+/*
+ * Copyright (c) 2013 Samsung Electronics Co., Ltd. All rights reserved.
+ * Sanghee Kim <sh0130.kim@samsung.com>
+ * Piotr Wilczek <p.wilczek@samsung.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <lcd.h>
+#include <asm/io.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/mmc.h>
+#include <asm/arch/power.h>
+#include <asm/arch/clk.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/mipi_dsim.h>
+#include <asm/arch/pinmux.h>
+#include <asm/arch/power.h>
+#include <power/pmic.h>
+#include <power/max77686_pmic.h>
+#include <power/battery.h>
+#include <power/max77693_pmic.h>
+#include <power/max77693_muic.h>
+#include <power/max77693_fg.h>
+#include <libtizen.h>
+#include <errno.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static struct exynos4x12_gpio_part1 *gpio1;
+static struct exynos4x12_gpio_part2 *gpio2;
+
+static unsigned int board_rev = -1;
+
+static inline u32 get_model_rev(void);
+
+static void check_hw_revision(void)
+{
+ int modelrev = 0;
+ int i;
+
+ gpio2 = (struct exynos4x12_gpio_part2 *)EXYNOS4X12_GPIO_PART2_BASE;
+
+ /*
+ * GPM1[1:0]: MODEL_REV[1:0]
+ * Don't set as pull-none for these N/C pin.
+ * TRM say that it may cause unexcepted state and leakage current.
+ * and pull-none is only for output function.
+ */
+ for (i = 0; i < 2; i++)
+ s5p_gpio_cfg_pin(&gpio2->m1, i, GPIO_INPUT);
+
+ /* GPM1[5:2]: HW_REV[3:0] */
+ for (i = 2; i < 6; i++) {
+ s5p_gpio_cfg_pin(&gpio2->m1, i, GPIO_INPUT);
+ s5p_gpio_set_pull(&gpio2->m1, i, GPIO_PULL_NONE);
+ }
+
+ /* GPM1[1:0]: MODEL_REV[1:0] */
+ for (i = 0; i < 2; i++)
+ modelrev |= (s5p_gpio_get_value(&gpio2->m1, i) << i);
+
+ /* board_rev[15:8] = model */
+ board_rev = modelrev << 8;
+}
+
+#ifdef CONFIG_DISPLAY_BOARDINFO
+int checkboard(void)
+{
+ puts("Board:\tTRATS2\n");
+ return 0;
+}
+#endif
+
+static void show_hw_revision(void)
+{
+ printf("HW Revision:\t0x%04x\n", board_rev);
+}
+
+u32 get_board_rev(void)
+{
+ return board_rev;
+}
+
+static inline u32 get_model_rev(void)
+{
+ return (board_rev >> 8) & 0xff;
+}
+
+static void board_external_gpio_init(void)
+{
+ gpio2 = (struct exynos4x12_gpio_part2 *)EXYNOS4X12_GPIO_PART2_BASE;
+
+ /*
+ * some pins which in alive block are connected with external pull-up
+ * but it's default setting is pull-down.
+ * if that pin set as input then that floated
+ */
+
+ s5p_gpio_set_pull(&gpio2->x0, 2, GPIO_PULL_NONE); /* PS_ALS_INT */
+ s5p_gpio_set_pull(&gpio2->x0, 4, GPIO_PULL_NONE); /* TSP_nINT */
+ s5p_gpio_set_pull(&gpio2->x0, 7, GPIO_PULL_NONE); /* AP_PMIC_IRQ*/
+ s5p_gpio_set_pull(&gpio2->x1, 5, GPIO_PULL_NONE); /* IF_PMIC_IRQ*/
+ s5p_gpio_set_pull(&gpio2->x2, 0, GPIO_PULL_NONE); /* VOL_UP */
+ s5p_gpio_set_pull(&gpio2->x2, 1, GPIO_PULL_NONE); /* VOL_DOWN */
+ s5p_gpio_set_pull(&gpio2->x2, 3, GPIO_PULL_NONE); /* FUEL_ALERT */
