Changes since U-Boot 1.0.0:
======================================================================
+* Patch by Scott McNutt, 02 Jan 2004:
+ Add support for the Nios Active Serial Memory Interface (ASMI)
+ on Cyclone devices
+
+* Patch by Andrea Marson, 16 Dec 2003:
+ Add support for the PPChameleon ME and HI modules
+
+* Patch by Yuli Barcohen, 22 Dec 2003:
+ Add support for Motorola DUET ADS board (MPC87x/88x)
+
* Patch by Robert Schwebel, 15 Dec 2003:
add support for cramfs (uses JFFS2 command interface)
LIST_8xx=" \
AdderII ADS860 AMX860 c2mon \
- CCM cogent_mpc8xx ESTEEM192E ETX094 \
- ELPT860 FADS823 FADS850SAR FADS860T \
- FLAGADM FPS850L GEN860T GEN860T_SC \
- GENIETV GTH hermes IAD210 \
- ICU862_100MHz IP860 IVML24 IVML24_128 \
- IVML24_256 IVMS8 IVMS8_128 IVMS8_256 \
- KUP4K LANTEC lwmon MBX \
- MBX860T MHPC MPC86xADS MVS1 \
- NETVIA NETVIA_V2 NX823 pcu_e \
- QS823 QS850 QS860T R360MPI \
- RBC823 rmu RPXClassic RPXlite \
- RRvision SM850 SPD823TS svm_sc8xx \
- SXNI855T TOP860 TQM823L TQM823L_LCD \
- TQM850L TQM855L TQM860L v37 \
+ CCM cogent_mpc8xx DUET_ADS ESTEEM192E \
+ ETX094 ELPT860 FADS823 FADS850SAR \
+ FADS860T FLAGADM FPS850L GEN860T \
+ GEN860T_SC GENIETV GTH hermes \
+ IAD210 ICU862_100MHz IP860 IVML24 \
+ IVML24_128 IVML24_256 IVMS8 IVMS8_128 \
+ IVMS8_256 KUP4K LANTEC lwmon \
+ MBX MBX860T MHPC MPC86xADS \
+ MVS1 NETVIA NETVIA_V2 NX823 \
+ pcu_e QS823 QS850 QS860T \
+ R360MPI RBC823 rmu RPXClassic \
+ RPXlite RRvision SM850 SPD823TS \
+ svm_sc8xx SXNI855T TOP860 TQM823L \
+ TQM823L_LCD TQM850L TQM855L TQM860L \
+ v37 \
"
#########################################################################
LIBS += board/$(BOARDDIR)/lib$(BOARD).a
LIBS += cpu/$(CPU)/lib$(CPU).a
LIBS += lib_$(ARCH)/lib$(ARCH).a
-LIBS += fs/jffs2/libjffs2.a fs/fdos/libfdos.a fs/fat/libfat.a
+LIBS += fs/cramfs/libcramfs.a fs/fat/libfat.a fs/fdos/libfdos.a fs/jffs2/libjffs2.a
LIBS += net/libnet.a
LIBS += disk/libdisk.a
LIBS += rtc/librtc.a
AdderII_config: unconfig
@./mkconfig $(@:_config=) ppc mpc8xx adderII
-ADS860_config: unconfig
+ADS860_config \
+DUET_ADS_config \
+FADS823_config \
+FADS850SAR_config \
+MPC86xADS_config \
+FADS860T_config: unconfig
@./mkconfig $(@:_config=) ppc mpc8xx fads
AMX860_config : unconfig
ETX094_config : unconfig
@./mkconfig $(@:_config=) ppc mpc8xx etx094
-FADS823_config \
-FADS850SAR_config \
-MPC86xADS_config \
-FADS860T_config: unconfig
- @./mkconfig $(@:_config=) ppc mpc8xx fads
-
FLAGADM_config: unconfig
@./mkconfig $(@:_config=) ppc mpc8xx flagadm
- board/Marvell/db64460 Files specific to db64460 board
- board/mbx8xx Files specific to MBX boards
- board/mpc8260ads
- Files specific to MPC8260ADS and PQ2FADS-ZU boards
+ Files specific to MPC826xADS and PQ2FADS-ZU/VR boards
- board/mpc8540ads
Files specific to MPC8540ADS boards
- board/mpc8560ads
CONFIG_NETVIA, CONFIG_RBC823, CONFIG_ZPC1900,
CONFIG_MPC8540ADS, CONFIG_MPC8560ADS, CONFIG_QS850,
CONFIG_QS823, CONFIG_QS860T, CONFIG_DB64360,
- CONFIG_DB64460
+ CONFIG_DB64460, CONFIG_DUET_ADS
ARM based boards:
-----------------
CONFIG_ADSTYPE
Possible values are:
CFG_8260ADS - original MPC8260ADS
- CFG_8266ADS - MPC8266ADS (untested)
+ CFG_8266ADS - MPC8266ADS
CFG_PQ2FADS - PQ2FADS-ZU or PQ2FADS-VR
at91rm9200dk_config omap1510inn_config MPC8260ADS_config
omap1610inn_config ZPC1900_config MPC8540ADS_config
MPC8560ADS_config QS850_config QS823_config
- QS860T_config
+ QS860T_config DUET_ADS_config
Note: for some board special configuration names may exist; check if
additional information is available from the board vendor; for
in Assembler); no C++ is used, so please do not use C++ style
comments (//) in your code.
+Please also stick to the following formatiing rules:
+- remove any trailing white space
+- use TAB characters for indentation, not spaces
+- make sure NOT to use DOS '\r\n' line feeds
+- do not add more than 2 empty lines to source files
+- do not add trailing empty lines to source files
+
Submissions which do not conform to the standards may be returned
with a request to reformat the changes.
/*
- * (C) Copyright 2001-2003
- * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
+ * (C) Copyright 2003
+ * DAVE Srl
+ * http://www.dave-tech.it
+ * http://www.wawnet.biz
+ * mailto:info@wawnet.biz
*
* See file CREDITS for list of people who contributed to this
* project.
#
-# (C) Copyright 2000
+# (C) Copyright 2000-2004
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
#
+# Modified by, Yuli Barcohen, Arabella Software Ltd., yuli@arabellasw.com
+#
# See file CREDITS for list of people who contributed to this
# project.
#
#
#
-# Motorola old MPC821/860ADS, MPC8xxFADS, and new MPC866ADS boards
+# Motorola old MPC821/860ADS, MPC8xxFADS, new MPC866ADS, and DUET
+# (MPC87x/88x) ADS boards
#
TEXT_BASE = 0xFE000000
-#TEXT_BASE = 0x02800000
-#OBJCFLAGS = --set-section-flags=.ppcenv=contents,alloc,load,data
+PLATFORM_CPPFLAGS += -I$(TOPDIR)/board/fads
+HOST_CFLAGS += -I$(TOPDIR)/board/fads
+HOST_ENVIRO_CFLAGS += -I$(TOPDIR)/board/fads
/*
- * (C) Copyright 2000
+ * (C) Copyright 2000-2004
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
+ * Modified by, Yuli Barcohen, Arabella Software Ltd., yuli@arabellasw.com
+ *
* See file CREDITS for list of people who contributed to this
* project.
*
* MA 02111-1307 USA
*/
-#include <common.h>
#include <config.h>
+#include <common.h>
#include <mpc8xx.h>
-#include "fads.h"
-
-/* ------------------------------------------------------------------------- */
#define _NOT_USED_ 0xFFFFFFFF
+/* ========================================================================= */
+
+#ifndef CONFIG_DUET_ADS /* No old DRAM on Duet */
+
#if defined(CONFIG_DRAM_50MHZ)
/* 50MHz tables */
static const uint dram_60ns[] =
#error dram not correctly defined - use CONFIG_DRAM_25MHZ or CONFIG_DRAM_50MHZ
#endif
-/* ------------------------------------------------------------------------- */
-
-
-/*
- * Check Board Identity:
- */
-
-#if defined(CONFIG_FADS) && !defined(CONFIG_MPC86xADS)
-static void checkdboard(void)
-{
- /* get db type from BCSR 3 */
- uint k = (*((uint *)BCSR3) >> 24) & 0x3f;
-
- printf(" with db ");
-
- switch(k) {
- case 0x03 :
- puts ("MPC823");
- break;
- case 0x20 :
- puts ("MPC801");
- break;
- case 0x21 :
- puts ("MPC850");
- break;
- case 0x22 :
- puts ("MPC821, MPC860 / MPC860SAR / MPC860T");
- break;
- case 0x23 :
- puts ("MPC860SAR");
- break;
- case 0x24 :
- case 0x2A :
- puts ("MPC860T");
- break;
- case 0x3F :
- puts ("MPC850SAR");
- break;
- default : printf("0x%x", k);
- }
-}
-#endif /* defined(CONFIG_FADS) && !defined(CONFIG_MPC86xADS) */
-
-int checkboard (void)
-{
- /* get revision from BCSR 3 */
- uint r = (((*((uint *) BCSR3) >> 23) & 1) << 3)
- | (((*((uint *) BCSR3) >> 19) & 1) << 2)
- | (((*((uint *) BCSR3) >> 16) & 3));
-
- puts ("Board: ");
-
-#ifdef CONFIG_FADS
-# ifdef CONFIG_MPC86xADS
- puts ("MPC86xADS");
-# else
- puts ("FADS");
- checkdboard ();
-# endif /* !CONFIG_MPC86xADS */
- printf (" rev ");
-
- switch (r) {
- case 0x00:
- puts ("ENG\n");
- break;
- case 0x01:
- puts ("PILOT\n");
- break;
- default:
- printf ("unknown (0x%x)\n", r);
- return (-1);
- }
-#endif /* CONFIG_FADS */
-
-#ifdef CONFIG_ADS
- printf ("ADS rev ");
-
- switch (r) {
- case 0x00:
- puts ("ENG - this board sucks, check the errata, not supported\n");
- return -1;
- case 0x01:
- puts ("PILOT - warning, read errata \n");
- break;
- case 0x02:
- puts ("A - warning, read errata \n");
- break;
- case 0x03:
- puts ("B \n");
- break;
- default:
- printf ("unknown revision (0x%x)\n", r);
- return (-1);
- }
-#endif /* CONFIG_ADS */
-
- return 0;
-}
-
/* ------------------------------------------------------------------------- */
static long int dram_size (long int *base, long int maxsize)
{
/* maybe we should turn off upma here or something */
}
+#endif /* !CONFIG_DUET_ADS */
-#ifdef CONFIG_FADS
-/* SDRAM SUPPORT (FADS ONLY) */
+/* ========================================================================= */
+
+#ifdef CONFIG_FADS /* SDRAM exists on FADS and newer boards */
#if defined(CONFIG_SDRAM_100MHZ)
}
}
-/* SDRAM SUPPORT (FADS ONLY) */
#endif /* CONFIG_FADS */
+/* ========================================================================= */
+
long int initdram (int board_type)
{
uint sdramsz = 0; /* size of sdram in Mbytes */
uint base = 0; /* base of dram in bytes */
uint m = 0; /* size of dram in Mbytes */
+#ifndef CONFIG_DUET_ADS
uint k, s;
+#endif
#ifdef CONFIG_FADS
if (!initsdram (0x00000000, &sdramsz)) {
printf ("(%u MB SDRAM) ", sdramsz);
}
#endif
-
+#ifndef CONFIG_DUET_ADS /* No old DRAM on Duet */
k = (*((uint *) BCSR2) >> 23) & 0x0f;
switch (k & 0x3) {
_dramdisable ();
m = 0;
}
-
+#endif /* !CONFIG_DUET_ADS */
m += sdramsz; /* add sdram size to total */
- if (!m) {
- /********************************
- *DRAM ERROR, HALT PROCESSOR
- *********************************/
- while (1);
- return -1;
- }
-
return (m << 20);
}
return (0);
}
+/* ========================================================================= */
+
+/*
+ * Check Board Identity:
+ */
+
+#if defined(CONFIG_FADS) && defined(CFG_DAUGHTERBOARD)
+static void checkdboard(void)
+{
+ /* get db type from BCSR 3 */
+ uint k = (*((uint *)BCSR3) >> 24) & 0x3f;
+
+ puts (" with db ");
+
+ switch(k) {
+ case 0x03 :
+ puts ("MPC823");
+ break;
+ case 0x20 :
+ puts ("MPC801");
+ break;
+ case 0x21 :
+ puts ("MPC850");
+ break;
+ case 0x22 :
+ puts ("MPC821, MPC860 / MPC860SAR / MPC860T");
+ break;
+ case 0x23 :
+ puts ("MPC860SAR");
+ break;
+ case 0x24 :
+ case 0x2A :
+ puts ("MPC860T");
+ break;
+ case 0x3F :
+ puts ("MPC850SAR");
+ break;
+ default : printf("0x%x", k);
+ }
+}
+#endif /* defined(CONFIG_FADS) && defined(CFG_DAUGHTERBOARD) */
+
+int checkboard (void)
+{
+ /* get revision from BCSR 3 */
+ uint r = (((*((uint *) BCSR3) >> 23) & 1) << 3)
+ | (((*((uint *) BCSR3) >> 19) & 1) << 2)
+ | (((*((uint *) BCSR3) >> 16) & 3));
+
+ puts ("Board: ");
+
+#if defined(CONFIG_MPC86xADS)
+ puts ("MPC86xADS");
+#elif defined(CONFIG_DUET_ADS)
+ puts ("DUET ADS");
+ r = 0; /* I've got NR (No Revision) board */
+#elif defined(CONFIG_FADS)
+ puts ("FADS");
+ checkdboard ();
+#else
+ puts ("ADS");
+#endif
+ puts (" rev ");
+
+ switch (r) {
+#if defined(CONFIG_ADS)
+ case 0x00:
+ puts ("ENG - this board sucks, check the errata, not supported\n");
+ return -1;
+ case 0x01:
+ puts ("PILOT - warning, read errata \n");
+ break;
+ case 0x02:
+ puts ("A - warning, read errata \n");
+ break;
+ case 0x03:
+ puts ("B \n");
+ break;
+#elif defined(CONFIG_DUET_ADS)
+ case 0x00:
+ puts ("NR\n");
+ break;
+#else /* FADS and newer */
+ case 0x00:
+ puts ("ENG\n");
+ break;
+ case 0x01:
+ puts ("PILOT\n");
+ break;
+#endif /* CONFIG_ADS */
+ default:
+ printf ("unknown (0x%x)\n", r);
+ return -1;
+ }
+
+ return 0;
+}
+
+/* ========================================================================= */
#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
#endif /* CFG_CMD_PCMCIA */
-/* ------------------------------------------------------------------------- */
+/* ========================================================================= */
#ifdef CFG_PC_IDE_RESET
}
#endif /* CFG_PC_IDE_RESET */
-/* ------------------------------------------------------------------------- */
/*
- * (C) Copyright 2000
+ * (C) Copyright 2000-2004
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
+ * Derived from FADS860T definitions by Magnus Damm, Helmut Buchsbaum,
+ * and Dan Malek
+ *
+ * Modified by, Yuli Barcohen, Arabella Software Ltd., yuli@arabellasw.com
+ *
+ * This header file contains values common to all FADS family boards.
+ *
* See file CREDITS for list of people who contributed to this
* project.
*
*/
/****************************************************************************
- * FLASH Memory Map as used by FADS Monitor:
+ * Flash Memory Map as used by U-Boot:
*
* Start Address Length
* +-----------------------+ 0xFE00_0000 Start of Flash -----------------
- * | MON8xx code | 0xFE00_0100 Reset Vector
- * +-----------------------+ 0xFE0?_????
- * | (unused) |
- * +-----------------------+ 0xFE01_FF00
- * | Ethernet Addresses | 0x78
- * +-----------------------+ 0xFE01_FF78
- * | (Reserved for MON8xx) | 0x44
- * +-----------------------+ 0xFE01_FFBC
- * | Lock Address | 0x04
- * +-----------------------+ 0xFE01_FFC0 ^
- * | Hardware Information | 0x40 | MON8xx
- * +=======================+ 0xFE02_0000 (sector border) -----------------
- * | Autostart Header | | Applications
+ * | | 0xFE00_0100 Reset Vector
+ * + + 0xFE0?_????
+ * | U-Boot code |
+ * | |
+ * +-----------------------+ 0xFE04_0000 (sector border)
+ * | |
+ * | |
+ * | U-Boot environment |
+ * | | ^
+ * | | | U-Boot
+ * +=======================+ 0xFE08_0000 (sector border) -----------------
+ * | Available | | Applications
* | ... | v
*
*****************************************************************************/
+/* should ALWAYS define this, measure_gclk in speed.c is unreliable */
+/* in general, we always know this for FADS+new ADS anyway */
+#define CONFIG_8xx_GCLK_FREQ ((CFG_8XX_XIN) * (CFG_8XX_FACT))
+
+#if 0
+#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
+#else
+#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+#endif
+
+#undef CONFIG_BOOTARGS
+#define CONFIG_BOOTCOMMAND \
+ "dhcp;" \
+ "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
+ "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \
+ "bootm"
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+/*
+ * New MPC86xADS and Duet provide two Ethernet connectivity options:
+ * 10Mbit/s on SCC and 100Mbit/s on FEC. FADS provides SCC Ethernet on
+ * motherboard and FEC Ethernet on daughterboard. All new PQ1 chips have
+ * got FEC so FEC is the default.
