#include <asm/arch/cpu.h>
#include <asm/arch/omap3.h>
-/* =============================================================================
- * This section holds the common definitions that correspond to the
- * current default configuration - omap3_evm_config
- * =============================================================================
- */
-
/* ----------------------------------------------------------------------------
* Supported U-boot commands
* ----------------------------------------------------------------------------
*/
-
-/* Default commands to include */
#include <config_cmd_default.h>
-#define CONFIG_CMD_EXT2 /* EXT2 Support */
-#define CONFIG_CMD_FAT /* FAT support */
-#define CONFIG_CMD_JFFS2 /* JFFS2 Support */
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_I2C /* I2C serial bus support */
-#define CONFIG_CMD_MMC /* MMC support */
-#define CONFIG_CMD_NAND /* NAND support */
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_NAND
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_PING
/* #define CONFIG_MUSB_UDC */
/* -----------------------------------------------------------------------------
- * Default environment
+ * Include common board configuration
* -----------------------------------------------------------------------------
*/
-#define CONFIG_BOOTDELAY 10
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "loadaddr=0x82000000\0" \
- "usbtty=cdc_acm\0" \
- "mmcdev=0\0" \
- "memsize=128M\0" \
- "console=ttyO0,115200n8\0" \
- "mmcargs=setenv bootargs console=${console} " \
- "mem=${memsize}\0 " \
- "root=/dev/mmcblk0p2 rw " \
- "rootfstype=ext3 rootwait\0" \
- "nandargs=setenv bootargs console=${console} " \
- "mem=${memsize}\0 " \
- "root=/dev/mtdblock4 rw " \
- "rootfstype=jffs2\0" \
- "loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \
- "bootscript=echo Running bootscript from mmc ...; " \
- "source ${loadaddr}\0" \
- "loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \
- "mmcboot=echo Booting from mmc ...; " \
- "run mmcargs; " \
- "bootm ${loadaddr}\0" \
- "nandboot=echo Booting from nand ...; " \
- "run nandargs; " \
- "onenand read ${loadaddr} 280000 400000; " \
- "bootm ${loadaddr}\0" \
-
-#define CONFIG_BOOTCOMMAND \
- "if mmc rescan ${mmcdev}; then " \
- "if run loadbootscript; then " \
- "run bootscript; " \
- "else " \
- "if run loaduimage; then " \
- "run mmcboot; " \
- "else run nandboot; " \
- "fi; " \
- "fi; " \
- "else run nandboot; fi"
-
-/* =============================================================================
- * This section holds the common definitions that can be used by
- * all OMAP3EVM based configurations.
- * =============================================================================
- */
-
-/*
- * High level configuration options
- */
-#define CONFIG_OMAP /* This is TI OMAP core */
-#define CONFIG_OMAP34XX /* belonging to 34XX family */
-#define CONFIG_OMAP3430 /* which is in a 3430 */
-
-#define CONFIG_SDRC /* The chip has SDRC controller */
-
-#define CONFIG_OMAP3_EVM /* This is a OMAP3 EVM */
-#define CONFIG_OMAP3_MICRON_DDR /* with MICRON DDR part */
-#define CONFIG_TWL4030_POWER /* with TWL4030 PMIC */
-
-#undef CONFIG_USE_IRQ /* no support for IRQs */
-
-/*
- * Clock related definitions
- */
-#define V_OSCK 26000000 /* Clock output from T2 */
-#define V_SCLK (V_OSCK >> 1)
-
-/*
- * OMAP3 has 12 GP timers, they can be driven by the system clock
- * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
- * This rate is divided by a local divisor.
