#include <asm/fsl_law.h>
#include <asm/fsl_serdes.h>
#include <asm/fsl_srio.h>
+#include <fsl_usb.h>
#include <hwconfig.h>
#include <linux/compiler.h>
#include "mp.h"
#ifdef CONFIG_SYS_FSL_USB1_PHY_ENABLE
{
- ccsr_usb_phy_t *usb_phy1 =
+ struct ccsr_usb_phy __iomem *usb_phy1 =
(void *)CONFIG_SYS_MPC85xx_USB1_PHY_ADDR;
out_be32(&usb_phy1->usb_enable_override,
CONFIG_SYS_FSL_USB_ENABLE_OVERRIDE);
#endif
#ifdef CONFIG_SYS_FSL_USB2_PHY_ENABLE
{
- ccsr_usb_phy_t *usb_phy2 =
+ struct ccsr_usb_phy __iomem *usb_phy2 =
(void *)CONFIG_SYS_MPC85xx_USB2_PHY_ADDR;
out_be32(&usb_phy2->usb_enable_override,
CONFIG_SYS_FSL_USB_ENABLE_OVERRIDE);
#endif
#if defined(CONFIG_SYS_FSL_USB_DUAL_PHY_ENABLE)
- ccsr_usb_phy_t *usb_phy =
+ struct ccsr_usb_phy __iomem *usb_phy =
(void *)CONFIG_SYS_MPC85xx_USB1_PHY_ADDR;
setbits_be32(&usb_phy->pllprg[1],
CONFIG_SYS_FSL_USB_PLLPRG2_PHY2_CLK_EN |
#include <asm/errno.h>
#include "fsl_corenet2_serdes.h"
+#ifdef CONFIG_SYS_FSL_SRDS_1
static u64 serdes1_prtcl_map;
+#endif
+#ifdef CONFIG_SYS_FSL_SRDS_2
static u64 serdes2_prtcl_map;
+#endif
#ifdef CONFIG_SYS_FSL_SRDS_3
static u64 serdes3_prtcl_map;
#endif
{
u64 ret = 0;
+#ifdef CONFIG_SYS_FSL_SRDS_1
ret |= (1ULL << device) & serdes1_prtcl_map;
+#endif
+#ifdef CONFIG_SYS_FSL_SRDS_2
ret |= (1ULL << device) & serdes2_prtcl_map;
+#endif
#ifdef CONFIG_SYS_FSL_SRDS_3
ret |= (1ULL << device) & serdes3_prtcl_map;
#endif
int i;
switch (sd) {
+#ifdef CONFIG_SYS_FSL_SRDS_1
case FSL_SRDS_1:
cfg &= FSL_CORENET2_RCWSR4_SRDS1_PRTCL;
cfg >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
break;
+#endif
+#ifdef CONFIG_SYS_FSL_SRDS_2
case FSL_SRDS_2:
cfg &= FSL_CORENET2_RCWSR4_SRDS2_PRTCL;
cfg >>= FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT;
break;
+#endif
#ifdef CONFIG_SYS_FSL_SRDS_3
case FSL_SRDS_3:
cfg &= FSL_CORENET2_RCWSR4_SRDS3_PRTCL;
void fsl_serdes_init(void)
{
+#ifdef CONFIG_SYS_FSL_SRDS_1
serdes1_prtcl_map = serdes_init(FSL_SRDS_1,
CONFIG_SYS_FSL_CORENET_SERDES_ADDR,
FSL_CORENET2_RCWSR4_SRDS1_PRTCL,
FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT);
+#endif
+#ifdef CONFIG_SYS_FSL_SRDS_2
serdes2_prtcl_map = serdes_init(FSL_SRDS_2,
CONFIG_SYS_FSL_CORENET_SERDES_ADDR + FSL_SRDS_2 * 0x1000,
FSL_CORENET2_RCWSR4_SRDS2_PRTCL,
FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT);
+#endif
#ifdef CONFIG_SYS_FSL_SRDS_3
serdes3_prtcl_map = serdes_init(FSL_SRDS_3,
CONFIG_SYS_FSL_CORENET_SERDES_ADDR + FSL_SRDS_3 * 0x1000,
{
const char *modes[] = { "host", "peripheral", "otg" };
const char *phys[] = { "ulpi", "utmi" };
- const char *mode = NULL;
- const char *phy_type = NULL;
const char *dr_mode_type = NULL;
const char *dr_phy_type = NULL;
- char usb1_defined = 0;
int usb_mode_off = -1;
int usb_phy_off = -1;
