supported.
-
-U-Boot Loading...
-
-
-U-Boot 1.0.5 (Sep 10 2001 - 00:22:25)
-
-CPU: MPC8240 Revision 1.1 at 198 MHz: 16 kB I-Cache 16 kB D-Cache
-Board: MOUSSE MPC8240/KAHLUA - CHRP (MAP B)
-Built: Sep 10 2001 at 01:01:50
-MPLD: Revision 127
-Local Bus: 33 MHz
-RTC: M48T589 TOD/NVRAM (8176) bytes
- Current date/time: 9/10/2001 0:18:52
-DRAM: 64 MB
-FLASH: 1.960 MB
-PCI: scanning bus0 ...
- bus dev fn venID devID class rev MBAR0 MBAR1 IPIN ILINE
- 00 00 00 1057 0003 060000 11 00000008 00000000 01 00
- 00 0d 00 1011 0019 020000 41 80000001 80000000 01 01
- 00 0e 00 105a 4d38 018000 01 a0000001 a0001001 01 03
-In: serial
-Out: serial
-Err: serial
-
-Hit any key to stop autoboot: 0
-=>
-
-I. Root FileSystem/IP Configuration
-
-bootcmd=tftp 100000 vmlinux.img;bootm
-bootdelay=3
-baudrate=9600
-ipaddr=<IP ADDRESS>
-netmask=<NETMASK>
-hostname=<NAME>
-serverip=<NFS SERVER IP ADDRESS>
-ethaddr=00:00:10:20:30:44
-nfsroot=<NFS SERVER IP ADDRESS>:/boot/root-fs
-gateway=<IP ADDRESS>
-root=/dev/nfs
-stdin=serial
-stdout=serial
-stderr=serial
-
-NVRAM environment variables.
-
-use the command:
-
-setenv <attribute> <value>
-
-type "saveenv" to write to NVRAM.
-
-
-II. To boot from a hard drive:
-
-setenv root /dev/hda1
-
-
-III. IP options which configure the network:
-
-ipaddr=<IP ADDRESS OF MACHINE>
-netmask=<NETMASK>
-hostname=mousse
-ethaddr=00:00:10:20:30:44
-gateway=<IP ADDRESS OF GATEWAY/ROUTER>
-
-
-IV. IP Options which configure NFS Root/Boot Support
-
-root=/dev/nfs
-serverip=<NFS SERVER IP ADDRESS>
-nfsroot=<NFS SERVER IP ADDRESS>:/boot/root-fs
-
-V. U-Boot Image Support
-
-The U-Boot boot loader assumes that after you build
-your kernel (vmlinux), you will create a U-Boot image
-using the following commands or script:
-
-#!/bin/csh
-/bin/touch vmlinux.img
-/bin/rm vmlinux.img
-set path=($TOOLBASE/bin $path)
-set path=($U_BOOT/tools $path)
-powerpc-linux-objcopy -S -O binary vmlinux vmlinux.bin
-gzip -vf vmlinux.bin
-mkimage -A ppc -O linux -T kernel -C gzip -a 0 -e 0 -n vmlinux.bin.gz -d vmlinux.bin.gz vmlinux.img
-ls -l vmlinux.img
-
-
-VI. ONBOARD FLASH Support
-
-FLASH support is provided for the onboard FLASH chip Bootrom area.
-U-Boot is loaded into either the ROM boot region of the FLASH chip,
-after first being boot-strapped from a pre-progammed AMD29F040 PLCC
-bootrom. The PLCC needs to be programmed with a ROM burner using
-AMD 29F040 ROM parts and the u-boot.bin or u-boot.hex (S-Record)
-images.
-
-The PLCC overlays this same region of flash as the onboard FLASH,
-the jumper J100 is a chip-select for which flash chip you want to
-progam. When jumper J100 is connected to pins 2-3, you boot from
-PLCC FLASH.
-
-To bringup a system, simply flash a flash an AMD29F040 PLCC
-bootrom, and put this in the PLCC socket. Move jumper J100 to
-pins 2-3 and boot from the PLCC.
-
-
-Now, while the system is running, move Jumper J100 to
-pins 1-2 and follow the procedure below to FLASH a bootrom
-(u-boot.bin) image into the onboard bootrom region (AMD29LV160DB):
-
-tftp 100000 u-boot.bin
-protect off FFF00000 FFF7FFFF
-erase FFF00000 FFF7FFFF
-cp.b 100000 FFF00000 \${filesize}\
-
-
-Here is an example:
-
-=>tftp 100000 u-boot.bin
-eth_halt
-eth0: DC21143 Ethernet adapter(bus=0, device=13, func=0)
-DEC Ethernet iobase=0x80000000
-ARP broadcast 1
-Filename 'u-boot.bin'.
-Load address: 0x100000
-Loading: #########################
-done
-Bytes transferred = 123220 (1e154 hex)
-eth_halt
-=>protect off FFF00000 FFF7FFFF
-Un-Protected 8 sectors
-=>erase FFF00000 FFF7FFFF
-Erase Flash from 0xfff00000 to 0xfff7ffff
-Erase FLASH[PLCC_BOOT] -8 sectors:........ done
-Erased 8 sectors
-=>cp.b 100000 FFF00000 1e154
-Copy to Flash... FLASH[PLCC_BOOT]:..done
-=>
-
-
-B. FLASH RAMDISK REGION
-
-FLASH support is provided for an Onboard 512K RAMDISK region.
-
-TThe following commands will FLASH a bootrom (u-boot.bin) image
-into the onboard FLASH region (AMD29LV160DB 2MB FLASH):
-
-tftp 100000 u-boot.bin
-protect off FFF80000 FFFFFFFF
-erase FFF80000 FFFFFFFF
-cp.b 100000 FFF80000 \${filesize}\
-
-
-C. FLASH KERNEL REGION (960KB)
-
-FLASH support is provided for the 960KB onboard FLASH1 segment.
-This allows flashing of kernel images which U-Boot can load
-and run (standalone) from the onboard FLASH chip. It also assumes
-
-The following commands will FLASH a kernel image to 0xffe10000
-
-tftp 100000 vmlinux.img
-protect off FFE10000 FFEFFFFF
-erase FFE10000 FFEFFFFF
-cp.b 100000 FFE10000 \${filesize}\
-reset
-
-Here is an example:
-
-
-=>tftp 100000 vmlinux.img
-eth_halt
-eth0: DC21143 Ethernet adapter(bus=0, device=13, func=0)
-DEC Ethernet iobase=0x80000000
-ARP broadcast 1
-TFTP from server 209.128.93.133; our IP address is 209.128.93.138
-Filename 'vmlinux.img'.
-Load address: 0x100000
-Loading: #####################################################################################################################################################
-done
-Bytes transferred = 760231 (b99a7 hex)
-eth_halt
-=>protect off FFE10000 FFEFFFFF
-Un-Protected 15 sectors
-=>erase FFE10000 FFEFFFFF
-Erase Flash from 0xffe10000 to 0xffefffff
-Erase FLASH[F0_SA3(KERNEL)] -15 sectors:............... done
-Erased 15 sectors
-=>cp.b 100000 FFE10000 b99a7
-Copy to Flash... FLASH[F0_SA3(KERNEL)]:............done
-=>
-
-
-When finished, use the command:
-
-bootm ffe10000
-
-to start the kernel.
-
-Finally, to make this the default boot command, use
-the following commands:
-
-setenv bootcmd bootm ffe10000
-savenv
-
-to make it automatically boot the kernel from FLASH.
-
-
-To go back to development mode (NFS boot)
-
-setenv bootcmd tftp 100000 vmlinux.img\;bootm
-savenv
-
-
-=>tftp 100000 vmlinux.img
-eth0: DC21143 Ethernet adapter(bus=0, device=13, func=0)
-DEC Ethernet iobase=0x80000000
-ARP broadcast 1
-Filename 'vmlinux.img'.
-Load address: 0x100000
-Loading: ####################################################################################################################################################
-done
-Bytes transferred = 752717 (b7c4d hex)
-eth_halt
-=>protect off FFE10000 FFEFFFFF
-Un-Protected 15 sectors
-=>erase FFE10000 FFEFFFFF
-Erase Flash from 0xffe10000 to 0xffefffff
-Erase FLASH[F0_SA3(KERNEL)] -15 sectors:............... done
-Erased 15 sectors
-=>cp.b 100000 FFE10000 b7c4d
-Copy to Flash... FLASH[F0_SA3(KERNEL)]:............done
-=>bootm ffe10000
-## Booting image at ffe10000 ...
- Image Name: vmlinux.bin.gz
- Image Type: PowerPC Linux Kernel Image (gzip compressed)
- Data Size: 752653 Bytes = 735 kB = 0 MB
- Load Address: 00000000
- Entry Point: 00000000
- Verifying Checksum ... OK
- Uncompressing Kernel Image ... OK
-Total memory = 64MB; using 0kB for hash table (at 00000000)
-Linux version 2.4.2_hhl20 (jfd@atlantis) (gcc version 2.95.2 19991024 (release)) #597 Wed Sep 5 23:23:23 PDT 2001
-cpu0: MPC8240/KAHLUA : MOUSSE Platform : 64MB RAM: MPLD Rev. 7f
-Sandpoint port (C) 2000, 2001 MontaVista Software, Inc. (source@mvista.com)
-IP PNP: 802.3 Ethernet Address=<0:0:10:20:30:44>
-NOTICE: mounting root file system via NFS
-On node 0 totalpages: 16384
-zone(0): 16384 pages.
-zone(1): 0 pages.
-zone(2): 0 pages.
-time_init: decrementer frequency = 16.665914 MHz
-time_init: MPC8240 PCI Bus frequency = 33.331828 MHz
-Calibrating delay loop... 133.12 BogoMIPS
-Memory: 62436k available (1336k kernel code, 500k data, 88k init, 0k highmem)
-Dentry-cache hash table entries: 8192 (order: 4, 65536 bytes)
-Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
-Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
-Inode-cache hash table entries: 4096 (order: 3, 32768 bytes)
-POSIX conformance testing by UNIFIX
-PCI: Probing PCI hardware
-Linux NET4.0 for Linux 2.4
-Based upon Swansea University Computer Society NET3.039
-Initializing RT netlink socket
-Starting kswapd v1.8
-pty: 256 Unix98 ptys configured
-block: queued sectors max/low 41394kB/13798kB, 128 slots per queue
-Uniform Multi-Platform E-IDE driver Revision: 6.31
-ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
-PDC20262: IDE controller on PCI bus 00 dev 70
-PDC20262: chipset revision 1
-PDC20262: not 100% native mode: will probe irqs later
-PDC20262: ROM enabled at 0x000d0000
-PDC20262: (U)DMA Burst Bit DISABLED Primary PCI Mode Secondary PCI Mode.
-PDC20262: FORCING BURST BIT 0x00 -> 0x01 ACTIVE
-PDC20262: irq=3 dev->irq=3
- ide0: BM-DMA at 0xbfff00-0xbfff07, BIOS settings: hda:DMA, hdb:DMA
- ide1: BM-DMA at 0xbfff08-0xbfff0f, BIOS settings: hdc:pio, hdd:pio
-hda: WDC WD300AB-00BVA0, ATA DISK drive
-hdc: SONY CD-RW CRX160E, ATAPI CD/DVD-ROM drive
-ide0 at 0xbfff78-0xbfff7f,0xbfff76 on irq 3
-ide1 at 0xbfff68-0xbfff6f,0xbfff66 on irq 3
-hda: 58633344 sectors (30020 MB) w/2048KiB Cache, CHS=58168/16/63, UDMA(66)
-hdc: ATAPI 32X CD-ROM CD-R/RW drive, 4096kB Cache
-Uniform CD-ROM driver Revision: 3.12
-Partition check:
- /dev/ide/host0/bus0/target0/lun0: p1 p2
-hd: unable to get major 3 for hard disk
-udf: registering filesystem
-loop: loaded (max 8 devices)
-Serial driver version 5.02 (2000-08-09) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
-ttyS00 at 0xffe08080 (irq = 4) is a ST16650
-Linux Tulip driver version 0.9.13a (January 20, 2001)
-eth0: Digital DS21143 Tulip rev 65 at 0xbfff80, EEPROM not present, 00:00:10:20:30:44, IRQ 1.
-eth0: MII transceiver #0 config 3000 status 7829 advertising 01e1.