+ */
+#ifndef CONFIG_ADS
+#undef CONFIG_SCC1_ENET /* Disable SCC1 ethernet */
+#define CONFIG_FEC_ENET /* Use FEC ethernet */
+#else /* Old ADS has not got FEC option */
+#define CONFIG_SCC1_ENET /* Use SCC1 ethernet */
+#undef CONFIG_FEC_ENET /* No FEC ethernet */
+#endif /* !CONFIG_ADS */
+
+#if defined(CONFIG_SCC1_ENET) && defined(CONFIG_FEC_ENET)
+#error Both CONFIG_SCC1_ENET and CONFIG_FEC_ENET configured
+#endif
+
+#ifdef CONFIG_FEC_ENET
+#define CFG_DISCOVER_PHY
+#endif
+
+#ifndef CONFIG_COMMANDS
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
+ | CFG_CMD_DHCP \
+ | CFG_CMD_IMMAP \
+ | CFG_CMD_MII \
+ | CFG_CMD_PING \
+ )
+#endif /* !CONFIG_COMMANDS */
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*
+ * Miscellaneous configurable options
+ */
+#undef CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=>" /* Monitor Command Prompt */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_LOAD_ADDR 0x00100000
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CFG_IMMR 0xFF000000
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR CFG_IMMR
+#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
+#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE 0x00000000
+#if defined(CONFIG_MPC86xADS) || defined(CONFIG_DUET_ADS) /* New ADS or Duet */
+#define CFG_SDRAM_SIZE 0x00800000 /* 8 Mbyte */
+#elif defined(CONFIG_FADS) /* Old/new FADS */
+#define CFG_SDRAM_SIZE 0x00400000 /* 4 Mbyte */
+#else /* Old ADS */
+#define CFG_SDRAM_SIZE 0x00000000 /* No SDRAM */
+#endif
+
+#define CFG_MEMTEST_START 0x0100000 /* memtest works on */
+#if (CFG_SDRAM_SIZE)
+#define CFG_MEMTEST_END CFG_SDRAM_SIZE /* 1 ... SDRAM_SIZE */
+#else
+#define CFG_MEMTEST_END 0x0400000 /* 1 ... 4 MB in DRAM */
+#endif /* CFG_SDRAM_SIZE */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+/*-----------------------------------------------------------------------
+ * Flash organization
+ */
+#define CFG_FLASH_BASE TEXT_BASE
+#define CFG_FLASH_SIZE ((uint)(8 * 1024 * 1024)) /* max 8Mbyte */
+
+#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 16 /* max number of sectors on one chip */
+
+#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_SECT_SIZE 0x40000 /* see README - env sector total size */
+#define CFG_ENV_OFFSET CFG_ENV_SECT_SIZE
+#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment */
+
+#define CFG_MONITOR_BASE CFG_FLASH_BASE
+#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 KB for monitor */
+#define CFG_MALLOC_LEN (384 << 10) /* Reserve 384 kB for malloc() */
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
+#endif
+
+/*-----------------------------------------------------------------------
+ * I2C configuration
+ */
+#if (CONFIG_COMMANDS & CFG_CMD_I2C)
+#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
+#define CFG_I2C_SPEED 400000 /* I2C speed and slave address defaults */
+#define CFG_I2C_SLAVE 0x7F
+#endif
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control 11-9
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
+ */
+#if defined(CONFIG_WATCHDOG)
+#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
+ SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
+#else
+#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
+#endif
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration 11-6
+ *-----------------------------------------------------------------------
+ * PCMCIA config., multi-function pin tri-state
+ */
+#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
+
+/*-----------------------------------------------------------------------
+ * TBSCR - Time Base Status and Control 11-26
+ *-----------------------------------------------------------------------
+ * Clear Reference Interrupt Status, Timebase freezing enabled
+ */
+#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBE)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control 11-31
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
+ */
+#define CFG_PISCR (PISCR_PS | PISCR_PITF)
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock and reset Control Register 15-27
+ *-----------------------------------------------------------------------
+ * Set clock output, timebase and RTC source and divider,
+ * power management and some other internal clocks
+ */
+#define SCCR_MASK SCCR_EBDF11
+#define CFG_SCCR (SCCR_TBS|SCCR_COM00|SCCR_DFSYNC00|SCCR_DFBRG00|SCCR_DFNL000|SCCR_DFNH000|SCCR_DFLCD000|SCCR_DFALCD00)
+
+ /*-----------------------------------------------------------------------
+ *
+ *-----------------------------------------------------------------------
+ *
+ */
+#define CFG_DER 0
+
+/* Because of the way the 860 starts up and assigns CS0 the
+* entire address space, we have to set the memory controller
+* differently. Normally, you write the option register
+* first, and then enable the chip select by writing the
+* base register. For CS0, you must write the base register
+* first, followed by the option register.
+*/
+
+/*
+ * Init Memory Controller:
+ *
+ * BR0/OR0 (Flash)
+ * BR1/OR1 (BCSR)
+ */
+/* the other CS:s are determined by looking at parameters in BCSRx */
+
+#define BCSR_ADDR ((uint) 0xFF080000)
+
+#define CFG_PRELIM_OR_AM 0xFF800000 /* OR addr mask */
+
+/* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0 */
+#define CFG_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK | OR_TRLX)
+
+#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH) /* 8 Mbyte until detected */
+#define CFG_BR0_PRELIM ((CFG_FLASH_BASE & BR_BA_MSK) | BR_V )
+
+/* BCSRx - Board Control and Status Registers */
+#define CFG_OR1_PRELIM 0xFFFF8110 /* 64Kbyte address space */
+#define CFG_BR1_PRELIM ((BCSR_ADDR) | BR_V)
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+/* values according to the manual */
+
+#define PCMCIA_MEM_ADDR ((uint)0xFF020000)
+#define PCMCIA_MEM_SIZE ((uint)(64 * 1024))
+
+#define BCSR0 ((uint) (BCSR_ADDR + 0x00))
+#define BCSR1 ((uint) (BCSR_ADDR + 0x04))
+#define BCSR2 ((uint) (BCSR_ADDR + 0x08))
+#define BCSR3 ((uint) (BCSR_ADDR + 0x0c))
+#define BCSR4 ((uint) (BCSR_ADDR + 0x10))
+
+/*
+ * (F)ADS bitvalues by Helmut Buchsbaum
+ *
+ * See User's Manual for a proper
+ * description of the following structures
+ */
+
+#define BCSR0_ERB ((uint)0x80000000)
+#define BCSR0_IP ((uint)0x40000000)
+#define BCSR0_BDIS ((uint)0x10000000)
+#define BCSR0_BPS_MASK ((uint)0x0C000000)
+#define BCSR0_ISB_MASK ((uint)0x01800000)
+#define BCSR0_DBGC_MASK ((uint)0x00600000)
+#define BCSR0_DBPC_MASK ((uint)0x00180000)
+#define BCSR0_EBDF_MASK ((uint)0x00060000)
+
+#define BCSR1_FLASH_EN ((uint)0x80000000)
+#define BCSR1_DRAM_EN ((uint)0x40000000)
+#define BCSR1_ETHEN ((uint)0x20000000)
+#define BCSR1_IRDEN ((uint)0x10000000)
+#define BCSR1_FLASH_CFG_EN ((uint)0x08000000)
+#define BCSR1_CNT_REG_EN_PROTECT ((uint)0x04000000)
+#define BCSR1_BCSR_EN ((uint)0x02000000)
+#define BCSR1_RS232EN_1 ((uint)0x01000000)
+#define BCSR1_PCCEN ((uint)0x00800000)
+#define BCSR1_PCCVCC0 ((uint)0x00400000)
+#define BCSR1_PCCVPP_MASK ((uint)0x00300000)
+#define BCSR1_DRAM_HALF_WORD ((uint)0x00080000)
+#define BCSR1_RS232EN_2 ((uint)0x00040000)
+#define BCSR1_SDRAM_EN ((uint)0x00020000)
+#define BCSR1_PCCVCC1 ((uint)0x00010000)
+
+#define BCSR1_PCCVCCON BCSR1_PCCVCC0
+
+#define BCSR2_FLASH_PD_MASK ((uint)0xF0000000)
+#define BCSR2_DRAM_PD_MASK ((uint)0x07800000)
+#define BCSR2_DRAM_PD_SHIFT 23
+#define BCSR2_EXTTOLI_MASK ((uint)0x00780000)
+#define BCSR2_DBREVNR_MASK ((uint)0x00030000)
+
+#define BCSR3_DBID_MASK ((ushort)0x3800)
+#define BCSR3_CNT_REG_EN_PROTECT ((ushort)0x0400)
+#define BCSR3_BREVNR0 ((ushort)0x0080)
+#define BCSR3_FLASH_PD_MASK ((ushort)0x0070)
+#define BCSR3_BREVN1 ((ushort)0x0008)
+#define BCSR3_BREVN2_MASK ((ushort)0x0003)
+
+#define BCSR4_ETHLOOP ((uint)0x80000000)
+#define BCSR4_TFPLDL ((uint)0x40000000)
+#define BCSR4_TPSQEL ((uint)0x20000000)
+#define BCSR4_SIGNAL_LAMP ((uint)0x10000000)
+#define BCSR4_FETH_EN ((uint)0x08000000)
+#define BCSR4_FETHCFG0 ((uint)0x04000000)
+#define BCSR4_FETHFDE ((uint)0x02000000)
+#define BCSR4_FETHCFG1 ((uint)0x00400000)
+#define BCSR4_FETHRST ((uint)0x00200000)
+
+#ifdef CONFIG_MPC823
+#define BCSR4_USB_EN ((uint)0x08000000)
+#endif /* CONFIG_MPC823 */
+#ifdef CONFIG_MPC860SAR
+#define BCSR4_UTOPIA_EN ((uint)0x08000000)
+#endif /* CONFIG_MPC860SAR */
+#ifdef CONFIG_MPC860T
+#define BCSR4_FETH_EN ((uint)0x08000000)
+#endif /* CONFIG_MPC860T */
+#ifdef CONFIG_MPC823
+#define BCSR4_USB_SPEED ((uint)0x04000000)
+#endif /* CONFIG_MPC823 */
+#ifdef CONFIG_MPC860T
+#define BCSR4_FETHCFG0 ((uint)0x04000000)
+#endif /* CONFIG_MPC860T */
+#ifdef CONFIG_MPC823
+#define BCSR4_VCCO ((uint)0x02000000)
+#endif /* CONFIG_MPC823 */
+#ifdef CONFIG_MPC860T
+#define BCSR4_FETHFDE ((uint)0x02000000)
+#endif /* CONFIG_MPC860T */
+#ifdef CONFIG_MPC823
+#define BCSR4_VIDEO_ON ((uint)0x00800000)
+#endif /* CONFIG_MPC823 */
+#ifdef CONFIG_MPC823
+#define BCSR4_VDO_EKT_CLK_EN ((uint)0x00400000)
+#endif /* CONFIG_MPC823 */
+#ifdef CONFIG_MPC860T
+#define BCSR4_FETHCFG1 ((uint)0x00400000)
+#endif /* CONFIG_MPC860T */
+#ifdef CONFIG_MPC823
+#define BCSR4_VIDEO_RST ((uint)0x00200000)
+#endif /* CONFIG_MPC823 */
+#ifdef CONFIG_MPC860T
+#define BCSR4_FETHRST ((uint)0x00200000)
+#endif /* CONFIG_MPC860T */
+#ifdef CONFIG_MPC823
+#define BCSR4_MODEM_EN ((uint)0x00100000)
+#endif /* CONFIG_MPC823 */
+#ifdef CONFIG_MPC823
+#define BCSR4_DATA_VOICE ((uint)0x00080000)
+#endif /* CONFIG_MPC823 */
+#ifdef CONFIG_MPC850
+#define BCSR4_DATA_VOICE ((uint)0x00080000)
+#endif /* CONFIG_MPC850 */
+
+/* We don't use the 8259.
+*/
+#define NR_8259_INTS 0
+
+/* Machine type
+*/
+#define _MACH_8xx (_MACH_fads)
+
+/*-----------------------------------------------------------------------
+ * PCMCIA stuff
+ *-----------------------------------------------------------------------
+ */
+#if !defined(CONFIG_MPC823) && !defined(CONFIG_MPC850)
+#define PCMCIA_SLOT_A 1
+#endif
+
+#define CFG_PCMCIA_MEM_ADDR (0xE0000000)
+#define CFG_PCMCIA_MEM_SIZE ( 64 << 20 )
+#define CFG_PCMCIA_DMA_ADDR (0xE4000000)
+#define CFG_PCMCIA_DMA_SIZE ( 64 << 20 )
+#define CFG_PCMCIA_ATTRB_ADDR (0xE8000000)
+#define CFG_PCMCIA_ATTRB_SIZE ( 64 << 20 )
+#define CFG_PCMCIA_IO_ADDR (0xEC000000)
+#define CFG_PCMCIA_IO_SIZE ( 64 << 20 )
+
+/*-----------------------------------------------------------------------
+ * IDE/ATA stuff
+ *-----------------------------------------------------------------------
+ */
+#define CONFIG_MAC_PARTITION 1
+#define CONFIG_DOS_PARTITION 1
+#define CONFIG_ISO_PARTITION 1
+
+#undef CONFIG_ATAPI
+#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
+#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
+#undef CONFIG_IDE_LED /* LED for ide not supported */
+#undef CONFIG_IDE_RESET /* reset for ide not supported */
+
+#define CFG_IDE_MAXBUS 1 /* max. 2 IDE busses */
+#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*2) /* max. 2 drives per IDE bus */
+
+#define CFG_ATA_BASE_ADDR CFG_PCMCIA_MEM_ADDR
+#define CFG_ATA_IDE0_OFFSET 0x0000
+
+/* Offset for data I/O */
+#define CFG_ATA_DATA_OFFSET (CFG_PCMCIA_MEM_SIZE + 0x320)
+/* Offset for normal register accesses */
+#define CFG_ATA_REG_OFFSET (2 * CFG_PCMCIA_MEM_SIZE + 0x320)
+/* Offset for alternate registers */
+#define CFG_ATA_ALT_OFFSET 0x0000
+
+#define CONFIG_DISK_SPINUP_TIME 1000000
+#undef CONFIG_DISK_SPINUP_TIME /* usin´ Compact Flash */
#include <cramfs/cramfs_fs.h>
+extern int cramfs_check (struct part_info *info);
+extern int cramfs_load (char *loadoffset, struct part_info *info, char *filename);
+extern int cramfs_ls (struct part_info *info, char *filename);
+extern int cramfs_info (struct part_info *info);
+
static int part_num=0;
#ifndef CFG_JFFS_CUSTOM_PART
#if ((defined(CONFIG_MPC86x) || defined(CONFIG_MPC855)) && \
!defined(CONFIG_MPC862))
+static int check_CPU (long clock, uint pvr, uint immr)
+{
+ char *id_str =
# if defined(CONFIG_MPC855)
-# define ID_STR "PC855"
-# elif defined(CONFIG_MPC852T)
-# define ID_STR "PC852T"
-# elif defined(CONFIG_MPC859T)
-# define ID_STR "PC859T"
-# elif defined(CONFIG_MPC859DSL)
-# define ID_STR "PC859DSL"
+ "PC855";
# elif defined(CONFIG_MPC860P)
-# define ID_STR "PC860P"
-# elif defined(CONFIG_MPC866T)
-# define ID_STR "PC866T"
+ "PC860P";
# else
-# define ID_STR "PC86x" /* unknown 86x chip */
+ NULL;
# endif
-
-static int check_CPU (long clock, uint pvr, uint immr)
-{
volatile immap_t *immap = (immap_t *) (immr & 0xFFFF0000);
uint k, m;
char buf[32];
k = (immr << 16) | *((ushort *) & immap->im_cpm.cp_dparam[0xB0]);
m = 0;
+ /*
+ * Some boards use sockets so different CPUs can be used.
+ * We have to check chip version in run time.
+ */
switch (k) {
-#ifdef CONFIG_MPC866_et_al
- /* MPC866P/MPC866T/MPC859T/MPC859DSL/MPC852T */
- case 0x08000003: pre = 'M'; suf = ""; m = 1; break;
-#else
- case 0x00020001: pre = 'p'; suf = ""; break;
+ case 0x00020001: pre = 'P'; suf = ""; break;
case 0x00030001: suf = ""; break;
case 0x00120003: suf = "A"; break;
case 0x00130003: suf = "A3"; break;
case 0x00310065: mid = "SR"; suf = "C1"; m = 1; break;
case 0x05010000: suf = "D3"; m = 1; break;
case 0x05020000: suf = "D4"; m = 1; break;
- case 0x08000003: suf = ""; m = 1; break;
/* this value is not documented anywhere */
case 0x40000000: pre = 'P'; suf = "D"; m = 1; break;
-#endif
+ /* MPC866P/MPC866T/MPC859T/MPC859DSL/MPC852T */
+ case 0x08000003: pre = 'M'; suf = ""; m = 1;
+ if (id_str == NULL)
+ id_str =
+# if defined(CONFIG_MPC852T)
+ "PC852T";
+# elif defined(CONFIG_MPC859T)
+ "PC859T";
+# elif defined(CONFIG_MPC859DSL)
+ "PC859DSL";
+# elif defined(CONFIG_MPC866T)
+ "PC866T";
+# else
+ "PC866x"; /* Unknown chip from MPC866 family */
+# endif
+ break;
+ case 0x09000000: pre = 'M'; mid = suf = ""; m = 1;
+ if (id_str == NULL)
+ id_str = "PC885"; /* 870/875/880/885 */
+ break;
default: suf = NULL; break;
}
+ if (id_str == NULL)
+ id_str = "PC86x"; /* Unknown 86x chip */
if (suf)
- printf ("%c" ID_STR "%sZPnn%s", pre, mid, suf);
+ printf ("%c%s%sZPnn%s", pre, id_str, mid, suf);
else
- printf ("unknown M" ID_STR " (0x%08x)", k);
+ printf ("unknown M%s (0x%08x)", id_str, k);
printf (" at %s MHz:", strmhz (buf, clock));
/*
* Get timebase clock frequency (like cpu_clk in Hz)
*
- * See table 15-5 pp. 15-16, and SCCR[RTSEL] pp. 15-27.
