P2020RDB P2020
+ BSC9131RDB BSC9131
+
Greg Allen <gallen@arlut.utexas.edu>
UTX8245 MPC8245
Defines the string to utilize when trying to match PCIe device
tree nodes for the given platform.
+ CONFIG_SYS_PPC_E500_DEBUG_TLB
+
+ Enables a temporary TLB entry to be used during boot to work
+ around limitations in e500v1 and e500v2 external debugger
+ support. This reduces the portions of the boot code where
+ breakpoints and single stepping do not work. The value of this
+ symbol should be set to the TLB1 entry to be used for this
+ purpose.
+
- Generic CPU options:
CONFIG_SYS_BIG_ENDIAN, CONFIG_SYS_LITTLE_ENDIAN
/*
* Freescale SerDes initialization routine
*
- * Copyright (C) 2007,2011 Freescale Semicondutor, Inc.
+ * Copyright 2007,2011 Freescale Semiconductor, Inc.
* Copyright (C) 2008 MontaVista Software, Inc.
*
* Author: Li Yang <leoli@freescale.com>
COBJS-$(CONFIG_PPC_P3060) += ddr-gen3.o
COBJS-$(CONFIG_PPC_P4080) += ddr-gen3.o
COBJS-$(CONFIG_PPC_P5020) += ddr-gen3.o
+COBJS-$(CONFIG_BSC9131) += ddr-gen3.o
COBJS-$(CONFIG_CPM2) += ether_fcc.o
COBJS-$(CONFIG_OF_LIBFDT) += fdt.o
if (IS_SVR_REV(svr, 1, 0)) {
switch (SVR_SOC_VER(svr)) {
case SVR_P1013:
- case SVR_P1013_E:
case SVR_P1022:
- case SVR_P1022_E:
puts("Work-around for Erratum SATA A001 enabled\n");
}
}
puts("Work-around for Erratum SERDES-A005 enabled\n");
#endif
#if defined(CONFIG_SYS_P4080_ERRATUM_CPU22)
- puts("Work-around for Erratum CPU22 enabled\n");
+ if (SVR_MAJ(svr) < 3)
+ puts("Work-around for Erratum CPU22 enabled\n");
+#endif
+#ifdef CONFIG_SYS_FSL_ERRATUM_NMG_CPU_A011
+ /*
+ * NMG_CPU_A011 applies to P4080 rev 1.0, 2.0, fixed in 3.0
+ * also applies to P3041 rev 1.0, 1.1, P2041 rev 1.0, 1.1
+ */
+ if (SVR_SOC_VER(svr) != SVR_P4080 || SVR_MAJ(svr) < 3)
+ puts("Work-around for Erratum CPU-A011 enabled\n");
#endif
#if defined(CONFIG_SYS_FSL_ERRATUM_CPU_A003999)
puts("Work-around for Erratum CPU-A003999 enabled\n");
volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
#endif
-#if defined(CONFIG_SYS_P4080_ERRATUM_CPU22)
- flush_dcache();
- mtspr(L1CSR2, (mfspr(L1CSR2) | L1CSR2_DCWS));
- sync();
+#if defined(CONFIG_SYS_P4080_ERRATUM_CPU22) || \
+ defined(CONFIG_SYS_FSL_ERRATUM_NMG_CPU_A011)
+ /*
+ * CPU22 applies to P4080 rev 1.0, 2.0, fixed in 3.0
+ * NMG_CPU_A011 applies to P4080 rev 1.0, 2.0, fixed in 3.0
+ * also applies to P3041 rev 1.0, 1.1, P2041 rev 1.0, 1.1
+ */
+ if (SVR_SOC_VER(svr) != SVR_P4080 || SVR_MAJ(svr) < 3) {
+ flush_dcache();
+ mtspr(L1CSR2, (mfspr(L1CSR2) | L1CSR2_DCWS));
+ sync();
+ }
#endif
puts ("L2: ");
break;
case 0x1:
if (ver == SVR_8540 || ver == SVR_8560 ||
- ver == SVR_8541 || ver == SVR_8541_E ||
- ver == SVR_8555 || ver == SVR_8555_E) {
+ ver == SVR_8541 || ver == SVR_8555) {
puts("128 KB ");
/* set L2E=1, L2I=1, & L2BLKSZ=1 (128 Kbyte) */
cache_ctl = 0xc4000000;
break;
case 0x2:
if (ver == SVR_8540 || ver == SVR_8560 ||
- ver == SVR_8541 || ver == SVR_8541_E ||
- ver == SVR_8555 || ver == SVR_8555_E) {
+ ver == SVR_8541 || ver == SVR_8555) {
puts("256 KB ");
/* set L2E=1, L2I=1, & L2BLKSZ=2 (256 Kbyte) */
cache_ctl = 0xc8000000;
puts("enabled\n");
}
#elif defined(CONFIG_BACKSIDE_L2_CACHE)
- if ((SVR_SOC_VER(svr) == SVR_P2040) ||
- (SVR_SOC_VER(svr) == SVR_P2040_E)) {
+ if (SVR_SOC_VER(svr) == SVR_P2040) {
puts("N/A\n");
goto skip_l2;
}
*/
if (IS_SVR_REV(svr, 1, 0) &&
((SVR_SOC_VER(svr) == SVR_P1022) ||
- (SVR_SOC_VER(svr) == SVR_P1022_E) ||
- (SVR_SOC_VER(svr) == SVR_P1013) ||
- (SVR_SOC_VER(svr) == SVR_P1013_E))) {
+ (SVR_SOC_VER(svr) == SVR_P1013))) {
fsl_sata_reg_t *reg;
/* first SATA controller */
* disabled by the time we get called.
*/
msr = mfmsr();
- msr &= ~(MSR_ME|MSR_CE|MSR_DE);
+ msr &= ~(MSR_ME|MSR_CE);
mtmsr(msr);
setup_ivors();
/*
- * Copyright 2009-2011 Freescale Semiconductor, Inc
+ * Copyright 2009-2012 Freescale Semiconductor, Inc
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
asm volatile("isync;msync;tlbwe;isync");
+#if defined(CONFIG_SYS_PPC_E500_DEBUG_TLB)
+/*
+ * TLB entry for debuggging in AS1
+ * Create temporary TLB entry in AS0 to handle debug exception
+ * As on debug exception MSR is cleared i.e. Address space is changed
+ * to 0. A TLB entry (in AS0) is required to handle debug exception generated
+ * in AS1.
+ *
+ * TLB entry is created for IVPR + IVOR15 to map on valid OP code address
+ * bacause flash's physical address is going to change as
+ * CONFIG_SYS_FLASH_BASE_PHYS.
+ */
+ _mas0 = MAS0_TLBSEL(1) |
+ MAS0_ESEL(CONFIG_SYS_PPC_E500_DEBUG_TLB);
+ _mas1 = MAS1_VALID | MAS1_TID(0) | MAS1_IPROT |
+ MAS1_TSIZE(BOOKE_PAGESZ_4M);
+ _mas2 = FSL_BOOKE_MAS2(CONFIG_SYS_TEXT_BASE, MAS2_I|MAS2_G);
+ _mas3 = FSL_BOOKE_MAS3(flash_phys, 0, MAS3_SW|MAS3_SR|MAS3_SX);
+ _mas7 = FSL_BOOKE_MAS7(flash_phys);
+
+ mtspr(MAS0, _mas0);
+ mtspr(MAS1, _mas1);
+ mtspr(MAS2, _mas2);
+ mtspr(MAS3, _mas3);
+ mtspr(MAS7, _mas7);
+
+ asm volatile("isync;msync;tlbwe;isync");
+#endif
+
+ /* Change flash's physical address */
out_be32(&(ifc_regs->cspr_cs[0].cspr), CONFIG_SYS_CSPR0);
out_be32(&(ifc_regs->csor_cs[0].csor), CONFIG_SYS_CSOR0);
out_be32(&(ifc_regs->amask_cs[0].amask), CONFIG_SYS_AMASK0);
void cpu_init_f(void)
{
-#ifdef CONFIG_FSL_LBC
- fsl_lbc_t *lbc = LBC_BASE_ADDR;
-
- /*
- * LCRR - Clock Ratio Register - set up local bus timing
- * when needed
- */
- out_be32(&lbc->lcrr, LCRR_DBYP | LCRR_CLKDIV_8);
-
-#if defined(CONFIG_SYS_NAND_BR_PRELIM) && defined(CONFIG_SYS_NAND_OR_PRELIM)
- set_lbc_br(0, CONFIG_SYS_NAND_BR_PRELIM);
- set_lbc_or(0, CONFIG_SYS_NAND_OR_PRELIM);
-#else
-#error CONFIG_SYS_NAND_BR_PRELIM, CONFIG_SYS_NAND_OR_PRELIM must be defined
-#endif
-#endif
-#ifdef CONFIG_FSL_IFC
-#ifndef CONFIG_SYS_FSL_ERRATUM_IFC_A003399
-#if defined(CONFIG_SYS_CSPR0) && defined(CONFIG_SYS_CSOR0)
- set_ifc_cspr(IFC_CS0, CONFIG_SYS_CSPR0);
- set_ifc_amask(IFC_CS0, CONFIG_SYS_AMASK0);
- set_ifc_csor(IFC_CS0, CONFIG_SYS_CSOR0);
-#endif
-#endif
-#endif
-
#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L2_ADDR)
ccsr_l2cache_t *l2cache = (void *)CONFIG_SYS_MPC85xx_L2_ADDR;
break;
case 0x1:
if (ver == SVR_8540 || ver == SVR_8560 ||
- ver == SVR_8541 || ver == SVR_8541_E ||
- ver == SVR_8555 || ver == SVR_8555_E)
+ ver == SVR_8541 || ver == SVR_8555)
return 128;
else
return 256;
break;
case 0x2:
if (ver == SVR_8540 || ver == SVR_8560 ||
- ver == SVR_8541 || ver == SVR_8541_E ||
- ver == SVR_8555 || ver == SVR_8555_E)
+ ver == SVR_8541 || ver == SVR_8555)
return 256;
else
return 512;
int has_l2 = 1;
/* P2040/P2040E has no L2, so dont set any L2 props */
- if ((SVR_SOC_VER(get_svr()) == SVR_P2040) ||
- (SVR_SOC_VER(get_svr()) == SVR_P2040_E))
+ if (SVR_SOC_VER(get_svr()) == SVR_P2040)
has_l2 = 0;
size = (l2cfg0 & 0x3fff) * 64 * 1024;
unsigned int svr;
svr = mfspr(SPRN_SVR);
- if (SVR_SOC_VER(svr) == SVR_8569_E) {
+ if (SVR_SOC_VER(svr) == SVR_8569) {
if(IS_SVR_REV(svr, 1, 0))
do_fixup_by_compat_u32(blob, "fsl,qe",
"fsl,qe-num-snums", 46, 1);
prtcl = serdes_cfg_tbl[cfg][lane];
/* P2040[e] does not support XAUI */
- if (((ver == SVR_P2040) || (ver == SVR_P2040_E)) && (prtcl == XAUI_FM1))
+ if (ver == SVR_P2040 && prtcl == XAUI_FM1)
prtcl = NONE;
return prtcl;
return 0;
/* P2040[e] does not support XAUI */
- if (((ver == SVR_P2040) || (ver == SVR_P2040_E)) && (prtcl == XAUI_FM1))
+ if (ver == SVR_P2040 && prtcl == XAUI_FM1)
return 0;
for (i = 0; i < SRDS_MAX_LANES; i++) {
mtspr L1CSR2,r8
#endif
-#if defined(CONFIG_SYS_P4080_ERRATUM_CPU22)
- mfspr r8,L1CSR2
- oris r8,r8,(L1CSR2_DCWS)@h
- mtspr L1CSR2,r8
+#if defined(CONFIG_SYS_P4080_ERRATUM_CPU22) || \
+ defined(CONFIG_SYS_FSL_ERRATUM_NMG_CPU_A011)
+ /*
+ * CPU22 applies to P4080 rev 1.0, 2.0, fixed in 3.0
+ * NMG_CPU_A011 applies to P4080 rev 1.0, 2.0, fixed in 3.0
+ * also appleis to P3041 rev 1.0, 1.1, P2041 rev 1.0, 1.1
+ */
+ mfspr r3,SPRN_SVR
+ rlwinm r6,r3,24,~0x800 /* clear E bit */
+
+ lis r5,SVR_P4080@h
+ ori r5,r5,SVR_P4080@l
+ cmpw r6,r5
+ bne 1f
+
+ rlwinm r3,r3,0,0xf0
+ li r5,0x30
+ cmpw r3,r5
+ bge 2f
+1:
+ mfspr r3,L1CSR2
+ oris r3,r3,(L1CSR2_DCWS)@h
+ mtspr L1CSR2,r3
+2:
#endif
#ifdef CONFIG_BACKSIDE_L2_CACHE
/* skip L2 setup on P2040/P2040E as they have no L2 */
- mfspr r2,SPRN_SVR
+ mfspr r3,SPRN_SVR
+ rlwinm r6,r3,24,~0x800 /* clear E bit of SVR */
+
lis r3,SVR_P2040@h
ori r3,r3,SVR_P2040@l
- cmpw r2,r3
- beq 3f
-
- lis r3,SVR_P2040_E@h
- ori r3,r3,SVR_P2040_E@l
- cmpw r2,r3
+ cmpw r6,r3
beq 3f
/* Enable/invalidate the L2 cache */
.globl _start_e500
_start_e500:
+/* Enable debug exception */
+ li r1,MSR_DE
+ mtmsr r1
#if defined(CONFIG_SECURE_BOOT) && defined(CONFIG_E500MC)
/* ISBC uses L2 as stack.