-NET4: Linux TCP/IP 1.0 for NET4.0
-IP Protocols: ICMP, UDP, TCP
-IP: routing cache hash table of 512 buckets, 4Kbytes
-TCP: Hash tables configured (established 4096 bind 4096)
-NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
-devfs: v0.102 (20000622) Richard Gooch (rgooch@atnf.csiro.au)
-devfs: boot_options: 0x0
-VFS: Mounted root (nfs filesystem).
-Mounted devfs on /dev
-Freeing unused kernel memory: 88k init 4k openfirmware
-eth0: Setting full-duplex based on MII#0 link partner capability of 45e1.
-INIT: version 2.78 booting
-INIT: Entering runlevel: 2
-
-
-Welcome to Linux/PPC
-MPC8240/MOUSSE
-
-
-mousse login: root
-Password:
-PAM_unix[13]: (login) session opened for user root by LOGIN(uid=0)
-Last login: Thu Sep 6 00:16:51 2001 on console
-
-
-Welcome to Linux/PPC
-MPC8240/MOUSSE
-
-
-mousse#
+++ /dev/null
-/*
- * MOUSSE/MPC8240 Board definitions.
- * Flash Routines for MOUSSE onboard AMD29LV106DB devices
- *
- * (C) Copyright 2000
- * Marius Groeger <mgroeger@sysgo.de>
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 1999, by Curt McDowell, 08-06-99, Broadcom Corp.
- * (C) Copyright 2001, James Dougherty, 07/18/01, Broadcom Corp.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc8xx.h>
-#include <malloc.h>
-#include "mousse.h"
-#include "flash.h"
-
-int flashLibDebug = 0;
-int flashLibInited = 0;
-
-#define OK 0
-#define ERROR -1
-#define STATUS int
-#define PRINTF if (flashLibDebug) printf
-#if 0
-#define PRIVATE static
-#else
-#define PRIVATE
-#endif
-
-flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS];
-
-#define SLEEP_DELAY 166
-#define FLASH_SECTOR_SIZE (64*1024)
-/***********************************************************************
- *
- * Virtual Flash Devices on Mousse board
- *
- * These must be kept in sync with the definitions in flashLib.h.
- *
- ***********************************************************************/
-
-PRIVATE flash_dev_t flashDev[] = {
- /* Bank 0 sector SA0 (16 kB) */
- { "SA0",FLASH0_BANK, FLASH0_SEG0_START, 1, 14,
- FLASH0_VENDOR_ID, FLASH0_DEVICE_ID
- },
- /* Bank 0 sector SA1 (8 kB) */
- { "SA1", FLASH0_BANK, FLASH0_SEG0_START + 0x4000, 1, 13,
- FLASH0_VENDOR_ID, FLASH0_DEVICE_ID
- },
- /* Bank 0 sector SA2 (8 kB) */
- { "SA2", FLASH0_BANK, FLASH0_SEG0_START + 0x6000, 1, 13,
- FLASH0_VENDOR_ID, FLASH0_DEVICE_ID
- },
- /* Bank 0 sector SA3 is occluded by Mousse I/O devices */
- /* Bank 0 sectors SA4-SA18, after Mousse devices up to PLCC (960 kB) */
- { "KERNEL", FLASH0_BANK, FLASH0_SEG1_START, 15, 16,
- FLASH0_VENDOR_ID, FLASH0_DEVICE_ID
- },
- /* Bank 0 sectors SA19-SA26, jumper can occlude this by PLCC (512 kB) */
- /* This is where the Kahlua boot vector and boot ROM code resides. */
- { "BOOT",FLASH0_BANK, FLASH0_SEG2_START, 8, 16,
- FLASH0_VENDOR_ID, FLASH0_DEVICE_ID
- },
- /* Bank 0 sectors SA27-SA34 (512 kB) */
- { "RAMDISK",FLASH0_BANK, FLASH0_SEG3_START, 8, 16,
- FLASH0_VENDOR_ID, FLASH0_DEVICE_ID
- },
-};
-
-int flashDevCount = (sizeof (flashDev) / sizeof (flashDev[0]));
-
-#define DEV(no) (&flashDev[no])
-#define DEV_NO(dev) ((dev) - flashDev)
-
-/***********************************************************************
- *
- * Private Flash Routines
- *
- ***********************************************************************/
-
-/*
- * The convention is:
- *
- * "addr" is always the PROM raw address, which is the address of an
- * 8-bit quantity for flash 0 and 16-bit quantity for flash 1.
- *
- * "pos" is always a logical byte position from the PROM beginning.
- */
-
-#define FLASH0_ADDR(dev, addr) \
- ((unsigned char *) ((dev)->base + (addr)))
-
-#define FLASH0_WRITE(dev, addr, value) \
- (*FLASH0_ADDR(dev, addr) = (value))
-
-#define FLASH0_READ(dev, addr) \
- (*FLASH0_ADDR(dev, addr))
-
-PRIVATE int flashCheck (flash_dev_t * dev)
-{
- if (!flashLibInited) {
- printf ("flashCheck: flashLib not initialized\n");
- return ERROR;
- }
-
- if (dev < &flashDev[0] || dev >= &flashDev[flashDevCount]) {
- printf ("flashCheck: Bad dev parameter\n");
- return ERROR;
- }
-
- if (!dev->found) {
- printf ("flashCheck: Device %d not available\n", DEV_NO (dev));
- return ERROR;
- }
-
- return OK;
-}
-
-PRIVATE void flashReset (flash_dev_t * dev)
-{
- PRINTF ("flashReset: dev=%d\n", DEV_NO (dev));
-
- if (dev->bank == FLASH0_BANK) {
- FLASH0_WRITE (dev, 0x555, 0xaa);
- FLASH0_WRITE (dev, 0xaaa, 0x55);
- FLASH0_WRITE (dev, 0x555, 0xf0);
- }
-
- udelay (SLEEP_DELAY);
-
- PRINTF ("flashReset: done\n");
-}
-
-PRIVATE int flashProbe (flash_dev_t * dev)
-{
- int rv, deviceID, vendorID;
-
- PRINTF ("flashProbe: dev=%d\n", DEV_NO (dev));
-
- if (dev->bank != FLASH0_BANK) {
- rv = ERROR;
- goto DONE;
- }
-
- FLASH0_WRITE (dev, 0xaaa, 0xaa);
- FLASH0_WRITE (dev, 0x555, 0x55);
- FLASH0_WRITE (dev, 0xaaa, 0x90);
-
- udelay (SLEEP_DELAY);
-
- vendorID = FLASH0_READ (dev, 0);
- deviceID = FLASH0_READ (dev, 2);
-
- FLASH0_WRITE (dev, 0, 0xf0);
-
- PRINTF ("flashProbe: vendor=0x%x device=0x%x\n", vendorID, deviceID);
-
- if (vendorID == dev->vendorID && deviceID == dev->deviceID)
- rv = OK;
- else
- rv = ERROR;
-
- DONE:
- PRINTF ("flashProbe: rv=%d\n", rv);
-
- return rv;
-}
-
-PRIVATE int flashWait (flash_dev_t * dev, int addr, int expect, int erase)
-{
- int rv = ERROR;
- int i, data;
- int polls;
-
-#if 0
- PRINTF ("flashWait: dev=%d addr=0x%x expect=0x%x erase=%d\n",
- DEV_NO (dev), addr, expect, erase);
-#endif
-
- if (dev->bank != FLASH0_BANK) {
- rv = ERROR;
- goto done;
- }
-
- if (erase)
- polls = FLASH_ERASE_SECTOR_TIMEOUT; /* Ticks */
- else
- polls = FLASH_PROGRAM_POLLS; /* Loops */
-
- for (i = 0; i < polls; i++) {
- if (erase)
- udelay (SLEEP_DELAY);
-
- data = FLASH0_READ (dev, addr);
-
- if (((data ^ expect) & 0x80) == 0) {
- rv = OK;
- goto done;
- }
-
- if (data & 0x20) {
- /*
- * If the 0x20 bit has come on, it could actually be because
- * the operation succeeded, so check the done bit again.
- */
-
- data = FLASH0_READ (dev, addr);
-
- if (((data ^ expect) & 0x80) == 0) {
- rv = OK;
- goto done;
- }
-
- printf ("flashWait: Program error (dev: %d, addr: 0x%x)\n",
- DEV_NO (dev), addr);
-
- flashReset (dev);
- rv = ERROR;
- goto done;
- }
- }
-
- printf ("flashWait: Timeout %s (dev: %d, addr: 0x%x)\n",
- erase ? "erasing sector" : "programming byte",
- DEV_NO (dev), addr);
-
- done:
-
-#if 0
- PRINTF ("flashWait: rv=%d\n", rv);
-#endif
-
- return rv;
-}
-
-/***********************************************************************
- *
- * Public Flash Routines
- *
- ***********************************************************************/
-
-STATUS flashLibInit (void)
-{
- int i;
-
- PRINTF ("flashLibInit: devices=%d\n", flashDevCount);
-
- for (i = 0; i < flashDevCount; i++) {
- flash_dev_t *dev = &flashDev[i];
-
- /*
- * For bank 1, probe both without and with byte swappage,
- * so that this module works on both old and new Mousse boards.
- */
-
- flashReset (dev);
-
- if (flashProbe (dev) != ERROR)
- dev->found = 1;
-
- flashReset (dev);
-
- if (flashProbe (dev) != ERROR)
- dev->found = 1;
-
- dev->swap = 0;
-
- if (dev->found) {
- PRINTF ("\n FLASH %s[%d]: iobase=0x%x - %d sectors %d KB",
- flashDev[i].name, i, flashDev[i].base,
- flashDev[i].sectors,
- (flashDev[i].sectors * FLASH_SECTOR_SIZE) / 1024);
-
- }
- }
-
- flashLibInited = 1;
-
- PRINTF ("flashLibInit: done\n");
-
- return OK;
-}
-
-STATUS flashEraseSector (flash_dev_t * dev, int sector)
-{
- int pos, addr;
-
- PRINTF ("flashErasesector: dev=%d sector=%d\n", DEV_NO (dev), sector);
-
- if (flashCheck (dev) == ERROR)
- return ERROR;
-
- if (sector < 0 || sector >= dev->sectors) {
- printf ("flashEraseSector: Sector out of range (dev: %d, sector: %d)\n", DEV_NO (dev), sector);
- return ERROR;
- }
-
- pos = FLASH_SECTOR_POS (dev, sector);
-
- if (dev->bank != FLASH0_BANK) {
- return ERROR;
- }
-
- addr = pos;
-
- FLASH0_WRITE (dev, 0xaaa, 0xaa);
- FLASH0_WRITE (dev, 0x555, 0x55);
- FLASH0_WRITE (dev, 0xaaa, 0x80);
- FLASH0_WRITE (dev, 0xaaa, 0xaa);
- FLASH0_WRITE (dev, 0x555, 0x55);
- FLASH0_WRITE (dev, addr, 0x30);
-
- return flashWait (dev, addr, 0xff, 1);
-}
-
-/*
- * Note: it takes about as long to flash all sectors together with Chip
- * Erase as it does to flash them one at a time (about 30 seconds for 2
- * MB). Also since we want to be able to treat subsets of sectors as if
- * they were complete devices, we don't use Chip Erase.