+ * See sections 14.2 and 14.6 of the User's Manual
*/
unsigned long get_tbclk (void)
{
DECLARE_GLOBAL_DATA_PTR;
- volatile immap_t *immr = (volatile immap_t *) CFG_IMMR;
- ulong oscclk, factor;
+ uint immr = get_immr (0); /* Return full IMMR contents */
+ volatile immap_t *immap = (volatile immap_t *)(immr & 0xFFFF0000);
+ ulong oscclk, factor, pll;
- if (immr->im_clkrst.car_sccr & SCCR_TBS) {
+ if (immap->im_clkrst.car_sccr & SCCR_TBS) {
return (gd->cpu_clk / 16);
}
-#define PLPRCR_val(a) (((CFG_PLPRCR) & PLPRCR_ ## a ## _MSK) >> PLPRCR_ ## a ## _SHIFT)
-#ifdef CONFIG_MPC866_et_al
- /* MFN
- MFI + -------
- MFD + 1
- factor = -----------------
- (PDF + 1) * 2^S
- */
- factor = (PLPRCR_val(MFI) + PLPRCR_val(MFN)/(PLPRCR_val(MFD)+1))/
- (PLPRCR_val(PDF)+1) / (1<<PLPRCR_val(S));
-#else
- factor = PLPRCR_val(MF)+1;
-#endif
+ pll = immap->im_clkrst.car_plprcr;
+
+#define PLPRCR_val(a) ((pll & PLPRCR_ ## a ## _MSK) >> PLPRCR_ ## a ## _SHIFT)
+
+ /*
+ * For newer PQ1 chips (MPC866/87x/88x families), PLL multiplication
+ * factor is calculated as follows:
+ *
+ * MFN
+ * MFI + -------
+ * MFD + 1
+ * factor = -----------------
+ * (PDF + 1) * 2^S
+ *
+ * For older chips, it's just MF field of PLPRCR plus one.
+ */
+ if ((immr & 0xFFFF) >= MPC8xx_NEW_CLK) { /* MPC866/87x/88x series */
+ factor = (PLPRCR_val(MFI) + PLPRCR_val(MFN)/(PLPRCR_val(MFD)+1))/
+ (PLPRCR_val(PDF)+1) / (1<<PLPRCR_val(S));
+ } else {
+ factor = PLPRCR_val(MF)+1;
+ }
oscclk = gd->cpu_clk / factor;
- if ((immr->im_clkrst.car_sccr & SCCR_RTSEL) == 0 || factor > 2) {
+ if ((immap->im_clkrst.car_sccr & SCCR_RTSEL) == 0 || factor > 2) {
return (oscclk / 4);
}
return (oscclk / 16);
{
#ifndef CONFIG_MBX
volatile memctl8xx_t *memctl = &immr->im_memctl;
+ ulong mfmask;
#endif
ulong reg;
/* If CFG_PLPRCR (set in the various *_config.h files) tries to
* set the MF field, then just copy CFG_PLPRCR over car_plprcr,
- * otherwise OR in CFG_PLPRCR so we do not change the currentMF
+ * otherwise OR in CFG_PLPRCR so we do not change the current MF
* field value.
+ *
+ * For newer (starting MPC866) chips PLPRCR layout is different.
*/
-#if ((CFG_PLPRCR & PLPRCR_MF_MSK) != 0)
- reg = CFG_PLPRCR; /* reset control bits */
-#else
- reg = immr->im_clkrst.car_plprcr;
- reg &= PLPRCR_MF_MSK; /* isolate MF field */
- reg |= CFG_PLPRCR; /* reset control bits */
-#endif
+ if (get_immr(0xFFFF) >= MPC8xx_NEW_CLK)
+ mfmask = PLPRCR_MFACT_MSK;
+ else
+ mfmask = PLPRCR_MF_MSK;
+
+ if ((CFG_PLPRCR & mfmask) != 0)
+ reg = CFG_PLPRCR; /* reset control bits */
+ else {
+ reg = immr->im_clkrst.car_plprcr;
+ reg &= mfmask; /* isolate MF-related fields */
+ reg |= CFG_PLPRCR; /* reset control bits */
+ }
immr->im_clkrst.car_plprcr = reg;
/*
volatile immap_t *immr = (immap_t *) CFG_IMMR;
volatile fec_t *fecp = &(immr->im_cpm.cp_fec);
-#if defined(CONFIG_FADS) && \
- ( defined(CONFIG_MPC860T) || defined(CONFIG_MPC866_et_al) )
+#if defined(CONFIG_FADS) /* FADS family uses FPGA (BCSR) to control PHYs */
+#if defined(CONFIG_DUET_ADS)
+ *(vu_char *)BCSR5 &= ~(BCSR5_MII1_EN | BCSR5_MII1_RST);
+#else
/* configure FADS for fast (FEC) ethernet, half-duplex */
/* The LXT970 needs about 50ms to recover from reset, so
* wait for it by discovering the PHY before leaving eth_init().
*bcsr4 |= BCSR4_FETHRST;
udelay (10);
}
-#endif
+#endif /* CONFIG_DUET_ADS */
+#endif /* CONFIG_FADS */
/* Whack a reset.
* A delay is required between a reset of the FEC block and
* initialization of other FEC registers because the reset takes
*/
fecp->fec_mii_speed = ((bd->bi_intfreq + 4999999) / 5000000) << 1;
-#if !defined(CONFIG_ICU862) && !defined(CONFIG_IAD210)
+#if defined(CONFIG_DUET) /* MPC87x/88x have got 2 FECs and different pinout */
+ immr->im_ioport.iop_papar |= 0xf830;
+ immr->im_ioport.iop_padir |= 0x0830;
+ immr->im_ioport.iop_padir &= ~0xf000;
+ immr->im_cpm.cp_pbpar |= 0x00001001;
+ immr->im_cpm.cp_pbdir &= ~0x00001001;
+ immr->im_ioport.iop_pcpar |= 0x000c;
+ immr->im_ioport.iop_pcdir &= ~0x000c;
+ immr->im_ioport.iop_pdpar |= 0x0080;
+ immr->im_ioport.iop_pddir &= ~0x0080;
+ immr->im_cpm.cp_pepar |= 0x00000003;
+ immr->im_cpm.cp_pedir |= 0x00000003;
+ immr->im_cpm.cp_peso &= ~0x00000003;
+#elif !defined(CONFIG_ICU862) && !defined(CONFIG_IAD210)
/* Configure all of port D for MII.
*/
immr->im_ioport.iop_pdpar = 0x1fff;
#define PHY_ID_AMD79C784 0x00225610 /* AMD 79C784 */
#define PHY_ID_LSI80225 0x0016f870 /* LSI 80225 */
#define PHY_ID_LSI80225B 0x0016f880 /* LSI 80225/B */
-
+#define PHY_ID_DM9161 0x0181B880 /* Davicom DM9161 */
/* send command to phy using mii, wait for result */
static uint
case PHY_ID_LSI80225B:
printf("LSI L80225/B\n");
break;
+ case PHY_ID_DM9161:
+ printf("Davicom DM9161\n");
+ break;
default:
printf("0x%08x\n", phytype);
break;
*/
fecp->fec_mii_speed = ((bd->bi_intfreq + 4999999) / 5000000) << 1;
-#if !defined(CONFIG_ICU862) && !defined(CONFIG_IAD210)
+#if defined(CONFIG_DUET) /* MPC87x/88x have got 2 FECs and different pinout */
+ immr->im_ioport.iop_papar |= 0xf830;
+ immr->im_ioport.iop_padir |= 0x0830;
+ immr->im_ioport.iop_padir &= ~0xf000;
+ immr->im_cpm.cp_pbpar |= 0x00001001;
+ immr->im_cpm.cp_pbdir &= ~0x00001001;
+ immr->im_ioport.iop_pcpar |= 0x000c;
+ immr->im_ioport.iop_pcdir &= ~0x000c;
+ immr->im_ioport.iop_pdpar |= 0x0080;
+ immr->im_ioport.iop_pddir &= ~0x0080;
+ immr->im_cpm.cp_pepar |= 0x00000003;
+ immr->im_cpm.cp_pedir |= 0x00000003;
+ immr->im_cpm.cp_peso &= ~0x00000003;
+#elif !defined(CONFIG_ICU862) && !defined(CONFIG_IAD210)
/* Configure all of port D for MII.
*/
immr->im_ioport.iop_pdpar = 0x1fff;
/* Reset Timer Expired and Timers Interrupt Status */
immr->im_clkrstk.cark_plprcrk = KAPWR_KEY;
__asm__ ("nop");
-#ifdef CONFIG_MPC866_et_al
- immr->im_clkrst.car_plprcr |= PLPRCR_TEXPS;
-#else
- immr->im_clkrst.car_plprcr |= PLPRCR_TEXPS | PLPRCR_TMIST;
-#endif
+ /*
+ Clear TEXPS (and TMIST on older chips). SPLSS (on older
+ chips) is cleared too.
+
+ Bitwise OR is a read-modify-write operation so ALL bits
+ which are cleared by writing `1' would be cleared by
+ operations like
+
+ immr->im_clkrst.car_plprcr |= PLPRCR_TEXPS;
+
+ The same can be achieved by simple writing of the PLPRCR
+ to itself. If a bit value should be preserved, read the
+ register, ZERO the bit and write, not OR, the result back.
+ */
+ immr->im_clkrst.car_plprcr = immr->im_clkrst.car_plprcr;
}
/************************************************************************/
START = start.o
AOBJS = traps.o
-OBJS = cpu.o interrupts.o serial.o
+OBJS = cpu.o interrupts.o serial.o asmi.o
all: .depend $(START) $(LIB)
--- /dev/null
+/*
+ * (C) Copyright 2003, Psyent Corporation <www.psyent.com>
+ * Scott McNutt <smcnutt@psyent.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+
+#if defined(CONFIG_NIOS_ASMI)
+#include <command.h>
+#include <nios-io.h>
+
+#if !defined(CFG_NIOS_ASMIBASE)
+#error "*** CFG_NIOS_ASMIBASE not defined ***"
+#endif
+
+/*-----------------------------------------------------------------------*/
+#define SHORT_HELP\
+ "asmi - read/write Cyclone ASMI configuration device.\n"
+
+#define LONG_HELP\
+ "\n"\
+ "asmi erase start [end]\n"\
+ " - erase sector start or sectors start through end.\n"\
+ "asmi info\n"\
+ " - display ASMI device information.\n"\
+ "asmi protect on | off\n"\
+ " - turn device protection on or off.\n"\
+ "asmi read addr offset count\n"\
+ " - read count bytes from offset to addr.\n"\
+ "asmi write addr offset count\n"\
+ " - write count bytes to offset from addr.\n"\
+ "asmi verify addr offset count\n"\
+ " - verify count bytes at offset from addr.\n"
+
+
+/*-----------------------------------------------------------------------*/
+/* Operation codes for serial configuration devices
+ */
+#define ASMI_WRITE_ENA 0x06 /* Write enable */
+#define ASMI_WRITE_DIS 0x04 /* Write disable */
+#define ASMI_READ_STAT 0x05 /* Read status */
+#define ASMI_READ_BYTES 0x03 /* Read bytes */
+#define ASMI_READ_ID 0xab /* Read silicon id */
+#define ASMI_WRITE_STAT 0x01 /* Write status */
+#define ASMI_WRITE_BYTES 0x02 /* Write bytes */
+#define ASMI_ERASE_BULK 0xc7 /* Erase entire device */
+#define ASMI_ERASE_SECT 0xd8 /* Erase sector */
+
+/* Device status register bits
+ */
+#define ASMI_STATUS_WIP (1<<0) /* Write in progress */
+#define ASMI_STATUS_WEL (1<<1) /* Write enable latch */
+
+static nios_asmi_t *asmi = (nios_asmi_t *)CFG_NIOS_ASMIBASE;
+
+/***********************************************************************
+ * Device access
+ ***********************************************************************/
+static void asmi_cs (int assert)
+{
+ if (assert) {
+ asmi->control |= NIOS_ASMI_SSO;
+ } else {
+ /* Let all bits shift out */
+ while ((asmi->status & NIOS_ASMI_TMT) == 0)
+ ;
+ asmi->control &= ~NIOS_ASMI_SSO;
+ }
+}
+
+static void asmi_tx (unsigned char c)
+{
+ while ((asmi->status & NIOS_ASMI_TRDY) == 0)
+ ;
+ asmi->txdata = c;
+}
+
+static int asmi_rx (void)
+{
+ while ((asmi->status & NIOS_ASMI_RRDY) == 0)
+ ;
+ return (asmi->rxdata);
+}
+
+static unsigned char bitrev[] = {
+ 0x00, 0x08, 0x04, 0x0c, 0x02, 0x0a, 0x06, 0x0e,
+ 0x01, 0x09, 0x05, 0x0d, 0x03, 0x0b, 0x07, 0x0f
+};
+
+static unsigned char asmi_bitrev( unsigned char c )
+{
+ unsigned char val;
+
+ val = bitrev[c>>4];
+ val |= bitrev[c & 0x0f]<<4;
+ return (val);
+}
+
+static void asmi_rcv (unsigned char *dst, int len)
+{
+ while (len--) {
+ asmi_tx (0);
+ *dst++ = asmi_rx ();
+ }
+}
+
+static void asmi_rrcv (unsigned char *dst, int len)
+{
+ while (len--) {
+ asmi_tx (0);
+ *dst++ = asmi_bitrev (asmi_rx ());
+ }
+}
+
+static void asmi_snd (unsigned char *src, int len)
+{
+ while (len--) {
+ asmi_tx (*src++);
+ asmi_rx ();
+ }
+}
+
+static void asmi_rsnd (unsigned char *src, int len)
+{
+ while (len--) {
+ asmi_tx (asmi_bitrev (*src++));
+ asmi_rx ();
+ }
+}
+
+static void asmi_wr_enable (void)
+{
+ asmi_cs (1);
+ asmi_tx (ASMI_WRITE_ENA);
+ asmi_rx ();
+ asmi_cs (0);
+}
+
+static unsigned char asmi_status_rd (void)
+{
+ unsigned char status;
+
+ asmi_cs (1);
+ asmi_tx (ASMI_READ_STAT);
+ asmi_rx ();
+ asmi_tx (0);
+ status = asmi_rx ();
+ asmi_cs (0);
+ return (status);
+}
+
+static void asmi_status_wr (unsigned char status)
+{
+ asmi_wr_enable ();
+ asmi_cs (1);
+ asmi_tx (ASMI_WRITE_STAT);
+ asmi_rx ();
+ asmi_tx (status);
+ asmi_rx ();
+ asmi_cs (0);
+ return;
+}
+
+/***********************************************************************
+ * Device information
+ ***********************************************************************/
+typedef struct asmi_devinfo_t {
+ const char *name; /* Device name */
+ unsigned char id; /* Device silicon id */
+ unsigned char size; /* Total size log2(bytes)*/
+ unsigned char num_sects; /* Number of sectors */
+ unsigned char sz_sect; /* Sector size log2(bytes) */
+ unsigned char sz_page; /* Page size log2(bytes) */
+ unsigned char prot_mask; /* Protection mask */
+}asmi_devinfo_t;
+
+static struct asmi_devinfo_t devinfo[] = {
+ { "EPCS1 ", 0x10, 17, 4, 15, 8, 0x0c },
+ { "EPCS4 ", 0x12, 19, 8, 16, 8, 0x1c },
+ { 0, 0, 0, 0, 0, 0 }
+};
+
+static asmi_devinfo_t *asmi_dev_find (void)
+{
+ unsigned char buf[4];
+ unsigned char id;
+ int i;
+ struct asmi_devinfo_t *dev = NULL;
+
+ /* Read silicon id requires 3 "dummy bytes" before it's put
+ * on the wire.
+ */
+ buf[0] = ASMI_READ_ID;
+ buf[1] = 0;
+ buf[2] = 0;
+ buf[3] = 0;
+
+ asmi_cs (1);
+ asmi_snd (buf,4);
+ asmi_rcv (buf,1);
+ asmi_cs (0);
+ id = buf[0];
+
+ /* Find the info struct */
+ i = 0;
+ while (devinfo[i].name) {
+ if (id == devinfo[i].id) {
+ dev = &devinfo[i];
+ break;
+ }
+ i++;
+ }
+
+ return (dev);
+}
+
+/***********************************************************************
+ * Misc Utilities
+ ***********************************************************************/
+static unsigned asmi_cfgsz (void)
+{
+ unsigned sz = 0;
+ unsigned char buf[128];
+ unsigned char *p;
+
+ /* Read in the first 128 bytes of the device */
+ buf[0] = ASMI_READ_BYTES;
+ buf[1] = 0;
+ buf[2] = 0;
+ buf[3] = 0;
+
+ asmi_cs (1);
+ asmi_snd (buf,4);
+ asmi_rrcv (buf, sizeof(buf));
+ asmi_cs (0);
+
+ /* Search for the starting 0x6a which is followed by the
+ * 4-byte 'register' and 4-byte bit-count.
+ */
+ p = buf;
+ while (p < buf + sizeof(buf)-8) {
+ if ( *p == 0x6a ) {
+ /* Point to bit count and extract */
+ p += 5;
+ sz = *p++;
+ sz |= *p++ << 8;
+ sz |= *p++ << 16;
+ sz |= *p++ << 24;
+ /* Convert to byte count */
+ sz += 7;
+ sz >>= 3;
+ } else if (*p == 0xff) {
+ /* 0xff is ok ... just skip */
+ p++;
+ continue;
+ } else {
+ /* Not 0xff or 0x6a ... something's not
+ * right ... report 'unknown' (sz=0).
+ */
+ break;
+ }
+ }
+ return (sz);
+}
+
+static int asmi_erase (unsigned start, unsigned end)
+{
+ unsigned off, sectsz;
+ unsigned char buf[4];
+ struct asmi_devinfo_t *dev = asmi_dev_find ();
+
+ if (!dev || (start>end))
+ return (-1);
+
+ /* Erase the requested sectors. An address is required
+ * that lies within the requested sector -- we'll just
+ * use the first address in the sector.