char str[5];
dr_mode_type = modes[mode_idx];
dr_phy_type = phys[phy_idx];
- /* use usb_dr_mode and usb_phy_type if
- usb1_defined = 0; these variables are to
- be deprecated */
- if (!strcmp(str, "usb1"))
- usb1_defined = 1;
-
if (mode_idx < 0 && phy_idx < 0) {
printf("WARNING: invalid phy or mode\n");
return;
if (usb_phy_off < 0)
return;
}
-
- if (!usb1_defined) {
- int usb_off = -1;
- mode = getenv("usb_dr_mode");
- phy_type = getenv("usb_phy_type");
- if (mode || phy_type) {
- printf("WARNING: usb_dr_mode and usb_phy_type "
- "are to be deprecated soon. Use "
- "hwconfig to set these values instead!!\n");
- fdt_fixup_usb_mode_phy_type(blob, mode,
- phy_type, usb_off);
- }
- }
}
#endif /* defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_MPH_USB) */
#endif
#define CONFIG_SYS_FSL_NUM_CC_PLLS 5
#define CONFIG_SYS_FSL_NUM_LAWS 32
+#define CONFIG_SYS_FSL_SRDS_1
+#define CONFIG_SYS_FSL_SRDS_2
#define CONFIG_SYS_FSL_SRDS_3
#define CONFIG_SYS_FSL_SRDS_4
#define CONFIG_SYS_FSL_SEC_COMPAT 4
#define CONFIG_SYS_FSL_QORIQ_CHASSIS2 /* Freescale Chassis generation 2 */
#define CONFIG_SYS_FSL_QMAN_V3 /* QMAN version 3 */
#define CONFIG_SYS_FSL_NUM_LAWS 32
+#define CONFIG_SYS_FSL_SRDS_1
+#define CONFIG_SYS_FSL_SRDS_2
#define CONFIG_SYS_FSL_SEC_COMPAT 4
#define CONFIG_SYS_NUM_FMAN 1
#define CONFIG_SYS_FSL_DDR_VER FSL_DDR_VER_4_7
u8 res4[0x400];
} ccsr_pme_t;
-#ifdef CONFIG_SYS_FSL_USB_DUAL_PHY_ENABLE
-struct ccsr_usb_port_ctrl {
- u32 ctrl;
- u32 drvvbuscfg;
- u32 pwrfltcfg;
- u32 sts;
- u8 res_14[0xc];
- u32 bistcfg;
- u32 biststs;
- u32 abistcfg;
- u32 abiststs;
- u8 res_30[0x10];
- u32 xcvrprg;
- u32 anaprg;
- u32 anadrv;
- u32 anasts;
-};
-
-typedef struct ccsr_usb_phy {
- u32 id;
- struct ccsr_usb_port_ctrl port1;
- u8 res_50[0xc];
- u32 tvr;
- u32 pllprg[4];
- u8 res_70[0x4];
- u32 anaccfg;
- u32 dbg;
- u8 res_7c[0x4];
- struct ccsr_usb_port_ctrl port2;
- u8 res_dc[0x334];
-} ccsr_usb_phy_t;
-
-#define CONFIG_SYS_FSL_USB_CTRL_PHY_EN (1 << 0)
-#define CONFIG_SYS_FSL_USB_DRVVBUS_CR_EN (1 << 1)
-#define CONFIG_SYS_FSL_USB_PWRFLT_CR_EN (1 << 1)
-#define CONFIG_SYS_FSL_USB_PLLPRG2_PHY2_CLK_EN (1 << 0)
-#define CONFIG_SYS_FSL_USB_PLLPRG2_PHY1_CLK_EN (1 << 1)
-#define CONFIG_SYS_FSL_USB_PLLPRG2_MFI (5 << 16)
-#define CONFIG_SYS_FSL_USB_PLLPRG2_PLL_EN (1 << 21)
-#else
-typedef struct ccsr_usb_phy {
- u8 res0[0x18];
- u32 usb_enable_override;
- u8 res[0xe4];
-} ccsr_usb_phy_t;
-#define CONFIG_SYS_FSL_USB_ENABLE_OVERRIDE 1
-#endif
-
#ifdef CONFIG_SYS_FSL_RAID_ENGINE
struct ccsr_raide {
u8 res0[0x543];
--- /dev/null
+Overview
+=========
+C29XPCIE board is a series of Freescale PCIe add-in cards to perform
+as public key crypto accelerator or secure key management module.