andi. r1,r3,L1CSR0_DCE@l
beq 2b
+#if defined(CONFIG_SYS_PPC_E500_DEBUG_TLB) && !defined(CONFIG_NAND_SPL)
+/*
+ * TLB entry for debuggging in AS1
+ * Create temporary TLB entry in AS0 to handle debug exception
+ * As on debug exception MSR is cleared i.e. Address space is changed
+ * to 0. A TLB entry (in AS0) is required to handle debug exception generated
+ * in AS1.
+ */
+
+ lis r6,FSL_BOOKE_MAS0(1,
+ CONFIG_SYS_PPC_E500_DEBUG_TLB, 0)@h
+ ori r6,r6,FSL_BOOKE_MAS0(1,
+ CONFIG_SYS_PPC_E500_DEBUG_TLB, 0)@l
+
+#if !defined(CONFIG_SYS_RAMBOOT) && !defined(CONFIG_SECURE_BOOT)
+/*
+ * TLB entry is created for IVPR + IVOR15 to map on valid OP code address
+ * bacause flash's virtual address maps to 0xff800000 - 0xffffffff.
+ * and this window is outside of 4K boot window.
+ */
+ lis r7,FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_4M)@h
+ ori r7,r7,FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_4M)@l
+
+ lis r8,FSL_BOOKE_MAS2(CONFIG_SYS_MONITOR_BASE & 0xffc00000,
+ (MAS2_I|MAS2_G))@h
+ ori r8,r8,FSL_BOOKE_MAS2(CONFIG_SYS_MONITOR_BASE & 0xffc00000,
+ (MAS2_I|MAS2_G))@l
+
+ /* The 85xx has the default boot window 0xff800000 - 0xffffffff */
+ lis r9,FSL_BOOKE_MAS3(0xffc00000, 0, (MAS3_SX|MAS3_SW|MAS3_SR))@h
+ ori r9,r9,FSL_BOOKE_MAS3(0xffc00000, 0, (MAS3_SX|MAS3_SW|MAS3_SR))@l
+#elif !defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SECURE_BOOT)
+ lis r7,FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_1M)@h
+ ori r7,r7,FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_1M)@l
+
+ lis r8,FSL_BOOKE_MAS2(CONFIG_SYS_MONITOR_BASE,(MAS2_I|MAS2_G))@h
+ ori r8,r8,FSL_BOOKE_MAS2(CONFIG_SYS_MONITOR_BASE,(MAS2_I|MAS2_G))@l
+
+ lis r9,FSL_BOOKE_MAS3(CONFIG_SYS_PBI_FLASH_WINDOW, 0,
+ (MAS3_SX|MAS3_SW|MAS3_SR))@h
+ ori r9,r9,FSL_BOOKE_MAS3(CONFIG_SYS_PBI_FLASH_WINDOW, 0,
+ (MAS3_SX|MAS3_SW|MAS3_SR))@l
+#else
+/*
+ * TLB entry is created for IVPR + IVOR15 to map on valid OP code address
+ * because "nexti" will resize TLB to 4K
+ */
+ lis r7,FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256K)@h
+ ori r7,r7,FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256K)@l
+
+ lis r8,FSL_BOOKE_MAS2(CONFIG_SYS_MONITOR_BASE, (MAS2_I))@h
+ ori r8,r8,FSL_BOOKE_MAS2(CONFIG_SYS_MONITOR_BASE,
+ (MAS2_I))@l
+ lis r9,FSL_BOOKE_MAS3(CONFIG_SYS_MONITOR_BASE, 0,
+ (MAS3_SX|MAS3_SW|MAS3_SR))@h
+ ori r9,r9,FSL_BOOKE_MAS3(CONFIG_SYS_MONITOR_BASE, 0,
+ (MAS3_SX|MAS3_SW|MAS3_SR))@l
+#endif
+ mtspr MAS0,r6
+ mtspr MAS1,r7
+ mtspr MAS2,r8
+ mtspr MAS3,r9
+ tlbwe
+ isync
+#endif
+
/*
* Ne need to setup interrupt vector for NAND SPL
* because NAND SPL never compiles it.
msync
tlbwe
- lis r6,MSR_IS|MSR_DS@h
- ori r6,r6,MSR_IS|MSR_DS@l
+ lis r6,MSR_IS|MSR_DS|MSR_DE@h
+ ori r6,r6,MSR_IS|MSR_DS|MSR_DE@l
lis r7,switch_as@h
ori r7,r7,switch_as@l
7: sync /* Wait for all icbi to complete on bus */
isync
- /*
- * Re-point the IVPR at RAM
- */
- mtspr IVPR,r10
-
/*
* We are done. Do not return, instead branch to second part of board
* initialization, now running from RAM.
*/
addi r0,r10,in_ram - _start + _START_OFFSET
+
+ /*
+ * As IVPR is going to point RAM address,
+ * Make sure IVOR15 has valid opcode to support debugger
+ */
+ mtspr IVOR15,r0
+
+ /*
+ * Re-point the IVPR at RAM
+ */
+ mtspr IVPR,r10
+
mtlr r0
blr /* NEVER RETURNS! */
.globl in_ram
/*
- * Copyright 2009-2011 Freescale Semiconductor, Inc.
+ * Copyright 2009-2012 Freescale Semiconductor, Inc.
*
* This file is derived from arch/powerpc/cpu/mpc85xx/cpu.c and
* arch/powerpc/cpu/mpc86xx/cpu.c. Basically this file contains
struct cpu_type cpu_type_list [] = {
#if defined(CONFIG_MPC85xx)
CPU_TYPE_ENTRY(8533, 8533, 1),
- CPU_TYPE_ENTRY(8533, 8533_E, 1),
CPU_TYPE_ENTRY(8535, 8535, 1),
- CPU_TYPE_ENTRY(8535, 8535_E, 1),
CPU_TYPE_ENTRY(8536, 8536, 1),
- CPU_TYPE_ENTRY(8536, 8536_E, 1),
CPU_TYPE_ENTRY(8540, 8540, 1),
CPU_TYPE_ENTRY(8541, 8541, 1),
- CPU_TYPE_ENTRY(8541, 8541_E, 1),
CPU_TYPE_ENTRY(8543, 8543, 1),
- CPU_TYPE_ENTRY(8543, 8543_E, 1),
CPU_TYPE_ENTRY(8544, 8544, 1),
- CPU_TYPE_ENTRY(8544, 8544_E, 1),
CPU_TYPE_ENTRY(8545, 8545, 1),
- CPU_TYPE_ENTRY(8545, 8545_E, 1),
- CPU_TYPE_ENTRY(8547, 8547_E, 1),
+ CPU_TYPE_ENTRY(8547, 8547, 1),
CPU_TYPE_ENTRY(8548, 8548, 1),
- CPU_TYPE_ENTRY(8548, 8548_E, 1),
CPU_TYPE_ENTRY(8555, 8555, 1),
- CPU_TYPE_ENTRY(8555, 8555_E, 1),
CPU_TYPE_ENTRY(8560, 8560, 1),
CPU_TYPE_ENTRY(8567, 8567, 1),
- CPU_TYPE_ENTRY(8567, 8567_E, 1),
CPU_TYPE_ENTRY(8568, 8568, 1),
- CPU_TYPE_ENTRY(8568, 8568_E, 1),
CPU_TYPE_ENTRY(8569, 8569, 1),
- CPU_TYPE_ENTRY(8569, 8569_E, 1),
CPU_TYPE_ENTRY(8572, 8572, 2),
- CPU_TYPE_ENTRY(8572, 8572_E, 2),
CPU_TYPE_ENTRY(P1010, P1010, 1),
- CPU_TYPE_ENTRY(P1010, P1010_E, 1),
CPU_TYPE_ENTRY(P1011, P1011, 1),
- CPU_TYPE_ENTRY(P1011, P1011_E, 1),
CPU_TYPE_ENTRY(P1012, P1012, 1),
- CPU_TYPE_ENTRY(P1012, P1012_E, 1),
CPU_TYPE_ENTRY(P1013, P1013, 1),
- CPU_TYPE_ENTRY(P1013, P1013_E, 1),
- CPU_TYPE_ENTRY(P1014, P1014_E, 1),
CPU_TYPE_ENTRY(P1014, P1014, 1),
- CPU_TYPE_ENTRY(P1015, P1015_E, 1),
CPU_TYPE_ENTRY(P1015, P1015, 1),
- CPU_TYPE_ENTRY(P1016, P1016_E, 1),
CPU_TYPE_ENTRY(P1016, P1016, 1),
CPU_TYPE_ENTRY(P1017, P1017, 1),
- CPU_TYPE_ENTRY(P1017, P1017_E, 1),
CPU_TYPE_ENTRY(P1020, P1020, 2),
- CPU_TYPE_ENTRY(P1020, P1020_E, 2),
CPU_TYPE_ENTRY(P1021, P1021, 2),
- CPU_TYPE_ENTRY(P1021, P1021_E, 2),
CPU_TYPE_ENTRY(P1022, P1022, 2),
- CPU_TYPE_ENTRY(P1022, P1022_E, 2),
CPU_TYPE_ENTRY(P1023, P1023, 2),
- CPU_TYPE_ENTRY(P1023, P1023_E, 2),
CPU_TYPE_ENTRY(P1024, P1024, 2),
- CPU_TYPE_ENTRY(P1024, P1024_E, 2),
CPU_TYPE_ENTRY(P1025, P1025, 2),
- CPU_TYPE_ENTRY(P1025, P1025_E, 2),
CPU_TYPE_ENTRY(P2010, P2010, 1),
- CPU_TYPE_ENTRY(P2010, P2010_E, 1),
CPU_TYPE_ENTRY(P2020, P2020, 2),
- CPU_TYPE_ENTRY(P2020, P2020_E, 2),
CPU_TYPE_ENTRY(P2040, P2040, 4),
- CPU_TYPE_ENTRY(P2040, P2040_E, 4),
CPU_TYPE_ENTRY(P2041, P2041, 4),
- CPU_TYPE_ENTRY(P2041, P2041_E, 4),
CPU_TYPE_ENTRY(P3041, P3041, 4),
- CPU_TYPE_ENTRY(P3041, P3041_E, 4),
CPU_TYPE_ENTRY_MASK(P3060, P3060, 6, 0xf3),
- CPU_TYPE_ENTRY_MASK(P3060, P3060_E, 6, 0xf3),
CPU_TYPE_ENTRY(P4040, P4040, 4),
- CPU_TYPE_ENTRY(P4040, P4040_E, 4),
CPU_TYPE_ENTRY(P4080, P4080, 8),
- CPU_TYPE_ENTRY(P4080, P4080_E, 8),
CPU_TYPE_ENTRY(P5010, P5010, 1),
- CPU_TYPE_ENTRY(P5010, P5010_E, 1),
CPU_TYPE_ENTRY(P5020, P5020, 2),
- CPU_TYPE_ENTRY(P5020, P5020_E, 2),
+ CPU_TYPE_ENTRY(BSC9130, 9130, 1),
+ CPU_TYPE_ENTRY(BSC9131, 9131, 1),
#elif defined(CONFIG_MPC86xx)
CPU_TYPE_ENTRY(8610, 8610, 1),
CPU_TYPE_ENTRY(8641, 8641, 2),
/*
- * Copyright 2011 Freescale Semiconductor, Inc.