+ */
+ printf ("asmi erasing sector %d ", start);
+ if (start != end)
+ printf ("to %d ", end);
+ sectsz = (1 << dev->sz_sect);
+ while (start <= end) {
+ off = start * sectsz;
+ start++;
+
+ buf[0] = ASMI_ERASE_SECT;
+ buf[1] = off >> 16;
+ buf[2] = off >> 8;
+ buf[3] = off;
+
+ asmi_wr_enable ();
+ asmi_cs (1);
+ asmi_snd (buf,4);
+ asmi_cs (0);
+
+ printf ("."); /* Some user feedback */
+
+ /* Wait for erase to complete */
+ while (asmi_status_rd() & ASMI_STATUS_WIP)
+ ;
+ }
+ printf (" done.\n");
+ return (0);
+}
+
+static int asmi_read (ulong addr, ulong off, ulong cnt)
+{
+ unsigned char buf[4];
+
+ buf[0] = ASMI_READ_BYTES;
+ buf[1] = off >> 16;
+ buf[2] = off >> 8;
+ buf[3] = off;
+
+ asmi_cs (1);
+ asmi_snd (buf,4);
+ asmi_rrcv ((unsigned char *)addr, cnt);
+ asmi_cs (0);
+
+ return (0);
+}
+
+static
+int asmi_write (ulong addr, ulong off, ulong cnt)
+{
+ ulong wrcnt;
+ unsigned pgsz;
+ unsigned char buf[4];
+ struct asmi_devinfo_t *dev = asmi_dev_find ();
+
+ if (!dev)
+ return (-1);
+
+ pgsz = (1<<dev->sz_page);
+ while (cnt) {
+ if (off % pgsz)
+ wrcnt = pgsz - (off % pgsz);
+ else
+ wrcnt = pgsz;
+ wrcnt = (wrcnt > cnt) ? cnt : wrcnt;
+
+ buf[0] = ASMI_WRITE_BYTES;
+ buf[1] = off >> 16;
+ buf[2] = off >> 8;
+ buf[3] = off;
+
+ asmi_wr_enable ();
+ asmi_cs (1);
+ asmi_snd (buf,4);
+ asmi_rsnd ((unsigned char *)addr, wrcnt);
+ asmi_cs (0);
+
+ /* Wait for write to complete */
+ while (asmi_status_rd() & ASMI_STATUS_WIP)
+ ;
+
+ cnt -= wrcnt;
+ off += wrcnt;
+ addr += wrcnt;
+ }
+
+ return (0);
+}
+
+static
+int asmi_verify (ulong addr, ulong off, ulong cnt, ulong *err)
+{
+ ulong rdcnt;
+ unsigned char buf[256];
+ unsigned char *start,*end;
+ int i;
+
+ start = end = (unsigned char *)addr;
+ while (cnt) {
+ rdcnt = (cnt>sizeof(buf)) ? sizeof(buf) : cnt;
+ asmi_read ((ulong)buf, off, rdcnt);
+ for (i=0; i<rdcnt; i++) {
+ if (*end != buf[i]) {
+ *err = end - start;
+ return(-1);
+ }
+ end++;
+ }
+ cnt -= rdcnt;
+ off += rdcnt;
+ }
+ return (0);
+}
+
+static int asmi_sect_erased (int sect, unsigned *offset,
+ struct asmi_devinfo_t *dev)
+{
+ unsigned char buf[128];
+ unsigned off, end;
+ unsigned sectsz;
+ int i;
+
+ sectsz = (1 << dev->sz_sect);
+ off = sectsz * sect;
+ end = off + sectsz;
+
+ while (off < end) {
+ asmi_read ((ulong)buf, off, sizeof(buf));
+ for (i=0; i < sizeof(buf); i++) {
+ if (buf[i] != 0xff) {
+ *offset = off + i;
+ return (0);
+ }
+ }
+ off += sizeof(buf);
+ }
+ return (1);
+}
+
+
+/***********************************************************************
+ * Commands
+ ***********************************************************************/
+static
+void do_asmi_info (struct asmi_devinfo_t *dev, int argc, char *argv[])
+{
+ int i;
+ unsigned char stat;
+ unsigned tmp;
+ int erased;
+
+ /* Basic device info */
+ printf ("%s: %d kbytes (%d sectors x %d kbytes,"
+ " %d bytes/page)\n",
+ dev->name, 1 << (dev->size-10),
+ dev->num_sects, 1 << (dev->sz_sect-10),
+ 1 << dev->sz_page );
+
+ /* Status -- for now protection is all-or-nothing */
+ stat = asmi_status_rd();
+ printf ("status: 0x%02x (WIP:%d, WEL:%d, PROT:%s)\n",
+ stat,
+ (stat & ASMI_STATUS_WIP) ? 1 : 0,
+ (stat & ASMI_STATUS_WEL) ? 1 : 0,
+ (stat & dev->prot_mask) ? "on" : "off" );
+
+ /* Configuration */
+ tmp = asmi_cfgsz ();
+ if (tmp) {
+ printf ("config: 0x%06x (%d) bytes\n", tmp, tmp );
+ } else {
+ printf ("config: unknown\n" );
+ }
+
+ /* Sector info */
+ for (i=0; i<dev->num_sects; i++) {
+ erased = asmi_sect_erased (i, &tmp, dev);
+ printf (" %d: %06x ",
+ i, i*(1<<dev->sz_sect) );
+ if (erased)
+ printf ("erased\n");
+ else
+ printf ("data @ 0x%06x\n", tmp);
+ }
+
+ return;
+}
+
+static
+void do_asmi_erase (struct asmi_devinfo_t *dev, int argc, char *argv[])
+{
+ unsigned start,end;
+
+ if ((argc < 3) || (argc > 4)) {
+ printf ("USAGE: asmi erase sect [end]\n");
+ return;
+ }
+ if ((asmi_status_rd() & dev->prot_mask) != 0) {
+ printf ( "asmi: device protected.\n");
+ return;
+ }
+
+ start = simple_strtoul (argv[2], NULL, 10);
+ if (argc > 3)
+ end = simple_strtoul (argv[3], NULL, 10);
+ else
+ end = start;
+ if ((start >= dev->num_sects) || (start > end)) {
+ printf ("asmi: invalid sector range: [%d:%d]\n",
+ start, end );
+ return;
+ }
+
+ asmi_erase (start, end);
+
+ return;
+}
+
+static
+void do_asmi_protect (struct asmi_devinfo_t *dev, int argc, char *argv[])
+{
+ unsigned char stat;
+
+ /* For now protection is all-or-nothing to keep things
+ * simple. The protection bits don't map in a linear
+ * fashion ... and we would rather protect the bottom
+ * of the device since it contains the config data and
+ * leave the top unprotected for app use. But unfortunately
+ * protection works from top-to-bottom so it does
+ * really help very much from a software app point-of-view.
+ */
+ if (argc < 3) {
+ printf ("USAGE: asmi protect on | off\n");
+ return;
+ }
+ if (!dev)
+ return;
+
+ /* Protection on/off is just a matter of setting/clearing
+ * all protection bits in the status register.
+ */
+ stat = asmi_status_rd ();
+ if (strcmp ("on", argv[2]) == 0) {
+ stat |= dev->prot_mask;
+ } else if (strcmp ("off", argv[2]) == 0 ) {
+ stat &= ~dev->prot_mask;
+ } else {
+ printf ("asmi: unknown protection: %s\n", argv[2]);
+ return;
+ }
+ asmi_status_wr (stat);
+ return;
+}
+
+static
+void do_asmi_read (struct asmi_devinfo_t *dev, int argc, char *argv[])
+{
+ ulong addr,off,cnt;
+ ulong sz;
+
+ if (argc < 5) {
+ printf ("USAGE: asmi read addr offset count\n");
+ return;
+ }
+
+ sz = 1 << dev->size;
+ addr = simple_strtoul (argv[2], NULL, 16);
+ off = simple_strtoul (argv[3], NULL, 16);
+ cnt = simple_strtoul (argv[4], NULL, 16);
+ if (off > sz) {
+ printf ("offset is greater than device size"
+ "... aborting.\n");
+ return;
+ }
+ if ((off + cnt) > sz) {
+ printf ("request exceeds device size"
+ "... truncating.\n");
+ cnt = sz - off;
+ }
+ printf ("asmi: read %08lx <- %06lx (0x%lx bytes)\n",
+ addr, off, cnt);
+ asmi_read (addr, off, cnt);
+
+ return;
+}
+
+static
+void do_asmi_write (struct asmi_devinfo_t *dev, int argc, char *argv[])
+{
+ ulong addr,off,cnt;
+ ulong sz;
+ ulong err;
+
+ if (argc < 5) {
+ printf ("USAGE: asmi write addr offset count\n");
+ return;
+ }
+ if ((asmi_status_rd() & dev->prot_mask) != 0) {
+ printf ( "asmi: device protected.\n");
+ return;
+ }
+
+ sz = 1 << dev->size;
+ addr = simple_strtoul (argv[2], NULL, 16);
+ off = simple_strtoul (argv[3], NULL, 16);
+ cnt = simple_strtoul (argv[4], NULL, 16);
+ if (off > sz) {
+ printf ("offset is greater than device size"
+ "... aborting.\n");
+ return;
+ }
+ if ((off + cnt) > sz) {
+ printf ("request exceeds device size"
+ "... truncating.\n");
+ cnt = sz - off;
+ }
+ printf ("asmi: write %08lx -> %06lx (0x%lx bytes)\n",
+ addr, off, cnt);
+ asmi_write (addr, off, cnt);
+ if (asmi_verify (addr, off, cnt, &err) != 0)
+ printf ("asmi: write error at offset %06lx\n", err);
+
+ return;
+}
+
+static
+void do_asmi_verify (struct asmi_devinfo_t *dev, int argc, char *argv[])
+{
+ ulong addr,off,cnt;
+ ulong sz;
+ ulong err;
+
+ if (argc < 5) {
+ printf ("USAGE: asmi verify addr offset count\n");
+ return;
+ }
+
+ sz = 1 << dev->size;
+ addr = simple_strtoul (argv[2], NULL, 16);
+ off = simple_strtoul (argv[3], NULL, 16);
+ cnt = simple_strtoul (argv[4], NULL, 16);
+ if (off > sz) {
+ printf ("offset is greater than device size"
+ "... aborting.\n");
+ return;
+ }
+ if ((off + cnt) > sz) {
+ printf ("request exceeds device size"
+ "... truncating.\n");
+ cnt = sz - off;
+ }
+ printf ("asmi: verify %08lx -> %06lx (0x%lx bytes)\n",
+ addr, off, cnt);
+ if (asmi_verify (addr, off, cnt, &err) != 0)
+ printf ("asmi: verify error at offset %06lx\n", err);
+
+ return;
+}
+
+/*-----------------------------------------------------------------------*/
+int do_asmi (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+ int len;
+ struct asmi_devinfo_t *dev = asmi_dev_find ();
+
+ if (argc < 2) {
+ printf ("Usage:%s", LONG_HELP);
+ return (0);
+ }
+
+ if (!dev) {
+ printf ("asmi: device not found.\n");
+ return (0);
+ }
+
+ len = strlen (argv[1]);
+ if (strncmp ("info", argv[1], len) == 0) {
+ do_asmi_info ( dev, argc, argv);
+ } else if (strncmp ("erase", argv[1], len) == 0) {
+ do_asmi_erase (dev, argc, argv);
+ } else if (strncmp ("protect", argv[1], len) == 0) {
+ do_asmi_protect (dev, argc, argv);
+ } else if (strncmp ("read", argv[1], len) == 0) {
+ do_asmi_read (dev, argc, argv);
+ } else if (strncmp ("write", argv[1], len) == 0) {
+ do_asmi_write (dev, argc, argv);
+ } else if (strncmp ("verify", argv[1], len) == 0) {
+ do_asmi_verify (dev, argc, argv);
+ } else {
+ printf ("asmi: unknown operation: %s\n", argv[1]);
+ }
+
+ return (0);
+}
+
+/*-----------------------------------------------------------------------*/
+
+
+U_BOOT_CMD( asmi, 5, 0, do_asmi, SHORT_HELP, LONG_HELP );
+
+#endif /* CONFIG_NIOS_ASMI */
printf ("CPU: ");
printf ("%s", (val & 0x00008000) ? "Nios-16 " : "Nios-32 ");
rev_major = (val>>12) & 0x07;
- rev_minor = val & 0x0f;
- printf ("Rev. %d.%02d (0x%04x)", rev_major, rev_minor,
+ rev_minor = (val>>4) & 0x0ff;
+ printf ("Rev. %d.%d (0x%04x)", rev_major, rev_minor,
val & 0xffff);
if (rev_major == 0x08)
printf (" [OpenCore (R) Plus]");
Nios Development Kit
Cyclone Editions
- Last Update: October 15, 2003
+ Last Update: January 2, 2004
====================================================================
This file contains information regarding U-Boot and the Altera
For those interested in contributing ... see HELP WANTED section
in doc/README.nios.
+Contents:
-Files
-------
+ 1. Files
+ 2. Memory Organization
+ 3. Examples
+ 4. Programming U-Boot into FLASH with GERMS
+ 5. Active Serial Memory Interface (ASMI) Support
+
+====================================================================
+
+1. Files
+=========
board/dk1c20/*
include/configs/DK1C20.h
-Memory Organization
---------------------
+2. Memory Organization
+=======================
- -The heap is placed below the monitor (U-Boot code).
- -Global data is placed below the heap.
- -The stack is placed below global data (&grows down).
+ -The heap is placed below the monitor (U-Boot code).
+ -Global data is placed below the heap.
+ -The stack is placed below global data (&grows down).
-Misc
------
+3. Examples
+============
-The hello_world example works fine.
+The hello_world example works fine. The default load address
+is 0x0100_0000 (the start of SDRAM).
-Programming U-Boot into FLASH with GERMS
------------------------------------------
-The current version of the DK-1C20 port occupies less than
-60 KByte with network support disabled. So everything will fit
-into a single flash sector. With network support (e.g. bootp,
-tftpboot, ping, etc) the flash footprint is about 77K.
+4. Programming U-Boot into FLASH with GERMS
+============================================
+The current version of the DK-1C20 port with the default
+configuration settings occupies about 81 KBytes of flash.
+A minimal configuration occupies less than 60 KByte (asmi
+and network support disabled).
To program U-Boot into the DK-1C20 flash using GERMS do the
following:
U-Boot 1.0.0-pre (Oct 4 2003 - 07:39:24)
- CPU: Nios-32 Rev. 3.08 (0x3018)
+ CPU: Nios-32 Rev. 3.3 (0x3038)
Reg file size: 256 LO_LIMIT/HI_LIMIT: 2/14
Board: Altera Nios 1C20 Development Kit
- In: serial
+ In: serial
Out: serial
Err: serial
==>
2. Quit nios-run and start your terminal application (e.g. start
Hyperterminal or minicom).
-3. From the U-Boot command prompt, erase a sector of flash at 0x40000:
+3. From the U-Boot command prompt, erase flash 0x40000 to 0x 5ffff:
- ==> erase 40000 4ffff
+ ==> erase 1:4-5
4. Download the u-boot code to RAM. When using Hyperterminal, do the
following:
- --From the u-boot command prompt start a binary download to SRAM:
+ a. From the u-boot command prompt start a binary download to SRAM:
==> loadb 800000
- --Download u-boot.bin using kermit.
+ b. Download u-boot.bin using kermit.
5. Copy the binary image from SRAM to flash:
Safe-32 configuration, enter the following GERMS command:
+ g 40000
+
+5. Active Serial Memory Interface (ASMI) Support
+================================================
+ASMI is fully supported in U-Boot. Please note that ASMI is supported
+only on Cyclone devices. Do not expect ASMI to work with Stratix or
+APEX devices.
+
+ ************* IMPORTANT *************
+ ===================================================
+ IN ORDER FOR THE NIOS ASMI TO OPERATE PROPERLY, THE
+ CYCLONE DEVICE MUST BE CONFIGURED USING JTAG OR ASMI.
+
+There are two techniques you can use to bootstrap the ASMI. The
+first is to use the program_epcs utility that is part of Altera's SDK.
+But I've found program_epcs to be slow and cumbersome at best.
+
+An undocumented alternative is to use the Quartus device programing
+interface:
+
+ 1. Select "Active Serial" mode.
+
+ 2. Choose the xxx.pof file. For example, for the standard_32
+ configuration use the "standard_32.pof" file.
+
+ 3. Attach your ByteBlaster to J28. Make sure you have the
+ cable attached properly -- the orientation of J28 is
+ different than J24 (the JTAG header). On J28, pin 1 is on
+ the bottom row, left-most pin.
+
+ 4. Press and hold the "Power-On Reset" switch (SW10). You will
+ see the green "Loading" and red "Error" LEDs (LED3 and LED4)
+ in the on state.
+
+ 5. While holding down the "Power-On Reset" switch, start the
+ programming sequence. This only takes about 10 seconds.
+
+ 6. After programming is complete, release the "Power-On Reset"
+ switch. The Cyclone device should now load its configuration
+ from the EPCS4 (U59). The green "User" LED (LED 1) should be
+ blinking if the device was successfully loaded via ASMI.
+
+ 7. Remove the ByteBlaster cable. The cable must be removed to
+ allow the Nios ASMI access to the EPCS4 device.
+
+After you have successfully programmed a configuration into the
+EPCS4, the ASMI will be used to load the Cyclone configuration
+unless the "Force Safe" switch (SW9) is pressed.
+
+NOTE: To maximize the amount of space available for program use,
+you can enable configuration compression in Quartus. With compression
+enabled, the size of the standard_32 configuration data is
+approximately 192 KBytes.