+It includes C293PCIE board, C293PCIE board and C291PCIE board.
+The Freescale C29x family is a high performance crypto co-processor.
+It combines a single e500v2 core with necessary SEC engines.
+(maximum core frequency 1000/1200 MHz).
+
+The C29xPCIE board features are as follows:
+Memory subsystem:
+ - 512Mbyte unbuffered DDR3 SDRAM discrete devices (32-bit bus)
+ - 64 Mbyte NOR flash single-chip memory
+ - 4 Gbyte NAND flash memory
+ - 1 Mbit AT24C1024 I2C EEPROM
+ - 16 Mbyte SPI memory
+
+Interfaces:
+ - 10/100/1000 BaseT Ethernet ports:
+ - eTSEC1, RGMII: one 10/100/1000 port
+ - eTSEC2, RGMII: one 10/100/1000 port
+ - DUART interface:
+ - DUART interface: supports two UARTs up to 115200 bps for
+ console display
+
+Board connectors:
+ - Mini-ITX power supply connector
+ - JTAG/COP for debugging
+
+Physical Memory Map on C29xPCIE
+===============================
+Address Start Address End Memory type
+0x0_0000_0000 - 0x0_1fff_ffff 512MB DDR
+0xc_0000_0000 - 0xc_8fff_ffff 256MB PCIE memory
+0xf_ec00_0000 - 0xf_efff_ffff 64MB NOR flash
+0xf_ffb0_0000 - 0xf_ffb7_ffff 512KB SRAM
+0xf_ffc0_0000 - 0xf_ffc0_ffff 64KB PCIE IO
+0xf_ffdf_0000 - 0xf_ffdf_0fff 4KB CPLD
+0xf_ffe0_0000 - 0xf_ffef_ffff 1MB CCSR
+
+Serial Port Configuration on C29xPCIE
+=====================================
+Configure the serial port of the attached computer with the following values:
+ -Data rate: 115200 bps
+ -Number of data bits: 8
+ -Parity: None
+ -Number of Stop bits: 1
+ -Flow Control: Hardware/None
+
+Settings of DIP-switch
+======================
+ SW5[1:4]= 1111 and SW5[6]=0 for boot from 16bit NOR flash
+ SW5[1:4]= 0110 and SW5[6]=0 for boot from SPI flash
+Note: 1 stands for 'off', 0 stands for 'on'
+
+Build and program u-boot to NOR flash
+==================================
+1. Build u-boot.bin image example:
+ export ARCH=powerpc
+ export CROSS_COMPILE=/your_path/powerpc-linux-gnu-
+ make C293PCIE
+
+2. Program u-boot.bin into NOR flash
+ => tftp $loadaddr $uboot
+ => protect off eff80000 +$filesize
+ => erase eff80000 +$filesize
+ => cp.b $loadaddr eff80000 $filesize
+
+3. Check SW5[1:4]= 1111 and SW5[6]=0, then power on.