+ * Copyright 2011-2012 Freescale Semiconductor, Inc.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
#define CONFIG_MAX_CPUS 1
#define CONFIG_FSL_SDHC_V2_3
#define CONFIG_SYS_FSL_NUM_LAWS 12
+#define CONFIG_SYS_PPC_E500_DEBUG_TLB 3
#define CONFIG_TSECV2
#define CONFIG_SYS_FSL_SEC_COMPAT 4
#define CONFIG_FSL_SATA_V2
#elif defined(CONFIG_P1011)
#define CONFIG_MAX_CPUS 1
#define CONFIG_SYS_FSL_NUM_LAWS 12
+#define CONFIG_SYS_PPC_E500_DEBUG_TLB 2
#define CONFIG_TSECV2
#define CONFIG_FSL_PCIE_DISABLE_ASPM
#define CONFIG_SYS_FSL_SEC_COMPAT 2
#elif defined(CONFIG_P1012)
#define CONFIG_MAX_CPUS 1
#define CONFIG_SYS_FSL_NUM_LAWS 12
+#define CONFIG_SYS_PPC_E500_DEBUG_TLB 2
#define CONFIG_TSECV2
#define CONFIG_FSL_PCIE_DISABLE_ASPM
#define CONFIG_SYS_FSL_SEC_COMPAT 2
#elif defined(CONFIG_P1013)
#define CONFIG_MAX_CPUS 1
#define CONFIG_SYS_FSL_NUM_LAWS 12
+#define CONFIG_SYS_PPC_E500_DEBUG_TLB 2
#define CONFIG_TSECV2
#define CONFIG_SYS_FSL_SEC_COMPAT 2
#define CONFIG_FSL_SATA_V2
#define CONFIG_MAX_CPUS 1
#define CONFIG_FSL_SDHC_V2_3
#define CONFIG_SYS_FSL_NUM_LAWS 12
+#define CONFIG_SYS_PPC_E500_DEBUG_TLB 3
#define CONFIG_TSECV2
#define CONFIG_SYS_FSL_SEC_COMPAT 4
#define CONFIG_FSL_SATA_V2
#elif defined(CONFIG_P1015)
#define CONFIG_MAX_CPUS 1
#define CONFIG_SYS_FSL_NUM_LAWS 12
+#define CONFIG_SYS_PPC_E500_DEBUG_TLB 2
#define CONFIG_TSECV2
#define CONFIG_FSL_PCIE_DISABLE_ASPM
#define CONFIG_SYS_FSL_SEC_COMPAT 2
#elif defined(CONFIG_P1016)
#define CONFIG_MAX_CPUS 1
#define CONFIG_SYS_FSL_NUM_LAWS 12
+#define CONFIG_SYS_PPC_E500_DEBUG_TLB 2
#define CONFIG_TSECV2
#define CONFIG_FSL_PCIE_DISABLE_ASPM
#define CONFIG_SYS_FSL_SEC_COMPAT 2
#elif defined(CONFIG_P1020)
#define CONFIG_MAX_CPUS 2
#define CONFIG_SYS_FSL_NUM_LAWS 12
+#define CONFIG_SYS_PPC_E500_DEBUG_TLB 2
#define CONFIG_TSECV2
#define CONFIG_FSL_PCIE_DISABLE_ASPM
#define CONFIG_SYS_FSL_SEC_COMPAT 2
#elif defined(CONFIG_P1021)
#define CONFIG_MAX_CPUS 2
#define CONFIG_SYS_FSL_NUM_LAWS 12
+#define CONFIG_SYS_PPC_E500_DEBUG_TLB 2
#define CONFIG_TSECV2
#define CONFIG_FSL_PCIE_DISABLE_ASPM
#define CONFIG_SYS_FSL_SEC_COMPAT 2
#elif defined(CONFIG_P1022)
#define CONFIG_MAX_CPUS 2
#define CONFIG_SYS_FSL_NUM_LAWS 12
+#define CONFIG_SYS_PPC_E500_DEBUG_TLB 2
#define CONFIG_TSECV2
#define CONFIG_SYS_FSL_SEC_COMPAT 2
#define CONFIG_FSL_SATA_V2
#elif defined(CONFIG_P1024)
#define CONFIG_MAX_CPUS 2
#define CONFIG_SYS_FSL_NUM_LAWS 12
+#define CONFIG_SYS_PPC_E500_DEBUG_TLB 2
#define CONFIG_TSECV2
#define CONFIG_FSL_PCIE_DISABLE_ASPM
#define CONFIG_SYS_FSL_SEC_COMPAT 2
#elif defined(CONFIG_P1025)
#define CONFIG_MAX_CPUS 2
#define CONFIG_SYS_FSL_NUM_LAWS 12
+#define CONFIG_SYS_PPC_E500_DEBUG_TLB 2
#define CONFIG_TSECV2
#define CONFIG_FSL_PCIE_DISABLE_ASPM
#define CONFIG_SYS_FSL_SEC_COMPAT 2
#elif defined(CONFIG_P2010)
#define CONFIG_MAX_CPUS 1
#define CONFIG_SYS_FSL_NUM_LAWS 12
+#define CONFIG_SYS_PPC_E500_DEBUG_TLB 2
#define CONFIG_SYS_FSL_SEC_COMPAT 2
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000
#define CONFIG_SYS_FSL_ERRATUM_ESDHC111
#elif defined(CONFIG_P2020)
#define CONFIG_MAX_CPUS 2
#define CONFIG_SYS_FSL_NUM_LAWS 12
+#define CONFIG_SYS_PPC_E500_DEBUG_TLB 2
#define CONFIG_SYS_FSL_SEC_COMPAT 2
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000
#define CONFIG_SYS_FSL_ERRATUM_ESDHC111
#define CONFIG_SYS_FSL_USB2_PHY_ENABLE
#define CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY
#define CONFIG_SYS_FSL_ERRATUM_ESDHC111
+#define CONFIG_SYS_FSL_ERRATUM_NMG_CPU_A011
#define CONFIG_SYS_FSL_ERRATUM_CPU_A003999
#define CONFIG_SYS_FSL_ERRATUM_DDR_A003474
#define CONFIG_SYS_FSL_SRIO_MAX_PORTS 2
#define CONFIG_SYS_FSL_USB2_PHY_ENABLE
#define CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY
#define CONFIG_SYS_FSL_ERRATUM_ESDHC111
+#define CONFIG_SYS_FSL_ERRATUM_NMG_CPU_A011
#define CONFIG_SYS_FSL_ERRATUM_CPU_A003999
#define CONFIG_SYS_FSL_ERRATUM_DDR_A003474
#define CONFIG_SYS_FSL_SRIO_MAX_PORTS 2
#define CONFIG_SYS_FSL_ERRATUM_ESDHC135
#define CONFIG_SYS_FSL_ERRATUM_ESDHC136
#define CONFIG_SYS_P4080_ERRATUM_CPU22
+#define CONFIG_SYS_FSL_ERRATUM_NMG_CPU_A011
#define CONFIG_SYS_P4080_ERRATUM_SERDES8
#define CONFIG_SYS_P4080_ERRATUM_SERDES9
#define CONFIG_SYS_P4080_ERRATUM_SERDES_A001
#define CONFIG_SYS_FSL_SRIO_OB_WIN_NUM 9
#define CONFIG_SYS_FSL_SRIO_IB_WIN_NUM 5
+#elif defined(CONFIG_BSC9131)
+#define CONFIG_MAX_CPUS 1
+#define CONFIG_FSL_SDHC_V2_3
+#define CONFIG_SYS_FSL_NUM_LAWS 12
+#define CONFIG_TSECV2
+#define CONFIG_SYS_FSL_SEC_COMPAT 4
+#define CONFIG_NUM_DDR_CONTROLLERS 1
+#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000
+#define CONFIG_NAND_FSL_IFC
+#define CONFIG_SYS_FSL_ERRATUM_IFC_A003399
+#define CONFIG_SYS_FSL_ERRATUM_ESDHC111
+
#else
#error Processor type not defined for this platform
#endif
/*
* MPC85xx Internal Memory Map
*
- * Copyright 2007-2011 Freescale Semiconductor, Inc.
+ * Copyright 2007-2012 Freescale Semiconductor, Inc.
*
* Copyright(c) 2002,2003 Motorola Inc.