+
+To use the U-Boot ASMI commands, try typing "help asmi" at the
+command prompt. The command "asmi info" will show the current
+status of the ASMI.
U-Boot for Nios-32
- Last Update: November 30, 2003
+ Last Update: January 2, 2004
====================================================================
This file contains information regarding U-Boot and the Altera
U-Boot has been successfully tested on the Nios Cyclone development
board using both the 'safe' and 'standard 32' configurations with
-Nios CPU revision 3.08 (CPU_ID = 0x3008). U-Boot can be used with
+Nios CPU revision 3.1 (CPU_ID = 0x3018). U-Boot can be used with
or without the GERMS monitor. The initial version of U-Boot for the
Cyclone development kit is about 60 Kbyte and will fit in a single
sector of on-board FLASH. Only the Nios 32-bit CPU is supported.
a problem as little, if any, of the Altera source contains
features that are not already available in U-Boot.
-The Nios port also does not use the long-winded peripheral
-structure definitions from the Nios SDK.
-
2. CONFIGURATION OPTIONS/SETTINGS
----------------------------------
CFG_NIOS_TMRMS -- the period of the timer in milliseconds.
+CFG_NIOS_ASMIBASE -- the base address of the ASMI peripheral.
+ (standard-32: na_asmi_base).
+
2.2 Differences in U-Boot Options/Settings
-------------------------------------------
Some 'standard' U-Boot options/settings are treated differently in
-CompactFlash. Port & test CF/FAT.
--ASMI support. Use ASMI for environment, etc.
-
-Bedbug. Develop bedbug for Nios ... or at least provide a disassemble
command.
#include <asm/byteorder.h>
#include <linux/stat.h>
+#include <jffs2/jffs2.h>
#include <jffs2/load_kernel.h>
-#include "cramfs_fs.h"
+#include <cramfs/cramfs_fs.h>
/* These two macros may change in future, to provide better st_ino
semantics. */
(unsigned long) loadoffset);
}
-static char *mkmodestr (unsigned long mode, char *str)
-{
- static const char *l = "xwr";
- int mask = 1, i;
- char c;
-
- switch (mode & S_IFMT) {
- case S_IFDIR: str[0] = 'd'; break;
- case S_IFBLK: str[0] = 'b'; break;
- case S_IFCHR: str[0] = 'c'; break;
- case S_IFIFO: str[0] = 'f'; break;
- case S_IFLNK: str[0] = 'l'; break;
- case S_IFSOCK: str[0] = 's'; break;
- case S_IFREG: str[0] = '-'; break;
- default: str[0] = '?'; break;
- }
-
- for (i = 0; i < 9; i++) {
- c = l[i % 3];
- str[9 - i] = (mode & mask) ? c : '-';
- mask = mask << 1;
- }
-
- if (mode & S_ISUID) str[3] = (mode & S_IXUSR) ? 's' : 'S';
- if (mode & S_ISGID) str[6] = (mode & S_IXGRP) ? 's' : 'S';
- if (mode & S_ISVTX) str[9] = (mode & S_IXOTH) ? 't' : 'T';
- str[10] = '\0';
- return str;
-}
-
static int cramfs_list_inode (struct part_info *info, unsigned long offset)
{
struct cramfs_inode *inode = (struct cramfs_inode *)
+++ /dev/null
-#ifndef __CRAMFS_FS_H
-#define __CRAMFS_FS_H
-
-/* Uncompression interfaces to the underlying zlib */
-int cramfs_uncompress_block (void *dst, void *src, int srclen);
-int cramfs_uncompress_init (void);
-
-#define CRAMFS_MAGIC 0x28cd3d45 /* some random number */
-#define CRAMFS_SIGNATURE "Compressed ROMFS"
-
-/*
- * Width of various bitfields in struct cramfs_inode.
- * Primarily used to generate warnings in mkcramfs.
- */
-#define CRAMFS_MODE_WIDTH 16
-#define CRAMFS_UID_WIDTH 16
-#define CRAMFS_SIZE_WIDTH 24
-#define CRAMFS_GID_WIDTH 8
-#define CRAMFS_NAMELEN_WIDTH 6
-#define CRAMFS_OFFSET_WIDTH 26
-
-/*
- * Since inode.namelen is a unsigned 6-bit number, the maximum cramfs
- * path length is 63 << 2 = 252.
- */
-#define CRAMFS_MAXPATHLEN (((1 << CRAMFS_NAMELEN_WIDTH) - 1) << 2)
-
-/*
- * Reasonably terse representation of the inode data.
- */
-struct cramfs_inode {
- u32 mode:CRAMFS_MODE_WIDTH, uid:CRAMFS_UID_WIDTH;
- /* SIZE for device files is i_rdev */
- u32 size:CRAMFS_SIZE_WIDTH, gid:CRAMFS_GID_WIDTH;
- /* NAMELEN is the length of the file name, divided by 4 and
- rounded up. (cramfs doesn't support hard links.) */
- /* OFFSET: For symlinks and non-empty regular files, this
- contains the offset (divided by 4) of the file data in
- compressed form (starting with an array of block pointers;
- see README). For non-empty directories it is the offset
- (divided by 4) of the inode of the first file in that
- directory. For anything else, offset is zero. */
- u32 namelen:CRAMFS_NAMELEN_WIDTH, offset:CRAMFS_OFFSET_WIDTH;
-};
-
-struct cramfs_info {
- u32 crc;
- u32 edition;
- u32 blocks;
- u32 files;
-};
-
-/*
- * Superblock information at the beginning of the FS.
- */
-struct cramfs_super {
- u32 magic; /* 0x28cd3d45 - random number */
- u32 size; /* length in bytes */
- u32 flags; /* feature flags */
- u32 future; /* reserved for future use */
- u8 signature[16]; /* "Compressed ROMFS" */
- struct cramfs_info fsid; /* unique filesystem info */
- u8 name[16]; /* user-defined name */
- struct cramfs_inode root; /* root inode data */
-};
-
-/*
- * Feature flags
- *
- * 0x00000000 - 0x000000ff: features that work for all past kernels
- * 0x00000100 - 0xffffffff: features that don't work for past kernels
- */
-#define CRAMFS_FLAG_FSID_VERSION_2 0x00000001 /* fsid version #2 */
-#define CRAMFS_FLAG_SORTED_DIRS 0x00000002 /* sorted dirs */
-#define CRAMFS_FLAG_HOLES 0x00000100 /* support for holes */
-#define CRAMFS_FLAG_WRONG_SIGNATURE 0x00000200 /* reserved */
-#define CRAMFS_FLAG_SHIFTED_ROOT_OFFSET 0x00000400 /* shifted root fs */
-
-/*
- * Valid values in super.flags. Currently we refuse to mount
- * if (flags & ~CRAMFS_SUPPORTED_FLAGS). Maybe that should be
- * changed to test super.future instead.
- */
-#define CRAMFS_SUPPORTED_FLAGS ( 0x000000ff \
- | CRAMFS_FLAG_HOLES \
- | CRAMFS_FLAG_WRONG_SIGNATURE \
- | CRAMFS_FLAG_SHIFTED_ROOT_OFFSET )
-
-/*
- * Since cramfs is little-endian, provide macros to swab the bitfields.
- */
-
-#ifndef __BYTE_ORDER
-#if defined(__LITTLE_ENDIAN) && !defined(__BIG_ENDIAN)
-#define __BYTE_ORDER __LITTLE_ENDIAN
-#elif defined(__BIG_ENDIAN) && !defined(__LITTLE_ENDIAN)
-#define __BYTE_ORDER __BIG_ENDIAN
-#else
-#error "unable to define __BYTE_ORDER"
-#endif
-#endif /* not __BYTE_ORDER */
-
-#if __BYTE_ORDER == __LITTLE_ENDIAN
-#define CRAMFS_16(x) (x)
-#define CRAMFS_24(x) (x)
-#define CRAMFS_32(x) (x)
-#define CRAMFS_GET_NAMELEN(x) ((x)->namelen)
-#define CRAMFS_GET_OFFSET(x) ((x)->offset)
-#define CRAMFS_SET_OFFSET(x,y) ((x)->offset = (y))
-#define CRAMFS_SET_NAMELEN(x,y) ((x)->namelen = (y))
-#elif __BYTE_ORDER == __BIG_ENDIAN
-#ifdef __KERNEL__
-#define CRAMFS_16(x) swab16(x)
-#define CRAMFS_24(x) ((swab32(x)) >> 8)
-#define CRAMFS_32(x) swab32(x)
-#else /* not __KERNEL__ */
-#define CRAMFS_16(x) bswap_16(x)
-#define CRAMFS_24(x) ((bswap_32(x)) >> 8)
-#define CRAMFS_32(x) bswap_32(x)
-#endif /* not __KERNEL__ */
-#define CRAMFS_GET_NAMELEN(x) (((u8*)(x))[8] & 0x3f)
-#define CRAMFS_GET_OFFSET(x) ((CRAMFS_24(((u32*)(x))[2] & 0xffffff) << 2) |\
- ((((u32*)(x))[2] & 0xc0000000) >> 30))
-#define CRAMFS_SET_NAMELEN(x,y) (((u8*)(x))[8] = (((0x3f & (y))) | \
- (0xc0 & ((u8*)(x))[8])))
-#define CRAMFS_SET_OFFSET(x,y) (((u32*)(x))[2] = (((y) & 3) << 30) | \
- CRAMFS_24((((y) & 0x03ffffff) >> 2)) | \
- (((u32)(((u8*)(x))[8] & 0x3f)) << 24))
-#else
-#error "__BYTE_ORDER must be __LITTLE_ENDIAN or __BIG_ENDIAN"
-#endif
-
-#endif /* not __CRAMFS_FS_H */
return inode;
}
-static char *mkmodestr(unsigned long mode, char *str)
+char *mkmodestr(unsigned long mode, char *str)
{
static const char *l = "xwr";
int mask = 1, i;
u_char res13[2];
ushort cp_pbodr;
uint cp_pbdat;
- u_char res14[0x18];
+
+ /* Port E - MPC87x/88x only.
+ */
+ uint cp_pedir;
+ uint cp_pepar;
+ uint cp_peso;
+ uint cp_peodr;
+ uint cp_pedat;
+
+ /* Communications Processor Timing Register -
+ Contains RMII Timing for the FECs on MPC87x/88x only.
+ */
+ uint cp_cptr;
/* Serial Interface and Time Slot Assignment.
*/
0x0343, 0x0454, 0x0565, 0x0565, 0x0676, 0x0787, 0x0898, 0x0999,
0x0AAA, 0x0ABA, 0x0BCB, 0x0CCC, 0x0DDD, 0x0EEE, 0x0FFF, 0x0FB3,
0x0FB4, 0x0FC4, 0x0FC5, 0x0FC6, 0x0FD7, 0x0FD8, 0x0FD9, 0x0FDA,
- 0x0FEA, 0x0FEB, 0x0FEC, 0x0FFD, 0x0FFE, 0x0FFF, 0x0FFF,
+ 0x0FEA, 0x0FEB, 0x0FEC, 0x0FFD, 0x0FFE, 0x0FFF, 0x0FFF,
};
unsigned char bmp_logo_bitmap[] = {
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
typedef unsigned char uchar;
typedef volatile unsigned long vu_long;
-typedef volatile unsigned short vu_short;
+typedef volatile unsigned short vu_short;
typedef volatile unsigned char vu_char;
#include <config.h>
#if defined(CONFIG_PCI) && defined(CONFIG_440)
#include <pci.h>
#endif
-#ifdef CONFIG_8xx
+#if defined(CONFIG_8xx)
#include <asm/8xx_immap.h>
-#ifdef CONFIG_MPC860
-#define CONFIG_MPC86x 1
-#endif
-#ifdef CONFIG_MPC860T
-#define CONFIG_MPC86x 1
-#endif
#if defined(CONFIG_MPC852) || defined(CONFIG_MPC852T) || \
defined(CONFIG_MPC859) || defined(CONFIG_MPC859T) || \
defined(CONFIG_MPC859DSL) || \
defined(CONFIG_MPC866) || defined(CONFIG_MPC866T) || \
defined(CONFIG_MPC866P)
-#define CONFIG_MPC866_et_al 1
-#define CONFIG_MPC86x 1
+# define CONFIG_MPC866_et_al 1
+#elif defined(CONFIG_MPC870) \
+ || defined(CONFIG_MPC875) \
+ || defined(CONFIG_MPC880) \
+ || defined(CONFIG_MPC885)
+# define CONFIG_DUET 1
+#endif
+#if defined(CONFIG_MPC860) \
+ || defined(CONFIG_MPC860T) \
+ || defined(CONFIG_MPC866_et_al) \
+ || defined(CONFIG_DUET)
+# define CONFIG_MPC86x 1
#endif
#elif defined(CONFIG_5xx)
#include <asm/5xx_immap.h>
/*** FADS860T********************************************************/
-#if (defined(CONFIG_MPC860T) || defined(CONFIG_MPC866_et_al)) \
- && defined(CONFIG_FADS)
-/* This ENET stuff is for the MPC860TFADS/MPC8xxADS with ethernet on SCC1.
+#if defined(CONFIG_FADS) && defined(CONFIG_MPC86x)
+/*
+ * This ENET stuff is for the MPC86xFADS/MPC8xxADS with ethernet on SCC1.
*/
#ifdef CONFIG_SCC1_ENET
+
#define SCC_ENET 0
-#endif /* CONFIG_SCC1_ETHERNET */
+
#define PROFF_ENET PROFF_SCC1
#define CPM_CR_ENET CPM_CR_CH_SCC1
#define SICR_ENET_MASK ((uint)0x000000ff)
#define SICR_ENET_CLKRT ((uint)0x0000002c)
-/* This ENET stuff is for the MPC860TFADS with ethernet on FEC.
+#endif /* CONFIG_SCC1_ETHERNET */
+
+/*
+ * This ENET stuff is for the MPC860TFADS/MPC86xADS/DUET with ethernet on FEC.
*/
#ifdef CONFIG_FEC_ENET
-#define FEC_ENET /* use FEC for EThernet */
-#endif /* CONFIG_FEC_ETHERNET */
+#define FEC_ENET /* Use FEC for Ethernet */
+#endif /* CONFIG_FEC_ENET */
-#endif /* CONFIG_FADS860T */
+#endif /* CONFIG_FADS && CONFIG_MPC86x */
/*** FPS850L, FPS860L ************************************************/
* Helmut Buchsbaum added bitvalues for BCSRx
*
* Copyright (c) 1998 Dan Malek (dmalek@jlc.net)
+ *
+ * Modified by, Yuli Barcohen, Arabella Software Ltd., yuli@arabellasw.com
+ *
+ * Values common to all FADS family boards are in board/fads/fads.h
*/
-/* ------------------------------------------------------------------------- */
-
-#ifndef _CONFIG_ADS860_H
-#define _CONFIG_ADS860_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
+#ifndef __CONFIG_H
+#define __CONFIG_H
/* Board type */
#define CONFIG_ADS 1 /* Old Motorola MPC821/860ADS */
#define CFG_8XX_FACT 12 /* Multiply by 12 */
#endif
-#define CONFIG_8xx_GCLK_FREQ ((CFG_8XX_XIN) * (CFG_8XX_FACT))
-
-#define CONFIG_DRAM_50MHZ 1
-
-#if 0
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
-
-#undef CONFIG_BOOTARGS
-#define CONFIG_BOOTCOMMAND \
- "dhcp;" \
- "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \
- "bootm"
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE)
-
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
- | CFG_CMD_DHCP \
- | CFG_CMD_IMMAP \
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
+ | CFG_CMD_DHCP \
+ | CFG_CMD_IMMAP \
| CFG_CMD_PCMCIA \
- | CFG_CMD_PING \
+ | CFG_CMD_PING \
)
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
-
-/*
- * Miscellaneous configurable options
- */
-#undef CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=>" /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x00100000 /* memtest works on */
-#define CFG_MEMTEST_END 0x00F00000 /* 1 ... 15 MB in DRAM */
+#define CONFIG_DRAM_50MHZ 1
-#define CFG_LOAD_ADDR 0x00100000
+#include "fads.h"
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CFG_IMMR 0xFF000000
-#define CFG_IMMR_SIZE ((uint)(64 * 1024))
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CFG_INIT_RAM_ADDR CFG_IMMR
-#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
-#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
- */
-#define CFG_SDRAM_BASE 0x00000000
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CFG_FLASH_BASE TEXT_BASE
-#define CFG_FLASH_SIZE ((uint)(8 * 1024 * 1024)) /* max 8Mbyte */
-
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 16 /* max number of sectors on one chip */
-
-#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
-#undef CFG_ENV_IS_IN_NVRAM
-#undef CFG_ENV_IS_IN_EEPROM
-#define CFG_ENV_IS_IN_FLASH 1
-
-#define CFG_ENV_SECT_SIZE 0x40000 /* see README - env sector total size */
-#define CFG_ENV_OFFSET CFG_ENV_SECT_SIZE
-#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment */
-
-#define CFG_MONITOR_BASE CFG_FLASH_BASE
-#define CFG_MONITOR_LEN (256 << 10) /* Reserve one flash sector
- (256 KB) for monitor */
-#define CFG_MALLOC_LEN (384 << 10) /* Reserve 384 kB for malloc() */
-
-/* the other CS:s are determined by looking at parameters in BCSRx */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * I2C configuration
- */
-#if (CONFIG_COMMANDS & CFG_CMD_I2C)
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address defaults */
-#define CFG_I2C_SLAVE 0x7F
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control 11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
- SYPCR_SWE | SYPCR_SWRI | SYPCR_SWP)
-#else
-#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SUMCR - SIU Module Configuration 11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control 11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CFG_PISCR (PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
- *-----------------------------------------------------------------------
- * set the PLL, the low-power modes and the reset control (15-29)
- */
#define CFG_PLPRCR (((CFG_8XX_FACT-1) << PLPRCR_MF_SHIFT) | \
PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register 15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK SCCR_EBDF11
-#define CFG_SCCR (SCCR_TBS | SCCR_COM00 | SCCR_DFSYNC00 | \
- SCCR_DFBRG00 | SCCR_DFNL000 | SCCR_DFNH000 | \
- SCCR_DFLCD000 | SCCR_DFALCD00)
-
-
- /*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CFG_DER 0
-
-/* Because of the way the 860 starts up and assigns CS0 the
-* entire address space, we have to set the memory controller
-* differently. Normally, you write the option register
-* first, and then enable the chip select by writing the
-* base register. For CS0, you must write the base register
-* first, followed by the option register.