- */
-
-STATUS flashErase (flash_dev_t * dev)
-{
- int sector;
-
- PRINTF ("flashErase: dev=%d sectors=%d\n", DEV_NO (dev), dev->sectors);
-
- if (flashCheck (dev) == ERROR)
- return ERROR;
-
- for (sector = 0; sector < dev->sectors; sector++) {
- if (flashEraseSector (dev, sector) == ERROR)
- return ERROR;
- }
- return OK;
-}
-
-/*
- * Read and write bytes
- */
-
-STATUS flashRead (flash_dev_t * dev, int pos, char *buf, int len)
-{
- int addr, words;
-
- PRINTF ("flashRead: dev=%d pos=0x%x buf=0x%x len=0x%x\n",
- DEV_NO (dev), pos, (int) buf, len);
-
- if (flashCheck (dev) == ERROR)
- return ERROR;
-
- if (pos < 0 || len < 0 || pos + len > FLASH_MAX_POS (dev)) {
- printf ("flashRead: Position out of range "
- "(dev: %d, pos: 0x%x, len: 0x%x)\n",
- DEV_NO (dev), pos, len);
- return ERROR;
- }
-
- if (len == 0)
- return OK;
-
- if (dev->bank == FLASH0_BANK) {
- addr = pos;
- words = len;
-
- PRINTF ("flashRead: memcpy(0x%x, 0x%x, 0x%x)\n",
- (int) buf, (int) FLASH0_ADDR (dev, pos), len);
-
- memcpy (buf, FLASH0_ADDR (dev, addr), words);
-
- }
- PRINTF ("flashRead: rv=OK\n");
-
- return OK;
-}
-
-STATUS flashWrite (flash_dev_t * dev, int pos, char *buf, int len)
-{
- int addr, words;
-
- PRINTF ("flashWrite: dev=%d pos=0x%x buf=0x%x len=0x%x\n",
- DEV_NO (dev), pos, (int) buf, len);
-
- if (flashCheck (dev) == ERROR)
- return ERROR;
-
- if (pos < 0 || len < 0 || pos + len > FLASH_MAX_POS (dev)) {
- printf ("flashWrite: Position out of range "
- "(dev: %d, pos: 0x%x, len: 0x%x)\n",
- DEV_NO (dev), pos, len);
- return ERROR;
- }
-
- if (len == 0)
- return OK;
-
- if (dev->bank == FLASH0_BANK) {
- unsigned char tmp;
-
- addr = pos;
- words = len;
-
- while (words--) {
- tmp = *buf;
- if (~FLASH0_READ (dev, addr) & tmp) {
- printf ("flashWrite: Attempt to program 0 to 1 "
- "(dev: %d, addr: 0x%x, data: 0x%x)\n",
- DEV_NO (dev), addr, tmp);
- return ERROR;
- }
- FLASH0_WRITE (dev, 0xaaa, 0xaa);
- FLASH0_WRITE (dev, 0x555, 0x55);
- FLASH0_WRITE (dev, 0xaaa, 0xa0);
- FLASH0_WRITE (dev, addr, tmp);
- if (flashWait (dev, addr, tmp, 0) < 0)
- return ERROR;
- buf++;
- addr++;
- }
- }
-
- PRINTF ("flashWrite: rv=OK\n");
-
- return OK;
-}
-
-/*
- * flashWritable returns true if a range contains all F's.
- */
-
-STATUS flashWritable (flash_dev_t * dev, int pos, int len)
-{
- int addr, words;
- int rv = ERROR;
-
- PRINTF ("flashWritable: dev=%d pos=0x%x len=0x%x\n",
- DEV_NO (dev), pos, len);
-
- if (flashCheck (dev) == ERROR)
- goto done;
-
- if (pos < 0 || len < 0 || pos + len > FLASH_MAX_POS (dev)) {
- printf ("flashWritable: Position out of range "
- "(dev: %d, pos: 0x%x, len: 0x%x)\n",
- DEV_NO (dev), pos, len);
- goto done;
- }
-
- if (len == 0) {
- rv = 1;
- goto done;
- }
-
- if (dev->bank == FLASH0_BANK) {
- addr = pos;
- words = len;
-
- while (words--) {
- if (FLASH0_READ (dev, addr) != 0xff) {
- rv = 0;
- goto done;
- }
- addr++;
- }
- }
-
- rv = 1;
-
- done:
- PRINTF ("flashWrite: rv=%d\n", rv);
- return rv;
-}
-
-
-/*
- * NOTE: the below code cannot run from FLASH!!!
- */
-/***********************************************************************
- *
- * Flash Diagnostics
- *
- ***********************************************************************/
-
-STATUS flashDiag (flash_dev_t * dev)
-{
- unsigned int *buf = 0;
- int i, len, sector;
- int rv = ERROR;
-
- if (flashCheck (dev) == ERROR)
- return ERROR;
-
- printf ("flashDiag: Testing device %d, "
- "base: 0x%x, %d sectors @ %d kB = %d kB\n",
- DEV_NO (dev), dev->base,
- dev->sectors,
- 1 << (dev->lgSectorSize - 10),
- dev->sectors << (dev->lgSectorSize - 10));
-
- len = 1 << dev->lgSectorSize;
-
- printf ("flashDiag: Erasing\n");
-
- if (flashErase (dev) == ERROR) {
- printf ("flashDiag: Erase failed\n");
- goto done;
- }
- printf ("%d bytes requested ...\n", len);
- buf = malloc (len);
- printf ("allocated %d bytes ...\n", len);
- if (buf == 0) {
- printf ("flashDiag: Out of memory\n");
- goto done;
- }
-
- /*
- * Write unique counting pattern to each sector
- */
-
- for (sector = 0; sector < dev->sectors; sector++) {
- printf ("flashDiag: Write sector %d\n", sector);
-
- for (i = 0; i < len / 4; i++)
- buf[i] = sector << 24 | i;
-
- if (flashWrite (dev,
- sector << dev->lgSectorSize,
- (char *) buf, len) == ERROR) {
- printf ("flashDiag: Write failed (dev: %d, sector: %d)\n",
- DEV_NO (dev), sector);
- goto done;
- }
- }
-
- /*
- * Verify
- */
-
- for (sector = 0; sector < dev->sectors; sector++) {
- printf ("flashDiag: Verify sector %d\n", sector);
-
- if (flashRead (dev,
- sector << dev->lgSectorSize,
- (char *) buf, len) == ERROR) {
- printf ("flashDiag: Read failed (dev: %d, sector: %d)\n",
- DEV_NO (dev), sector);
- goto done;
- }
-
- for (i = 0; i < len / 4; i++) {
- if (buf[i] != (sector << 24 | i)) {
- printf ("flashDiag: Verify error "
- "(dev: %d, sector: %d, offset: 0x%x)\n",
- DEV_NO (dev), sector, i);
- printf ("flashDiag: Expected 0x%08x, got 0x%08x\n",
- sector << 24 | i, buf[i]);
-
- goto done;
- }
- }
- }
-
- printf ("flashDiag: Erasing\n");
-
- if (flashErase (dev) == ERROR) {
- printf ("flashDiag: Final erase failed\n");
- goto done;
- }
-
- rv = OK;
-
- done:
- if (buf)
- free (buf);
-
- if (rv == OK)
- printf ("flashDiag: Device %d passed\n", DEV_NO (dev));
- else
- printf ("flashDiag: Device %d failed\n", DEV_NO (dev));
-
- return rv;
-}
-
-STATUS flashDiagAll (void)
-{
- int i;
- int rv = OK;
-
- PRINTF ("flashDiagAll: devices=%d\n", flashDevCount);
-
- for (i = 0; i < flashDevCount; i++) {
- flash_dev_t *dev = &flashDev[i];
-
- if (dev->found && flashDiag (dev) == ERROR)
- rv = ERROR;
- }
-
- if (rv == OK)
- printf ("flashDiagAll: Passed\n");
- else
- printf ("flashDiagAll: Failed because of earlier errors\n");
-
- return OK;
-}
-
-
-/*-----------------------------------------------------------------------
- */
-unsigned long flash_init (void)
-{
- unsigned long size = 0;
- flash_dev_t *dev = NULL;
-
- flashLibInit ();
-
- /*
- * Provide info for FLASH (up to 960K) of Kernel Image data.
- */
- dev = FLASH_DEV_BANK0_LOW;
- flash_info[FLASH_BANK_KERNEL].flash_id =
- (dev->vendorID << 16) | dev->deviceID;
- flash_info[FLASH_BANK_KERNEL].sector_count = dev->sectors;
- flash_info[FLASH_BANK_KERNEL].size =
- flash_info[FLASH_BANK_KERNEL].sector_count * FLASH_SECTOR_SIZE;
- flash_info[FLASH_BANK_KERNEL].start[FIRST_SECTOR] = dev->base;
- size += flash_info[FLASH_BANK_KERNEL].size;
-
- /*
- * Provide info for 512K PLCC FLASH ROM (U-Boot)
- */
- dev = FLASH_DEV_BANK0_BOOT;
- flash_info[FLASH_BANK_BOOT].flash_id =
- (dev->vendorID << 16) | dev->deviceID;
- flash_info[FLASH_BANK_BOOT].sector_count = dev->sectors;
- flash_info[FLASH_BANK_BOOT].size =
- flash_info[FLASH_BANK_BOOT].sector_count * FLASH_SECTOR_SIZE;
- flash_info[FLASH_BANK_BOOT].start[FIRST_SECTOR] = dev->base;
- size += flash_info[FLASH_BANK_BOOT].size;
-
-
- /*
- * Provide info for 512K FLASH0 segment (U-Boot)
- */
- dev = FLASH_DEV_BANK0_HIGH;
- flash_info[FLASH_BANK_AUX].flash_id =
- (dev->vendorID << 16) | dev->deviceID;
- flash_info[FLASH_BANK_AUX].sector_count = dev->sectors;
- flash_info[FLASH_BANK_AUX].size =
- flash_info[FLASH_BANK_AUX].sector_count * FLASH_SECTOR_SIZE;
- flash_info[FLASH_BANK_AUX].start[FIRST_SECTOR] = dev->base;
- size += flash_info[FLASH_BANK_AUX].size;
-
-
- return size;
-}
-
-/*
- * Get flash device from U-Boot flash info.
- */
-flash_dev_t *getFlashDevFromInfo (flash_info_t * info)
-{
- int i;
-
- if (!info)
- return NULL;
-
- for (i = 0; i < flashDevCount; i++) {
- flash_dev_t *dev = &flashDev[i];
-
- if (dev->found && (dev->base == info->start[0]))
- return dev;
- }
- printf ("ERROR: notice, no FLASH mapped at address 0x%x\n",
- (unsigned int) info->start[0]);
- return NULL;
-}
-
-ulong flash_get_size (vu_long * addr, flash_info_t * info)
-{
- int i;
-
- for (i = 0; i < flashDevCount; i++) {
- flash_dev_t *dev = &flashDev[i];
-
- if (dev->found) {
- if (dev->base == (unsigned int) addr) {
- info->flash_id = (dev->vendorID << 16) | dev->deviceID;
- info->sector_count = dev->sectors;
- info->size = info->sector_count * FLASH_SECTOR_SIZE;
- return dev->sectors * FLASH_SECTOR_SIZE;
- }
- }
- }
- return 0;
-}
-
-void flash_print_info (flash_info_t * info)
-{
- int i;
- unsigned int chip;
-
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("missing or unknown FLASH type\n");
- return;
- }
-
- switch ((info->flash_id >> 16) & 0xff) {
- case 0x1:
- printf ("AMD ");
- break;
- default:
- printf ("Unknown Vendor ");
- break;
- }
- chip = (unsigned int) info->flash_id & 0x000000ff;
-
- switch (chip) {
-
- case AMD_ID_F040B:
- printf ("AM29F040B (4 Mbit)\n");
- break;
-
- case AMD_ID_LV160B:
- case FLASH_AM160LV:
- case 0x49:
- printf ("AM29LV160B (16 Mbit / 2M x 8bit)\n");
- break;
-
- default:
- printf ("Unknown Chip Type:0x%x\n", chip);
- break;
- }
-
- printf (" Size: %ld bytes in %d Sectors\n",
- info->size, info->sector_count);
-
- printf (" Sector Start Addresses:");
- for (i = 0; i < info->sector_count; ++i) {
- if ((i % 5) == 0)
- printf ("\n ");
- printf (" %08lX%s",
- info->start[FIRST_SECTOR] + i * FLASH_SECTOR_SIZE,
- info->protect[i] ? " (RO)" : " ");
- }
- printf ("\n");
-}
-
-
-/*
- * Erase a range of flash sectors.