* Xianghua Xiao (x.xiao@motorola.com)
#define MPC85xx_PORPLLSR_DDR_RATIO 0x3e000000
#define MPC85xx_PORPLLSR_DDR_RATIO_SHIFT 25
#else
+#ifdef CONFIG_BSC9131
+#define MPC85xx_PORPLLSR_DDR_RATIO 0x00003f00
+#else
#define MPC85xx_PORPLLSR_DDR_RATIO 0x00003e00
+#endif
#define MPC85xx_PORPLLSR_DDR_RATIO_SHIFT 9
#endif
#define MPC85xx_PORPLLSR_QE_RATIO 0x3e000000
#define MPC85xx_PMUXCR_TDM 0x00014800
#define MPC85xx_PMUXCR_SPI_MASK 0x00600000
#define MPC85xx_PMUXCR_SPI 0x00000000
+#endif
+#if defined(CONFIG_BSC9131)
+#define MPC85xx_PMUXCR_TSEC2_DMA_GPIO_IRQ 0x40000000
+#define MPC85xx_PMUXCR_TSEC2_USB 0xC0000000
+#define MPC85xx_PMUXCR_TSEC2_1588_PPS 0x10000000
+#define MPC85xx_PMUXCR_TSEC2_1588_RSVD 0x30000000
+#define MPC85xx_PMUXCR_IFC_AD_GPIO 0x04000000
+#define MPC85xx_PMUXCR_IFC_AD_GPIO_MASK 0x0C000000
+#define MPC85xx_PMUXCR_IFC_AD15_GPIO 0x01000000
+#define MPC85xx_PMUXCR_IFC_AD15_TIMER2 0x02000000
+#define MPC85xx_PMUXCR_IFC_AD16_GPO8 0x00400000
+#define MPC85xx_PMUXCR_IFC_AD16_MSRCID0 0x00800000
+#define MPC85xx_PMUXCR_IFC_AD17_GPO 0x00100000
+#define MPC85xx_PMUXCR_IFC_AD17_GPO_MASK 0x00300000
+#define MPC85xx_PMUXCR_IFC_AD17_MSRCID_DSP 0x00200000
+#define MPC85xx_PMUXCR_IFC_CS2_GPO65 0x00040000
+#define MPC85xx_PMUXCR_IFC_CS2_DSP_TDI 0x00080000
+#define MPC85xx_PMUXCR_SDHC_USIM 0x00010000
+#define MPC85xx_PMUXCR_SDHC_TDM_RFS_RCK 0x00020000
+#define MPC85xx_PMUXCR_SDHC_GPIO77 0x00030000
+#define MPC85xx_PMUXCR_SDHC_RESV 0x00004000
+#define MPC85xx_PMUXCR_SDHC_TDM_TXD_RXD 0x00008000
+#define MPC85xx_PMUXCR_SDHC_GPIO_TIMER4 0x0000C000
+#define MPC85xx_PMUXCR_USB_CLK_UART_SIN 0x00001000
+#define MPC85xx_PMUXCR_USB_CLK_GPIO69 0x00002000
+#define MPC85xx_PMUXCR_USB_CLK_TIMER3 0x00003000
+#define MPC85xx_PMUXCR_USB_UART_GPIO0 0x00000400
+#define MPC85xx_PMUXCR_USB_RSVD 0x00000C00
+#define MPC85xx_PMUXCR_USB_GPIO62_TRIG_IN 0x00000800
+#define MPC85xx_PMUXCR_USB_D1_2_IIC2_SDA_SCL 0x00000100
+#define MPC85xx_PMUXCR_USB_D1_2_GPIO71_72 0x00000200
+#define MPC85xx_PMUXCR_USB_D1_2_RSVD 0x00000300
+#define MPC85xx_PMUXCR_USB_DIR_GPIO2 0x00000040
+#define MPC85xx_PMUXCR_USB_DIR_TIMER1 0x00000080
+#define MPC85xx_PMUXCR_USB_DIR_MCP_B 0x000000C0
+#define MPC85xx_PMUXCR_SPI1_UART3 0x00000010
+#define MPC85xx_PMUXCR_SPI1_SIM 0x00000020
+#define MPC85xx_PMUXCR_SPI1_CKSTP_IN_GPO74 0x00000030
+#define MPC85xx_PMUXCR_SPI1_CS2_CKSTP_OUT_B 0x00000004
+#define MPC85xx_PMUXCR_SPI1_CS2_dbg_adi1_rxen 0x00000008
+#define MPC85xx_PMUXCR_SPI1_CS2_GPO75 0x0000000C
+#define MPC85xx_PMUXCR_SPI1_CS3_ANT_TCXO_PWM 0x00000001
+#define MPC85xx_PMUXCR_SPI1_CS3_dbg_adi2_rxen 0x00000002
+#define MPC85xx_PMUXCR_SPI1_CS3_GPO76 0x00000003
#endif
u32 pmuxcr2; /* Alt. function signal multiplex control 2 */
#if defined(CONFIG_P1010) || defined(CONFIG_P1014)
#define MPC85xx_PMUXCR2_ETSECUSB_MASK 0x001f8000
#define MPC85xx_PMUXCR2_USB 0x00150000
#endif
+#if defined(CONFIG_BSC9131)
+#define MPC85xx_PMUXCR2_UART_CTS_B0_SIM_PD 0X40000000
+#define MPC85xx_PMUXCR2_UART_CTS_B0_DSP_TMS 0X80000000
+#define MPC85xx_PMUXCR2_UART_CTS_B0_GPIO42 0xC0000000
+#define MPC85xx_PMUXCR2_UART_RTS_B0_PWM2 0x10000000
+#define MPC85xx_PMUXCR2_UART_RTS_B0_DSP_TCK 0x20000000
+#define MPC85xx_PMUXCR2_UART_RTS_B0_GPIO43 0x30000000
+#define MPC85xx_PMUXCR2_UART_CTS_B1_SIM_PD 0x04000000
+#define MPC85xx_PMUXCR2_UART_CTS_B1_SRESET_B 0x08000000
+#define MPC85xx_PMUXCR2_UART_CTS_B1_GPIO44 0x0C000000
+#define MPC85xx_PMUXCR2_UART_RTS_B1_PPS_LED 0x01000000
+#define MPC85xx_PMUXCR2_UART_RTS_B1_RSVD 0x02000000
+#define MPC85xx_PMUXCR2_UART_RTS_B1_GPIO45 0x03000000
+#define MPC85xx_PMUXCR2_TRIG_OUT_ASLEEP 0x00400000
+#define MPC85xx_PMUXCR2_TRIG_OUT_DSP_TRST_B 0x00800000
+#define MPC85xx_PMUXCR2_ANT1_TIMER5 0x00100000
+#define MPC85xx_PMUXCR2_ANT1_TSEC_1588 0x00200000
+#define MPC85xx_PMUXCR2_ANT1_GPIO95_19 0x00300000
+#define MPC85xx_PMUXCR2_ANT1_TX_RX_FRAME_MAX3_LOCK 0x00040000
+#define MPC85xx_PMUXCR2_ANT1_TX_RX_FRAME_RSVD 0x00080000
+#define MPC85xx_PMUXCR2_ANT1_TX_RX_FRAME_GPIO80_20 0x000C0000
+#define MPC85xx_PMUXCR2_ANT1_DIO0_3_SPI3_CS0 0x00010000
+#define MPC85xx_PMUXCR2_ANT1_DIO0_3_ANT2_DO_3 0x00020000
+#define MPC85xx_PMUXCR2_ANT1_DIO0_3_GPIO81_84 0x00030000
+#define MPC85xx_PMUXCR2_ANT1_DIO4_7_SPI4 0x00004000
+#define MPC85xx_PMUXCR2_ANT1_DIO4_7_ANT2_DO4_7 0x00008000
+#define MPC85xx_PMUXCR2_ANT1_DIO4_7_GPIO85_88 0x0000C000
+#define MPC85xx_PMUXCR2_ANT1_DIO8_9_MAX2_1_LOCK 0x00001000
+#define MPC85xx_PMUXCR2_ANT1_DIO8_9_ANT2_DO8_9 0x00002000
+#define MPC85xx_PMUXCR2_ANT1_DIO8_9_GPIO21_22 0x00003000
+#define MPC85xx_PMUXCR2_ANT1_DIO10_11_TIMER6_7 0x00000400
+#define MPC85xx_PMUXCR2_ANT1_DIO10_11_ANT2_DO10_11 0x00000800
+#define MPC85xx_PMUXCR2_ANT1_DIO10_11_GPIO23_24 0x00000C00
+#define MPC85xx_PMUXCR2_ANT2_RSVD 0x00000100
+#define MPC85xx_PMUXCR2_ANT2_GPO90_91_DMA 0x00000300
+#define MPC85xx_PMUXCR2_ANT2_ENABLE_DIO0_10_USB 0x00000040
+#define MPC85xx_PMUXCR2_ANT2_ENABLE_DIO0_10_GPIO 0x000000C0
+#define MPC85xx_PMUXCR2_ANT2_DIO11_RSVD 0x00000010
+#define MPC85xx_PMUXCR2_ANT2_DIO11_TIMER8 0x00000020
+#define MPC85xx_PMUXCR2_ANT2_DIO11_GPIO61 0x00000030
+#define MPC85xx_PMUXCR2_ANT3_AGC_GPO53 0x00000004
+#define MPC85xx_PMUXCR2_ANT3_DO_TDM 0x00000001
+#define MPC85xx_PMUXCR2_ANT3_DO_GPIO46_49 0x00000002
+ u32 pmuxcr3;
+
+#define MPC85xx_PMUXCR3_ANT3_DO4_5_TDM 0x40000000
+#define MPC85xx_PMUXCR3_ANT3_DO4_5_GPIO_50_51 0x80000000
+#define MPC85xx_PMUXCR3_ANT3_DO6_7_TRIG_IN_SRESET_B 0x10000000
+#define MPC85xx_PMUXCR3_ANT3_DO6_7_GPIO_52_53 0x20000000
+#define MPC85xx_PMUXCR3_ANT3_DO8_MCP_B 0x04000000
+#define MPC85xx_PMUXCR3_ANT3_DO8_GPIO54 0x08000000
+#define MPC85xx_PMUXCR3_ANT3_DO9_10_CKSTP_IN_OUT 0x01000000
+#define MPC85xx_PMUXCR3_ANT3_DO9_10_GPIO55_56 0x02000000
+#define MPC85xx_PMUXCR3_ANT3_DO11_IRQ_OUT 0x00400000
+#define MPC85xx_PMUXCR3_ANT3_DO11_GPIO57 0x00800000
+#define MPC85xx_PMUXCR3_SPI2_CS2_GPO93 0x00100000
+#define MPC85xx_PMUXCR3_SPI2_CS3_GPO94 0x00040000
+#define MPC85xx_PMUXCR3_ANT2_AGC_RSVD 0x00010000
+#define MPC85xx_PMUXCR3_ANT2_GPO89 0x00030000
+ u32 pmuxcr4;
+#else
u8 res6[8];
+#endif
u32 devdisr; /* Device disable control */
#define MPC85xx_DEVDISR_PCI1 0x80000000
#define MPC85xx_DEVDISR_PCI2 0x40000000
u32 ddrdllcr; /* DDR DLL control */
u8 res14[12];
u32 lbcdllcr; /* LBC DLL control */
+#if defined(CONFIG_BSC9131)
+ u8 res15[12];
+ u32 halt_req_mask;
+#define HALTED_TO_HALT_REQ_MASK_0 0x80000000
+ u8 res18[232];
+#else
u8 res15[248];
+#endif
u32 lbiuiplldcr0; /* LBIU PLL Debug Reg 0 */
u32 lbiuiplldcr1; /* LBIU PLL Debug Reg 1 */
u32 ddrioovcr; /* DDR IO Override Control */
map_physmem(phys_addr_t paddr, unsigned long len, unsigned long flags)
{
#ifdef CONFIG_ADDR_MAP
- return (void *)(addrmap_phys_to_virt(paddr));
+ return addrmap_phys_to_virt(paddr);
#else
return (void *)((unsigned long)paddr);
#endif
#define SVR_MIN(svr) (((svr) >> 0) & 0xF) /* Minor revision field*/
/* Some parts define SVR[0:23] as the SOC version */
-#define SVR_SOC_VER(svr) (((svr) >> 8) & 0xFFFFFF) /* SOC Version fields */
+#define SVR_SOC_VER(svr) (((svr) >> 8) & 0xFFF7FF) /* SOC w/o E bit*/
/* whether MPC8xxxE (i.e. has SEC) */
#if defined(CONFIG_MPC85xx)
*/
#define SVR_8533 0x803400
-#define SVR_8533_E 0x803C00
#define SVR_8535 0x803701
-#define SVR_8535_E 0x803F01
#define SVR_8536 0x803700
-#define SVR_8536_E 0x803F00
#define SVR_8540 0x803000
#define SVR_8541 0x807200
-#define SVR_8541_E 0x807A00
#define SVR_8543 0x803200
-#define SVR_8543_E 0x803A00
#define SVR_8544 0x803401
-#define SVR_8544_E 0x803C01
#define SVR_8545 0x803102
-#define SVR_8545_E 0x803902
-#define SVR_8547_E 0x803901
+#define SVR_8547 0x803101
#define SVR_8548 0x803100
-#define SVR_8548_E 0x803900
#define SVR_8555 0x807100
-#define SVR_8555_E 0x807900
#define SVR_8560 0x807000
#define SVR_8567 0x807501
-#define SVR_8567_E 0x807D01
#define SVR_8568 0x807500
-#define SVR_8568_E 0x807D00
#define SVR_8569 0x808000
-#define SVR_8569_E 0x808800
#define SVR_8572 0x80E000
-#define SVR_8572_E 0x80E800
#define SVR_P1010 0x80F100
-#define SVR_P1010_E 0x80F900
#define SVR_P1011 0x80E500
-#define SVR_P1011_E 0x80ED00
#define SVR_P1012 0x80E501
-#define SVR_P1012_E 0x80ED01
#define SVR_P1013 0x80E700
-#define SVR_P1013_E 0x80EF00
#define SVR_P1014 0x80F101
-#define SVR_P1014_E 0x80F901
#define SVR_P1015 0x80E502
-#define SVR_P1015_E 0x80ED02
#define SVR_P1016 0x80E503
-#define SVR_P1016_E 0x80ED03
#define SVR_P1017 0x80F700
-#define SVR_P1017_E 0x80FF00
#define SVR_P1020 0x80E400
-#define SVR_P1020_E 0x80EC00
#define SVR_P1021 0x80E401
-#define SVR_P1021_E 0x80EC01
#define SVR_P1022 0x80E600
-#define SVR_P1022_E 0x80EE00
#define SVR_P1023 0x80F600
-#define SVR_P1023_E 0x80FE00
#define SVR_P1024 0x80E402
-#define SVR_P1024_E 0x80EC02
#define SVR_P1025 0x80E403
-#define SVR_P1025_E 0x80EC03
#define SVR_P2010 0x80E300
-#define SVR_P2010_E 0x80EB00
#define SVR_P2020 0x80E200
-#define SVR_P2020_E 0x80EA00
#define SVR_P2040 0x821000
-#define SVR_P2040_E 0x821800
#define SVR_P2041 0x821001
-#define SVR_P2041_E 0x821801
#define SVR_P3041 0x821103
-#define SVR_P3041_E 0x821903
#define SVR_P3060 0x820002
-#define SVR_P3060_E 0x820802
#define SVR_P4040 0x820100
-#define SVR_P4040_E 0x820900
#define SVR_P4080 0x820000
-#define SVR_P4080_E 0x820800
#define SVR_P5010 0x822100
-#define SVR_P5010_E 0x822900
#define SVR_P5020 0x822000
-#define SVR_P5020_E 0x822800
#define SVR_8610 0x80A000
#define SVR_8641 0x809000
#define SVR_8641D 0x809001
+#define SVR_9130 0x860001
+#define SVR_9130_E 0x860801
+#define SVR_9131 0x860000
+#define SVR_9131_E 0x860800
+
#define SVR_Unknown 0xFFFFFF
#define _GLOBAL(n)\
--- /dev/null
+#
+# Copyright 2011-2012 Freescale Semiconductor, Inc.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).o
+
+COBJS-y += $(BOARD).o
+COBJS-y += ddr.o
+COBJS-y += law.o
+COBJS-y += tlb.o
+#COBJS-y += bsc9131rdb_mux.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS-y))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(call cmd_link_o_target, $(OBJS))
+
+clean:
+ rm -f $(OBJS) $(SOBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
--- /dev/null
+Overview
+--------
+- BSC9131 is integrated device that targets Femto base station market.