- */
-#define CONFIG_SYS_TIMERBASE OMAP34XX_GPT2
-#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
-#define CONFIG_SYS_HZ 1000
-
-/* Size of environment - 128KB */
-#define CONFIG_ENV_SIZE (128 << 10)
-
-/* Size of malloc pool */
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10))
-
-/*
- * Stack sizes
- * These values are used in start.S
- */
-#define CONFIG_STACKSIZE (128 << 10) /* regular stack 128 KiB */
-
-#ifdef CONFIG_USE_IRQ
-#define CONFIG_STACKSIZE_IRQ (4 << 10) /* IRQ stack 4 KiB */
-#define CONFIG_STACKSIZE_FIQ (4 << 10) /* FIQ stack 4 KiB */
-#endif
-
-/*
- * Physical Memory Map
- * Note 1: CS1 may or may not be populated
- * Note 2: SDRAM size is expected to be at least 32MB
- */
-#define CONFIG_NR_DRAM_BANKS 2
-#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
-#define PHYS_SDRAM_1_SIZE (32 << 20)
-#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
-
-/* SDRAM Bank Allocation method */
-#define SDRC_R_B_C
-
-/* Limits for memtest */
-#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0)
-#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \
- 0x01F00000) /* 31MB */
-
-/* Default load address */
-#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0)
-
-/* -----------------------------------------------------------------------------
- * Hardware drivers
- * -----------------------------------------------------------------------------
- */
-
-/*
- * NS16550 Configuration
- */
-#define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */
-
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE (-4)
-#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK
-
-/*
- * select serial console configuration
- */
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_SERIAL1 1 /* UART1 on OMAP3 EVM */
-#define CONFIG_SYS_NS16550_COM1 OMAP34XX_UART1
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\
- 115200}
-
-/*
- * I2C
- */
-#define CONFIG_HARD_I2C
-#define CONFIG_DRIVER_OMAP34XX_I2C
-
-#define CONFIG_SYS_I2C_SPEED 100000
-#define CONFIG_SYS_I2C_SLAVE 1
-#define CONFIG_SYS_I2C_BUS 0
-#define CONFIG_SYS_I2C_BUS_SELECT 1
-
-/*
- * PISMO support
- */
-#define PISMO1_NAND_SIZE GPMC_SIZE_128M
-#define PISMO1_ONEN_SIZE GPMC_SIZE_128M
-
-/* Monitor at start of flash - Reserve 2 sectors */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-
-#define CONFIG_SYS_MONITOR_LEN (256 << 10)
-
-/* Start location & size of environment */
-#define ONENAND_ENV_OFFSET 0x260000
-#define SMNAND_ENV_OFFSET 0x260000
-
-#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
-
-/*
- * NAND
- */
-/* Physical address to access NAND */
-#define CONFIG_SYS_NAND_ADDR NAND_BASE
-
-/* Physical address to access NAND at CS0 */
-#define CONFIG_SYS_NAND_BASE NAND_BASE
-
-/* Max number of NAND devices */
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-
-/* Timeout values (in ticks) */
-#define CONFIG_SYS_FLASH_ERASE_TOUT (100 * CONFIG_SYS_HZ)
-#define CONFIG_SYS_FLASH_WRITE_TOUT (100 * CONFIG_SYS_HZ)
-
-/* Flash banks JFFS2 should use */
-#define CONFIG_SYS_MAX_MTD_BANKS (CONFIG_SYS_MAX_FLASH_BANKS + \
- CONFIG_SYS_MAX_NAND_DEVICE)
-
-#define CONFIG_SYS_JFFS2_MEM_NAND
-#define CONFIG_SYS_JFFS2_FIRST_BANK CONFIG_SYS_MAX_FLASH_BANKS
-#define CONFIG_SYS_JFFS2_NUM_BANKS 1
-
-#define CONFIG_JFFS2_NAND
-/* nand device jffs2 lives on */
-#define CONFIG_JFFS2_DEV "nand0"
-/* Start of jffs2 partition */
-#define CONFIG_JFFS2_PART_OFFSET 0x680000
-/* Size of jffs2 partition */
-#define CONFIG_JFFS2_PART_SIZE 0xf980000
-
-/*
- * USB
- */
-#ifdef CONFIG_USB_OMAP3
-
-#ifdef CONFIG_MUSB_HCD
-#define CONFIG_CMD_USB
-
-#define CONFIG_USB_STORAGE
-#define CONGIG_CMD_STORAGE
-#define CONFIG_CMD_FAT
-
-#ifdef CONFIG_USB_KEYBOARD
-#define CONFIG_SYS_USB_EVENT_POLL
-#define CONFIG_PREBOOT "usb start"
-#endif /* CONFIG_USB_KEYBOARD */
-
-#endif /* CONFIG_MUSB_HCD */
-
-#ifdef CONFIG_MUSB_UDC
-/* USB device configuration */
-#define CONFIG_USB_DEVICE
-#define CONFIG_USB_TTY
