Changes for U-Boot 1.1.3:
======================================================================
+* Add support for ext2 filesystems and image timestamps to TQM5200 board
+
+* Add reset code for Coral-P on INKA4x0 board
+
+* Patch by Martin Krause, 28 Jun 2004:
+ Update for TRAB board.
+
+* Fix some missing "volatile"s in MPC5xxx FEC driver
+
* Fix cirrus voltage detection (for CPC45)
* Fix byteorder problem in usbboot and scsiboot commands.
#
-# (C) Copyright 2000 - 2004
+# (C) Copyright 2000 - 2005
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
#
# See file CREDITS for list of people who contributed to this
*(vu_long *)MPC5XXX_BOOTCS_CFG &= ~0x1; /* clear RO */
}
+#define GPIO_PSC3_9 0x04000000UL
+
+int misc_init_f (void)
+{
+ /*
+ * Reset Coral-P graphics controller
+ */
+ *(vu_long *) MPC5XXX_WU_GPIO_ENABLE |= GPIO_PSC3_9;
+ *(vu_long *) MPC5XXX_WU_GPIO_DIR |= GPIO_PSC3_9;
+ *(vu_long *) MPC5XXX_WU_GPIO_DATA |= GPIO_PSC3_9;
+ return 0;
+}
+
#ifdef CONFIG_PCI
static struct pci_controller hose;
pci_mpc5xxx_init(&hose);
}
#endif
-
-
int off;
uint32_t val;
+ /* special case for prepare.img */
+ if (idx == IDX_PREPARE) {
+ /* enable the power switch */
+ *CPLD_VFD_BK &= ~POWER_OFF;
+ return 0;
+ }
+
hdr = (image_header_t *)LOAD_ADDR;
/* write the time field into EEPROM */
off = auee_off[idx].time;
#include <common.h>
#include <command.h>
#include <s3c2400.h>
+#include <rtc.h>
/*
* TRAB board specific commands. Especially commands for burn-in and function
uchar *buffer, int len);
int i2c_read_multiple (uchar chip, uint addr, int alen,
uchar *buffer, int len);
+int do_temp_log (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]);
/* helper functions */
static void adc_init (void);
led_init ();
global_vars_init ();
test_function_table_init ();
+ spi_init ();
if (global_vars_write_to_eeprom () != 0) {
printf ("%s: error writing global_vars to eeprom\n",
}
spi_init ();
- tsc2000_reg_init ();
contact_temp = tsc2000_contact_temp();
printf ("%d degree C * 100\n", contact_temp) ;
{
int contact_temp;
- spi_init ();
contact_temp = tsc2000_contact_temp ();
if ((contact_temp < MIN_CONTACT_TEMP)
return (0);
}
+int do_temp_log (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+ int contact_temp;
+ int delay = 0;
+#if (CONFIG_COMMANDS & CFG_CMD_DATE)
+ struct rtc_time tm;
+#endif
+
+ if (argc > 2) {
+ printf ("Usage:\n%s\n", cmdtp->usage);
+ return 1;
+ }
+
+ if (argc > 1) {
+ delay = simple_strtoul(argv[1], NULL, 10);
+ }
+
+ spi_init ();
+ while (1) {
+
+#if (CONFIG_COMMANDS & CFG_CMD_DATE)
+ rtc_get (&tm);
+ printf ("%4d-%02d-%02d %2d:%02d:%02d - ",
+ tm.tm_year, tm.tm_mon, tm.tm_mday,
+ tm.tm_hour, tm.tm_min, tm.tm_sec);
+#endif
+
+ contact_temp = tsc2000_contact_temp();
+ printf ("%d\n", contact_temp) ;
+
+ if (delay != 0)
+ /*
+ * reset timer to avoid timestamp overflow problem
+ * after about 68 minutes of udelay() time.