-*/
-
-/*
- * Init Memory Controller:
- *
- * BR0 and OR0 (FLASH)
- * BR1 and OR1 (BCSR)
- */
-/* the other CS:s are determined by looking at parameters in BCSRx */
-
-#define BCSR_ADDR ((uint) 0xff010000)
-
-#define CFG_PRELIM_OR_AM 0xff800000 /* OR addr mask */
-
-/* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0 */
-#define CFG_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK | OR_TRLX)
-
-#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH) /* 8 Mbyte until detected */
-#define CFG_BR0_PRELIM (CFG_FLASH_BASE | BR_V)
-
-/* BCSRx - Board Control and Status Registers */
-#define CFG_OR1_PRELIM 0xffff8110 /* 64Kbyte address space */
-#define CFG_BR1_PRELIM ((BCSR_ADDR) | BR_V )
-
-/*
- * Memory Periodic Timer Prescaler
- */
-
-/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */
-#define CFG_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
-#define CFG_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
-#define CFG_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
-#define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-
-/* values according to the manual */
-#define BCSR0 (BCSR_ADDR + 0x00)
-#define BCSR1 (BCSR_ADDR + 0x04)
-#define BCSR2 (BCSR_ADDR + 0x08)
-#define BCSR3 (BCSR_ADDR + 0x0c)
-
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-#ifdef CONFIG_MPC860
-#define PCMCIA_SLOT_A 1
-#endif
-
-#define CFG_PCMCIA_MEM_ADDR (0xE0000000)
-#define CFG_PCMCIA_MEM_SIZE ( 64 << 20 )
-#define CFG_PCMCIA_DMA_ADDR (0xE4000000)
-#define CFG_PCMCIA_DMA_SIZE ( 64 << 20 )
-#define CFG_PCMCIA_ATTRB_ADDR (0xE8000000)
-#define CFG_PCMCIA_ATTRB_SIZE ( 64 << 20 )
-#define CFG_PCMCIA_IO_ADDR (0xEC000000)
-#define CFG_PCMCIA_IO_SIZE ( 64 << 20 )
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff
- *-----------------------------------------------------------------------
- */
-#define CONFIG_IDE_8xx_DIRECT 1 /* PCMCIA interface required */
-#undef CONFIG_IDE_LED /* LED for ide supported */
-#define CONFIG_IDE_RESET 1 /* reset for ide supported */
-
-#define CFG_IDE_MAXBUS 1 /* max. 2 IDE busses */
-#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*2) /* max. 2 drives per IDE bus */
-
-#define CFG_PIO_MODE 0 /* IDE interface in PIO Mode 0 */
#define CFG_PC_IDE_RESET ((ushort)0x0008) /* PC 12 */
-#define CFG_ATA_BASE_ADDR CFG_PCMCIA_MEM_ADDR
-#define CFG_ATA_IDE0_OFFSET 0x0000
-
-#define CFG_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */
-#define CFG_ATA_REG_OFFSET 0x0080 /* Offset for normal register accesses */
-#define CFG_ATA_ALT_OFFSET 0x0100 /* Offset for alternate registers */
-
-#define CONFIG_DISK_SPINUP_TIME 1000000
-#undef CONFIG_DISK_SPINUP_TIME /* usin´ Compact Flash */
-
-/* (F)ADS bitvalues by Helmut Buchsbaum
- * see MPC8xxADS User's Manual for a proper description
- * of the following structures
- */
-
-#define BCSR0_ERB ((uint)0x80000000)
-#define BCSR0_IP ((uint)0x40000000)
-#define BCSR0_BDIS ((uint)0x10000000)
-#define BCSR0_BPS_MASK ((uint)0x0C000000)
-#define BCSR0_ISB_MASK ((uint)0x01800000)
-#define BCSR0_DBGC_MASK ((uint)0x00600000)
-#define BCSR0_DBPC_MASK ((uint)0x00180000)
-#define BCSR0_EBDF_MASK ((uint)0x00060000)
-
-#define BCSR1_FLASH_EN ((uint)0x80000000)
-#define BCSR1_DRAM_EN ((uint)0x40000000)
-#define BCSR1_ETHEN ((uint)0x20000000)
-#define BCSR1_IRDEN ((uint)0x10000000)
-#define BCSR1_FLASH_CFG_EN ((uint)0x08000000)
-#define BCSR1_CNT_REG_EN_PROTECT ((uint)0x04000000)
-#define BCSR1_BCSR_EN ((uint)0x02000000)
-#define BCSR1_RS232EN_1 ((uint)0x01000000)
-#define BCSR1_PCCEN ((uint)0x00800000)
-#define BCSR1_PCCVCC0 ((uint)0x00400000)
-#define BCSR1_PCCVCCON BCSR1_PCCVCC0
-#define BCSR1_PCCVPP_MASK ((uint)0x00300000)
-#define BCSR1_DRAM_HALF_WORD ((uint)0x00080000)
-#define BCSR1_RS232EN_2 ((uint)0x00040000)
-#define BCSR1_SDRAM_EN ((uint)0x00020000)
-#define BCSR1_PCCVCC1 ((uint)0x00010000)
-
-#define BCSR2_FLASH_PD_MASK ((uint)0xF0000000)
-#define BCSR2_DRAM_PD_MASK ((uint)0x07800000)
-#define BCSR2_DRAM_PD_SHIFT (23)
-#define BCSR2_EXTTOLI_MASK ((uint)0x00780000)
-#define BCSR2_DBREVNR_MASK ((uint)0x00030000)
-
-#define BCSR3_DBID_MASK ((ushort)0x3800)
-#define BCSR3_CNT_REG_EN_PROTECT ((ushort)0x0400)
-#define BCSR3_BREVNR0 ((ushort)0x0080)
-#define BCSR3_FLASH_PD_MASK ((ushort)0x0070)
-#define BCSR3_BREVN1 ((ushort)0x0008)
-#define BCSR3_BREVN2_MASK ((ushort)0x0003)
-
-/* We don't use the 8259.
- */
-#define NR_8259_INTS 0
-
-/* Machine type
- */
-#define _MACH_8xx (_MACH_ads)
-
-#endif /* _CONFIG_ADS860_H */
+#endif /* __CONFIG_H */
#endif
/*------------------------------------------------------------------------
- * Ethernet -- needs work!
+ * Ethernet
*----------------------------------------------------------------------*/
#if (CFG_NIOS_CPU_LAN_NUMS == 1)
#endif /* CFG_NIOS_CPU_PIO_NUMS */
+/*------------------------------------------------------------------------
+ * ASMI - Active Serial Memory Interface.
+ *
+ * ASMI is for Cyclone devices only and only works when the configuration
+ * is loaded via JTAG or ASMI. Please see doc/README.dk1c20 for details.
+ *----------------------------------------------------------------------*/
+#define CONFIG_NIOS_ASMI /* Enable ASMI */
+#define CFG_NIOS_ASMIBASE 0x00920b00 /* ASMI base address */
+
/*------------------------------------------------------------------------
* COMMANDS
*----------------------------------------------------------------------*/
--- /dev/null
+/*
+ * A collection of structures, addresses, and values associated with
+ * the Motorola DUET ADS board. Values common to all FADS family boards
+ * are in board/fads/fads.h
+ *
+ * Copyright (C) 2003 Arabella Software Ltd.
+ * Yuli Barcohen <yuli@arabellasw.com>
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* Board type */
+#define CONFIG_DUET_ADS 1 /* Duet (MPC87x/88x) ADS */
+#define CONFIG_FADS 1 /* We are FADS compatible (more or less) */
+
+#define CONFIG_MPC885 1 /* MPC885 CPU (Duet family) */
+
+#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
+#undef CONFIG_8xx_CONS_SMC2
+#undef CONFIG_8xx_CONS_NONE
+#define CONFIG_BAUDRATE 38400
+
+#define CFG_8XX_FACT 5 /* Multiply by 5 */
+#define CFG_8XX_XIN 10000000 /* 10 MHz in */
+
+#define CONFIG_SDRAM_50MHZ 1
+
+/*-----------------------------------------------------------------------
+ * PLPRCR - PLL, Low-Power, and Reset Control Register 14-22
+ *-----------------------------------------------------------------------
+ * set the PLL, the low-power modes and the reset control
+ */
+#define CFG_PLPRCR ((CFG_8XX_FACT << PLPRCR_MFI_SHIFT) | PLPRCR_TEXPS)
+
+#include "fads.h"
+
+#define CFG_PHYDEV_ADDR (BCSR_ADDR + 0x20000)
+
+#define CFG_OR5_PRELIM 0xFFFF8110 /* 64Kbyte address space */
+#define CFG_BR5_PRELIM (CFG_PHYDEV_ADDR | BR_PS_8 | BR_V)
+
+#define BCSR5 (CFG_PHYDEV_ADDR + 0x300)
+
+#define BCSR5_MII2_EN 0x40
+#define BCSR5_MII2_RST 0x20
+#define BCSR5_T1_RST 0x10
+#define BCSR5_ATM155_RST 0x08
+#define BCSR5_ATM25_RST 0x04
+#define BCSR5_MII1_EN 0x02
+#define BCSR5_MII1_RST 0x01
+
+#endif /* __CONFIG_H */
* High Level Configuration Options
* (easy to change)
*/
-#include <mpc8xx_irq.h>
-
#define CONFIG_MPC823 1
#define CONFIG_MPC823FADS 1
#define CONFIG_FADS 1
#define CONFIG_DRAM_50MHZ 1
#define CONFIG_SDRAM_50MHZ
-#ifdef CONFIG_MPC860T
-
-/* Interrupt level assignments.
-*/
-#define FEC_INTERRUPT SIU_LEVEL1 /* FEC interrupt */
-
-#endif /* CONFIG_MPC860T */
-
/* We don't use the 8259.
*/
#define NR_8259_INTS 0
#define PCMCIA_SLOT_A 1
#endif
+#define CFG_DAUGHTERBOARD
+
#endif /* __CONFIG_H */
* High Level Configuration Options
* (easy to change)
*/
-#include <mpc8xx_irq.h>
-
#define CONFIG_MPC850 1
#define CONFIG_MPC850SAR 1
#define CONFIG_FADS 1
#define CONFIG_DRAM_50MHZ 1
#define CONFIG_SDRAM_50MHZ
-#ifdef CONFIG_MPC860T
-
-/* Interrupt level assignments.
-*/
-#define FEC_INTERRUPT SIU_LEVEL1 /* FEC interrupt */
-
-#endif /* CONFIG_MPC860T */
-
/* We don't use the 8259.
*/
#define NR_8259_INTS 0
#define PCMCIA_SLOT_A 1
#endif
+#define CFG_DAUGHTERBOARD
+
#endif /* __CONFIG_H */
* Helmut Buchsbaum added bitvalues for BCSRx
*
* Copyright (c) 1998 Dan Malek (dmalek@jlc.net)
+ *
+ * Modified by, Yuli Barcohen, Arabella Software Ltd., yuli@arabellasw.com
+ *
+ * Values common to all FADS family boards are in board/fads/fads.h
*/
-/*
- * 1999-nov-26: The FADS is using the following physical memorymap:
- *
- * ff020000 -> ff02ffff : pcmcia
- * ff010000 -> ff01ffff : BCSR connected to CS1, setup by 8xxrom
- * ff000000 -> ff00ffff : IMAP internal in the cpu
- * fe000000 -> ffnnnnnn : flash connected to CS0, setup by 8xxrom
- * 00000000 -> nnnnnnnn : sdram/dram setup by 8xxrom
- */
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
#ifndef __CONFIG_H
#define __CONFIG_H
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
/* board type */
#define CONFIG_FADS 1 /* old/new FADS + new ADS */
# define CFG_8XX_XIN 5000000 /* 5 MHz in */
#endif
-#define MPC8XX_HZ ((CFG_8XX_XIN) * (CFG_8XX_FACT))
-
-/* should ALWAYS define this, measure_gclk in speed.c is unreliable */
-/* in general, we always know this for FADS+new ADS anyway */
-#define CONFIG_8xx_GCLK_FREQ MPC8XX_HZ
-
-#if 1
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
-
-#undef CONFIG_BOOTARGS
-#define CONFIG_BOOTCOMMAND \
- "bootp; " \
- "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; " \
- "bootm"
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/* ATA / IDE and partition support */
-#define CONFIG_MAC_PARTITION 1
-#define CONFIG_DOS_PARTITION 1
-#define CONFIG_ISO_PARTITION 1
-#undef CONFIG_ATAPI
-#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
-#undef CONFIG_IDE_LED /* LED for ide not supported */
-#undef CONFIG_IDE_RESET /* reset for ide not supported */
-
-/* choose SCC1 ethernet (10BASET on motherboard)
- * or FEC ethernet (10/100 on daughterboard)
- */
-#if 0
-#define CONFIG_SCC1_ENET 1 /* use SCC1 ethernet */
-#undef CONFIG_FEC_ENET /* disable FEC ethernet */
-#else /* all 86x cores have FECs, if in doubt, use it */
-#undef CONFIG_SCC1_ENET /* disable SCC1 ethernet */
-#define CONFIG_FEC_ENET 1 /* use FEC ethernet */
-#define CFG_DISCOVER_PHY
-#endif
-#if defined(CONFIG_SCC1_ENET) && defined(CONFIG_FEC_ENET)
-#error Both CONFIG_SCC1_ENET and CONFIG_FEC_ENET configured
-#endif
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
-
-/*
- * Miscellaneous configurable options
- */
-#undef CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=>" /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0100000 /* memtest works on */
-#if (CFG_SDRAM_SIZE)
-#define CFG_MEMTEST_END CFG_SDRAM_SIZE /* 1 ... SDRAM_SIZE */
-#else
-#define CFG_MEMTEST_END 0x0400000 /* 1 ... 4 MB in DRAM */
-#endif
-
-#define CFG_LOAD_ADDR 0x00100000
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CFG_IMMR 0xFF000000
-#define CFG_IMMR_SIZE ((uint)(64 * 1024))
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CFG_INIT_RAM_ADDR CFG_IMMR
-#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
-#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
- */
-#define CFG_SDRAM_BASE 0x00000000
-#ifdef CONFIG_FADS
-# define CFG_SDRAM_SIZE 0x00400000 /* 4 meg */
-#else /* !CONFIG_FADS */ /* old ADS */
-# define CFG_SDRAM_SIZE 0x00000000 /* NO SDRAM */
-#endif
-
-#define CFG_FLASH_BASE TEXT_BASE
-
-#define CFG_FLASH_SIZE ((uint)(8 * 1024 * 1024)) /* max 8Mbyte */
-
-#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CFG_MONITOR_BASE CFG_FLASH_BASE
-#define CFG_MALLOC_LEN (384 << 10) /* Reserve 384 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 16 /* max number of sectors on one chip */
-
-#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_OFFSET 0x00040000
-#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
-
-#define CFG_ENV_SECT_SIZE 0x40000 /* see README - env sector total size */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control 11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
- SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration 11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control 11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CFG_PISCR (PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
- *-----------------------------------------------------------------------
- * set the PLL, the low-power modes and the reset control (15-29)
- */
-#define CFG_PLPRCR (((CFG_8XX_FACT-1) << PLPRCR_MF_SHIFT) | \
- PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register 15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK SCCR_EBDF11
-#define CFG_SCCR (SCCR_TBS|SCCR_COM00|SCCR_DFSYNC00|SCCR_DFBRG00|SCCR_DFNL000|SCCR_DFNH000|SCCR_DFLCD000|SCCR_DFALCD00)
-
- /*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CFG_DER 0
-
-/* Because of the way the 860 starts up and assigns CS0 the
-* entire address space, we have to set the memory controller
-* differently. Normally, you write the option register
-* first, and then enable the chip select by writing the
-* base register. For CS0, you must write the base register
-* first, followed by the option register.
-*/
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-/* the other CS:s are determined by looking at parameters in BCSRx */
-
-#define BCSR_ADDR ((uint) 0xFF010000)
-#define BCSR_SIZE ((uint)(64 * 1024))
+#define CONFIG_DRAM_50MHZ 1
+#define CONFIG_SDRAM_50MHZ 1
-#define CFG_PRELIM_OR_AM 0xFF800000 /* OR addr mask */
+#include "fads.h"
-/* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0 */
-#define CFG_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK | OR_TRLX)
+#define CFG_PLPRCR (((CFG_8XX_FACT-1) << PLPRCR_MF_SHIFT) | \
+ PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
#ifdef USE_REAL_FLASH_VALUES
/*
* These values fit our FADS860T ...
* The "default" behaviour with 1Mbyte initial doesn't work for us!