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV
-
-/* Change these to suit your needs */
-#define CONFIG_USBD_VENDORID 0x0451
-#define CONFIG_USBD_PRODUCTID 0x5678
-#define CONFIG_USBD_MANUFACTURER "Texas Instruments"
-#define CONFIG_USBD_PRODUCT_NAME "EVM"
-#endif /* CONFIG_MUSB_UDC */
-
-#endif /* CONFIG_USB_OMAP3 */
-
-/* ----------------------------------------------------------------------------
- * U-boot features
- * ----------------------------------------------------------------------------
- */
-#define CONFIG_SYS_PROMPT "OMAP3_EVM # "
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-#define CONFIG_SYS_MAXARGS 16 /* max args for a command */
-
-#define CONFIG_MISC_INIT_R
-
-#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-#define CONFIG_REVISION_TAG
-
-/* Size of Console IO buffer */
-#define CONFIG_SYS_CBSIZE 512
-
-/* Size of print buffer */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
- sizeof(CONFIG_SYS_PROMPT) + 16)
-
-/* Size of bootarg buffer */
-#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE)
-
-#define CONFIG_BOOTFILE uImage
-
-/*
- * NAND / OneNAND
- */
-#if defined(CONFIG_CMD_NAND)
-#define CONFIG_SYS_FLASH_BASE PISMO1_NAND_BASE
-
-#define CONFIG_NAND_OMAP_GPMC
-#define GPMC_NAND_ECC_LP_x16_LAYOUT
-#define CONFIG_ENV_IS_IN_NAND
-#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
-#elif defined(CONFIG_CMD_ONENAND)
-#define CONFIG_SYS_FLASH_BASE PISMO1_ONEN_BASE
-#define CONFIG_SYS_ONENAND_BASE ONENAND_MAP
-
-#define CONFIG_ENV_IS_IN_ONENAND
-#define CONFIG_ENV_OFFSET ONENAND_ENV_OFFSET
-#endif
-
-#define CONFIG_ENV_ADDR CONFIG_ENV_OFFSET
-
-#if defined(CONFIG_CMD_NET)
-
-/* Ethernet (SMSC9115 from SMSC9118 family) */
-#define CONFIG_SMC911X
-#define CONFIG_SMC911X_32_BIT
-#define CONFIG_SMC911X_BASE 0x2C000000
-
-/* BOOTP fields */
-#define CONFIG_BOOTP_SUBNETMASK 0x00000001
-#define CONFIG_BOOTP_GATEWAY 0x00000002
-#define CONFIG_BOOTP_HOSTNAME 0x00000004
-#define CONFIG_BOOTP_BOOTPATH 0x00000010
-
-#endif /* CONFIG_CMD_NET */
-
-/* Support for relocation */
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
-#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
-#define CONFIG_SYS_INIT_RAM_SIZE 0x800
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
- CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-
-/* -----------------------------------------------------------------------------
- * Board specific
- * -----------------------------------------------------------------------------
- */
-#define CONFIG_SYS_NO_FLASH
-
-/* Uncomment to define the board revision statically */
-/* #define CONFIG_STATIC_BOARD_REV OMAP3EVM_BOARD_GEN_2 */
+#include "omap3_evm_common.h"
/* -----------------------------------------------------------------------------
* Default environment
* -----------------------------------------------------------------------------
*/
#define CONFIG_BOOTDELAY 10
-#define CONFIG_BOOTFILE "uImage"
#define CONFIG_EXTRA_ENV_SETTINGS \
"loadaddr=0x82000000\0" \
--- /dev/null
+/*
+ * Common configuration settings for the TI OMAP3 EVM board.
+ *
+ * Copyright (C) 2006-2011 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __OMAP3_EVM_COMMON_H
+#define __OMAP3_EVM_COMMON_H
+
+/*
+ * High level configuration options
+ */
+#define CONFIG_OMAP /* This is TI OMAP core */
+#define CONFIG_OMAP34XX /* belonging to 34XX family */
+#define CONFIG_OMAP3430 /* which is in a 3430 */
+
+#define CONFIG_SDRC /* The chip has SDRC controller */
+
+#define CONFIG_OMAP3_EVM /* This is a OMAP3 EVM */
+#define CONFIG_OMAP3_MICRON_DDR /* with MICRON DDR part */
+#define CONFIG_TWL4030_POWER /* with TWL4030 PMIC */
+
+#undef CONFIG_USE_IRQ /* no support for IRQs */
+
+/*
+ * Clock related definitions
+ */
+#define V_OSCK 26000000 /* Clock output from T2 */
+#define V_SCLK (V_OSCK >> 1)
+
+/*
+ * OMAP3 has 12 GP timers, they can be driven by the system clock
+ * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
+ * This rate is divided by a local divisor.