- */
-int flash_erase (flash_info_t * info, int s_first, int s_last)
-{
- int prot, sect;
- flash_dev_t *dev = NULL;
-
- if ((s_first < 0) || (s_first > s_last)) {
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("- missing\n");
- } else {
- printf ("- no sectors to erase\n");
- }
- return 1;
- }
-
- prot = 0;
- for (sect = s_first; sect <= s_last; sect++) {
- if (info->protect[sect]) {
- prot++;
- }
- }
-
- if (prot) {
- printf ("- Warning: %d protected sectors will not be erased!\n",
- prot);
- } else {
- printf ("\n");
- }
-
- /* Start erase on unprotected sectors */
- dev = getFlashDevFromInfo (info);
- if (dev) {
- printf ("Erase FLASH[%s] -%d sectors:", dev->name, dev->sectors);
- for (sect = s_first; sect <= s_last; sect++) {
- if (info->protect[sect] == 0) { /* not protected */
- printf (".");
- if (ERROR == flashEraseSector (dev, sect)) {
- printf ("ERROR: could not erase sector %d on FLASH[%s]\n", sect, dev->name);
- return 1;
- }
- }
- }
- }
- printf (" done\n");
- return 0;
-}
-
-/*-----------------------------------------------------------------------
- * Write a word to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_word (flash_info_t * info, ulong dest, ulong data)
-{
-
- flash_dev_t *dev = getFlashDevFromInfo (info);
- int addr = dest - info->start[0];
-
- if (!dev)
- return 1;
-
- if (OK != flashWrite (dev, addr, (char *) &data, sizeof (ulong))) {
- printf ("ERROR: could not write to addr=0x%x, data=0x%x\n",
- (unsigned int) addr, (unsigned) data);
- return 1;
- }
-
- if ((addr % FLASH_SECTOR_SIZE) == 0)
- printf (".");
-
-
- PRINTF ("write_word:0x%x, base=0x%x, addr=0x%x, data=0x%x\n",
- (unsigned) info->start[0],
- (unsigned) dest,
- (unsigned) (dest - info->start[0]), (unsigned) data);
-
- return (0);
-}
-
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-
-int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt)
-{
- ulong cp, wp, data;
- int i, l, rc;
- flash_dev_t *dev = getFlashDevFromInfo (info);
-
- if (dev) {
- printf ("FLASH[%s]:", dev->name);
- wp = (addr & ~3); /* get lower word aligned address */
-
- /*
- * handle unaligned start bytes
- */
- if ((l = addr - wp) != 0) {
- data = 0;
- for (i = 0, cp = wp; i < l; ++i, ++cp) {
- data = (data << 8) | (*(uchar *) cp);
- }
- for (; i < 4 && cnt > 0; ++i) {
- data = (data << 8) | *src++;
- --cnt;
- ++cp;
- }
- for (; cnt == 0 && i < 4; ++i, ++cp) {
- data = (data << 8) | (*(uchar *) cp);
- }
- if ((rc = write_word (info, wp, data)) != 0) {
- return (rc);
- }
- wp += 4;
- }
-
- /*
- * handle word aligned part
- */
- while (cnt >= 4) {
- data = 0;
- for (i = 0; i < 4; ++i) {
- data = (data << 8) | *src++;
- }
- if ((rc = write_word (info, wp, data)) != 0) {
- return (rc);
- }
- wp += 4;
- cnt -= 4;
- }
-
- if (cnt == 0) {
- return (0);
- }
-
- /*
- * handle unaligned tail bytes
- */
- data = 0;
- for (i = 0, cp = wp; i < 4 && cnt > 0; ++i, ++cp) {
- data = (data << 8) | *src++;
- --cnt;
- }
- for (; i < 4; ++i, ++cp) {
- data = (data << 8) | (*(uchar *) cp);
- }
-
- return (write_word (info, wp, data));
- }
- return 1;
-}
-
-/*-----------------------------------------------------------------------
- */
+++ /dev/null
-#ifndef FLASH_LIB_H
-#define FLASH_LIB_H
-
-#include <common.h>
-
-/* PIO operations max */
-#define FLASH_PROGRAM_POLLS 100000
-
-/* 10 Seconds default */
-#define FLASH_ERASE_SECTOR_TIMEOUT (10*1000 /*SEC*/ )
-
-/* Flash device info structure */
-typedef struct flash_dev_s {
- char name[24]; /* Bank Name */
- int bank; /* Bank 0 or 1 */
- unsigned int base; /* Base address */
- int sectors; /* Sector count */
- int lgSectorSize; /* Log2(usable bytes/sector) */
- int vendorID; /* Expected vendor ID */
- int deviceID; /* Expected device ID */
- int found; /* Set if found by flashLibInit */
- int swap; /* Set for bank 1 if byte swap req'd */
-} flash_dev_t;
-
-#define FLASH_MAX_POS(dev) \
- ((dev)->sectors << (dev)->lgSectorSize)
-
-#define FLASH_SECTOR_POS(dev, sector) \
- ((sector) << (dev)->lgSectorSize)
-
-/* AMD 29F040 */
-#define FLASH0_BANK 0
-#define FLASH0_VENDOR_ID 0x01
-#define FLASH0_DEVICE_ID 0x49
-
-/* AMD29LV160DB */
-#define FLASH1_BANK 1
-#define FLASH1_VENDOR_ID 0x0001
-#define FLASH1_DEVICE_ID 0x2249
-
-extern flash_dev_t flashDev[];
-extern int flashDevCount;
-
-/*
- * Device pointers
- *
- * These must be kept in sync with the table in flashLib.c.
- */
-#define FLASH_DEV_BANK0_SA0 (&flashDev[0])
-#define FLASH_DEV_BANK0_SA1 (&flashDev[1])
-#define FLASH_DEV_BANK0_SA2 (&flashDev[2])
-#define FLASH_DEV_BANK0_LOW (&flashDev[3]) /* 960K */
-#define FLASH_DEV_BANK0_BOOT (&flashDev[4]) /* PLCC */
-#define FLASH_DEV_BANK0_HIGH (&flashDev[5]) /* 512K PLCC shadow */
-
-unsigned long flash_init(void);
-int flashEraseSector(flash_dev_t *dev, int sector);
-int flashErase(flash_dev_t *dev);
-int flashRead(flash_dev_t *dev, int pos, char *buf, int len);
-int flashWrite(flash_dev_t *dev, int pos, char *buf, int len);
-int flashWritable(flash_dev_t *dev, int pos, int len);
-int flashDiag(flash_dev_t *dev);
-int flashDiagAll(void);
-
-ulong flash_get_size (vu_long *addr, flash_info_t *info);
-void flash_print_info (flash_info_t *info);
-int flash_erase (flash_info_t *info, int s_first, int s_last);
-int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt);
-
-/*
- * Flash info indices.
- */
-#define FLASH_BANK_KERNEL 0
-#define FLASH_BANK_BOOT 1
-#define FLASH_BANK_AUX 2
-#define FIRST_SECTOR 0
-
-#endif /* !FLASH_LIB_H */
+++ /dev/null
-/*
- * SGS M48-T59Y TOD/NVRAM Driver
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 1999, by Curt McDowell, 08-06-99, Broadcom Corp.
- *
- * (C) Copyright 2001, James Dougherty, 07/18/01, Broadcom Corp.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * SGS M48-T59Y TOD/NVRAM Driver
- *
- * The SGS M48 an 8K NVRAM starting at offset M48_BASE_ADDR and
- * continuing for 8176 bytes. After that starts the Time-Of-Day (TOD)
- * registers which are used to set/get the internal date/time functions.
- *
- * This module implements Y2K compliance by taking full year numbers
- * and translating back and forth from the TOD 2-digit year.
- *
- * NOTE: for proper interaction with an operating system, the TOD should
- * be used to store Universal Coordinated Time (GMT) and timezone
- * conversions should be used.
- *
- * Here is a diagram of the memory layout:
- *
- * +---------------------------------------------+ 0xffe0a000
- * | Non-volatile memory | .
- * | | .
- * | (8176 bytes of Non-volatile memory) | .
- * | | .
- * +---------------------------------------------+ 0xffe0bff0
- * | Flags |
- * +---------------------------------------------+ 0xffe0bff1
- * | Unused |
- * +---------------------------------------------+ 0xffe0bff2
- * | Alarm Seconds |
- * +---------------------------------------------+ 0xffe0bff3
- * | Alarm Minutes |
- * +---------------------------------------------+ 0xffe0bff4
- * | Alarm Date |
- * +---------------------------------------------+ 0xffe0bff5
- * | Interrupts |
- * +---------------------------------------------+ 0xffe0bff6
- * | WatchDog |
- * +---------------------------------------------+ 0xffe0bff7
- * | Calibration |
- * +---------------------------------------------+ 0xffe0bff8
- * | Seconds |
- * +---------------------------------------------+ 0xffe0bff9
- * | Minutes |
- * +---------------------------------------------+ 0xffe0bffa
- * | Hours |
- * +---------------------------------------------+ 0xffe0bffb
- * | Day |
- * +---------------------------------------------+ 0xffe0bffc
- * | Date |
- * +---------------------------------------------+ 0xffe0bffd
- * | Month |
- * +---------------------------------------------+ 0xffe0bffe
- * | Year (2 digits only) |
- * +---------------------------------------------+ 0xffe0bfff
- */
-#include <common.h>
-#include <rtc.h>
-#include "mousse.h"
-
-/*
- * Imported from mousse.h:
- *
- * TOD_REG_BASE Base of m48t59y TOD registers
- * SYS_TOD_UNPROTECT() Disable NVRAM write protect
- * SYS_TOD_PROTECT() Re-enable NVRAM write protect
- */
-
-#define YEAR 0xf
-#define MONTH 0xe
-#define DAY 0xd
-#define DAY_OF_WEEK 0xc
-#define HOUR 0xb
-#define MINUTE 0xa
-#define SECOND 0x9
-#define CONTROL 0x8
-#define WATCH 0x7
-#define INTCTL 0x6
-#define WD_DATE 0x5
-#define WD_HOUR 0x4
-#define WD_MIN 0x3
-#define WD_SEC 0x2
-#define _UNUSED 0x1
-#define FLAGS 0x0
-
-#define M48_ADDR ((volatile unsigned char *) TOD_REG_BASE)
-
-int m48_tod_init(void)
-{
- SYS_TOD_UNPROTECT();
-
- M48_ADDR[CONTROL] = 0;
- M48_ADDR[WATCH] = 0;
- M48_ADDR[INTCTL] = 0;
-
- /*
- * If the oscillator is currently stopped (as on a new part shipped
- * from the factory), start it running.
- *
- * Here is an example of the TOD bytes on a brand new M48T59Y part:
- * 00 00 00 00 00 00 00 00 00 88 8c c3 bf c8 f5 01
- */
-
- if (M48_ADDR[SECOND] & 0x80)
- M48_ADDR[SECOND] = 0;
-
- /* Is battery low */
- if ( M48_ADDR[FLAGS] & 0x10) {
- printf("NOTICE: Battery low on Real-Time Clock (replace SNAPHAT).\n");
- }
-
- SYS_TOD_PROTECT();
-
- return 0;
-}
-
-/*
- * m48_tod_set
- */
-
-static int to_bcd(int value)
-{
- return value / 10 * 16 + value % 10;
-}
-
-static int from_bcd(int value)
-{
- return value / 16 * 10 + value % 16;
-}
-
-static int day_of_week(int y, int m, int d) /* 0-6 ==> Sun-Sat */
-{
- static int t[] = {0, 3, 2, 5, 0, 3, 5, 1, 4, 6, 2, 4};
- y -= m < 3;
- return (y + y/4 - y/100 + y/400 + t[m-1] + d) % 7;
-}
-
-/*
- * Note: the TOD should store the current GMT
- */
-
-int m48_tod_set(int year, /* 1980-2079 */
- int month, /* 01-12 */
- int day, /* 01-31 */
- int hour, /* 00-23 */
- int minute, /* 00-59 */
- int second) /* 00-59 */
-
-{
- SYS_TOD_UNPROTECT();
-
- M48_ADDR[CONTROL] |= 0x80; /* Set WRITE bit */
-
- M48_ADDR[YEAR] = to_bcd(year % 100);
- M48_ADDR[MONTH] = to_bcd(month);
- M48_ADDR[DAY] = to_bcd(day);
- M48_ADDR[DAY_OF_WEEK] = day_of_week(year, month, day) + 1;
- M48_ADDR[HOUR] = to_bcd(hour);
- M48_ADDR[MINUTE] = to_bcd(minute);
- M48_ADDR[SECOND] = to_bcd(second);
-
- M48_ADDR[CONTROL] &= ~0x80; /* Clear WRITE bit */
-
- SYS_TOD_PROTECT();
-
- return 0;
-}
-
-/*
- * Note: the TOD should store the current GMT
- */
-
-int m48_tod_get(int *year, /* 1980-2079 */
- int *month, /* 01-12 */
- int *day, /* 01-31 */
- int *hour, /* 00-23 */
- int *minute, /* 00-59 */
- int *second) /* 00-59 */
-{
- int y;
-
- SYS_TOD_UNPROTECT();
-
- M48_ADDR[CONTROL] |= 0x40; /* Set READ bit */
-
- y = from_bcd(M48_ADDR[YEAR]);
- *year = y < 80 ? 2000 + y : 1900 + y;
- *month = from_bcd(M48_ADDR[MONTH]);
- *day = from_bcd(M48_ADDR[DAY]);
- /* day_of_week = M48_ADDR[DAY_OF_WEEK] & 0xf; */
- *hour = from_bcd(M48_ADDR[HOUR]);
- *minute = from_bcd(M48_ADDR[MINUTE]);
- *second = from_bcd(M48_ADDR[SECOND] & 0x7f);
-
- M48_ADDR[CONTROL] &= ~0x40; /* Clear READ bit */
-
- SYS_TOD_PROTECT();
-
- return 0;
-}
-
-int m48_tod_get_second(void)
-{
- return from_bcd(M48_ADDR[SECOND] & 0x7f);
-}
-
-/*
- * Watchdog function
- *
- * If usec is 0, the watchdog timer is disarmed.