*/
+#undef CFG_OR0_PRELIM
+#undef CFG_BR0_PRELIM
#define CFG_OR0_PRELIM 0x0FFC00D34 /* Real values for the board */
#define CFG_BR0_PRELIM 0x02800001 /* Real values for the board */
-#else
-#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH) /* 8 Mbyte until detected */
-#define CFG_BR0_PRELIM ((CFG_FLASH_BASE & BR_BA_MSK) | BR_V )
-#endif
-
-/* BCSRx - Board Control and Status Registers */
-#define CFG_OR1_PRELIM 0xffff8110 /* 64Kbyte address space */
-#define CFG_BR1_PRELIM ((BCSR_ADDR) | BR_V )
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-
-/* values according to the manual */
-
-
-#define PCMCIA_MEM_ADDR ((uint)0xff020000)
-#define PCMCIA_MEM_SIZE ((uint)(64 * 1024))
-
-#define BCSR0 ((uint) (BCSR_ADDR + 0x00))
-#define BCSR1 ((uint) (BCSR_ADDR + 0x04))
-#define BCSR2 ((uint) (BCSR_ADDR + 0x08))
-#define BCSR3 ((uint) (BCSR_ADDR + 0x0c))
-#define BCSR4 ((uint) (BCSR_ADDR + 0x10))
-
-/* FADS bitvalues by Helmut Buchsbaum
- * see MPC8xxADS User's Manual for a proper description
- * of the following structures
- */
-
-#define BCSR0_ERB ((uint)0x80000000)
-#define BCSR0_IP ((uint)0x40000000)
-#define BCSR0_BDIS ((uint)0x10000000)
-#define BCSR0_BPS_MASK ((uint)0x0C000000)
-#define BCSR0_ISB_MASK ((uint)0x01800000)
-#define BCSR0_DBGC_MASK ((uint)0x00600000)
-#define BCSR0_DBPC_MASK ((uint)0x00180000)
-#define BCSR0_EBDF_MASK ((uint)0x00060000)
-
-#define BCSR1_FLASH_EN ((uint)0x80000000)
-#define BCSR1_DRAM_EN ((uint)0x40000000)
-#define BCSR1_ETHEN ((uint)0x20000000)
-#define BCSR1_IRDEN ((uint)0x10000000)
-#define BCSR1_FLASH_CFG_EN ((uint)0x08000000)
-#define BCSR1_CNT_REG_EN_PROTECT ((uint)0x04000000)
-#define BCSR1_BCSR_EN ((uint)0x02000000)
-#define BCSR1_RS232EN_1 ((uint)0x01000000)
-#define BCSR1_PCCEN ((uint)0x00800000)
-#define BCSR1_PCCVCC0 ((uint)0x00400000)
-#define BCSR1_PCCVPP_MASK ((uint)0x00300000)
-#define BCSR1_DRAM_HALF_WORD ((uint)0x00080000)
-#define BCSR1_RS232EN_2 ((uint)0x00040000)
-#define BCSR1_SDRAM_EN ((uint)0x00020000)
-#define BCSR1_PCCVCC1 ((uint)0x00010000)
-
-#define BCSR2_FLASH_PD_MASK ((uint)0xF0000000)
-#define BCSR2_DRAM_PD_MASK ((uint)0x07800000)
-#define BCSR2_DRAM_PD_SHIFT (23)
-#define BCSR2_EXTTOLI_MASK ((uint)0x00780000)
-#define BCSR2_DBREVNR_MASK ((uint)0x00030000)
-
-#define BCSR3_DBID_MASK ((ushort)0x3800)
-#define BCSR3_CNT_REG_EN_PROTECT ((ushort)0x0400)
-#define BCSR3_BREVNR0 ((ushort)0x0080)
-#define BCSR3_FLASH_PD_MASK ((ushort)0x0070)
-#define BCSR3_BREVN1 ((ushort)0x0008)
-#define BCSR3_BREVN2_MASK ((ushort)0x0003)
-
-#define BCSR4_ETHLOOP ((uint)0x80000000)
-#define BCSR4_TFPLDL ((uint)0x40000000)
-#define BCSR4_TPSQEL ((uint)0x20000000)
-#define BCSR4_SIGNAL_LAMP ((uint)0x10000000)
-#ifdef CONFIG_MPC823
-#define BCSR4_USB_EN ((uint)0x08000000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860SAR
-#define BCSR4_UTOPIA_EN ((uint)0x08000000)
-#endif /* CONFIG_MPC860SAR */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETH_EN ((uint)0x08000000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
-#define BCSR4_USB_SPEED ((uint)0x04000000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETHCFG0 ((uint)0x04000000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
-#define BCSR4_VCCO ((uint)0x02000000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETHFDE ((uint)0x02000000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
-#define BCSR4_VIDEO_ON ((uint)0x00800000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC823
-#define BCSR4_VDO_EKT_CLK_EN ((uint)0x00400000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETHCFG1 ((uint)0x00400000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
-#define BCSR4_VIDEO_RST ((uint)0x00200000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETHRST ((uint)0x00200000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
-#define BCSR4_MODEM_EN ((uint)0x00100000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC823
-#define BCSR4_DATA_VOICE ((uint)0x00080000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC850
-#define BCSR4_DATA_VOICE ((uint)0x00080000)
-#endif /* CONFIG_MPC850 */
-
-#define CONFIG_DRAM_50MHZ 1
-#define CONFIG_SDRAM_50MHZ 1
-
-/* We don't use the 8259.
-*/
-#define NR_8259_INTS 0
-
-/* Machine type
-*/
-#define _MACH_8xx (_MACH_fads)
-
-#define CONFIG_DISK_SPINUP_TIME 1000000
-
-
-/* PCMCIA configuration */
-
-#ifdef CONFIG_MPC860
-#define PCMCIA_SLOT_A 1
#endif
-/*#define CFG_PCMCIA_MEM_SIZE ( 64 << 20) */
-#define CFG_PCMCIA_MEM_ADDR (0x50000000)
-#define CFG_PCMCIA_MEM_SIZE ( 64 << 20 )
-#define CFG_PCMCIA_DMA_ADDR (0x54000000)
-#define CFG_PCMCIA_DMA_SIZE ( 64 << 20 )
-#define CFG_PCMCIA_ATTRB_ADDR (0x58000000)
-#define CFG_PCMCIA_ATTRB_SIZE ( 64 << 20 )
-#define CFG_PCMCIA_IO_ADDR (0x5C000000)
-#define CFG_PCMCIA_IO_SIZE ( 64 << 20 )
-/* we have 8 windows, we take everything up to 60000000 */
-
-#define CFG_ATA_IDE0_OFFSET 0x0000
-
-#define CFG_ATA_BASE_ADDR CFG_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O */
-#define CFG_ATA_DATA_OFFSET (CFG_PCMCIA_MEM_SIZE + 0x320)
-/* Offset for normal register accesses */
-#define CFG_ATA_REG_OFFSET (2 * CFG_PCMCIA_MEM_SIZE + 0x320)
-/* Offset for alternate registers */
-#define CFG_ATA_ALT_OFFSET 0x0000
-/*#define CFG_ATA_ALT_OFFSET 0x0100 */
+#define CFG_DAUGHTERBOARD /* FADS has processor-specfic daughterboard */
#endif /* __CONFIG_H */
* the Motorola MPC8xxADS board. Copied from the FADS config.
*
* Copyright (c) 1998 Dan Malek (dmalek@jlc.net)
+ *
+ * Modified by, Yuli Barcohen, Arabella Software Ltd., yuli@arabellasw.com
+ *
+ * Values common to all FADS family boards are in board/fads/fads.h
*/
-/*
- * 1999-nov-26: The FADS is using the following physical memorymap:
- *
- * ff020000 -> ff02ffff : pcmcia
- * ff010000 -> ff01ffff : BCSR connected to CS1
- * ff000000 -> ff00ffff : IMAP internal in the cpu
- * fe000000 -> fennnnnn : flash connected to CS0
- * 00000000 -> nnnnnnnn : sdram connected to CS4
- */
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
#ifndef __CONFIG_H
#define __CONFIG_H
#define CONFIG_MPC86xADS 1 /* new ADS */
#define CONFIG_FADS 1 /* We are FADS compatible (more or less) */
-/* new 86xADS only - pick one of these */
+/* New MPC86xADS - pick one of these */
#define CONFIG_MPC866T 1
#undef CONFIG_MPC866P
#undef CONFIG_MPC859T
#undef CONFIG_8xx_CONS_SMC2
#undef CONFIG_8xx_CONS_NONE
#define CONFIG_BAUDRATE 38400
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#ifdef CONFIG_MPC86xADS
# define CFG_8XX_FACT 5 /* Multiply by 5 */
# define CFG_8XX_XIN 10000000 /* 10 MHz in */
-#else /* ! CONFIG_MPC86xADS */
-# if 0 /* old FADS */
-# define CFG_8XX_FACT 12 /* Multiply by 12 */
-# define CFG_8XX_XIN 4000000 /* 4 MHz in */
-# else /* new FADS */
-# define CFG_8XX_FACT 10 /* Multiply by 10 */
-# define CFG_8XX_XIN 5000000 /* 5 MHz in */
-# endif
-#endif /* ! CONFIG_MPC86xADS */
-
-#define MPC8XX_HZ ((CFG_8XX_XIN) * (CFG_8XX_FACT))
-
-/* should ALWAYS define this, measure_gclk in speed.c is unreliable */
-/* in general, we always know this for FADS+new ADS anyway */
-#define CONFIG_8xx_GCLK_FREQ MPC8XX_HZ
-
-#if 1
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
-
-#undef CONFIG_BOOTARGS
-#define CONFIG_BOOTCOMMAND \
- "dhcp;" \
- "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \
- "bootm"
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-/* ATA / IDE and partition support */
-#define CONFIG_MAC_PARTITION 1
-#define CONFIG_DOS_PARTITION 1
-#define CONFIG_ISO_PARTITION 1
-#undef CONFIG_ATAPI
-#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
-#undef CONFIG_IDE_LED /* LED for ide not supported */
-#undef CONFIG_IDE_RESET /* reset for ide not supported */
-
-/*
- * New MPC86xADS provides two Ethernet connectivity options:
- * 10Mbit/s on SCC1 and 100Mbit/s on FEC. All new PQ1 chips
- * has got FEC so FEC is the default.
- */
-#undef CONFIG_SCC1_ENET /* disable SCC1 ethernet */
-#define CONFIG_FEC_ENET 1 /* use FEC ethernet */
-#ifdef CONFIG_FEC_ENET
-#define CFG_DISCOVER_PHY
-#endif
-#if defined(CONFIG_SCC1_ENET) && defined(CONFIG_FEC_ENET)
-#error Both CONFIG_SCC1_ENET and CONFIG_FEC_ENET configured
-#endif
-
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
- | CFG_CMD_DHCP \
- | CFG_CMD_IMMAP \
- | CFG_CMD_MII \
- | CFG_CMD_PING \
- )
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
-
-/*
- * Miscellaneous configurable options
- */
-#undef CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=>" /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_LOAD_ADDR 0x00100000
-
-#define CFG_HZ 1000 /* decr freq: 1 ms ticks */
-
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CFG_IMMR 0xFF000000
-#define CFG_IMMR_SIZE ((uint)(64 * 1024))
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CFG_INIT_RAM_ADDR CFG_IMMR
-#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
-#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
- */
-#define CFG_SDRAM_BASE 0x00000000
-#if defined(CONFIG_MPC86xADS) /* new ADS */
-#define CFG_SDRAM_SIZE 0x00800000 /* 8 meg */
-#elif defined(CONFIG_FADS) /* old/new FADS */
-#define CFG_SDRAM_SIZE 0x00400000 /* 4 meg */
-#else /* old ADS */
-#define CFG_SDRAM_SIZE 0x00000000 /* No SDRAM */
-#endif
-
-#define CFG_MEMTEST_START 0x0100000 /* memtest works on */
-#if (CFG_SDRAM_SIZE)
-#define CFG_MEMTEST_END CFG_SDRAM_SIZE /* 1 ... SDRAM_SIZE */
-#else
-#define CFG_MEMTEST_END 0x0400000 /* 1 ... 4 MB in DRAM */
-#endif /* CFG_SDRAM_SIZE */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CFG_FLASH_BASE TEXT_BASE
-#define CFG_FLASH_SIZE ((uint)(8 * 1024 * 1024)) /* max 8Mbyte */
-
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 16 /* max number of sectors on one chip */
-
-#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_SECT_SIZE 0x40000 /* see README - env sector total size */
-#define CFG_ENV_OFFSET CFG_ENV_SECT_SIZE
-#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment */
-
-#define CFG_MONITOR_BASE CFG_FLASH_BASE
-#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 KB for monitor */
-#define CFG_MALLOC_LEN (384 << 10) /* Reserve 384 kB for malloc() */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control 11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
- SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
+#define CONFIG_DRAM_50MHZ 1
+#define CONFIG_SDRAM_50MHZ 1
/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration 11-6
+ * PLPRCR - PLL, Low-Power, and Reset Control Register 14-22
*-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
+ * set the PLL, the low-power modes and the reset control
*/
-#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control 11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CFG_PISCR (PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
- *-----------------------------------------------------------------------
- * set the PLL, the low-power modes and the reset control (15-29)
- */
-#define CFG_PLPRCR ((CFG_8XX_FACT << PLPRCR_MFI_SHIFT) | \
- PLPRCR_SPLSS | PLPRCR_TEXPS)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register 15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK SCCR_EBDF11
-#define CFG_SCCR (SCCR_TBS|SCCR_COM00|SCCR_DFSYNC00|SCCR_DFBRG00|SCCR_DFNL000|SCCR_DFNH000|SCCR_DFLCD000|SCCR_DFALCD00)
-
- /*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CFG_DER 0
-
-/* Because of the way the 860 starts up and assigns CS0 the
-* entire address space, we have to set the memory controller
-* differently. Normally, you write the option register
-* first, and then enable the chip select by writing the
-* base register. For CS0, you must write the base register
-* first, followed by the option register.
-*/
-
-/*
- * Init Memory Controller:
- *
- * BR0/OR0 (Flash)
- * BR1/OR1 (BCSR)
- */
-/* the other CS:s are determined by looking at parameters in BCSRx */
-
-#define BCSR_ADDR ((uint) 0xFF010000)
-#define BCSR_SIZE ((uint)(64 * 1024))
-
-#define CFG_PRELIM_OR_AM 0xFF800000 /* OR addr mask */
-
-/* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0 */
-#define CFG_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK | OR_TRLX)
-
-#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH) /* 8 Mbyte until detected */
-#define CFG_BR0_PRELIM ((CFG_FLASH_BASE & BR_BA_MSK) | BR_V )
-
-/* BCSRx - Board Control and Status Registers */
-#define CFG_OR1_PRELIM 0xffff8110 /* 64Kbyte address space */
-#define CFG_BR1_PRELIM ((BCSR_ADDR) | BR_V )
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-/* values according to the manual */
-
-#define PCMCIA_MEM_ADDR ((uint)0xff020000)
-#define PCMCIA_MEM_SIZE ((uint)(64 * 1024))
-
-#define BCSR0 ((uint) (BCSR_ADDR + 0x00))
-#define BCSR1 ((uint) (BCSR_ADDR + 0x04))
-#define BCSR2 ((uint) (BCSR_ADDR + 0x08))
-#define BCSR3 ((uint) (BCSR_ADDR + 0x0c))
-#define BCSR4 ((uint) (BCSR_ADDR + 0x10))
-
-/* FADS bitvalues by Helmut Buchsbaum
- * see MPC8xxADS User's Manual for a proper description
- * of the following structures
- */
-
-#define BCSR0_ERB ((uint)0x80000000)
-#define BCSR0_IP ((uint)0x40000000)
-#define BCSR0_BDIS ((uint)0x10000000)
-#define BCSR0_BPS_MASK ((uint)0x0C000000)
-#define BCSR0_ISB_MASK ((uint)0x01800000)
-#define BCSR0_DBGC_MASK ((uint)0x00600000)
-#define BCSR0_DBPC_MASK ((uint)0x00180000)
-#define BCSR0_EBDF_MASK ((uint)0x00060000)
-
-#define BCSR1_FLASH_EN ((uint)0x80000000)
-#define BCSR1_DRAM_EN ((uint)0x40000000)
-#define BCSR1_ETHEN ((uint)0x20000000)
-#define BCSR1_IRDEN ((uint)0x10000000)
-#define BCSR1_FLASH_CFG_EN ((uint)0x08000000)
-#define BCSR1_CNT_REG_EN_PROTECT ((uint)0x04000000)
-#define BCSR1_BCSR_EN ((uint)0x02000000)
-#define BCSR1_RS232EN_1 ((uint)0x01000000)
-#define BCSR1_PCCEN ((uint)0x00800000)
-#define BCSR1_PCCVCC0 ((uint)0x00400000)
-#define BCSR1_PCCVPP_MASK ((uint)0x00300000)
-#define BCSR1_DRAM_HALF_WORD ((uint)0x00080000)
-#define BCSR1_RS232EN_2 ((uint)0x00040000)
-#define BCSR1_SDRAM_EN ((uint)0x00020000)
-#define BCSR1_PCCVCC1 ((uint)0x00010000)
-
-#define BCSR2_FLASH_PD_MASK ((uint)0xF0000000)
-#define BCSR2_DRAM_PD_MASK ((uint)0x07800000)
-#define BCSR2_DRAM_PD_SHIFT (23)
-#define BCSR2_EXTTOLI_MASK ((uint)0x00780000)
-#define BCSR2_DBREVNR_MASK ((uint)0x00030000)
-
-#define BCSR3_DBID_MASK ((ushort)0x3800)
-#define BCSR3_CNT_REG_EN_PROTECT ((ushort)0x0400)
-#define BCSR3_BREVNR0 ((ushort)0x0080)
-#define BCSR3_FLASH_PD_MASK ((ushort)0x0070)
-#define BCSR3_BREVN1 ((ushort)0x0008)
-#define BCSR3_BREVN2_MASK ((ushort)0x0003)
-
-#define BCSR4_ETHLOOP ((uint)0x80000000)
-#define BCSR4_TFPLDL ((uint)0x40000000)
-#define BCSR4_TPSQEL ((uint)0x20000000)
-#define BCSR4_SIGNAL_LAMP ((uint)0x10000000)
-#define BCSR4_FETH_EN ((uint)0x08000000)
-#define BCSR4_FETHCFG0 ((uint)0x04000000)
-#define BCSR4_FETHFDE ((uint)0x02000000)
-#define BCSR4_FETHCFG1 ((uint)0x00400000)
-#define BCSR4_FETHRST ((uint)0x00200000)
-
-#define CONFIG_DRAM_50MHZ 1
-#define CONFIG_SDRAM_50MHZ 1
-
-/* We don't use the 8259.