+ */
+ reset_timer_masked ();
+ sdelay (delay);
+ }
+
+ return 0;
+}
+
+U_BOOT_CMD(
+ tlog, 2, 1, do_temp_log,
+ "tlog - log contact temperature [1/100 C] to console (endlessly)\n",
+ "delay\n"
+ " - contact temperature [1/100 C] is printed endlessly to console\n"
+ " <delay> specifies the seconds to wait between two measurements\n"
+ " For each measurment a timestamp is printeted\n"
+);
+
#endif /* CFG_CMD_BSP */
#include "Pt1000_temp_data.h"
+/* helper function */
+#define abs(value) (((value) < 0) ? ((value)*-1) : (value))
+
+/*
+ * Maximal allowed deviation between two immediate meassurments of an analog
+ * thermo channel. 1 DIGIT = 0.0276 °C. This is used to filter sporadic
+ * "jumps" in measurment.
+ */
+#define MAX_DEVIATION 18 /* unit: DIGITs of adc; 18 DIGIT = 0.5 °C */
+
void spi_init(void)
{
S3C24X0_GPIO * const gpio = S3C24X0_GetBase_GPIO();
long adc_pt1000, offset;
long u_pt1000;
long contact_temp;
-
+ long temp1, temp2;
tsc2000_reg_init ();
tsc2000_set_range (3);
- adc_pt1000 = tsc2000_read_channel (14);
+ /*
+ * Because of sporadic "jumps" in the measured adc values every
+ * channel is read two times. If there is a significant difference
+ * between the two measurements, then print an error and do a third
+ * measurement, because it is very unlikely that a successive third
+ * measurement goes also wrong.
+ */
+ temp1 = tsc2000_read_channel (14);
+ temp2 = tsc2000_read_channel (14);
+ if (abs(temp2 - temp1) < MAX_DEVIATION)
+ adc_pt1000 = temp2;
+ else {
+ printf ("%s: read adc value (channel 14) exceeded max allowed "
+ "deviation: %d * 0.0276 °C\n",
+ __FUNCTION__, MAX_DEVIATION);
+ printf ("adc value 1: %ld DIGITs\nadc value 2: %ld DIGITs\n",
+ temp1, temp2);
+ adc_pt1000 = tsc2000_read_channel (14);
+ printf ("use (third read) adc value: adc_pt1000 = "
+ "%ld DIGITs\n", adc_pt1000);
+ }
debug ("read channel 14 (pt1000 adc value): %ld\n", adc_pt1000);
- offset = tsc2000_read_channel (15);
+ temp1 = tsc2000_read_channel (15);
+ temp2 = tsc2000_read_channel (15);
+ if (abs(temp2 - temp1) < MAX_DEVIATION)
+ offset = temp2;
+ else {
+ printf ("%s: read adc value (channel 15) exceeded max allowed "
+ "deviation: %d * 0.0276 °C\n",
+ __FUNCTION__, MAX_DEVIATION);
+ printf ("adc value 1: %ld DIGITs\nadc value 2: %ld DIGITs\n",
+ temp1, temp2);
+ offset = tsc2000_read_channel (15);
+ printf ("use (third read) adc value: offset = %ld DIGITs\n",
+ offset);
+ }
debug ("read channel 15 (offset): %ld\n", offset);
/*
}
/********************************************************************/
-static void mpc5xxx_fec_rbd_clean(mpc5xxx_fec_priv *fec, FEC_RBD * pRbd)
+static void mpc5xxx_fec_rbd_clean(mpc5xxx_fec_priv *fec, volatile FEC_RBD * pRbd)
{
/*
* Reset buffer descriptor as empty
/********************************************************************/
static void mpc5xxx_fec_tbd_scrub(mpc5xxx_fec_priv *fec)
{
- FEC_TBD *pUsedTbd;
+ volatile FEC_TBD *pUsedTbd;
#if (DEBUG & 0x1)
printf ("tbd_scrub: fec->cleanTbdNum = %d, fec->usedTbdIndex = %d\n",
/*
* Initialize SmartDMA parameters stored in SRAM
*/
- *(int *)FEC_TBD_BASE = (int)fec->tbdBase;
- *(int *)FEC_RBD_BASE = (int)fec->rbdBase;
- *(int *)FEC_TBD_NEXT = (int)fec->tbdBase;
- *(int *)FEC_RBD_NEXT = (int)fec->rbdBase;
+ *(volatile int *)FEC_TBD_BASE = (int)fec->tbdBase;
+ *(volatile int *)FEC_RBD_BASE = (int)fec->rbdBase;
+ *(volatile int *)FEC_TBD_NEXT = (int)fec->tbdBase;
+ *(volatile int *)FEC_RBD_NEXT = (int)fec->rbdBase;
/*
* Enable FEC-Lite controller
* 6-byte Ethernet addresses.