+ */
+#define CONFIG_SYS_TIMERBASE OMAP34XX_GPT2
+#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
+#define CONFIG_SYS_HZ 1000
+
+/* Size of environment - 128KB */
+#define CONFIG_ENV_SIZE (128 << 10)
+
+/* Size of malloc pool */
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10))
+
+/*
+ * Stack sizes
+ * These values are used in start.S
+ */
+#define CONFIG_STACKSIZE (128 << 10) /* regular stack 128 KiB */
+
+#ifdef CONFIG_USE_IRQ
+#define CONFIG_STACKSIZE_IRQ (4 << 10) /* IRQ stack 4 KiB */
+#define CONFIG_STACKSIZE_FIQ (4 << 10) /* FIQ stack 4 KiB */
+#endif
+
+/*
+ * Physical Memory Map
+ * Note 1: CS1 may or may not be populated
+ * Note 2: SDRAM size is expected to be at least 32MB
+ */
+#define CONFIG_NR_DRAM_BANKS 2
+#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
+#define PHYS_SDRAM_1_SIZE (32 << 20)
+#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
+
+/* SDRAM Bank Allocation method */
+#define SDRC_R_B_C
+
+/* Limits for memtest */
+#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0)
+#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \
+ 0x01F00000) /* 31MB */
+
+/* Default load address */
+#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0)
+
+/* -----------------------------------------------------------------------------
+ * Hardware drivers
+ * -----------------------------------------------------------------------------
+ */
+
+/*
+ * NS16550 Configuration
+ */
+#define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */
+
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE (-4)
+#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK
+
+/*
+ * select serial console configuration
+ */
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_SERIAL1 1 /* UART1 on OMAP3 EVM */
+#define CONFIG_SYS_NS16550_COM1 OMAP34XX_UART1
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\
+ 115200}
+
+/*
+ * I2C
+ */
+#define CONFIG_HARD_I2C
+#define CONFIG_DRIVER_OMAP34XX_I2C
+
+#define CONFIG_SYS_I2C_SPEED 100000
+#define CONFIG_SYS_I2C_SLAVE 1
+#define CONFIG_SYS_I2C_BUS 0
+#define CONFIG_SYS_I2C_BUS_SELECT 1
+
+/*
+ * PISMO support
+ */
+#define PISMO1_NAND_SIZE GPMC_SIZE_128M
+#define PISMO1_ONEN_SIZE GPMC_SIZE_128M
+
+/* Monitor at start of flash - Reserve 2 sectors */
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
+
+#define CONFIG_SYS_MONITOR_LEN (256 << 10)
+
+/* Start location & size of environment */
+#define ONENAND_ENV_OFFSET 0x260000
+#define SMNAND_ENV_OFFSET 0x260000
+
+#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
+
+/*
+ * NAND
+ */
+/* Physical address to access NAND */
+#define CONFIG_SYS_NAND_ADDR NAND_BASE
+
+/* Physical address to access NAND at CS0 */
+#define CONFIG_SYS_NAND_BASE NAND_BASE
+
+/* Max number of NAND devices */
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+
+/* Timeout values (in ticks) */
+#define CONFIG_SYS_FLASH_ERASE_TOUT (100 * CONFIG_SYS_HZ)
+#define CONFIG_SYS_FLASH_WRITE_TOUT (100 * CONFIG_SYS_HZ)
+
+/* Flash banks JFFS2 should use */
+#define CONFIG_SYS_MAX_MTD_BANKS (CONFIG_SYS_MAX_FLASH_BANKS + \
+ CONFIG_SYS_MAX_NAND_DEVICE)
+
+#define CONFIG_SYS_JFFS2_MEM_NAND
+#define CONFIG_SYS_JFFS2_FIRST_BANK CONFIG_SYS_MAX_FLASH_BANKS
+#define CONFIG_SYS_JFFS2_NUM_BANKS 1
+
+#define CONFIG_JFFS2_NAND