-*/
-#define NR_8259_INTS 0
-
-/* Machine type
-*/
-#define _MACH_8xx (_MACH_fads)
-
-#define CONFIG_DISK_SPINUP_TIME 1000000
-
-
-/* PCMCIA configuration */
-
-#ifdef CONFIG_MPC860
-#define PCMCIA_SLOT_A 1
-#endif
-
-#define CFG_PCMCIA_MEM_ADDR (0x50000000)
-#define CFG_PCMCIA_MEM_SIZE ( 64 << 20 )
-#define CFG_PCMCIA_DMA_ADDR (0x54000000)
-#define CFG_PCMCIA_DMA_SIZE ( 64 << 20 )
-#define CFG_PCMCIA_ATTRB_ADDR (0x58000000)
-#define CFG_PCMCIA_ATTRB_SIZE ( 64 << 20 )
-#define CFG_PCMCIA_IO_ADDR (0x5C000000)
-#define CFG_PCMCIA_IO_SIZE ( 64 << 20 )
-/* we have 8 windows, we take everything up to 60000000 */
-
-#define CFG_ATA_IDE0_OFFSET 0x0000
-
-#define CFG_ATA_BASE_ADDR CFG_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O */
-#define CFG_ATA_DATA_OFFSET (CFG_PCMCIA_MEM_SIZE + 0x320)
-/* Offset for normal register accesses */
-#define CFG_ATA_REG_OFFSET (2 * CFG_PCMCIA_MEM_SIZE + 0x320)
-/* Offset for alternate registers */
-#define CFG_ATA_ALT_OFFSET 0x0000
-/*#define CFG_ATA_ALT_OFFSET 0x0100 */
+#define CFG_PLPRCR ((CFG_8XX_FACT << PLPRCR_MFI_SHIFT) | PLPRCR_TEXPS)
+#include "fads.h"
#endif /* __CONFIG_H */
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#if 1 /* test-only */
+
#define CONFIG_NO_SERIAL_EEPROM
/*#undef CONFIG_NO_SERIAL_EEPROM*/
/*--------------------------------------------------------------------*/
#define PLL_PCIDIV_3 0x00000002
#define PLL_PCIDIV_4 0x00000003
-/*
-!-----------------------------------------------------------------------
-! PLL settings for 266MHz CPU, 133MHz PLB/SDRAM, 66MHz EBC, 33MHz PCI,
-! assuming a 33.3MHz input clock to the 405EP.
-!-----------------------------------------------------------------------
-*/
-#define PLLMR0_133_66_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_1 | \
+/* CPU - PLB/SDRAM - EBC - OPB - PCI (assuming a 33.3MHz input clock to the 405EP) */
+#define PLLMR0_133_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_1 | \
PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \
PLL_MALDIV_1 | PLL_PCIDIV_4)
-#define PLLMR1_133_66_66_33 (PLL_FBKDIV_4 | \
+#define PLLMR1_133_133_33_66_33 (PLL_FBKDIV_4 | \
PLL_FWDDIVA_6 | PLL_FWDDIVB_6 | \
PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW)
#define PLLMR0_200_100_50_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \
#define PLLMR1_200_100_50_33 (PLL_FBKDIV_6 | \
PLL_FWDDIVA_4 | PLL_FWDDIVB_4 | \
PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW)
-#define PLLMR0_266_133_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \
+#define PLLMR0_266_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \
PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \
PLL_MALDIV_1 | PLL_PCIDIV_4)
-#define PLLMR1_266_133_66_33 (PLL_FBKDIV_8 | \
+#define PLLMR1_266_133_33_66_33 (PLL_FBKDIV_8 | \
PLL_FWDDIVA_3 | PLL_FWDDIVB_3 | \
PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW)
-#if 0 /* test-only */
-#define PLLMR0_DEFAULT PLLMR0_266_133_66_33
-#define PLLMR1_DEFAULT PLLMR1_266_133_66_33
-#endif
-#if 0 /* test-only */
-#define PLLMR0_DEFAULT PLLMR0_200_100_50_33
-#define PLLMR1_DEFAULT PLLMR1_200_100_50_33
-#endif
-#if 1 /* test-only */
-#define PLLMR0_DEFAULT PLLMR0_133_66_66_33
-#define PLLMR1_DEFAULT PLLMR1_133_66_66_33
-#endif
+#define PLLMR0_333_111_37_55_55 (PLL_CPUDIV_1 | PLL_PLBDIV_3 | \
+ PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \
+ PLL_MALDIV_1 | PLL_PCIDIV_2)
+#define PLLMR1_333_111_37_55_55 (PLL_FBKDIV_10 | \
+ PLL_FWDDIVA_3 | PLL_FWDDIVB_3 | \
+ PLL_TUNE_15_M_40 | PLL_TUNE_VCO_HI)
+
+#if (CONFIG_PPCHAMELEON_MODULE_MODEL == CONFIG_PPCHAMELEON_MODULE_HI)
+/* Model HI */
+#define PLLMR0_DEFAULT PLLMR0_333_111_37_55_55
+#define PLLMR1_DEFAULT PLLMR1_333_111_37_55_55
+/* Model ME */
+#elif (CONFIG_PPCHAMELEON_MODULE_MODEL == CONFIG_PPCHAMELEON_MODULE_ME)
+#define PLLMR0_DEFAULT PLLMR0_266_133_33_66_33
+#define PLLMR1_DEFAULT PLLMR1_266_133_33_66_33
+#else
+/* Model BA (default) */
+#define PLLMR0_DEFAULT PLLMR0_133_133_33_66_33
+#define PLLMR1_DEFAULT PLLMR1_133_133_33_66_33
#endif
-#endif
+
+#endif /* CONFIG_NO_SERIAL_EEPROM */
#define CFG_OPB_FREQ 50000000
#ifndef __CRAMFS_H
#define __CRAMFS_H
-#ifndef __KERNEL__
-
-typedef unsigned char u8;
-typedef unsigned short u16;
-typedef unsigned int u32;
-
-#endif
-
#define CRAMFS_MAGIC 0x28cd3d45 /* some random number */
#define CRAMFS_SIGNATURE "Compressed ROMFS"
* Width of various bitfields in struct cramfs_inode.
* Primarily used to generate warnings in mkcramfs.
*/
-#define CRAMFS_MODE_WIDTH 16
-#define CRAMFS_UID_WIDTH 16
-#define CRAMFS_SIZE_WIDTH 24
-#define CRAMFS_GID_WIDTH 8
-#define CRAMFS_NAMELEN_WIDTH 6
-#define CRAMFS_OFFSET_WIDTH 26
+#define CRAMFS_MODE_WIDTH 16
+#define CRAMFS_UID_WIDTH 16
+#define CRAMFS_SIZE_WIDTH 24
+#define CRAMFS_GID_WIDTH 8
+#define CRAMFS_NAMELEN_WIDTH 6
+#define CRAMFS_OFFSET_WIDTH 26
/*
* Since inode.namelen is a unsigned 6-bit number, the maximum cramfs
*/
struct cramfs_inode {
u32 mode:CRAMFS_MODE_WIDTH, uid:CRAMFS_UID_WIDTH;
+
/* SIZE for device files is i_rdev */
u32 size:CRAMFS_SIZE_WIDTH, gid:CRAMFS_GID_WIDTH;
+
/* NAMELEN is the length of the file name, divided by 4 and
rounded up. (cramfs doesn't support hard links.) */
/* OFFSET: For symlinks and non-empty regular files, this
| CRAMFS_FLAG_WRONG_SIGNATURE \
| CRAMFS_FLAG_SHIFTED_ROOT_OFFSET )
+/*
+ * Since cramfs is little-endian, provide macros to swab the bitfields.
+ */
+
+#ifndef __BYTE_ORDER
+#if defined(__LITTLE_ENDIAN) && !defined(__BIG_ENDIAN)
+#define __BYTE_ORDER __LITTLE_ENDIAN
+#elif defined(__BIG_ENDIAN) && !defined(__LITTLE_ENDIAN)
+#define __BYTE_ORDER __BIG_ENDIAN
+#else
+#error "unable to define __BYTE_ORDER"
+#endif
+#endif /* not __BYTE_ORDER */
+
+#if __BYTE_ORDER == __LITTLE_ENDIAN
+#define CRAMFS_16(x) (x)
+#define CRAMFS_24(x) (x)
+#define CRAMFS_32(x) (x)
+#define CRAMFS_GET_NAMELEN(x) ((x)->namelen)
+#define CRAMFS_GET_OFFSET(x) ((x)->offset)
+#define CRAMFS_SET_OFFSET(x,y) ((x)->offset = (y))
+#define CRAMFS_SET_NAMELEN(x,y) ((x)->namelen = (y))
+#elif __BYTE_ORDER == __BIG_ENDIAN
+#ifdef __KERNEL__
+#define CRAMFS_16(x) swab16(x)
+#define CRAMFS_24(x) ((swab32(x)) >> 8)
+#define CRAMFS_32(x) swab32(x)
+#else /* not __KERNEL__ */
+#define CRAMFS_16(x) bswap_16(x)
+#define CRAMFS_24(x) ((bswap_32(x)) >> 8)
+#define CRAMFS_32(x) bswap_32(x)
+#endif /* not __KERNEL__ */
+#define CRAMFS_GET_NAMELEN(x) (((u8*)(x))[8] & 0x3f)
+#define CRAMFS_GET_OFFSET(x) ((CRAMFS_24(((u32*)(x))[2] & 0xffffff) << 2) |\
+ ((((u32*)(x))[2] & 0xc0000000) >> 30))
+#define CRAMFS_SET_NAMELEN(x,y) (((u8*)(x))[8] = (((0x3f & (y))) | \
+ (0xc0 & ((u8*)(x))[8])))
+#define CRAMFS_SET_OFFSET(x,y) (((u32*)(x))[2] = (((y) & 3) << 30) | \
+ CRAMFS_24((((y) & 0x03ffffff) >> 2)) | \
+ (((u32)(((u8*)(x))[8] & 0x3f)) << 24))
+#else
+#error "__BYTE_ORDER must be __LITTLE_ENDIAN or __BIG_ENDIAN"
+#endif
+
/* Uncompression interfaces to the underlying zlib */
-int cramfs_uncompress_block(void *dst, int dstlen, void *src, int srclen);
+int cramfs_uncompress_block(void *dst, void *src, int srclen);
int cramfs_uncompress_init(void);
int cramfs_uncompress_exit(void);
-#endif
+#endif /* __CRAMFS_H */
long zlib_decompress(unsigned char *data_in, unsigned char *cpage_out,
__u32 srclen, __u32 destlen);
+char *mkmodestr(unsigned long mode, char *str);
#endif /* __LINUX_JFFS2_H__ */
#define RSR_ALLBITS (RSR_JTRS|RSR_DBSRS|RSR_DBHRS|RSR_CSRS|RSR_SWRS|RSR_LLRS|RSR_ESRS|RSR_EHRS)
+/*-----------------------------------------------------------------------
+ * Newer chips (MPC866 family and MPC87x/88x family) have different
+ * clock distribution system. Their IMMR lower half is >= 0x0800
+ */
+#define MPC8xx_NEW_CLK 0x0800
+
/*-----------------------------------------------------------------------
* PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
*/
-#ifdef CONFIG_MPC866_et_al
-#define PLPRCR_MF_MSK 0xFFFF001E /* Multiplication factor + PDF bits */
+/* Newer chips (MPC866/87x/88x et al) defines */
#define PLPRCR_MFN_MSK 0xF8000000 /* Multiplication factor numerator bits */
#define PLPRCR_MFN_SHIFT 27 /* Multiplication factor numerator shift*/
#define PLPRCR_MFD_MSK 0x07C00000 /* Multiplication factor denominator bits */
#define PLPRCR_S_SHIFT 20 /* Multiplication factor integer shift */
#define PLPRCR_MFI_MSK 0x000F0000 /* Multiplication factor integer bits */
#define PLPRCR_MFI_SHIFT 16 /* Multiplication factor integer shift */
-#else
+
+#define PLPRCR_PDF_MSK 0x0000001E /* Predivision Factor bits */
+#define PLPRCR_PDF_SHIFT 1 /* Predivision Factor shift value */
+#define PLPRCR_DBRMO 0x00000001 /* DPLL BRM Order bit */
+
+/* Multiplication factor + PDF bits */
+#define PLPRCR_MFACT_MSK (PLPRCR_MFN_MSK | \
+ PLPRCR_MFD_MSK | \
+ PLPRCR_S_MSK | \
+ PLPRCR_MFI_MSK | \
+ PLPRCR_PDF_MSK)
+
+/* Older chips (MPC860/862 et al) defines */
#define PLPRCR_MF_MSK 0xFFF00000 /* Multiplication factor bits */
#define PLPRCR_MF_SHIFT 20 /* Multiplication factor shift value */
-#endif
+
#define PLPRCR_SPLSS 0x00008000 /* SPLL Lock Status Sticky bit */
-#define PLPRCR_TEXPS 0x00004000 /* TEXP Status */
-#ifndef CONFIG_MPC866_et_al
#define PLPRCR_TMIST 0x00001000 /* Timers Interrupt Status */
-#endif
-#define PLPRCR_CSRC 0x00000400 /* Clock Source */
-#ifndef CONFIG_MPC866_et_al
+
#define PLPRCR_LPM_MSK 0x00000300 /* Low Power Mode mask */
#define PLPRCR_LPM_NORMAL 0x00000000 /* normal power management mode */
#define PLPRCR_LPM_DOZE 0x00000100 /* doze power management mode */
#define PLPRCR_LPM_SLEEP 0x00000200 /* sleep power management mode */
#define PLPRCR_LPM_DEEP_SLEEP 0x00000300 /* deep sleep power mgt mode */
#define PLPRCR_LPM_DOWN 0x00000300 /* down power management mode */
-#endif
+
+/* Common defines */
+#define PLPRCR_TEXPS 0x00004000 /* TEXP Status */
+#define PLPRCR_CSRC 0x00000400 /* Clock Source */
+
#define PLPRCR_CSR 0x00000080 /* CheskStop Reset value */
#define PLPRCR_LOLRE 0x00000040 /* Loss Of Lock Reset Enable */
#define PLPRCR_FIOPD 0x00000020 /* Force I/O Pull Down */
-#ifdef CONFIG_MPC866_et_al
-#define PLPRCR_PDF_MSK 0x0000001E /* Predivision Factor bits */
-#define PLPRCR_PDF_SHIFT 1 /* Predivision Factor shift value */
-#define PLPRCR_DBRMO 0x00000001 /* DPLL BRM Order bit */
-#endif
/*-----------------------------------------------------------------------
* SCCR - System Clock and reset Control Register 15-27
#define NIOS_SPI_IE (1 << 8) /* exception int ena */
#define NIOS_SPI_SSO (1 << 10) /* override SS_n output */
+/*------------------------------------------------------------------------
+ * ASMI
+ *----------------------------------------------------------------------*/
+typedef volatile struct nios_asmi_t {
+ unsigned rxdata; /* Rx data reg */
+ unsigned txdata; /* Tx data reg */
+ unsigned status; /* Status reg */
+ unsigned control; /* Control reg */
+ unsigned reserved;
+ unsigned slavesel; /* Slave select */
+ unsigned endofpacket; /* End-of-packet reg */
+}nios_asmi_t;
+
+/* status register */
+#define NIOS_ASMI_ROE (1 << 3) /* rx overrun */
+#define NIOS_ASMI_TOE (1 << 4) /* tx overrun */
+#define NIOS_ASMI_TMT (1 << 5) /* tx empty */
+#define NIOS_ASMI_TRDY (1 << 6) /* tx ready */
+#define NIOS_ASMI_RRDY (1 << 7) /* rx ready */
+#define NIOS_ASMI_E (1 << 8) /* exception */
+#define NIOS_ASMI_EOP (1 << 9) /* eop detected */
+
+/* control register */
+#define NIOS_ASMI_IROE (1 << 3) /* rx overrun int ena */
+#define NIOS_ASMI_ITOE (1 << 4) /* tx overrun int ena */
+#define NIOS_ASMI_ITRDY (1 << 6) /* tx ready int ena */
+#define NIOS_ASMI_IRRDY (1 << 7) /* rx ready int ena */
+#define NIOS_ASMI_IE (1 << 8) /* exception int ena */
+#define NIOS_ASMI_IEOP (1 << 9) /* rx eop int ena */
+#define NIOS_ASMI_SSO (1 << 10) /* slave select enable */
+
#endif /* __NIOSIO_H__ */
/* The RPX series use SLOT_B */
#if defined(CONFIG_RPXCLASSIC) || defined(CONFIG_RPXLITE)
# define CONFIG_PCMCIA_SLOT_B
-#elif defined(CONFIG_ADS) /* The ADS board use SLOT_A */
+#elif defined(CONFIG_ADS) /* The ADS board uses SLOT_A */
# define CONFIG_PCMCIA_SLOT_A
#elif defined(CONFIG_FADS) /* The FADS series are a mess */
-# if defined(CONFIG_MPC86x || defined(CONFIG_MPC821)
+# if defined(CONFIG_MPC86x) || defined(CONFIG_MPC821)
# define CONFIG_PCMCIA_SLOT_A
# else
# define CONFIG_PCMCIA_SLOT_B
projects / karo-tx-uboot.git / commitdiff