+ It combines Power Architecture e500v2 and DSP StarCore SC3850 core
+ technologies with MAPLE-B2F baseband acceleration processing elements.
+- It's MAPLE disabled personality is called 9231.
+
+The BSC9131 SoC includes the following function and features:
+. Power Architecture subsystem including a e500 processor with 256-Kbyte shared
+ L2 cache
+. StarCore SC3850 DSP subsystem with a 512-Kbyte private L2 cache
+. The Multi Accelerator Platform Engine for Femto BaseStation Baseband
+ Processing (MAPLE-B2F)
+. A multi-standard baseband algorithm accelerator for Channel Decoding/Encoding,
+ Fourier Transforms, UMTS chip rate processing, LTE UP/DL Channel processing,
+ and CRC algorithms
+. Consists of accelerators for Convolution, Filtering, Turbo Encoding,
+ Turbo Decoding, Viterbi decoding, Chiprate processing, and Matrix Inversion
+ operations
+. DDR3/3L memory interface with 32-bit data width without ECC and 16-bit with
+ ECC, up to 400-MHz clock/800 MHz data rate
+. Dedicated security engine featuring trusted boot
+. DMA controller
+. OCNDMA with four bidirectional channels
+. Interfaces
+. Two triple-speed Gigabit Ethernet controllers featuring network acceleration
+ including IEEE 1588. v2 hardware support and virtualization (eTSEC)
+. eTSEC 1 supports RGMII/RMII
+. eTSEC 2 supports RGMII
+. High-speed USB 2.0 host and device controller with ULPI interface
+. Enhanced secure digital (SD/MMC) host controller (eSDHC)
+. Antenna interface controller (AIC), supporting three industry standard
+ JESD207/three custom ADI RF interfaces (two dual port and one single port)
+ and three MAXIM's MaxPHY serial interfaces
+. ADI lanes support both full duplex FDD support and half duplex TDD support
+. Universal Subscriber Identity Module (USIM) interface that facilitates
+ communication to SIM cards or Eurochip pre-paid phone cards
+. TDM with one TDM port
+. Two DUART, four eSPI, and two I2C controllers
+. Integrated Flash memory controller (IFC)
+. TDM with 256 channels
+. GPIO
+. Sixteen 32-bit timers
+
+The e500 core subsystem within the Power Architecture consists of the following:
+. 32-Kbyte L1 instruction cache
+. 32-Kbyte L1 data cache
+. 256-Kbyte L2 cache/L2 memory/L2 stash
+. programmable interrupt controller (PIC)
+. Debug support
+. Timers
+
+The SC3850 core subsystem consists of the following:
+. 32 Kbyte 8-way level 1 instruction cache (L1 ICache)
+. 32 Kbyte 8-way level 1 data cache (L1 DCache)
+. 512 Kbyte 8-way level 2 unified instruction/data cache (M2 memory)
+. Memory management unit (MMU)
+. Enhanced programmable interrupt controller (EPIC)
+. Debug and profiling unit (DPU)
+. Two 32-bit timers
+
+BSC9131RDB board Overview
+-------------------------
+ 1Gbyte DDR3 (on board DDR)
+ 128Mbyte 2K page size NAND Flash
+ 256 Kbit M24256 I2C EEPROM
+ 128 Mbit SPI Flash memory
+ USB-ULPI
+ eTSEC1: Connected to RGMII PHY
+ eTSEC2: Connected to RGMII PHY
+ DUART interface: supports one UARTs up to 115200 bps for console display
+ USIM connector
+
+Frequency Combinations Supported
+--------------------------------
+Core MHz/CCB MHz/DDR(MT/s)
+1. 1000/500/800
+2. 800/400/667
+
+Boot Methods Supported
+-----------------------
+1. NAND Flash
+2. SPI Flash
+
+Default Boot Method
+--------------------
+NAND boot
+
+Building U-boot
+--------------
+To build the u-boot for BSC9131RDB:
+1. NAND Flash
+ make BSC9131RDB_NAND
+2. SPI Flash
+ make BSC9131RDB_SPIFLASH
+
+Memory map
+-----------
+ 0x0000_0000 0x7FFF_FFFF DDR 1G cacheable
+ 0xA0000000 0xBFFFFFFF Shared DSP core L2/M2 space 512M
+ 0xC100_0000 0xC13F_FFFF MAPLE-2F 4M
+ 0xC1F0_0000 0xC1F3_FFFF PA SRAM Region 0 256K
+ 0xC1F8_0000 0xC1F9_FFFF PA SRAM Region 1 128K
+ 0xFED0_0000 0xFED0_3FFF SEC Secured RAM 16K
+ 0xFEE0_0000 0xFEE0_0FFF DSP Boot ROM 4K
+ 0xFF60_0000 0xFF6F_FFFF DSP CCSR 1M
+ 0xFF70_0000 0xFF7F_FFFF PA CCSR 1M
+ 0xFF80_0000 0xFFFF_FFFF Boot Page & NAND Buffer 8M
+
+Flashing Images
+---------------
+To place a new u-boot image in the NAND flash and then boot
+with that new image temporarily, use this:
+ tftp 1000000 u-boot-nand.bin
+ nand erase 0 100000
+ nand write 1000000 0 100000
+ reset
+
+Using the Device Tree Source File
+---------------------------------
+To create the DTB (Device Tree Binary) image file,
+use a command similar to this:
+
+ dtc -b 0 -f -I dts -O dtb bsc9131rdb.dts > bsc9131rdb.dtb
+
+Likely, that .dts file will come from here;
+
+ linux-2.6/arch/powerpc/boot/dts/bsc9131rdb.dts
+
+Booting Linux
+-------------
+Place a linux uImage in the TFTP disk area.
+
+ tftp 1000000 uImage
+ tftp 2000000 rootfs.ext2.gz.uboot
+ tftp c00000 bsc9131rdb.dtb
+ bootm 1000000 2000000 c00000
--- /dev/null
+/*
+ * Copyright 2011-2012 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/processor.h>
+#include <asm/mmu.h>
+#include <asm/cache.h>
+#include <asm/immap_85xx.h>
+#include <asm/io.h>
+#include <miiphy.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <fsl_mdio.h>
+#include <tsec.h>
+#include <netdev.h>
+
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_early_init_f(void)
+{
+ ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
+
+ clrbits_be32(&gur->pmuxcr2, MPC85xx_PMUXCR2_UART_CTS_B0_GPIO42);
+ setbits_be32(&gur->pmuxcr2, MPC85xx_PMUXCR2_UART_CTS_B0_DSP_TMS);
+
+ clrbits_be32(&gur->pmuxcr2, MPC85xx_PMUXCR2_UART_RTS_B0_GPIO43);
+ setbits_be32(&gur->pmuxcr2, MPC85xx_PMUXCR2_UART_RTS_B0_DSP_TCK |
+ MPC85xx_PMUXCR2_UART_CTS_B1_SIM_PD);
+ setbits_be32(&gur->halt_req_mask, HALTED_TO_HALT_REQ_MASK_0);
+ clrsetbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_IFC_AD_GPIO_MASK |
+ MPC85xx_PMUXCR_IFC_AD17_GPO_MASK,
+ MPC85xx_PMUXCR_IFC_AD_GPIO |
+ MPC85xx_PMUXCR_IFC_AD17_GPO | MPC85xx_PMUXCR_SDHC_USIM);
+
+ return 0;
+}
+
+int checkboard(void)
+{
+ struct cpu_type *cpu;
+
+ cpu = gd->cpu;
+ printf("Board: %sRDB\n", cpu->name);
+
+ return 0;
+}
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup(void *blob, bd_t *bd)
+{
+ phys_addr_t base;
+ phys_size_t size;
+
+ ft_cpu_setup(blob, bd);
+
+ base = getenv_bootm_low();
+ size = getenv_bootm_size();
+
+ fdt_fixup_memory(blob, (u64)base, (u64)size);
+
+ fdt_fixup_dr_usb(blob, bd);
+}
+#endif
--- /dev/null
+/*
+ * Copyright 2011-2012 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/mmu.h>
+#include <asm/immap_85xx.h>
+#include <asm/processor.h>
+#include <asm/fsl_ddr_sdram.h>
+#include <asm/fsl_ddr_dimm_params.h>
+#include <asm/io.h>
+#include <asm/fsl_law.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#ifndef CONFIG_SYS_DDR_RAW_TIMING
+#define CONFIG_SYS_DRAM_SIZE 1024
+
+fsl_ddr_cfg_regs_t ddr_cfg_regs_800 = {
+ .cs[0].bnds = CONFIG_SYS_DDR_CS0_BNDS,
+ .cs[0].config = CONFIG_SYS_DDR_CS0_CONFIG,
+ .cs[0].config_2 = CONFIG_SYS_DDR_CS0_CONFIG_2,
+ .timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3_800,
+ .timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0_800,
+ .timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1_800,
+ .timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2_800,
+ .ddr_sdram_cfg = CONFIG_SYS_DDR_CONTROL,
+ .ddr_sdram_cfg_2 = CONFIG_SYS_DDR_CONTROL_2,
+ .ddr_sdram_mode = CONFIG_SYS_DDR_MODE_1_800,
+ .ddr_sdram_mode_2 = CONFIG_SYS_DDR_MODE_2_800,
+ .ddr_sdram_md_cntl = CONFIG_SYS_DDR_MODE_CONTROL,
+ .ddr_sdram_interval = CONFIG_SYS_DDR_INTERVAL_800,
+ .ddr_data_init = CONFIG_MEM_INIT_VALUE,
+ .ddr_sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CTRL_800,
+ .ddr_init_addr = CONFIG_SYS_DDR_INIT_ADDR,
+ .ddr_init_ext_addr = CONFIG_SYS_DDR_INIT_EXT_ADDR,
+ .timing_cfg_4 = CONFIG_SYS_DDR_TIMING_4,
+ .timing_cfg_5 = CONFIG_SYS_DDR_TIMING_5,
+ .ddr_zq_cntl = CONFIG_SYS_DDR_ZQ_CONTROL,
+ .ddr_wrlvl_cntl = CONFIG_SYS_DDR_WRLVL_CONTROL_800,
+ .ddr_sr_cntr = CONFIG_SYS_DDR_SR_CNTR,
+ .ddr_sdram_rcw_1 = CONFIG_SYS_DDR_RCW_1,
+ .ddr_sdram_rcw_2 = CONFIG_SYS_DDR_RCW_2
+};
+
+fixed_ddr_parm_t fixed_ddr_parm_0[] = {
+ {750, 850, &ddr_cfg_regs_800},
+ {0, 0, NULL}
+};
+
+unsigned long get_sdram_size(void)
+{
+ return get_ram_size(CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DRAM_SIZE);
+}
+
+/*
+ * Fixed sdram init -- doesn't use serial presence detect.