- *
- * If usec is non-zero, the watchdog timer is armed (or re-armed) for
- * approximately usec microseconds (if the exact requested usec is
- * not supported by the chip, the next higher available value is used).
- *
- * Minimum watchdog timeout = 62500 usec
- * Maximum watchdog timeout = 124 sec (124000000 usec)
- */
-
-void m48_watchdog_arm(int usec)
-{
- int mpy, res;
-
- SYS_TOD_UNPROTECT();
-
- if (usec == 0) {
- res = 0;
- mpy = 0;
- } else if (usec < 2000000) { /* Resolution: 1/16s if below 2s */
- res = 0;
- mpy = (usec + 62499) / 62500;
- } else if (usec < 8000000) { /* Resolution: 1/4s if below 8s */
- res = 1;
- mpy = (usec + 249999) / 250000;
- } else if (usec < 32000000) { /* Resolution: 1s if below 32s */
- res = 2;
- mpy = (usec + 999999) / 1000000;
- } else { /* Resolution: 4s up to 124s */
- res = 3;
- mpy = (usec + 3999999) / 4000000;
- if (mpy > 31)
- mpy = 31;
- }
-
- M48_ADDR[WATCH] = (0x80 | /* Steer to RST signal (IRQ = N/C) */
- mpy << 2 |
- res);
-
- SYS_TOD_PROTECT();
-}
-
-/*
- * U-Boot RTC support.
- */
-int
-rtc_get( struct rtc_time *tmp )
-{
- m48_tod_get(&tmp->tm_year,
- &tmp->tm_mon,
- &tmp->tm_mday,
- &tmp->tm_hour,
- &tmp->tm_min,
- &tmp->tm_sec);
- tmp->tm_yday = 0;
- tmp->tm_isdst= 0;
-
-#ifdef RTC_DEBUG
- printf( "Get DATE: %4d-%02d-%02d (wday=%d) TIME: %2d:%02d:%02d\n",
- tmp->tm_year, tmp->tm_mon, tmp->tm_mday, tmp->tm_wday,
- tmp->tm_hour, tmp->tm_min, tmp->tm_sec );
-#endif
-
- return 0;
-}
-
-int rtc_set( struct rtc_time *tmp )
-{
- m48_tod_set(tmp->tm_year, /* 1980-2079 */
- tmp->tm_mon, /* 01-12 */
- tmp->tm_mday, /* 01-31 */
- tmp->tm_hour, /* 00-23 */
- tmp->tm_min, /* 00-59 */
- tmp->tm_sec); /* 00-59 */
-
-#ifdef RTC_DEBUG
- printf( "Set DATE: %4d-%02d-%02d (wday=%d) TIME: %2d:%02d:%02d\n",
- tmp->tm_year, tmp->tm_mon, tmp->tm_mday, tmp->tm_wday,
- tmp->tm_hour, tmp->tm_min, tmp->tm_sec);
-#endif
-
- return 0;
-}
-
-void
-rtc_reset (void)
-{
- m48_tod_init();
-}
+++ /dev/null
-/*
- * SGS M48-T59Y TOD/NVRAM Driver
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 1999, by Curt McDowell, 08-06-99, Broadcom Corp.
- *
- * (C) Copyright 2001, James Dougherty, 07/18/01, Broadcom Corp.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __M48_T59_Y_H
-#define __M48_T59_Y_H
-
-/*
- * M48 T59Y -Timekeeping Battery backed SRAM.
- */
-
-int m48_tod_init(void);
-
-int m48_tod_set(int year,
- int month,
- int day,
- int hour,
- int minute,
- int second);
-
-int m48_tod_get(int *year,
- int *month,
- int *day,
- int *hour,
- int *minute,
- int *second);
-
-int m48_tod_get_second(void);
-
-void m48_watchdog_arm(int usec);
-
-#endif /*!__M48_T59_Y_H */
+++ /dev/null
-/*
- * MOUSSE Board Support
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2001
- * James Dougherty, jfd@cs.stanford.edu
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc824x.h>
-#include <netdev.h>
-#include <asm/processor.h>
-#include <timestamp.h>
-
-#include "mousse.h"
-#include "m48t59y.h"
-#include <pci.h>
-
-
-int checkboard (void)
-{
- ulong busfreq = get_bus_freq (0);
- char buf[32];
-
- puts ("Board: MOUSSE MPC8240/KAHLUA - CHRP (MAP B)\n");
- printf ("Built: %s at %s\n", U_BOOT_DATE, U_BOOT_TIME);
- printf ("MPLD: Revision %d\n", SYS_REVID_GET ());
- printf ("Local Bus: %s MHz\n", strmhz (buf, busfreq));
-
- return 0;
-}
-
-int checkflash (void)
-{
- printf ("checkflash\n");
- flash_init ();
- return 0;
-}
-
-phys_size_t initdram (int board_type)
-{
- return CONFIG_SYS_RAM_SIZE;
-}
-
-
-void get_tod (void)
-{
- int year, month, day, hour, minute, second;
-
- m48_tod_get (&year, &month, &day, &hour, &minute, &second);
-
- printf (" Current date/time: %d/%d/%d %d:%d:%d \n",
- month, day, year, hour, minute, second);
-
-}
-
-/*
- * EPIC, PCI, and I/O devices.
- * Initialize Mousse Platform, probe for PCI devices,
- * Query configuration parameters if not set.
- */
-int misc_init_f (void)
-{
- m48_tod_init (); /* Init SGS M48T59Y TOD/NVRAM */
- printf ("RTC: M48T589 TOD/NVRAM (%d) bytes\n", TOD_NVRAM_SIZE);
- get_tod ();
- return 0;
-}
-
-int board_eth_init(bd_t *bis)
-{
- return pci_eth_init(bis);
-}
+++ /dev/null
-/*
- * MOUSSE/MPC8240 Board definitions.
- * For more info, see http://www.vooha.com/
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2001
- * James Dougherty (jfd@cs.stanford.edu)
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __MOUSSE_H
-#define __MOUSSE_H
-
-/* System addresses */
-
-#define PCI_SPECIAL_BASE 0xfe000000
-#define PCI_SPECIAL_SIZE 0x01000000
-
-/* PORTX Device Addresses for Mousse */
-
-#define PORTX_DEV_BASE 0xff000000
-#define PORTX_DEV_SIZE 0x01000000
-
-#define ENET_DEV_BASE 0x80000000
-
-#define PLD_REG_BASE (PORTX_DEV_BASE | 0xe09000)
-#define PLD_REG(off) (*(volatile unsigned char *) \
- (PLD_REG_BASE + (off)))
-
-#define PLD_REVID_B1 0x7f
-#define PLD_REVID_B2 0x01
-
-/* MPLD */
-#define SYS_HARD_RESET() { for (;;) PLD_REG(0) = 0; } /* clr 0x80 bit */
-#define SYS_REVID_GET() ((int) PLD_REG(0) & 0x7f)
-#define SYS_LED_OFF() (PLD_REG(1) |= 0x80)
-#define SYS_LED_ON() (PLD_REG(1) &= ~0x80)
-#define SYS_WATCHDOG_IRQ3() (PLD_REG(2) |= 0x80)
-#define SYS_WATCHDOG_RESET() (PLD_REG(2) &= ~0x80)
-#define SYS_TOD_PROTECT() (PLD_REG(3) |= 0x80)
-#define SYS_TOD_UNPROTECT() (PLD_REG(3) &= ~0x80)
-
-/* SGS M48T59Y */
-#define TOD_BASE (PORTX_DEV_BASE | 0xe0a000)
-#define TOD_REG_BASE (TOD_BASE | 0x1ff0)
-#define TOD_NVRAM_BASE TOD_BASE
-#define TOD_NVRAM_SIZE 0x1ff0
-#define TOD_NVRAM_LIMIT (TOD_NVRAM_BASE + TOD_NVRAM_SIZE)
-
-/* NS16552 SIO */
-#define SERIAL_BASE(_x) (PORTX_DEV_BASE | 0xe08000 | ((_x) ? 0 : 0x80))
-#define N_SIO_CHANNELS 2
-#define N_COM_PORTS N_SIO_CHANNELS
-
-/*
- * On-board Dec21143 PCI Ethernet
- * Note: The PCI MBAR chosen here was used from MPC8240UM which states
- * that PCI memory is at: 0x80000 - 0xFDFFFFFF, if AMBOR[CPU_FD_ALIAS]
- * is set, then PCI memory maps 1-1 with this address range in the
- * correct byte order.
- */
-#define PCI_ENET_IOADDR 0x80000000
-#define PCI_ENET_MEMADDR 0x80000000
-
-/*
- * Flash Memory Layout
- *
- * 2 MB Flash Bank 0 runs in 8-bit mode. In Flash Bank 0, the 32 kB
- * sector SA3 is obscured by the 32 kB serial/TOD access space, and
- * the 64 kB sectors SA19-SA26 are obscured by the 512 kB PLCC
- * containing the fixed boot ROM. (If the 512 kB PLCC is
- * deconfigured by jumper, this window to Flash Bank 0 becomes
- * visible, but it still contains the fixed boot code and should be
- * considered read-only). Flash Bank 0 sectors SA0 (16 kB), SA1 (8
- * kB), and SA2 (8 kB) are currently unused.
- *
- * 2 MB Flash Bank 1 runs in 16-bit mode. Flash Bank 1 is fully
- * usable, but it's a 16-bit wide device on a 64-bit bus. Therefore
- * 16-bit words only exist at addresses that are multiples of 8. All
- * PROM data and control addresses must be multiplied by 8.
- *
- * See flashMap.c for description of flash filesystem layout.
- */
-
-/*
- * FLASH memory address space: 8-bit wide FLASH memory spaces.
- */
-#define FLASH0_SEG0_START 0xffe00000 /* Baby 32Kb segment */
-#define FLASH0_SEG0_END 0xffe07fff /* 16 kB + 8 kB + 8 kB */
-#define FLASH0_SEG0_SIZE 0x00008000 /* (sectors SA0-SA2) */
-
-#define FLASH0_SEG1_START 0xffe10000 /* 1MB - 64Kb FLASH0 seg */
-#define FLASH0_SEG1_END 0xffefffff /* 960 kB */
-#define FLASH0_SEG1_SIZE 0x000f0000
-
-#define FLASH0_SEG2_START 0xfff00000 /* Boot Loader stored here */
-#define FLASH0_SEG2_END 0xfff7ffff /* 512 kB FLASH0/PLCC seg */
-#define FLASH0_SEG2_SIZE 0x00080000
-
-#define FLASH0_SEG3_START 0xfff80000 /* 512 kB FLASH0 seg */
-#define FLASH0_SEG3_END 0xffffffff
-#define FLASH0_SEG3_SIZE 0x00080000
-
-/* Where Kahlua starts */
-#define FLASH_RESET_VECT 0xfff00100
-
-/*
- * CHRP / PREP (MAP A/B) definitions.