+
+Alternate NOR bank
+==================
+There are four banks in C29XPCIE board, example to change bank booting:
+1. Program u-boot.bin into alternate NOR bank
+ => tftp $loadaddr $uboot
+ => protect off e9f80000 +$filesize
+ => erase e9f80000 +$filesize
+ => cp.b $loadaddr e9f80000 $filesize
+
+2. Switch to alternate NOR bank
+ => cpld_cmd reset altbank [bank]
+ - [bank] bank value select 1-4
+ - bank 1 on the flash 0x0000000~0x0ffffff
+ - bank 2 on the flash 0x1000000~0x1ffffff
+ - bank 3 on the flash 0x2000000~0x2ffffff
+ - bank 4 on the flash 0x3000000~0x3ffffff
+ or set SW5[7]= ON/OFF and SW5[7]= ON/OFF, then power on again.
+
+Build and program u-boot to SPI flash
+==================================
+1. Build u-boot-spi.bin image
+ make C29xPCIE_SPIFLASH_config; make
+ Need the boot_format tool to generate u-boot-spi.bin from the u-boot.bin.
+
+2. Program u-boot-spi.bin into SPI flash
+ => tftp $loadaddr $uboot-spi
+ => sf erase 0 100000
+ => sf write $loadaddr 0 $filesize
+
+3. Check SW5[1:4]= 0110 and SW5[6]=0, then power on.
--- /dev/null
+/*
+ * Freescale USB Controller
+ *
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef _ASM_FSL_USB_H_
+#define _ASM_FSL_USB_H_
+
+#ifdef CONFIG_SYS_FSL_USB_DUAL_PHY_ENABLE
+struct ccsr_usb_port_ctrl {
+ u32 ctrl;
+ u32 drvvbuscfg;
+ u32 pwrfltcfg;
+ u32 sts;
+ u8 res_14[0xc];
+ u32 bistcfg;
+ u32 biststs;
+ u32 abistcfg;
+ u32 abiststs;
+ u8 res_30[0x10];
+ u32 xcvrprg;
+ u32 anaprg;
+ u32 anadrv;
+ u32 anasts;
+};
+
+struct ccsr_usb_phy {
+ u32 id;
+ struct ccsr_usb_port_ctrl port1;
+ u8 res_50[0xc];
+ u32 tvr;
+ u32 pllprg[4];
+ u8 res_70[0x4];
+ u32 anaccfg;
+ u32 dbg;
+ u8 res_7c[0x4];
+ struct ccsr_usb_port_ctrl port2;
+ u8 res_dc[0x334];
+};
+
+#define CONFIG_SYS_FSL_USB_CTRL_PHY_EN (1 << 0)
+#define CONFIG_SYS_FSL_USB_DRVVBUS_CR_EN (1 << 1)
+#define CONFIG_SYS_FSL_USB_PWRFLT_CR_EN (1 << 1)
+#define CONFIG_SYS_FSL_USB_PLLPRG1_PHY_DIV (1 << 0)
+#define CONFIG_SYS_FSL_USB_PLLPRG2_PHY2_CLK_EN (1 << 0)
+#define CONFIG_SYS_FSL_USB_PLLPRG2_PHY1_CLK_EN (1 << 1)
+#define CONFIG_SYS_FSL_USB_PLLPRG2_FRAC_LPF_EN (1 << 13)
+#define CONFIG_SYS_FSL_USB_PLLPRG2_REF_DIV (1 << 4)
+#define CONFIG_SYS_FSL_USB_PLLPRG2_MFI (5 << 16)
+#define CONFIG_SYS_FSL_USB_PLLPRG2_PLL_EN (1 << 21)
+#define CONFIG_SYS_FSL_USB_SYS_CLK_VALID (1 << 0)
+#else
+struct ccsr_usb_phy {
+ u8 res0[0x18];
+ u32 usb_enable_override;
+ u8 res[0xe4];
+};
+#define CONFIG_SYS_FSL_USB_ENABLE_OVERRIDE 1
+#endif
+
+#endif /*_ASM_FSL_USB_H_ */
projects / karo-tx-uboot.git / commitdiff