+ */
+phys_size_t fixed_sdram(void)
+{
+ int i;
+ char buf[32];
+ fsl_ddr_cfg_regs_t ddr_cfg_regs;
+ phys_size_t ddr_size;
+ ulong ddr_freq, ddr_freq_mhz;
+
+ ddr_freq = get_ddr_freq(0);
+ ddr_freq_mhz = ddr_freq / 1000000;
+
+ printf("Configuring DDR for %s MT/s data rate\n",
+ strmhz(buf, ddr_freq));
+
+ for (i = 0; fixed_ddr_parm_0[i].max_freq > 0; i++) {
+ if ((ddr_freq_mhz > fixed_ddr_parm_0[i].min_freq) &&
+ (ddr_freq_mhz <= fixed_ddr_parm_0[i].max_freq)) {
+ memcpy(&ddr_cfg_regs, fixed_ddr_parm_0[i].ddr_settings,
+ sizeof(ddr_cfg_regs));
+ break;
+ }
+ }
+
+ if (fixed_ddr_parm_0[i].max_freq == 0) {
+ panic("Unsupported DDR data rate %s MT/s data rate\n",
+ strmhz(buf, ddr_freq));
+ }
+
+ ddr_size = (phys_size_t) CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
+ fsl_ddr_set_memctl_regs(&ddr_cfg_regs, 0);
+
+ if (set_ddr_laws(CONFIG_SYS_DDR_SDRAM_BASE, ddr_size,
+ LAW_TRGT_IF_DDR_1) < 0) {
+ printf("ERROR setting Local Access Windows for DDR\n");
+ return 0;
+ }
+
+ return ddr_size;
+}
+
+#else /* CONFIG_SYS_DDR_RAW_TIMING */
+/* Micron MT41J256M8HX-15E */
+dimm_params_t ddr_raw_timing = {
+ .n_ranks = 1,
+ .rank_density = 1073741824u,
+ .capacity = 1073741824u,
+ .primary_sdram_width = 32,
+ .ec_sdram_width = 0,
+ .registered_dimm = 0,
+ .mirrored_dimm = 0,
+ .n_row_addr = 15,
+ .n_col_addr = 10,
+ .n_banks_per_sdram_device = 8,
+ .edc_config = 0,
+ .burst_lengths_bitmask = 0x0c,
+
+ .tCKmin_X_ps = 1870,
+ .caslat_X = 0x1e << 4, /* 5,6,7,8 */
+ .tAA_ps = 13125,
+ .tWR_ps = 15000,
+ .tRCD_ps = 13125,
+ .tRRD_ps = 7500,
+ .tRP_ps = 13125,
+ .tRAS_ps = 37500,
+ .tRC_ps = 50625,
+ .tRFC_ps = 160000,
+ .tWTR_ps = 7500,
+ .tRTP_ps = 7500,
+ .refresh_rate_ps = 7800000,
+ .tFAW_ps = 37500,
+};
+
+int fsl_ddr_get_dimm_params(dimm_params_t *pdimm,
+ unsigned int controller_number,
+ unsigned int dimm_number)
+{
+ const char dimm_model[] = "Fixed DDR on board";
+
+ if ((controller_number == 0) && (dimm_number == 0)) {
+ memcpy(pdimm, &ddr_raw_timing, sizeof(dimm_params_t));
+ memset(pdimm->mpart, 0, sizeof(pdimm->mpart));
+ memcpy(pdimm->mpart, dimm_model, sizeof(dimm_model) - 1);
+ }
+
+ return 0;
+}
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+ dimm_params_t *pdimm,
+ unsigned int ctrl_num)
+{
+ int i;
+ popts->clk_adjust = 6;
+ popts->cpo_override = 0x1f;
+ popts->write_data_delay = 2;
+ popts->half_strength_driver_enable = 1;
+ /* Write leveling override */
+ popts->wrlvl_en = 1;
+ popts->wrlvl_override = 1;
+ popts->wrlvl_sample = 0xf;
+ popts->wrlvl_start = 0x8;
+ popts->trwt_override = 1;
+ popts->trwt = 0;
+
+ for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
+ popts->cs_local_opts[i].odt_rd_cfg = FSL_DDR_ODT_NEVER;
+ popts->cs_local_opts[i].odt_wr_cfg = FSL_DDR_ODT_CS;
+ }
+}
+
+#endif /* CONFIG_SYS_DDR_RAW_TIMING */
--- /dev/null
+/*
+ * Copyright 2011-2012 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/fsl_law.h>
+#include <asm/mmu.h>
+
+struct law_entry law_table[] = {
+ SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_IFC),
+};
+
+int num_law_entries = ARRAY_SIZE(law_table);
--- /dev/null
+/*
+ * Copyright 2011-2012 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/mmu.h>
+
+struct fsl_e_tlb_entry tlb_table[] = {
+ /* TLB 0 - for temp stack in cache */
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024 ,
+ CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024 ,
+ CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024 ,
+ CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+
+ /* TLB 1 */
+ /* *I*** - Covers boot page */
+ SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 0, BOOKE_PAGESZ_4K, 1),
+
+ /* *I*G* - CCSRBAR (PA) */
+ SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 1, BOOKE_PAGESZ_1M, 1),
+
+#if defined(CONFIG_SYS_RAMBOOT)
+ SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 8, BOOKE_PAGESZ_1G, 1),
+#endif
+
+ SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 3, BOOKE_PAGESZ_1M, 1)
+
+};
+
+int num_tlb_entries = ARRAY_SIZE(tlb_table);
* ... update that Ethernet node's phy-handle property to point to the
* ethernet-phy node. This is how we link an Ethernet node to its PHY, so each
* PHY in a virtual MDIO node must have an alias.
+ *
+ * Returns 0 on success, or a negative FDT error code on error.
*/
-void fdt_set_phy_handle(void *fdt, char *compat, phys_addr_t addr,
+int fdt_set_phy_handle(void *fdt, char *compat, phys_addr_t addr,
const char *alias)
{
- int offset, ph;
+ int offset;
+ unsigned int ph;
const char *path;
/* Get a path to the node that 'alias' points to */
path = fdt_get_alias(fdt, alias);
- if (path) {
- /* Get the offset of that node */
- int off = fdt_path_offset(fdt, path);
- if (off > 0)
- ph = fdt_create_phandle(fdt, off);
- else
- return;
- } else {
- return ;
- }
+ if (!path)
+ return -FDT_ERR_BADPATH;
+
+ /* Get the offset of that node */
+ offset = fdt_path_offset(fdt, path);
+ if (offset < 0)
+ return offset;
- /* failed to create a phandle */
- if (ph <= 0)
- return ;
+ ph = fdt_create_phandle(fdt, offset);
+ if (!ph)
+ return -FDT_ERR_BADPHANDLE;
offset = fdt_node_offset_by_compat_reg(fdt, compat, addr);
- if (offset > 0)
- fdt_setprop(fdt, offset, "phy-handle", &ph, sizeof(ph));
+ if (offset < 0)
+ return offset;
+
+ return fdt_setprop(fdt, offset, "phy-handle", &ph, sizeof(ph));
}
#ifndef __FMAN_BOARD_HELPER__
#define __FMAN_BOARD_HELPER__
-void fdt_set_phy_handle(void *fdt, char *compat, phys_addr_t addr,
+int fdt_set_phy_handle(void *fdt, char *compat, phys_addr_t addr,
const char *alias);
#endif
/*
- * Copyright 2008-2010, 2011 Freescale Semiconductor, Inc.
+ * Copyright 2008-2012 Freescale Semiconductor, Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
#ifdef CONFIG_FSL_SGMII_RISER
fsl_sgmii_riser_fdt_fixup(blob);
#endif
+
+#ifdef CONFIG_HAS_FSL_MPH_USB
+ fdt_fixup_dr_usb(blob, bd);
+#endif
+
}
#endif
--- /dev/null
+Overview
+=========
+The P1010RDB is a Freescale reference design board that hosts the P1010 SoC.
+
+The P1010 is a cost-effective, low-power, highly integrated host processor
+based on a Power Architecture e500v2 core (maximum core frequency 800/1000 MHz),
+that addresses the requirements of several routing, gateways, storage, consumer,
+and industrial applications. Applications of interest include the main CPUs and
+I/O processors in network attached storage (NAS), the voice over IP (VoIP)
+router/gateway, and wireless LAN (WLAN) and industrial controllers.
+
+The P1010RDB board features are as follows:
+Memory subsystem:
+ - 1Gbyte unbuffered DDR3 SDRAM discrete devices (32-bit bus)
+ - 32 Mbyte NOR flash single-chip memory
+ - 32 Mbyte NAND flash memory
+ - 256 Kbit M24256 I2C EEPROM
+ - 16 Mbyte SPI memory
+ - I2C Board EEPROM 128x8 bit memory
+ - SD/MMC connector to interface with the SD memory card
+Interfaces:
+ - PCIe:
+ - Lane0: x1 mini-PCIe slot
+ - Lane1: x1 PCIe standard slot
+ - SATA:
+ - 1 internal SATA connector to 2.5” 160G SATA2 HDD
+ - 1 eSATA connector to rear panel
+ - 10/100/1000 BaseT Ethernet ports:
+ - eTSEC1, RGMII: one 10/100/1000 port using Vitesse VSC8641XKO
+ - eTSEC2, SGMII: one 10/100/1000 port using Vitesse VSC8221
+ - eTSEC3, SGMII: one 10/100/1000 port using Vitesse VSC8221
+ - USB 2.0 port:
+ - x1 USB2.0 port via an external ULPI PHY to micro-AB connector
+ - x1 USB2.0 port via an internal UTMI PHY to micro-AB connector
+ - FlexCAN ports:
+ - 2 DB-9 female connectors for FlexCAN bus(revision 2.0B)
+ interface;
+ - DUART interface:
+ - DUART interface: supports two UARTs up to 115200 bps for
+ console display
+ - RJ45 connectors are used for these 2 UART ports.
+ - TDM
+ - 2 FXS ports connected via an external SLIC to the TDM interface.
+ SLIC is controllled via SPI.