- */
-
-#define PREP_REG_ADDR 0x80000cf8 /* MPC107 Config, Map A */
-#define PREP_REG_DATA 0x80000cfc /* MPC107 Config, Map A */
-/* MPC107 (MPC8240 internal EUMBBAR mapped) */
-#define CHRP_REG_ADDR 0xfec00000 /* MPC106 Config, Map B */
-#define CHRP_REG_DATA 0xfee00000 /* MPC106 Config, Map B */
-
-/*
- * Mousse PCI IDSEL Assignments (Device Number)
- */
-#define MOUSSE_IDSEL_ENET 13 /* On-board 21143 Ethernet */
-#define MOUSSE_IDSEL_LPCI 14 /* On-board PCI slot */
-#define MOUSSE_IDSEL_82371 15 /* That other thing */
-#define MOUSSE_IDSEL_CPCI2 31 /* CPCI slot 2 */
-#define MOUSSE_IDSEL_CPCI3 30 /* CPCI slot 3 */
-#define MOUSSE_IDSEL_CPCI4 29 /* CPCI slot 4 */
-#define MOUSSE_IDSEL_CPCI5 28 /* CPCI slot 5 */
-#define MOUSSE_IDSEL_CPCI6 27 /* CPCI slot 6 */
-
-/*
- * Mousse Interrupt Mapping:
- *
- * IRQ1 Enet (intA|intB|intC|intD)
- * IRQ2 CPCI intA (See below)
- * IRQ3 Local PCI slot intA|intB|intC|intD
- * IRQ4 COM1 Serial port (Actually higher addressed port on duart)
- *
- * PCI Interrupt Mapping in CPCI chassis:
- *
- * | CPCI Slot
- * | 1 (CPU) 2 3 4 5 6
- * -----------+--------+-------+-------+-------+-------+-------+
- * intA | X X X
- * intB | X X X
- * intC | X X X
- * intD | X X X
- */
-
-
-#define EPIC_VECTOR_EXT0 0
-#define EPIC_VECTOR_EXT1 1
-#define EPIC_VECTOR_EXT2 2
-#define EPIC_VECTOR_EXT3 3
-#define EPIC_VECTOR_EXT4 4
-#define EPIC_VECTOR_TM0 16
-#define EPIC_VECTOR_TM1 17
-#define EPIC_VECTOR_TM2 18
-#define EPIC_VECTOR_TM3 19
-#define EPIC_VECTOR_I2C 20
-#define EPIC_VECTOR_DMA0 21
-#define EPIC_VECTOR_DMA1 22
-#define EPIC_VECTOR_I2O 23
-
-
-#define INT_VEC_IRQ0 0
-#define INT_NUM_IRQ0 INT_VEC_IRQ0
-#define MOUSSE_IRQ_ENET EPIC_VECTOR_EXT1 /* Hardwired */
-#define MOUSSE_IRQ_CPCI EPIC_VECTOR_EXT2 /* Hardwired */
-#define MOUSSE_IRQ_LPCI EPIC_VECTOR_EXT3 /* Hardwired */
-#define MOUSSE_IRQ_DUART EPIC_VECTOR_EXT4 /* Hardwired */
-
-/* Onboard DEC 21143 Ethernet */
-#define PCI_ENET_MEMADDR 0x80000000
-#define PCI_ENET_IOADDR 0x80000000
-
-/* Some other PCI device */
-#define PCI_SLOT_MEMADDR 0x81000000
-#define PCI_SLOT_IOADDR 0x81000000
-
-/* Promise ATA66 PCI Device (ATA controller) */
-#define PROMISE_MBAR0 0xa0000000
-#define PROMISE_MBAR1 (PROMISE_MBAR0 + 0x1000)
-#define PROMISE_MBAR2 (PROMISE_MBAR0 + 0x2000)
-#define PROMISE_MBAR3 (PROMISE_MBAR0 + 0x3000)
-#define PROMISE_MBAR4 (PROMISE_MBAR0 + 0x4000)
-#define PROMISE_MBAR5 (PROMISE_MBAR0 + 0x5000)
-
-/* ATA/66 Controller offsets */
-#define CONFIG_SYS_ATA_BASE_ADDR PROMISE_MBAR0
-#define CONFIG_SYS_IDE_MAXBUS 2 /* ide0/ide1 */
-#define CONFIG_SYS_IDE_MAXDEVICE 2 /* 2 drives per controller */
-#define CONFIG_SYS_ATA_IDE0_OFFSET 0
-#define CONFIG_SYS_ATA_IDE1_OFFSET 0x3000
-/*
- * Definitions for accessing IDE controller registers
- */
-#define CONFIG_SYS_ATA_DATA_OFFSET 0
-#define CONFIG_SYS_ATA_REG_OFFSET 0
-#define CONFIG_SYS_ATA_ALT_OFFSET (0x1000)
-
-/*
- * The constants ROM_TEXT_ADRS, ROM_SIZE, RAM_HIGH_ADRS, and RAM_LOW_ADRS
- * are defined in config.h and Makefile.
- * All definitions for these constants must be identical.
- */
-#define ROM_BASE_ADRS 0xfff00000 /* base address of ROM */
-#define ROM_TEXT_ADRS (ROM_BASE_ADRS+0x0100) /* with PC & SP */
-#define ROM_WARM_ADRS (ROM_TEXT_ADRS+0x0004) /* warm reboot entry */
-#define ROM_SIZE 0x00080000 /* 512KB ROM space */
-#define RAM_LOW_ADRS 0x00010000 /* RAM address for vxWorks */
-#define RAM_HIGH_ADRS 0x00c00000 /* RAM address for bootrom */
-
-/*
- * NVRAM configuration
- * NVRAM is implemented via the SGS Thomson M48T59Y
- * 64Kbit (8Kbx8) Timekeeper SRAM.
- * This 8KB NVRAM also has a TOD. See m48t59y.{h,c} for more information.
- */
-
-#define NV_RAM_ADRS TOD_NVRAM_BASE
-#define NV_RAM_INTRVL 1
-#define NV_RAM_WR_ENBL SYS_TOD_UNPROTECT()
-#define NV_RAM_WR_DSBL SYS_TOD_PROTECT()
-
-#define NV_OFF_BOOT0 0x0000 /* Boot string 0 (256b) */
-#define NV_OFF_BOOT1 0x0100 /* Boot string 1 (256b) */
-#define NV_OFF_BOOT2 0x0200 /* Boot string 2 (256b)*/
-#define NV_OFF_MACADDR 0x0400 /* 21143 MAC address (6b) */
-#define NV_OFF_ACTIVEBOOT 0x0406 /* Active boot string, 0 to 2 (1b) */
-#define NV_OFF_UNUSED1 0x0407 /* Unused (1b) */
-#define NV_OFF_BINDFIX 0x0408 /* See sysLib.c:sysBindFix() (1b) */
-#define NV_OFF_UNUSED2 0x0409 /* Unused (7b) */
-#define NV_OFF_TIMEZONE 0x0410 /* TIMEZONE env var (64b) */
-#define NV_OFF_VXWORKS_END 0x07FF /* 2047 VxWorks Total */
-#define NV_OFF_U_BOOT 0x0800 /* 2048 U-Boot boot-loader */
-#define NV_OFF_U_BOOT_ADDR (TOD_BASE + NV_OFF_U_BOOT) /* sysaddr*/
-#define NV_U_BOOT_ENV_SIZE 2048 /* 2K - U-Boot Total */
-#define NV_OFF__next_free (NV_U_BOOT_ENVSIZE +1)
-#define NV_RAM_SIZE 8176 /* NVRAM End */
-
-#endif /* __MOUSSE_H */
+++ /dev/null
-/*
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2001
- * James Dougherty (jfd@cs.stanford.edu)
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * PCI Configuration space access support for MPC824x/MPC107 PCI Bridge
- */
-#include <common.h>
-#include <mpc824x.h>
-#include <pci.h>
-
-#include "mousse.h"
-
-/*
- * Promise ATA/66 support.
- */
-#define XFER_PIO_4 0x0C /* 0000|1100 */
-#define XFER_PIO_3 0x0B /* 0000|1011 */
-#define XFER_PIO_2 0x0A /* 0000|1010 */
-#define XFER_PIO_1 0x09 /* 0000|1001 */
-#define XFER_PIO_0 0x08 /* 0000|1000 */
-#define XFER_PIO_SLOW 0x00 /* 0000|0000 */
-
-/* Promise Regs */
-#define REG_A 0x01
-#define REG_B 0x02
-#define REG_C 0x04
-#define REG_D 0x08
-
-void
-pdc202xx_decode_registers (unsigned char registers, unsigned char value)
-{
- unsigned char bit = 0, bit1 = 0, bit2 = 0;
- switch(registers) {
- case REG_A:
- bit2 = 0;
- printf(" A Register ");
- if (value & 0x80) printf("SYNC_IN ");
- if (value & 0x40) printf("ERRDY_EN ");
- if (value & 0x20) printf("IORDY_EN ");
- if (value & 0x10) printf("PREFETCH_EN ");
- if (value & 0x08) { printf("PA3 ");bit2 |= 0x08; }
- if (value & 0x04) { printf("PA2 ");bit2 |= 0x04; }
- if (value & 0x02) { printf("PA1 ");bit2 |= 0x02; }
- if (value & 0x01) { printf("PA0 ");bit2 |= 0x01; }
- printf("PIO(A) = %d ", bit2);
- break;
- case REG_B:
- bit1 = 0;bit2 = 0;
- printf(" B Register ");
- if (value & 0x80) { printf("MB2 ");bit1 |= 0x80; }
- if (value & 0x40) { printf("MB1 ");bit1 |= 0x40; }
- if (value & 0x20) { printf("MB0 ");bit1 |= 0x20; }
- printf("DMA(B) = %d ", bit1 >> 5);
- if (value & 0x10) printf("PIO_FORCED/PB4 ");
- if (value & 0x08) { printf("PB3 ");bit2 |= 0x08; }
- if (value & 0x04) { printf("PB2 ");bit2 |= 0x04; }
- if (value & 0x02) { printf("PB1 ");bit2 |= 0x02; }
- if (value & 0x01) { printf("PB0 ");bit2 |= 0x01; }
- printf("PIO(B) = %d ", bit2);
- break;
- case REG_C:
- bit2 = 0;
- printf(" C Register ");
- if (value & 0x80) printf("DMARQp ");
- if (value & 0x40) printf("IORDYp ");
- if (value & 0x20) printf("DMAR_EN ");
- if (value & 0x10) printf("DMAW_EN ");
-
- if (value & 0x08) { printf("MC3 ");bit2 |= 0x08; }
- if (value & 0x04) { printf("MC2 ");bit2 |= 0x04; }
- if (value & 0x02) { printf("MC1 ");bit2 |= 0x02; }
- if (value & 0x01) { printf("MC0 ");bit2 |= 0x01; }
- printf("DMA(C) = %d ", bit2);
- break;
- case REG_D:
- printf(" D Register ");
- break;
- default:
- return;
- }
- printf("\n %s ", (registers & REG_D) ? "DP" :
- (registers & REG_C) ? "CP" :
- (registers & REG_B) ? "BP" :
- (registers & REG_A) ? "AP" : "ERROR");
- for (bit=128;bit>0;bit/=2)
- printf("%s", (value & bit) ? "1" : "0");
- printf("\n");
-}
-
-/*
- * Promise ATA/66 Support: configure Promise ATA66 card in specified mode.