+ s5p_gpio_set_pull(&gpio2->x2, 4, GPIO_PULL_NONE); /* ADC_INT */
+ s5p_gpio_set_pull(&gpio2->x2, 7, GPIO_PULL_NONE); /* nPOWER */
+ s5p_gpio_set_pull(&gpio2->x3, 0, GPIO_PULL_NONE); /* WPC_INT */
+ s5p_gpio_set_pull(&gpio2->x3, 5, GPIO_PULL_NONE); /* OK_KEY */
+ s5p_gpio_set_pull(&gpio2->x3, 7, GPIO_PULL_NONE); /* HDMI_HPD */
+}
+
+#ifdef CONFIG_SYS_I2C_INIT_BOARD
+static void board_init_i2c(void)
+{
+ gpio1 = (struct exynos4x12_gpio_part1 *)EXYNOS4X12_GPIO_PART1_BASE;
+ gpio2 = (struct exynos4x12_gpio_part2 *)EXYNOS4X12_GPIO_PART2_BASE;
+
+ /* I2C_7 */
+ s5p_gpio_direction_output(&gpio1->d0, 2, 1);
+ s5p_gpio_direction_output(&gpio1->d0, 3, 1);
+
+ /* I2C_8 */
+ s5p_gpio_direction_output(&gpio1->f1, 4, 1);
+ s5p_gpio_direction_output(&gpio1->f1, 5, 1);
+
+ /* I2C_9 */
+ s5p_gpio_direction_output(&gpio2->m2, 1, 1);
+ s5p_gpio_direction_output(&gpio2->m2, 0, 1);
+}
+#endif
+
+int board_early_init_f(void)
+{
+ check_hw_revision();
+ board_external_gpio_init();
+
+ gd->flags |= GD_FLG_DISABLE_CONSOLE;
+
+ return 0;
+}
+
+static int pmic_init_max77686(void);
+
+int board_init(void)
+{
+ struct exynos4_power *pwr =
+ (struct exynos4_power *)EXYNOS4X12_POWER_BASE;
+
+ gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
+
+ /* workaround: clear INFORM4..5 */
+ writel(0, (unsigned int)&pwr->inform4);
+ writel(0, (unsigned int)&pwr->inform5);
+
+ return 0;
+}
+
+int power_init_board(void)
+{
+ int chrg;
+ struct power_battery *pb;
+ struct pmic *p_chrg, *p_muic, *p_fg, *p_bat;
+
+#ifdef CONFIG_SYS_I2C_INIT_BOARD
+ board_init_i2c();
+#endif
+ pmic_init(I2C_0); /* I2C adapter 0 - bus name I2C_5 */
+ pmic_init_max77686();
+ pmic_init_max77693(I2C_2); /* I2C adapter 2 - bus name I2C_10 */
+ power_muic_init(I2C_2); /* I2C adapter 2 - bus name I2C_10 */
+ power_fg_init(I2C_1); /* I2C adapter 1 - bus name I2C_9 */
+ power_bat_init(0);
+
+ p_chrg = pmic_get("MAX77693_PMIC");
+ if (!p_chrg) {
+ puts("MAX77693_PMIC: Not found\n");
+ return -ENODEV;
+ }
+
+ p_muic = pmic_get("MAX77693_MUIC");
+ if (!p_muic) {
+ puts("MAX77693_MUIC: Not found\n");
+ return -ENODEV;
+ }
+
+ p_fg = pmic_get("MAX77693_FG");
+ if (!p_fg) {
+ puts("MAX17042_FG: Not found\n");
+ return -ENODEV;
+ }
+
+ if (p_chrg->chrg->chrg_bat_present(p_chrg) == 0)
+ puts("No battery detected\n");
+
+ p_bat = pmic_get("BAT_TRATS2");
+ if (!p_bat) {
+ puts("BAT_TRATS2: Not found\n");
+ return -ENODEV;
+ }
+
+ p_fg->parent = p_bat;
+ p_chrg->parent = p_bat;
+ p_muic->parent = p_bat;
+
+ p_bat->pbat->battery_init(p_bat, p_fg, p_chrg, p_muic);
+
+ pb = p_bat->pbat;
+ chrg = p_muic->chrg->chrg_type(p_muic);
+ debug("CHARGER TYPE: %d\n", chrg);
+
+ if (!p_chrg->chrg->chrg_bat_present(p_chrg)) {
+ puts("No battery detected\n");
+ return -1;
+ }
+
+ p_fg->fg->fg_battery_check(p_fg, p_bat);
+