+ - 1 FXO port connected via a relay to FXS for switchover to POTS
+Board connectors:
+ - Mini-ITX power supply connector
+ - JTAG/COP for debugging
+IEEE Std. 1588 signals for test and measurement
+Real-time clock on I2C bus
+POR
+ - support critical POR setting changed via switch on board
+PCB
+ - 6-layer routing (4-layer signals, 2-layer power and ground)
+
+
+Physical Memory Map on P1010RDB
+===============================
+Address Start Address End Memory type Attributes
+0x0000_0000 0x3fff_ffff DDR 1G Cacheable
+0xa000_0000 0xdfff_ffff PCI Express Mem 1G non-cacheable
+0xee00_0000 0xefff_ffff NOR Flash 32M non-cacheable
+0xffc2_0000 0xffc5_ffff PCI IO range 256K non-cacheable
+0xffa0_0000 0xffaf_ffff NAND Flash 1M cacheable
+0xffb0_0000 0xffbf_ffff Board CPLD 1M non-cacheable
+0xffd0_0000 0xffd0_3fff L1 for Stack 16K Cacheable TLB0
+0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable
+
+
+Serial Port Configuration on P1010RDB
+=====================================
+Configure the serial port of the attached computer with the following values:
+ -Data rate: 115200 bps
+ -Number of data bits: 8
+ -Parity: None
+ -Number of Stop bits: 1
+ -Flow Control: Hardware/None
+
+
+Settings of DIP-switch
+======================
+ SW4[1:4]= 1111 and SW6[4]=0 for boot from 16bit NOR flash
+ SW4[1:4]= 1000 and SW6[4]=1 for boot from 8bit NAND flash
+ SW4[1:4]= 0110 and SW6[4]=0 for boot from SPI flash
+Note: 1 stands for 'on', 0 stands for 'off'
+
+
+Setting of hwconfig
+===================
+If FlexCAN or TDM is needed, please set "fsl_p1010mux:tdm_can=can" or
+"fsl_p1010mux:tdm_can=tdm" explicitly in u-booot prompt as below for example:
+setenv hwconfig "fsl_p1010mux:tdm_can=tdm;usb1:dr_mode=host,phy_type=utmi"
+By default, don't set fsl_p1010mux:tdm_can, in this case, spi chip selection
+is set to spi-flash instead of to SLIC/TDM/DAC and tdm_can_sel is set to TDM
+instead of to CAN/UART1.
+
+
+Build and burn u-boot to NOR flash
+==================================
+1. Build u-boot.bin image
+ export ARCH=powerpc
+ export CROSS_COMPILE=/your_path/powerpc-linux-gnu-
+ make P1010RDB_NOR
+
+2. Burn u-boot.bin into NOR flash
+ => tftp $loadaddr $uboot
+ => protect off eff80000 +$filesize
+ => erase eff80000 +$filesize
+ => cp.b $loadaddr eff80000 $filesize
+
+3. Check SW4[1:4]= 1111 and SW6[4]=0, then power on.
+
+
+Alternate NOR bank
+==================
+1. Burn u-boot.bin into alternate NOR bank
+ => tftp $loadaddr $uboot
+ => protect off eef80000 +$filesize
+ => erase eef80000 +$filesize
+ => cp.b $loadaddr eef80000 $filesize
+
+2. Switch to alternate NOR bank
+ => mw.b ffb00009 1
+ => reset
+ or set SW1[8]= ON
+
+SW1[8]= OFF: Upper bank used for booting start
+SW1[8]= ON: Lower bank used for booting start
+CPLD NOR bank selection register address 0xFFB00009 Bit[0]:
+0 - boot from upper 4 sectors
+1 - boot from lower 4 sectors
+
+
+Build and burn u-boot to NAND flash
+===================================
+1. Build u-boot.bin image
+ export ARCH=powerpc
+ export CROSS_COMPILE=/your_path/powerpc-linux-gnu-
+ make P1010RDB_NAND
+
+2. Burn u-boot-nand.bin into NAND flash
+ => tftp $loadaddr $uboot-nand
+ => nand erase 0 $filesize
+ => nand write $loadaddr 0 $filesize
+
+3. Check SW4[1:4]= 1000 and SW6[4]=1, then power on.
+
+
+
+Build and burn u-boot to SPI flash
+==================================
+1. Build u-boot-spi.bin image
+ make P1010RDB_SPIFLASH_config; make
+ Boot up kernel with rootfs.ext2.gz.uboot.p1010rdb
+ Download u-boot.bin to linux and you can find some config files
+ under /usr/share such as config_xx.dat. Do below command:
+ boot_format config_ddr3_1gb_p1010rdb_800M.dat u-boot.bin -spi \
+ u-boot-spi.bin
+ to generate u-boot-spi.bin.
+
+2. Burn u-boot-spi.bin into SPI flash
+ => tftp $loadaddr $uboot-spi
+ => sf erase 0 100000
+ => sf write $loadaddr 0 $filesize
+
+3. Check SW4[1:4]= 0110 and SW6[4]=0, then power on.
+
+
+
+CPLD POR setting registers
+==========================
+1. Set POR switch selection register (addr 0xFFB00011) to 0.
+2. Write CPLD POR registers (BCSR0~BCSR3, addr 0xFFB00014~0xFFB00017) with
+ proper values.
+ If change boot ROM location to NOR or NAND flash, need write the IFC_CS0
+ switch command by I2C.
+3. Send reset command.
+ After reset, the new POR setting will be implemented.
+
+Two examples are given in below:
+Switch from NOR to NAND boot with default frequency:
+ => i2c dev 0
+ => i2c mw 18 1 f9
+ => i2c mw 18 3 f0
+ => mw.b ffb00011 0
+ => mw.b ffb00017 1
+ => reset
+Switch from NAND to NOR boot with Core/CCB/DDR (800/400/667 MHz):
+ => i2c dev 0
+ => i2c mw 18 1 f1
+ => i2c mw 18 3 f0
+ => mw.b ffb00011 0
+ => mw.b ffb00014 2
+ => mw.b ffb00015 5
+ => mw.b ffb00016 3
+ => mw.b ffb00017 f
+ => reset
+
+
+
+Boot Linux from network using TFTP on P1010RDB
+==============================================
+Place uImage, p1010rdb.dtb and rootfs files in the TFTP disk area.
+ => tftp 1000000 uImage
+ => tftp 2000000 p1010rdb.dtb
+ => tftp 3000000 rootfs.ext2.gz.uboot.p1010rdb
+ => bootm 1000000 3000000 2000000
+
+
+Please contact your local field applications engineer or sales representative
+to obtain related documents, such as P1010-RDB User Guide for details.
+
cpu = gd->cpu;
/* P1014 and it's derivatives support max 16it DDR width */
- if (cpu->soc_ver == SVR_P1014 || cpu->soc_ver == SVR_P1014_E)
+ if (cpu->soc_ver == SVR_P1014)
ddr_size = (CONFIG_SYS_DRAM_SIZE / 2);
else
ddr_size = CONFIG_SYS_DRAM_SIZE;
cpu = gd->cpu;
/* P1014 and it's derivatives support max 16bit DDR width */
- if (cpu->soc_ver == SVR_P1014 || cpu->soc_ver == SVR_P1014_E) {
+ if (cpu->soc_ver == SVR_P1014) {
ddr_cfg_regs.ddr_sdram_cfg |= SDRAM_CFG_16_BE;
ddr_cfg_regs.cs[0].bnds = CONFIG_SYS_DDR_CS0_BNDS >> 1;
ddr_cfg_regs.ddr_sdram_cfg &= ~0x00180000;
cpu = gd->cpu;
/* P1014 and it's derivatives support max 16it DDR width */
- if (cpu->soc_ver == SVR_P1014 || cpu->soc_ver == SVR_P1014_E)
+ if (cpu->soc_ver == SVR_P1014)
popts->data_bus_width = DDR_DATA_BUS_WIDTH_16;
for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
#endif
#ifdef CONFIG_TSEC3
/* P1014 and it's derivatives do not support eTSEC3 */
- if (cpu->soc_ver != SVR_P1014 && cpu->soc_ver != SVR_P1014_E) {
+ if (cpu->soc_ver != SVR_P1014) {
SET_STD_TSEC_INFO(tsec_info[num], 3);
num++;
}
}
}
+void fdt_del_sdhc(void *blob)
+{
+ int nodeoff = 0;
+
+ while ((nodeoff = fdt_node_offset_by_compatible(blob, 0,
+ "fsl,esdhc")) >= 0) {
+ fdt_del_node(blob, nodeoff);
+ }
+}
+
+void fdt_disable_uart1(void *blob)
+{
+ int nodeoff;
+
+ nodeoff = fdt_node_offset_by_compat_reg(blob, "fsl,ns16550",
+ CONFIG_SYS_NS16550_COM2);
+
+ if (nodeoff > 0) {
+ fdt_status_disabled(blob, nodeoff);
+ } else {
+ printf("WARNING unable to set status for fsl,ns16550 "
+ "uart1: %s\n", fdt_strerror(nodeoff));
+ }
+}
+
void ft_board_setup(void *blob, bd_t *bd)
{
phys_addr_t base;
#endif
/* P1014 and it's derivatives don't support CAN and eTSEC3 */
- if (cpu->soc_ver == SVR_P1014 || cpu->soc_ver == SVR_P1014_E) {
+ if (cpu->soc_ver == SVR_P1014) {
fdt_del_flexcan(blob);
fdt_del_node_and_alias(blob, "ethernet2");
}
#ifndef CONFIG_SDCARD
+ /* disable sdhc due to sdhc bug */
+ fdt_del_sdhc(blob);
if (hwconfig_subarg_cmp("fsl_p1010mux", "tdm_can", "can")) {
- printf("fdt CAN");
fdt_del_tdm(blob);
fdt_del_spi_slic(blob);
- }
-#ifndef CONFIG_SPIFLASH
- else if (hwconfig_subarg_cmp("fsl_p1010mux", "tdm_can", "tdm")) {
- printf("fdt TDM");
+ } else if (hwconfig_subarg_cmp("fsl_p1010mux", "tdm_can", "tdm")) {
fdt_del_flexcan(blob);
fdt_del_spi_flash(blob);
+ fdt_disable_uart1(blob);
+ } else {
+ /*
+ * If we don't set fsl_p1010mux:tdm_can to "can" or "tdm"
+ * explicitly, defaultly spi_cs_sel to spi-flash instead of
+ * to tdm/slic.
+ */
+ fdt_del_tdm(blob);
+ fdt_del_flexcan(blob);
+ fdt_disable_uart1(blob);
}
#endif
-#endif
}
#endif
MPC85xx_PMUXCR_CAN2_TDM |
MPC85xx_PMUXCR_CAN2_UART);
out_8(&cpld_data->tdm_can_sel, MUX_CPLD_CAN_UART);
- }
-#ifndef CONFIG_SPIFLASH
- if (hwconfig_subarg_cmp("fsl_p1010mux", "tdm_can", "tdm")) {
- printf("TDM");
+ } else if (hwconfig_subarg_cmp("fsl_p1010mux", "tdm_can", "tdm")) {
clrbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_CAN2_UART |
MPC85xx_PMUXCR_CAN1_UART);
setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_CAN2_TDM |
setbits_be32(&gur->pmuxcr2, MPC85xx_PMUXCR2_UART_TDM);
out_8(&cpld_data->tdm_can_sel, MUX_CPLD_TDM);
out_8(&cpld_data->spi_cs0_sel, MUX_CPLD_SPICS0_SLIC);
- }
-#endif
+ } else {
+ /* defaultly spi_cs_sel to flash */
+ out_8(&cpld_data->spi_cs0_sel, MUX_CPLD_SPICS0_FLASH);
+ }
+
return 0;
}
#endif
/*
- * Copyright 2010-2011 Freescale Semiconductor, Inc.
+ * Copyright 2010-2012 Freescale Semiconductor, Inc.
* Authors: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
* Timur Tabi <timur@freescale.com>
*
fdt_fixup_memory(blob, (u64)base, (u64)size);
+#ifdef CONFIG_HAS_FSL_DR_USB
+ fdt_fixup_dr_usb(blob, bd);
+#endif
+
FT_FSL_PCI_SETUP;
#ifdef CONFIG_FSL_SGMII_RISER
/*
- * Copyright 2010-2011 Freescale Semiconductor, Inc.
+ * Copyright 2010-2012 Freescale Semiconductor, Inc.