- */
-int
-pdc202xx_tune_chipset (pci_dev_t dev, int drive, unsigned char speed)
-{
- unsigned short drive_conf;
- int err = 0;
- unsigned char drive_pci, AP, BP, CP, DP;
- unsigned char TA = 0, TB = 0;
-
- switch (drive) {
- case 0: drive_pci = 0x60; break;
- case 1: drive_pci = 0x64; break;
- case 2: drive_pci = 0x68; break;
- case 3: drive_pci = 0x6c; break;
- default: return -1;
- }
-
- pci_read_config_word(dev, drive_pci, &drive_conf);
- pci_read_config_byte(dev, (drive_pci), &AP);
- pci_read_config_byte(dev, (drive_pci)|0x01, &BP);
- pci_read_config_byte(dev, (drive_pci)|0x02, &CP);
- pci_read_config_byte(dev, (drive_pci)|0x03, &DP);
-
- if ((AP & 0x0F) || (BP & 0x07)) {
- /* clear PIO modes of lower 8421 bits of A Register */
- pci_write_config_byte(dev, (drive_pci), AP & ~0x0F);
- pci_read_config_byte(dev, (drive_pci), &AP);
-
- /* clear PIO modes of lower 421 bits of B Register */
- pci_write_config_byte(dev, (drive_pci)|0x01, BP & ~0x07);
- pci_read_config_byte(dev, (drive_pci)|0x01, &BP);
-
- pci_read_config_byte(dev, (drive_pci), &AP);
- pci_read_config_byte(dev, (drive_pci)|0x01, &BP);
- }
-
- pci_read_config_byte(dev, (drive_pci), &AP);
- pci_read_config_byte(dev, (drive_pci)|0x01, &BP);
- pci_read_config_byte(dev, (drive_pci)|0x02, &CP);
-
- switch(speed) {
- case XFER_PIO_4: TA = 0x01; TB = 0x04; break;
- case XFER_PIO_3: TA = 0x02; TB = 0x06; break;
- case XFER_PIO_2: TA = 0x03; TB = 0x08; break;
- case XFER_PIO_1: TA = 0x05; TB = 0x0C; break;
- case XFER_PIO_0:
- default: TA = 0x09; TB = 0x13; break;
- }
-
- pci_write_config_byte(dev, (drive_pci), AP|TA);
- pci_write_config_byte(dev, (drive_pci)|0x01, BP|TB);
-
- pci_read_config_byte(dev, (drive_pci), &AP);
- pci_read_config_byte(dev, (drive_pci)|0x01, &BP);
- pci_read_config_byte(dev, (drive_pci)|0x02, &CP);
- pci_read_config_byte(dev, (drive_pci)|0x03, &DP);
-
-
-#ifdef PDC202XX_DEBUG
- pdc202xx_decode_registers(REG_A, AP);
- pdc202xx_decode_registers(REG_B, BP);
- pdc202xx_decode_registers(REG_C, CP);
- pdc202xx_decode_registers(REG_D, DP);
-#endif
- return err;
-}
-/*
- * Show/Init PCI devices on the specified bus number.
- */
-
-void pci_mousse_fixup_irq(struct pci_controller *hose, pci_dev_t dev)
-{
- unsigned int line;
-
- switch(PCI_DEV(dev)) {
- case 0x0d:
- line = 0x00000101;
- break;
-
- case 0x0e:
- default:
- line = 0x00000303;
- break;
- }
-
- pci_write_config_dword(dev, PCI_INTERRUPT_LINE, line);
-}
-
-void pci_mousse_setup_pdc202xx(struct pci_controller *hose, pci_dev_t dev,
- struct pci_config_table *_)
-{
- unsigned short vendorId;
- unsigned int mbar0, cmd;
- int bar, a;
-
- pci_read_config_word(dev, PCI_VENDOR_ID, &vendorId);
-
- if(vendorId == PCI_VENDOR_ID_PROMISE || vendorId == PCI_VENDOR_ID_CMD){
- /* PDC 202xx card is handled differently, it is a bootable
- * device and needs all 5 MBAR's configured
- */
- for(bar = 0; bar < 5; bar++){
- pci_read_config_dword(dev, PCI_BASE_ADDRESS_0+bar*4, &mbar0);
- pci_write_config_dword(dev, PCI_BASE_ADDRESS_0+bar*4, ~0);
- pci_read_config_dword(dev, PCI_BASE_ADDRESS_0+bar*4, &mbar0);
-#ifdef DEBUG
- printf(" ATA_bar[%d] = %dbytes\n", bar,
- ~(mbar0 & PCI_BASE_ADDRESS_MEM_MASK) + 1);
-#endif
- }
-
- /* Program all BAR's */
- pci_write_config_dword(dev, PCI_BASE_ADDRESS_0, PROMISE_MBAR0);
- pci_write_config_dword(dev, PCI_BASE_ADDRESS_1, PROMISE_MBAR1);
- pci_write_config_dword(dev, PCI_BASE_ADDRESS_2, PROMISE_MBAR2);
- pci_write_config_dword(dev, PCI_BASE_ADDRESS_3, PROMISE_MBAR3);
- pci_write_config_dword(dev, PCI_BASE_ADDRESS_4, PROMISE_MBAR4);
- pci_write_config_dword(dev, PCI_BASE_ADDRESS_5, PROMISE_MBAR5);
-
- for(bar = 0; bar < 5; bar++){
- pci_read_config_dword(dev, PCI_BASE_ADDRESS_0+bar*4, &mbar0);
-#ifdef DEBUG
- printf(" ATA_bar[%d]@0x%x\n", bar, mbar0);
-#endif
- }
-
- /* Enable ROM Expansion base */
- pci_write_config_dword(dev, PCI_ROM_ADDRESS, PROMISE_MBAR5|1);
-
- /* Io enable, Memory enable, master enable */
- pci_read_config_dword(dev, PCI_COMMAND, &cmd);
- cmd &= ~0xffff0000;
- cmd |= PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY | PCI_COMMAND_IO;
- pci_write_config_dword(dev, PCI_COMMAND, cmd);
-
- /* Breath some life into the controller */
- for( a = 0; a < 4; a++)
- pdc202xx_tune_chipset(dev, a, XFER_PIO_0);
- }
-}
-
-static struct pci_config_table pci_sandpoint_config_table[] = {
- { PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 0x00, 0x0e, 0x00,
- pci_mousse_setup_pdc202xx },
-#ifndef CONFIG_PCI_PNP
- { PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 0x00, 0x0d, 0x00,
- pci_cfgfunc_config_device, {PCI_ENET_IOADDR,
- PCI_ENET_MEMADDR,
- PCI_COMMAND_MEMORY |
- PCI_COMMAND_MASTER}},
- { PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
- pci_cfgfunc_config_device, {PCI_SLOT_IOADDR,
- PCI_SLOT_MEMADDR,
- PCI_COMMAND_MEMORY |
- PCI_COMMAND_MASTER}},
-#endif
- { }
-};
-
-struct pci_controller hose = {
- config_table: pci_sandpoint_config_table,
- fixup_irq: pci_mousse_fixup_irq,
-};
-
-void pci_init_board(void)
-{
- pci_mpc824x_init(&hose);
-}
+++ /dev/null
-/*
- * (C) Copyright 2001
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-OUTPUT_ARCH(powerpc)
-/* Do we need any of these for elf?
- __DYNAMIC = 0; */
-SECTIONS
-{
- /* Read-only sections, merged into text segment: */
- .text :
- {
- arch/powerpc/cpu/mpc824x/start.o (.text*)
- *(.text*)
- . = ALIGN(16);
- *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
- }
-
- /* Read-write section, merged into data segment: */
- . = (. + 0x0FF) & 0xFFFFFF00;
- _erotext = .;
- PROVIDE (erotext = .);
- .reloc :
- {
- _GOT2_TABLE_ = .;
- KEEP(*(.got2))
- KEEP(*(.got))
- PROVIDE(_GLOBAL_OFFSET_TABLE_ = . + 4);
- _FIXUP_TABLE_ = .;
- KEEP(*(.fixup))
- }
- __got2_entries = ((_GLOBAL_OFFSET_TABLE_ - _GOT2_TABLE_) >> 2) - 1;
- __fixup_entries = (. - _FIXUP_TABLE_) >> 2;
-
- .data :
- {
- *(.data*)
- *(.sdata*)
- }
- _edata = .;
- PROVIDE (edata = .);
-
- . = .;
-
- . = ALIGN(4);
- .u_boot_list : {
- KEEP(*(SORT(.u_boot_list*)));
- }
-
-
- . = .;
- __start___ex_table = .;
- __ex_table : { *(__ex_table) }
- __stop___ex_table = .;
-
- . = ALIGN(4096);
- __init_begin = .;
- .text.init : { *(.text.init) }
- .data.init : { *(.data.init) }
- . = ALIGN(4096);
- __init_end = .;
-
- __bss_start = .;
- .bss (NOLOAD) :
- {
- *(.bss*)
- *(.sbss*)
- *(COMMON)
- . = ALIGN(4);
- }
-
- __bss_end = . ;
- PROVIDE (end = .);
-}
+++ /dev/null
-/*
- * (C) Copyright 2000
- * Rob Taylor, Flying Pig Systems Ltd. robt@flyingpig.com
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-OUTPUT_ARCH(powerpc)
-
-MEMORY {
- ram (!rx) : org = 0x00000000 , LENGTH = 8M
- code (!rx) : org = 0x00002000 , LENGTH = (4M - 0x2000)
- rom (rx) : org = 0xfff00000 , LENGTH = 512K
-}
-
-SECTIONS
-{
- _f_init = .;
- PROVIDE(_f_init = .);
- _f_init_rom = .;
- PROVIDE(_f_init_rom = .);
-
- .init : {
- arch/powerpc/cpu/mpc824x/start.o (.text)
- *(.init)
- } > ram
- _init_size = SIZEOF(.init);
- PROVIDE(_init_size = SIZEOF(.init));
-
- ENTRY(_start)
-
-/* _ftext = .;
- _ftext_rom = .;
- _text_size = SIZEOF(.text);
- */
- .text : {
- *(.text)
- *(.got1)
- } > ram
- .rodata : { *(.rodata) } > ram
- .dtors : { *(.dtors) } > ram
- .data : { *(.data) } > ram
- .sdata : { *(.sdata) } > ram
- .sdata2 : { *(.sdata2)
- *(.got)
- _GOT2_TABLE_ = .;
- *(.got2)
- _FIXUP_TABLE_ = .;
- *(.fixup)
- } > ram
- __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
- __fixup_entries = (. - _FIXUP_TABLE_)>>2;
-
- .sbss : { *(.sbss) } > ram
- .sbss2 : { *(.sbss2) } > ram
- .bss : { *(.bss) } > ram
- .debug : { *(.debug) } > ram
- .line : { *(.line) } > ram
- .symtab : { *(.symtab) } > ram
- .shrstrtab : { *(.shstrtab) } > ram
- .strtab : { *(.strtab) } > ram
- /* .reloc :
- {
- *(.got)
- _GOT2_TABLE_ = .;
- *(.got2)
- _FIXUP_TABLE_ = .;
- *(.fixup)
- } > ram
- */
-
-
- __start___ex_table = .;
- __ex_table : { *(__ex_table) } > ram
- __stop___ex_table = .;
-
-
- .ppcenv :
- {
- common/env_embedded.o (.ppcenv)
- } > ram
-
- __bss_end = . ;
- PROVIDE (end = .);
-}
+++ /dev/null
-/*
- * (C) Copyright 2001
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-OUTPUT_ARCH(powerpc)
-/* Do we need any of these for elf?
- __DYNAMIC = 0; */
-SECTIONS
-{
- /* Read-only sections, merged into text segment: */
- . = + SIZEOF_HEADERS;
- .interp : { *(.interp) }
- .hash : { *(.hash) }
- .dynsym : { *(.dynsym) }
- .dynstr : { *(.dynstr) }
- .rel.text : { *(.rel.text) }
- .rela.text : { *(.rela.text) }
- .rel.data : { *(.rel.data) }
- .rela.data : { *(.rela.data) }
- .rel.rodata : { *(.rel.rodata) }
- .rela.rodata : { *(.rela.rodata) }
- .rel.got : { *(.rel.got) }
- .rela.got : { *(.rela.got) }
- .rel.ctors : { *(.rel.ctors) }
- .rela.ctors : { *(.rela.ctors) }
- .rel.dtors : { *(.rel.dtors) }
- .rela.dtors : { *(.rela.dtors) }
- .rel.bss : { *(.rel.bss) }
- .rela.bss : { *(.rela.bss) }
- .rel.plt : { *(.rel.plt) }
- .rela.plt : { *(.rela.plt) }
- .init : { *(.init) }
- .plt : { *(.plt) }
- .text :
- {
- arch/powerpc/cpu/mpc824x/start.o (.text)
- common/board.o (.text)
- arch/powerpc/lib/ppcstring.o (.text)
- lib/vsprintf.o (.text)
- lib/crc32.o (.text)
- lib/zlib.o (.text)
-
- . = env_offset;
- common/env_embedded.o (.text)
-
- *(.text)
-
- *(.got1)
- . = ALIGN(16);
- *(.rodata)
- *(.rodata1)
- *(.rodata.str1.4)
- *(.eh_frame)
- }
- .fini : { *(.fini) } =0
- .ctors : { *(.ctors) }
- .dtors : { *(.dtors) }
-
- /* Read-write section, merged into data segment: */
- . = (. + 0x0FF) & 0xFFFFFF00;
- _erotext = .;
- PROVIDE (erotext = .);
- .reloc :
- {
- *(.got)
- _GOT2_TABLE_ = .;
- *(.got2)
- _FIXUP_TABLE_ = .;
- *(.fixup)
- }
- __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2;
- __fixup_entries = (. - _FIXUP_TABLE_) >> 2;
-
- .data :
- {
- *(.data)
- *(.data1)
- *(.sdata)
- *(.sdata2)
- *(.dynamic)
- CONSTRUCTORS
- }
- _edata = .;
- PROVIDE (edata = .);
-
-
- __start___ex_table = .;
- __ex_table : { *(__ex_table) }
- __stop___ex_table = .;
-
- . = ALIGN(4096);
- __init_begin = .;
- .text.init : { *(.text.init) }
- .data.init : { *(.data.init) }
- . = ALIGN(4096);
- __init_end = .;
-
- __bss_start = .;
- .bss :
- {
- *(.sbss) *(.scommon)
- *(.dynbss)
- *(.bss)
- *(COMMON)
- }
-
- __bss_end = . ;
- PROVIDE (end = .);
-}
Orphan arm arm1136 mx31 freescale - mx31ads - (resigned) Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Orphan arm pxa - - - lubbock - (dead address) Kyle Harris <kharris@nexus-tech.net>
Orphan powerpc 74xx_7xx - - evb64260 EVB64260 - -
-Orphan powerpc mpc824x - - mousse MOUSSE - -
Board Arch CPU Commit Removed Last known maintainer/contact
=================================================================================================
+MOUSSE powerpc mpc824x - 2014-04-04
rsdproto powerpc mpc8260 - 2014-04-04
RPXsuper powerpc mpc8260 - 2014-04-04
RPXClassic powerpc mpc8xx - 2014-04-04
+++ /dev/null
-/*
- * (C) Copyright 2000, 2001
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2001
- * James F. Dougherty (jfd@cs.stanford.edu)
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- *
- * Configuration settings for the MOUSSE board.