+ if (pb->bat->state == CHARGE && chrg == CHARGER_USB)
+ puts("CHARGE Battery !\n");
+
+ return 0;
+}
+
+int dram_init(void)
+{
+ u32 size_mb;
+
+ size_mb = (get_ram_size((long *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE) +
+ get_ram_size((long *)PHYS_SDRAM_2, PHYS_SDRAM_2_SIZE) +
+ get_ram_size((long *)PHYS_SDRAM_3, PHYS_SDRAM_3_SIZE) +
+ get_ram_size((long *)PHYS_SDRAM_4, PHYS_SDRAM_4_SIZE)) >> 20;
+
+ gd->ram_size = size_mb << 20;
+
+ return 0;
+}
+
+void dram_init_banksize(void)
+{
+ gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+ gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
+ gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
+ gd->bd->bi_dram[1].size = PHYS_SDRAM_2_SIZE;
+ gd->bd->bi_dram[2].start = PHYS_SDRAM_3;
+ gd->bd->bi_dram[2].size = PHYS_SDRAM_3_SIZE;
+ gd->bd->bi_dram[3].start = PHYS_SDRAM_4;
+ gd->bd->bi_dram[3].size = PHYS_SDRAM_4_SIZE;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+ int err0, err2 = 0;
+
+ gpio2 = (struct exynos4x12_gpio_part2 *)EXYNOS4X12_GPIO_PART2_BASE;
+
+ /* eMMC_EN: SD_0_CDn: GPK0[2] Output High */
+ s5p_gpio_direction_output(&gpio2->k0, 2, 1);
+ s5p_gpio_set_pull(&gpio2->k0, 2, GPIO_PULL_NONE);
+
+ /*
+ * eMMC GPIO:
+ * SDR 8-bit@48MHz at MMC0
+ * GPK0[0] SD_0_CLK(2)
+ * GPK0[1] SD_0_CMD(2)
+ * GPK0[2] SD_0_CDn -> Not used
+ * GPK0[3:6] SD_0_DATA[0:3](2)
+ * GPK1[3:6] SD_0_DATA[0:3](3)
+ *
+ * DDR 4-bit@26MHz at MMC4
+ * GPK0[0] SD_4_CLK(3)
+ * GPK0[1] SD_4_CMD(3)
+ * GPK0[2] SD_4_CDn -> Not used
+ * GPK0[3:6] SD_4_DATA[0:3](3)
+ * GPK1[3:6] SD_4_DATA[4:7](4)
+ */
+
+ err0 = exynos_pinmux_config(PERIPH_ID_SDMMC0, PINMUX_FLAG_8BIT_MODE);
+
+ /*
+ * MMC device init
+ * mmc0 : eMMC (8-bit buswidth)
+ * mmc2 : SD card (4-bit buswidth)
+ */
+ if (err0)
+ debug("SDMMC0 not configured\n");
+ else
+ err0 = s5p_mmc_init(0, 8);
+
+ /* T-flash detect */
+ s5p_gpio_cfg_pin(&gpio2->x3, 4, 0xf);
+ s5p_gpio_set_pull(&gpio2->x3, 4, GPIO_PULL_UP);
+
+ /*
+ * Check the T-flash detect pin
+ * GPX3[4] T-flash detect pin
+ */
+ if (!s5p_gpio_get_value(&gpio2->x3, 4)) {
+ err2 = exynos_pinmux_config(PERIPH_ID_SDMMC2, PINMUX_FLAG_NONE);
+ if (err2)
+ debug("SDMMC2 not configured\n");
+ else
+ err2 = s5p_mmc_init(2, 4);
+ }
+
+ return err0 & err2;
+}
+
+static int pmic_init_max77686(void)
+{
+ struct pmic *p = pmic_get("MAX77686_PMIC");
+
+ if (pmic_probe(p))
+ return -1;
+
+ /* BUCK/LDO Output Voltage */
+ max77686_set_ldo_voltage(p, 21, 2800000); /* LDO21 VTF_2.8V */
+ max77686_set_ldo_voltage(p, 23, 3300000); /* LDO23 TSP_AVDD_3.3V*/
+ max77686_set_ldo_voltage(p, 24, 1800000); /* LDO24 TSP_VDD_1.8V */
+
+ /* BUCK/LDO Output Mode */
+ max77686_set_buck_mode(p, 1, OPMODE_STANDBY); /* BUCK1 VMIF_1.1V_AP */
+ max77686_set_buck_mode(p, 2, OPMODE_ON); /* BUCK2 VARM_1.0V_AP */