+/* nand device jffs2 lives on */
+#define CONFIG_JFFS2_DEV "nand0"
+/* Start of jffs2 partition */
+#define CONFIG_JFFS2_PART_OFFSET 0x680000
+/* Size of jffs2 partition */
+#define CONFIG_JFFS2_PART_SIZE 0xf980000
+
+/*
+ * USB
+ */
+#ifdef CONFIG_USB_OMAP3
+
+#ifdef CONFIG_MUSB_HCD
+#define CONFIG_CMD_USB
+
+#define CONFIG_USB_STORAGE
+#define CONGIG_CMD_STORAGE
+#define CONFIG_CMD_FAT
+
+#ifdef CONFIG_USB_KEYBOARD
+#define CONFIG_SYS_USB_EVENT_POLL
+#define CONFIG_PREBOOT "usb start"
+#endif /* CONFIG_USB_KEYBOARD */
+
+#endif /* CONFIG_MUSB_HCD */
+
+#ifdef CONFIG_MUSB_UDC
+/* USB device configuration */
+#define CONFIG_USB_DEVICE
+#define CONFIG_USB_TTY
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+
+/* Change these to suit your needs */
+#define CONFIG_USBD_VENDORID 0x0451
+#define CONFIG_USBD_PRODUCTID 0x5678
+#define CONFIG_USBD_MANUFACTURER "Texas Instruments"
+#define CONFIG_USBD_PRODUCT_NAME "EVM"
+#endif /* CONFIG_MUSB_UDC */
+
+#endif /* CONFIG_USB_OMAP3 */
+
+/* ----------------------------------------------------------------------------
+ * U-boot features
+ * ----------------------------------------------------------------------------
+ */
+#define CONFIG_SYS_PROMPT "OMAP3_EVM # "
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_MAXARGS 16 /* max args for a command */
+
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+#define CONFIG_REVISION_TAG
+
+/* Size of Console IO buffer */
+#define CONFIG_SYS_CBSIZE 512
+
+/* Size of print buffer */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
+ sizeof(CONFIG_SYS_PROMPT) + 16)
+
+/* Size of bootarg buffer */
+#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE)
+
+#define CONFIG_BOOTFILE "uImage"
+
+/*
+ * NAND / OneNAND
+ */
+#if defined(CONFIG_CMD_NAND)
+#define CONFIG_SYS_FLASH_BASE PISMO1_NAND_BASE
+
+#define CONFIG_NAND_OMAP_GPMC
+#define GPMC_NAND_ECC_LP_x16_LAYOUT
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
+#elif defined(CONFIG_CMD_ONENAND)
+#define CONFIG_SYS_FLASH_BASE PISMO1_ONEN_BASE
+#define CONFIG_SYS_ONENAND_BASE ONENAND_MAP
+
+#define CONFIG_ENV_IS_IN_ONENAND
+#define CONFIG_ENV_OFFSET ONENAND_ENV_OFFSET
+#endif
+
+#define CONFIG_ENV_ADDR CONFIG_ENV_OFFSET
+
+#if defined(CONFIG_CMD_NET)
+
+/* Ethernet (SMSC9115 from SMSC9118 family) */
+#define CONFIG_NET_MULTI
+#define CONFIG_SMC911X
+#define CONFIG_SMC911X_32_BIT
+#define CONFIG_SMC911X_BASE 0x2C000000
+
+/* BOOTP fields */
+#define CONFIG_BOOTP_SUBNETMASK 0x00000001
+#define CONFIG_BOOTP_GATEWAY 0x00000002
+#define CONFIG_BOOTP_HOSTNAME 0x00000004
+#define CONFIG_BOOTP_BOOTPATH 0x00000010
+
+#endif /* CONFIG_CMD_NET */
+
+/* Support for relocation */
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
+#define CONFIG_SYS_INIT_RAM_SIZE 0x800
+#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
+ CONFIG_SYS_INIT_RAM_SIZE - \
+ GENERATED_GBL_DATA_SIZE)
+
+/* -----------------------------------------------------------------------------
+ * Board specific
+ * -----------------------------------------------------------------------------
+ */
+#define CONFIG_SYS_NO_FLASH
+
+/* Uncomment to define the board revision statically */
+/* #define CONFIG_STATIC_BOARD_REV OMAP3EVM_BOARD_GEN_2 */
+
+#endif /* __OMAP3_EVM_COMMON_H */
projects / karo-tx-uboot.git / commitdiff