- * See also: http://www.vooha.com/
- *
- */
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC8240 1
-#define CONFIG_MOUSSE 1
-
-#define CONFIG_SYS_TEXT_BASE 0xFFF00000
-#define CONFIG_SYS_LDSCRIPT "board/mousse/u-boot.lds"
-
-#define CONFIG_SYS_ADDR_MAP_B 1
-
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_BAUDRATE 9600
-#if 1
-#define CONFIG_BOOTCOMMAND "tftp 100000 vmlinux.img;bootm" /* autoboot command */
-#else
-#define CONFIG_BOOTCOMMAND "bootm ffe10000"
-#endif
-#define CONFIG_BOOTARGS "console=ttyS0 root=/dev/nfs rw nfsroot=209.128.93.133:/boot nfsaddrs=209.128.93.133:209.128.93.138"
-#define CONFIG_BOOTDELAY 3
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DATE
-
-
-#define CONFIG_ENV_OVERWRITE 1
-#define CONFIG_ETH_ADDR "00:10:18:10:00:06"
-
-#define CONFIG_DOS_PARTITION 1 /* MSDOS bootable partitiion support */
-
-#include "../board/mousse/mousse.h"
-
-/*
- * Miscellaneous configurable options
- */
-#undef CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_MAXARGS 8 /* Max number of command args */
-
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* Default load address */
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-
-#ifdef DEBUG
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_SDRAM_BASE
-#else
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#endif
-
-#ifdef DEBUG
-#define CONFIG_SYS_MONITOR_LEN (4 << 20) /* lots of mem ... */
-#else
-#define CONFIG_SYS_MONITOR_LEN (512 << 10) /* 512K PLCC bootrom */
-#endif
-#define CONFIG_SYS_MALLOC_LEN (2*(4096 << 10)) /* 2*4096kB for malloc() */
-
-#define CONFIG_SYS_MEMTEST_START 0x00004000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x02000000 /* 0 ... 32 MB in DRAM */
-
-
-#define CONFIG_SYS_EUMB_ADDR 0xFC000000
-
-#define CONFIG_SYS_ISA_MEM 0xFD000000
-#define CONFIG_SYS_ISA_IO 0xFE000000
-
-#define CONFIG_SYS_FLASH_BASE 0xFFF00000
-#define CONFIG_SYS_FLASH_SIZE ((uint)(512 * 1024))
-#define CONFIG_SYS_RESET_ADDRESS 0xFFF00100
-#define FLASH_BASE0_PRELIM 0xFFF00000 /* 512K PLCC FLASH/AM29F040*/
-#define FLASH_BASE0_SIZE 0x80000 /* 512K */
-#define FLASH_BASE1_PRELIM 0xFFE10000 /* AMD 29LV160DB
- 1MB - 64K FLASH0 SEG =960K
- (size=0xf0000)*/
-
-/*
- * NS16550 Configuration
- */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-
-#define CONFIG_SYS_NS16550_CLK 18432000
-
-#define CONFIG_SYS_NS16550_COM1 0xFFE08080
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_SDRAM_BASE + CONFIG_SYS_MONITOR_LEN
-#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- * For the detail description refer to the MPC8240 user's manual.
- */
-
-#define CONFIG_SYS_CLK_FREQ 33000000 /* external frequency to pll */
-#define CONFIG_PLL_PCI_TO_MEM_MULTIPLIER 2
-
-#define CONFIG_SYS_ETH_DEV_FN 0x00
-#define CONFIG_SYS_ETH_IOBASE 0x00104000
-
-
- /* Bit-field values for MCCR1.
- */
-#define CONFIG_SYS_ROMNAL 8
-#define CONFIG_SYS_ROMFAL 8
-
- /* Bit-field values for MCCR2.
- */
-#define CONFIG_SYS_REFINT 0xf5 /* Refresh interval */
-
- /* Burst To Precharge. Bits of this value go to MCCR3 and MCCR4.
- */
-#define CONFIG_SYS_BSTOPRE 0x79
-
-#ifdef INCLUDE_ECC
-#define USE_ECC 1
-#else /* INCLUDE_ECC */
-#define USE_ECC 0
-#endif /* INCLUDE_ECC */
-
-
- /* Bit-field values for MCCR3.
- */
-#define CONFIG_SYS_REFREC 8 /* Refresh to activate interval */
-#define CONFIG_SYS_RDLAT (4+USE_ECC) /* Data latancy from read command */
-
- /* Bit-field values for MCCR4.
- */
-#define CONFIG_SYS_PRETOACT 3 /* Precharge to activate interval */
-#define CONFIG_SYS_ACTTOPRE 5 /* Activate to Precharge interval */
-#define CONFIG_SYS_SDMODE_CAS_LAT 3 /* SDMODE CAS latancy */
-#define CONFIG_SYS_SDMODE_WRAP 0 /* SDMODE wrap type */
-#define CONFIG_SYS_SDMODE_BURSTLEN 2 /* SDMODE Burst length */
-#define CONFIG_SYS_ACTORW 2
-#define CONFIG_SYS_REGISTERD_TYPE_BUFFER (1-USE_ECC)
-
-/* Memory bank settings.
- * Only bits 20-29 are actually used from these vales to set the
- * start/end addresses. The upper two bits will always be 0, and the lower
- * 20 bits will be 0x00000 for a start address, or 0xfffff for an end
- * address. Refer to the MPC8240 book.
- */
-#define CONFIG_SYS_RAM_SIZE 0x04000000 /* 64MB */
-
-
-#define CONFIG_SYS_BANK0_START 0x00000000
-#define CONFIG_SYS_BANK0_END (CONFIG_SYS_RAM_SIZE - 1)
-#define CONFIG_SYS_BANK0_ENABLE 1
-#define CONFIG_SYS_BANK1_START 0x3ff00000
-#define CONFIG_SYS_BANK1_END 0x3fffffff
-#define CONFIG_SYS_BANK1_ENABLE 0
-#define CONFIG_SYS_BANK2_START 0x3ff00000
-#define CONFIG_SYS_BANK2_END 0x3fffffff
-#define CONFIG_SYS_BANK2_ENABLE 0
-#define CONFIG_SYS_BANK3_START 0x3ff00000
-#define CONFIG_SYS_BANK3_END 0x3fffffff
-#define CONFIG_SYS_BANK3_ENABLE 0
-#define CONFIG_SYS_BANK4_START 0x3ff00000
-#define CONFIG_SYS_BANK4_END 0x3fffffff
-#define CONFIG_SYS_BANK4_ENABLE 0
-#define CONFIG_SYS_BANK5_START 0x3ff00000
-#define CONFIG_SYS_BANK5_END 0x3fffffff
-#define CONFIG_SYS_BANK5_ENABLE 0
-#define CONFIG_SYS_BANK6_START 0x3ff00000
-#define CONFIG_SYS_BANK6_END 0x3fffffff
-#define CONFIG_SYS_BANK6_ENABLE 0
-#define CONFIG_SYS_BANK7_START 0x3ff00000
-#define CONFIG_SYS_BANK7_END 0x3fffffff
-#define CONFIG_SYS_BANK7_ENABLE 0
-
-#define CONFIG_SYS_ODCR 0x7f
-
-
-#define CONFIG_SYS_PGMAX 0x32 /* how long the 8240 reatins the currently accessed page in memory
- see 8240 book for details*/
-#define PCI_MEM_SPACE1_START 0x80000000
-#define PCI_MEM_SPACE2_START 0xfd000000
-
-/* IBAT/DBAT Configuration */
-/* Ram: 64MB, starts at address-0, r/w instruction/data */
-#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_64M | BATU_VS | BATU_VP)
-#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
-#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
-
-/* MPLD/Port-X I/O Space : data and instruction read/write, cache-inhibit */
-#define CONFIG_SYS_IBAT1U (PORTX_DEV_BASE | BATU_BL_128M | BATU_VS | BATU_VP)
-#if 0
-#define CONFIG_SYS_IBAT1L (PORTX_DEV_BASE | BATL_PP_10 | BATL_MEMCOHERENCE |\
- BATL_WRITETHROUGH | BATL_CACHEINHIBIT)
-#else
-#define CONFIG_SYS_IBAT1L (PORTX_DEV_BASE | BATL_PP_10 |BATL_CACHEINHIBIT)
-#endif
-#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
-#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
-
-/* PCI Memory region 1: 0x8XXX_XXXX PCI Mem space: EUMBAR, etc - 16MB */
-#define CONFIG_SYS_IBAT2U (PCI_MEM_SPACE1_START|BATU_BL_16M | BATU_VS | BATU_VP)
-#define CONFIG_SYS_IBAT2L (PCI_MEM_SPACE1_START|BATL_PP_10 | BATL_GUARDEDSTORAGE|BATL_CACHEINHIBIT)
-#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
-#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
-
-/* PCI Memory region 2: PCI Devices in 0xFD space */
-#define CONFIG_SYS_IBAT3U (PCI_MEM_SPACE2_START|BATU_BL_16M | BATU_VS | BATU_VP)
-#define CONFIG_SYS_IBAT3L (PCI_MEM_SPACE2_START|BATL_PP_10 | BATL_GUARDEDSTORAGE | BATL_CACHEINHIBIT)
-#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
-#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
-
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS 3 /* Max number of flash banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 64 /* Max number of sectors in one bank */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
-#if 0
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_OFFSET 0x8000 /* Offset of the Environment Sector */
-#define CONFIG_ENV_SIZE 0x4000 /* Size of the Environment Sector */
-#else
-#define CONFIG_ENV_IS_IN_NVRAM 1
-#define CONFIG_ENV_ADDR NV_OFF_U_BOOT_ADDR /* PortX NVM Free addr*/
-#define CONFIG_ENV_OFFSET CONFIG_ENV_ADDR
-#define CONFIG_ENV_SIZE NV_U_BOOT_ENV_SIZE /* 2K */
-#endif
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 16
-
-/* Localizations */
-#if 0
-#define CONFIG_ETHADDR 0:0:0:0:1:d
-#define CONFIG_IPADDR 172.16.40.113
-#define CONFIG_SERVERIP 172.16.40.111
-#else
-#define CONFIG_ETHADDR 0:0:0:0:1:d
-#define CONFIG_IPADDR 209.128.93.138
-#define CONFIG_SERVERIP 209.128.93.133
-#endif
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *-----------------------------------------------------------------------
- */
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
-#undef CONFIG_PCI_PNP
-
-
-#define CONFIG_TULIP
-
-#endif /* __CONFIG_H */
projects / karo-tx-uboot.git / commitdiff