+ max77686_set_buck_mode(p, 3, OPMODE_ON); /* BUCK3 VINT_1.0V_AP */
+ max77686_set_buck_mode(p, 4, OPMODE_ON); /* BUCK4 VG3D_1.0V_AP */
+ max77686_set_buck_mode(p, 5, OPMODE_ON); /* BUCK5 VMEM_1.2V_AP */
+ max77686_set_buck_mode(p, 6, OPMODE_ON); /* BUCK6 VCC_SUB_1.35V*/
+ max77686_set_buck_mode(p, 7, OPMODE_ON); /* BUCK7 VCC_SUB_2.0V */
+ max77686_set_buck_mode(p, 8, OPMODE_OFF); /* VMEM_VDDF_2.85V */
+ max77686_set_buck_mode(p, 9, OPMODE_OFF); /* CAM_ISP_CORE_1.2V*/
+
+ max77686_set_ldo_mode(p, 1, OPMODE_LPM); /* LDO1 VALIVE_1.0V_AP*/
+ max77686_set_ldo_mode(p, 2, OPMODE_STANDBY); /* LDO2 VM1M2_1.2V_AP */
+ max77686_set_ldo_mode(p, 3, OPMODE_LPM); /* LDO3 VCC_1.8V_AP */
+ max77686_set_ldo_mode(p, 4, OPMODE_LPM); /* LDO4 VCC_2.8V_AP */
+ max77686_set_ldo_mode(p, 5, OPMODE_OFF); /* LDO5_VCC_1.8V_IO */
+ max77686_set_ldo_mode(p, 6, OPMODE_STANDBY); /* LDO6 VMPLL_1.0V_AP */
+ max77686_set_ldo_mode(p, 7, OPMODE_STANDBY); /* LDO7 VPLL_1.0V_AP */
+ max77686_set_ldo_mode(p, 8, OPMODE_LPM); /* LDO8 VMIPI_1.0V_AP */
+ max77686_set_ldo_mode(p, 9, OPMODE_OFF); /* CAM_ISP_MIPI_1.2*/
+ max77686_set_ldo_mode(p, 10, OPMODE_LPM); /* LDO10 VMIPI_1.8V_AP*/
+ max77686_set_ldo_mode(p, 11, OPMODE_STANDBY); /* LDO11 VABB1_1.8V_AP*/
+ max77686_set_ldo_mode(p, 12, OPMODE_LPM); /* LDO12 VUOTG_3.0V_AP*/
+ max77686_set_ldo_mode(p, 13, OPMODE_OFF); /* LDO13 VC2C_1.8V_AP */
+ max77686_set_ldo_mode(p, 14, OPMODE_STANDBY); /* VABB02_1.8V_AP */
+ max77686_set_ldo_mode(p, 15, OPMODE_STANDBY); /* LDO15 VHSIC_1.0V_AP*/
+ max77686_set_ldo_mode(p, 16, OPMODE_STANDBY); /* LDO16 VHSIC_1.8V_AP*/
+ max77686_set_ldo_mode(p, 17, OPMODE_OFF); /* CAM_SENSOR_CORE_1.2*/
+ max77686_set_ldo_mode(p, 18, OPMODE_OFF); /* CAM_ISP_SEN_IO_1.8V*/
+ max77686_set_ldo_mode(p, 19, OPMODE_OFF); /* LDO19 VT_CAM_1.8V */
+ max77686_set_ldo_mode(p, 20, OPMODE_ON); /* LDO20 VDDQ_PRE_1.8V*/
+ max77686_set_ldo_mode(p, 21, OPMODE_OFF); /* LDO21 VTF_2.8V */
+ max77686_set_ldo_mode(p, 22, OPMODE_OFF); /* LDO22 VMEM_VDD_2.8V*/
+ max77686_set_ldo_mode(p, 23, OPMODE_OFF); /* LDO23 TSP_AVDD_3.3V*/
+ max77686_set_ldo_mode(p, 24, OPMODE_OFF); /* LDO24 TSP_VDD_1.8V */
+ max77686_set_ldo_mode(p, 25, OPMODE_OFF); /* LDO25 VCC_3.3V_LCD */
+ max77686_set_ldo_mode(p, 26, OPMODE_OFF); /*LDO26 VCC_3.0V_MOTOR*/
+
+ return 0;
+}
+
+/*
+ * LCD
+ */
+
+#ifdef CONFIG_LCD
+static struct mipi_dsim_config dsim_config = {
+ .e_interface = DSIM_VIDEO,
+ .e_virtual_ch = DSIM_VIRTUAL_CH_0,
+ .e_pixel_format = DSIM_24BPP_888,
+ .e_burst_mode = DSIM_BURST_SYNC_EVENT,
+ .e_no_data_lane = DSIM_DATA_LANE_4,
+ .e_byte_clk = DSIM_PLL_OUT_DIV8,
+ .hfp = 1,
+
+ .p = 3,
+ .m = 120,
+ .s = 1,
+
+ /* D-PHY PLL stable time spec :min = 200usec ~ max 400usec */
+ .pll_stable_time = 500,
+
+ /* escape clk : 10MHz */
+ .esc_clk = 20 * 1000000,
+