*/
mpc5xxx_fec_priv *fec = (mpc5xxx_fec_priv *)dev->priv;
- FEC_TBD *pTbd;
+ volatile FEC_TBD *pTbd;
#if (DEBUG & 0x20)
printf("tbd status: 0x%04x\n", fec->tbdBase[0].status);
* This command pulls one frame from the card
*/
mpc5xxx_fec_priv *fec = (mpc5xxx_fec_priv *)dev->priv;
- FEC_RBD *pRbd = &fec->rbdBase[fec->rbdIndex];
+ volatile FEC_RBD *pRbd = &fec->rbdBase[fec->rbdIndex];
unsigned long ievent;
int frame_length, len = 0;
NBUF *frame;
/* IDE */
#if defined (CONFIG_MINIFAP) || defined (CONFIG_STK52XX)
-#define ADD_IDE_CMD CFG_CMD_IDE | CFG_CMD_FAT
+#define ADD_IDE_CMD (CFG_CMD_IDE | CFG_CMD_FAT | CFG_CMD_EXT2)
#else
#define ADD_IDE_CMD 0
#endif
* Supported commands
*/
#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
- CFG_CMD_EEPROM | \
- CFG_CMD_I2C | \
+ ADD_IDE_CMD | \
ADD_PCI_CMD | \
ADD_USB_CMD | \
- CFG_CMD_POST_DIAG | \
+ CFG_CMD_ASKENV | \
CFG_CMD_DATE | \
- CFG_CMD_REGINFO | \
+ CFG_CMD_DHCP | \
+ CFG_CMD_ECHO | \
+ CFG_CMD_EEPROM | \
+ CFG_CMD_I2C | \
CFG_CMD_MII | \
CFG_CMD_PING | \
- ADD_IDE_CMD)
+ CFG_CMD_POST_DIAG | \
+ CFG_CMD_REGINFO )
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
+#define CONFIG_TIMESTAMP /* display image timestamps */
+
#if (TEXT_BASE == 0xFC000000) /* Boot low */
# define CFG_LOWBOOT 1
#endif
* (easy to change)
*/
-#define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */
-#define CONFIG_MPC5200 1 /* (more precisely an MPC5200 CPU) */
-#define CONFIG_INKA4X0 1 /* INKA4x0 board */
+#define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */
+#define CONFIG_MPC5200 1 /* (more precisely an MPC5200 CPU) */
+#define CONFIG_INKA4X0 1 /* INKA4x0 board */
-#define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
+#define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
+#define CONFIG_MISC_INIT_F 1 /* Use misc_init_f() */
+
+#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
/*
* Serial console configuration
*/
-#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
-#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
+#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
+#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
/*
*-----------------------------------------------------------------------
*/
#define CONFIG_USB_OHCI
-#define CONFIG_USB_CLOCK 0x00015555
-#define CONFIG_USB_CONFIG 0x00001000
+#define CONFIG_USB_CLOCK 0x00015555
+#define CONFIG_USB_CONFIG 0x00001000
#endif /* __CONFIG_H */
#endif /* CFG_HUSH_PARSER */
#endif /* CONFIG_FLASH_8MB */
-#if 0 /* disabled for development */
+#if 1 /* feel free to disable for development */
#define CONFIG_AUTOBOOT_KEYED /* Enable password protection */
#define CONFIG_AUTOBOOT_PROMPT "\nEnter password - autoboot in %d sec...\n"
-#define CONFIG_AUTOBOOT_DELAY_STR "system" /* 1st password */
+#define CONFIG_AUTOBOOT_DELAY_STR "R" /* 1st "password" */
#endif
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
projects / karo-tx-uboot.git / commitdiff