+ /* stop state holding counter after bta change count 0 ~ 0xfff */
+ .stop_holding_cnt = 0x7ff,
+ /* bta timeout 0 ~ 0xff */
+ .bta_timeout = 0xff,
+ /* lp rx timeout 0 ~ 0xffff */
+ .rx_timeout = 0xffff,
+};
+
+static struct exynos_platform_mipi_dsim dsim_platform_data = {
+ .lcd_panel_info = NULL,
+ .dsim_config = &dsim_config,
+};
+
+static struct mipi_dsim_lcd_device mipi_lcd_device = {
+ .name = "s6e8ax0",
+ .id = -1,
+ .bus_id = 0,
+ .platform_data = (void *)&dsim_platform_data,
+};
+
+static int mipi_power(void)
+{
+ struct pmic *p = pmic_get("MAX77686_PMIC");
+
+ /* LDO8 VMIPI_1.0V_AP */
+ max77686_set_ldo_mode(p, 8, OPMODE_ON);
+ /* LDO10 VMIPI_1.8V_AP */
+ max77686_set_ldo_mode(p, 10, OPMODE_ON);
+
+ return 0;
+}
+
+void exynos_lcd_power_on(void)
+{
+ struct pmic *p = pmic_get("MAX77686_PMIC");
+
+ gpio1 = (struct exynos4x12_gpio_part1 *)EXYNOS4X12_GPIO_PART1_BASE;
+
+ /* LCD_2.2V_EN: GPC0[1] */
+ s5p_gpio_set_pull(&gpio1->c0, 1, GPIO_PULL_UP);
+ s5p_gpio_direction_output(&gpio1->c0, 1, 1);
+
+ /* LDO25 VCC_3.1V_LCD */
+ pmic_probe(p);
+ max77686_set_ldo_voltage(p, 25, 3100000);
+ max77686_set_ldo_mode(p, 25, OPMODE_LPM);
+}
+
+void exynos_reset_lcd(void)
+{
+ gpio1 = (struct exynos4x12_gpio_part1 *)EXYNOS4X12_GPIO_PART1_BASE;
+
+ /* reset lcd */
+ s5p_gpio_direction_output(&gpio1->f2, 1, 0);
+ udelay(10);
+ s5p_gpio_set_value(&gpio1->f2, 1, 1);
+}
+
+vidinfo_t panel_info = {
+ .vl_freq = 60,
+ .vl_col = 720,
+ .vl_row = 1280,
+ .vl_width = 720,
+ .vl_height = 1280,
+ .vl_clkp = CONFIG_SYS_HIGH,
+ .vl_hsp = CONFIG_SYS_LOW,
+ .vl_vsp = CONFIG_SYS_LOW,
+ .vl_dp = CONFIG_SYS_LOW,
+ .vl_bpix = 5, /* Bits per pixel, 2^5 = 32 */
+
+ /* s6e8ax0 Panel infomation */
+ .vl_hspw = 5,
+ .vl_hbpd = 10,
+ .vl_hfpd = 10,
+
+ .vl_vspw = 2,
+ .vl_vbpd = 1,
+ .vl_vfpd = 13,
+ .vl_cmd_allow_len = 0xf,
+ .mipi_enabled = 1,
+
+ .dual_lcd_enabled = 0,
+
+ .init_delay = 0,
+ .power_on_delay = 25,
+ .reset_delay = 0,
+ .interface_mode = FIMD_RGB_INTERFACE,
+};
+
+void init_panel_info(vidinfo_t *vid)
+{
+ vid->logo_on = 1;
+ vid->resolution = HD_RESOLUTION;
+ vid->rgb_mode = MODE_RGB_P;
+
+ vid->power_on_delay = 30;
+
+ mipi_lcd_device.reverse_panel = 1;
+
+#ifdef CONFIG_TIZEN
+ get_tizen_logo_info(vid);
+#endif
+
+ strcpy(dsim_platform_data.lcd_panel_name, mipi_lcd_device.name);
+ dsim_platform_data.mipi_power = mipi_power;
+ dsim_platform_data.phy_enable = set_mipi_phy_ctrl;
+ dsim_platform_data.lcd_panel_info = (void *)vid;
+ exynos_mipi_dsi_register_lcd_device(&mipi_lcd_device);
+
+ s6e8ax0_init();
+
+ exynos_set_dsim_platform_data(&dsim_platform_data);
+}
+#endif /* LCD */
+
+#ifdef CONFIG_MISC_INIT_R
+int misc_init_r(void)
+{
+ setenv("model", "GT-I8800");
+ setenv("board", "TRATS2");
+
+ show_hw_revision();
+
+ return 0;
+}
+#endif
projects / karo-tx-uboot.git / commitdiff