*
* Authors: Roy Zang <tie-fei.zang@freescale.com>
* Chunhe Lan <b25806@freescale.com>
do_fixup_by_path_string(blob, "nor_flash", "status", "disabled");
do_fixup_by_path_string(blob, "nand_flash", "status", "okay");
#endif
+#ifdef CONFIG_HAS_FSL_DR_USB
+ fdt_fixup_dr_usb(blob, bd);
+#endif
fdt_fixup_fman_ethernet(blob);
}
cpu = gd->cpu;
/* P1020 and it's derivatives support max 32bit DDR width */
- if (cpu->soc_ver == SVR_P1020 || cpu->soc_ver == SVR_P1020_E ||
- cpu->soc_ver == SVR_P1011 || cpu->soc_ver == SVR_P1011_E) {
+ if (cpu->soc_ver == SVR_P1020 || cpu->soc_ver == SVR_P1011) {
ddr_size = (CONFIG_SYS_SDRAM_SIZE * 1024 * 1024 / 2);
} else {
ddr_size = CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
strmhz(buf, ddr_freq));
/* P1020 and it's derivatives support max 32bit DDR width */
- if(cpu->soc_ver == SVR_P1020 || cpu->soc_ver == SVR_P1020_E ||
- cpu->soc_ver == SVR_P1011 || cpu->soc_ver == SVR_P1011_E) {
+ if (cpu->soc_ver == SVR_P1020 || cpu->soc_ver == SVR_P1011) {
ddr_cfg_regs.ddr_sdram_cfg |= SDRAM_CFG_32_BE;
ddr_cfg_regs.cs[0].bnds = 0x0000001F;
}
/*
- * Copyright 2009 Freescale Semiconductor, Inc.
+ * Copyright 2009,2012 Freescale Semiconductor, Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
fdt_fixup_memory(blob, (u64)base, (u64)size);
+#ifdef CONFIG_HAS_FSL_DR_USB
fdt_fixup_dr_usb(blob, bd);
+#endif
}
#endif
/*
- * Copyright 2007-2011 Freescale Semiconductor, Inc.
+ * Copyright 2007-2012 Freescale Semiconductor, Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
fdt_fixup_memory(blob, (u64)base, (u64)size);
+#ifdef CONFIG_HAS_FSL_DR_USB
+ fdt_fixup_dr_usb(blob, bd);
+#endif
+
FT_FSL_PCI_SETUP;
#ifdef CONFIG_FSL_SGMII_RISER
/*
- * Copyright 2011 Freescale Semiconductor, Inc.
+ * Copyright 2011,2012 Freescale Semiconductor, Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
fdt_fixup_memory(blob, (u64)base, (u64)size);
+#if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_MPH_USB)
+ fdt_fixup_dr_usb(blob, bd);
+#endif
+
#ifdef CONFIG_PCI
pci_of_setup(blob, bd);
#endif
/*
- * Copyright 2011 Freescale Semiconductor, Inc.
+ * Copyright 2011-2012 Freescale Semiconductor, Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
fdt_fixup_memory(blob, (u64)base, (u64)size);
+#if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_MPH_USB)
+ fdt_fixup_dr_usb(blob, bd);
+#endif
+
#ifdef CONFIG_PCI
pci_of_setup(blob, bd);
#endif
P5020DS_SPIFLASH powerpc mpc85xx corenet_ds freescale - P5020DS:RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF80000
P5020DS_SRIOBOOT_MASTER powerpc mpc85xx corenet_ds freescale - P5020DS:SRIOBOOT_MASTER
P5020DS_SRIOBOOT_SLAVE powerpc mpc85xx corenet_ds freescale - P5020DS:SRIOBOOT_SLAVE,SYS_TEXT_BASE=0xFFF80000
+BSC9131RDB_SPIFLASH powerpc mpc85xx bsc9131rdb freescale - BSC9131RDB:BSC9131RDB,SPIFLASH
stxgp3 powerpc mpc85xx stxgp3 stx
stxssa powerpc mpc85xx stxssa stx - stxssa
stxssa_4M powerpc mpc85xx stxssa stx - stxssa:STXSSA_4M
--- /dev/null
+External Debug Support
+----------------------
+
+Freescale's e500v1 and e500v2 cores (used in mpc85xx chips) have some
+restrictions on external debugging (JTAG). In particular, for the debugger to
+be able to receive control after a single step or breakpoint:
+ - MSR[DE] must be set
+ - A valid opcode must be fetchable, through the MMU, from the debug
+ exception vector (IVPR + IVOR15).
+
+To maximize the time during which this requirement is met, U-Boot sets MSR[DE]
+immediately on entry and keeps it set. It also uses a temporary TLB to keep a
+mapping to a valid opcode at the debug exception vector, even if we normally
+don't support exception vectors being used that early, and that's not the area
+where U-Boot currently executes from.
+
+Note that there may still be some small windows where debugging will not work,
+such as in between updating IVPR and IVOR15.
+
+Config Switches:
+----------------
+
+Please refer README section "MPC85xx External Debug Support"
+
+Major Config Switches during various boot Modes
+----------------------------------------------
+
+NOR boot
+ !defined(CONFIG_SYS_RAMBOOT)
+NOR boot Secure
+ !defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SECURE_BOOT)
+RAMBOOT(SD, SPI & NAND boot)
+ defined(CONFIG_SYS_RAMBOOT)
+RAMBOOT Secure (SD, SPI & NAND)
+ defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SECURE_BOOT)
+NAND SPL BOOT
+ defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_NAND_SPL)
+
+
+TLB Entries during u-boot execution
+-----------------------------------
+
+Note: Sequence number is in order of execution
+
+A) defined(CONFIG_SYS_RAMBOOT) i.e. SD, SPI, NAND RAMBOOT & NAND_SPL boot
+
+ 1) TLB entry to overcome e500 v1/v2 debug restriction
+ Location : Label "_start_e500"
+ TLB Entry : CONFIG_SYS_PPC_E500_DEBUG_TLB
+ EPN -->RPN : CONFIG_SYS_MONITOR_BASE --> CONFIG_SYS_MONITOR_BASE
+ Properties : 256K, AS0, I, IPROT
+
+ 2) TLB entry for working in AS1
+ Location : Label "create_init_ram_area"
+ TLB Entry : 15
+ EPN -->RPN : CONFIG_SYS_MONITOR_BASE --> CONFIG_SYS_MONITOR_BASE
+ Properties : 1M, AS1, I, G, IPROT
+
+ 3) TLB entry for the stack during AS1
+ Location : Lable "create_init_ram_area"
+ TLB Entry : 14
+ EPN -->RPN : CONFIG_SYS_INIT_RAM_ADDR --> CONFIG_SYS_INIT_RAM_ADDR
+ Properties : 16K, AS1, IPROT
+
+ 4) TLB entry for CCSRBAR during AS1 execution
+ Location : cpu_init_early_f
+ TLB Entry : 13
+ EPN -->RPN : CONFIG_SYS_CCSRBAR --> CONFIG_SYS_CCSRBAR
+ Properties : 1M, AS1, I, G
+
+ 5) Invalidate unproctected TLB Entries
+ Location : cpu_init_early_f
+ Invalidated: 13
+
+ 6) Create TLB entries as per boards/freescale/<board>/tlb.c
+ Location : cpu_init_early_f --> init_tlbs()
+ Properties : ..., AS0, ...
+ Please note It can overwrites previous TLB Entries.
+
+ 7) Disable TLB Entries of AS1
+ Location : cpu_init_f --> disable_tlb()
+ Disable : 15, 14
+
+ 8) Update Flash's TLB entry
+ Location : Board_init_r
+ TLB entry : Search from TLB entries
+ EPN -->RPN : CONFIG_SYS_FLASH_BASE --> CONFIG_SYS_FLASH_BASE_PHYS
+ Properties : Board specific size, AS0, I, G, IPROT
+
+
+B) !defined(CONFIG_SYS_RAMBOOT) i.e. NOR boot
+
+ 1) TLB entry to overcome e500 v1/v2 debug restriction
+ Location : Label "_start_e500"
+ TLB Entry : CONFIG_SYS_PPC_E500_DEBUG_TLB
+#if defined(CONFIG_SECURE_BOOT)
+ EPN -->RPN : CONFIG_SYS_MONITOR_BASE --> CONFIG_SYS_PBI_FLASH_WINDOW
+ Properties : 1M, AS1, I, G, IPROT
+#else
+ EPN -->RPN : CONFIG_SYS_MONITOR_BASE & 0xffc00000 --> 0xffc00000
+ Properties : 4M, AS0, I, G, IPROT
+#endif
+
+ 2) TLB entry for working in AS1
+ Location : Label "create_init_ram_area"
+ TLB Entry : 15
+#if defined(CONFIG_SECURE_BOOT)
+ EPN -->RPN : CONFIG_SYS_MONITOR_BASE --> CONFIG_SYS_PBI_FLASH_WINDOW
+ Properties : 1M, AS1, I, G, IPROT
+#else
+ EPN -->RPN : CONFIG_SYS_MONITOR_BASE & 0xffc00000 --> 0xffc00000
+ Properties : 4M, AS1, I, G, IPROT
+#endif
+
+ 3) TLB entry for the stack during AS1
+ Location : Lable "create_init_ram_area"
+ TLB Entry : 14
+ EPN -->RPN : CONFIG_SYS_INIT_RAM_ADDR --> CONFIG_SYS_INIT_RAM_ADDR
+ Properties : 16K, AS1, IPROT
+
+ 4) TLB entry for CCSRBAR during AS1 execution
+ Location : cpu_init_early_f
+ TLB Entry : 13
+ EPN -->RPN : CONFIG_SYS_CCSRBAR --> CONFIG_SYS_CCSRBAR
+ Properties : 1M, AS1, I, G
+
+ 5) TLB entry for Errata workaround CONFIG_SYS_FSL_ERRATUM_IFC_A003399
+ Location : cpu_init_early_f
+ TLB Entry : 9
+ EPN -->RPN : SRAM_BASE_ADDR --> SRAM_BASE_ADDR
+ Properties : 1M, AS1, I
+
+ 6) CONFIG_SYS_FSL_ERRATUM_IFC_A003399 Adjust flash's phys addr
+ Location : cpu_init_early_f --> setup_ifc
+ TLB Entry : Get Flash TLB
+ EPN -->RPN : Adjusted flash_phys --> Adjusted flash_phys
+ Properties : 4M, AS1, I, G, IPROT
+
+ 7) CONFIG_SYS_FSL_ERRATUM_IFC_A003399: E500 v1,v2 debug restriction
+ Location : cpu_init_early_f --> setup_ifc
+ TLB Entry : CONFIG_SYS_PPC_E500_DEBUG_TLB
+ EPN -->RPN : Adjusted flash_phys --> Adjusted flash_phys
+ Properties : 4M, AS0, I, G, IPROT
+
+ 8) Invalidate unproctected TLB Entries
+ Location : cpu_init_early_f
+ Invalidated: 13, 9
+
+ 9) Create TLB entries as per boards/freescale/<board>/tlb.c
+ Location : cpu_init_early_f --> init_tlbs()
+ Properties : ..., AS0, ...
+ Note: It can overwrites previous TLB Entries
+
+ 10) Disable TLB Entries of AS1
+ Location : cpu_init_f --> disable_tlb()
+ Disable : 15, 14
+
+ 11) Create DDR's TLB entriy
+ Location : Board_init_f -> init_func_ram -> initdram
+ TLB entry : Search free TLB entry
+
+ 12) Update Flash's TLB entry
+ Location : Board_init_r
+ TLB entry : Search from TLB entries
+ EPN -->RPN : CONFIG_SYS_FLASH_BASE --> CONFIG_SYS_FLASH_BASE_PHYS
+ Properties : Board specific size, AS0, I, G, IPROT
#include <asm/types.h>
extern phys_addr_t addrmap_virt_to_phys(void *vaddr);
-extern unsigned long addrmap_phys_to_virt(phys_addr_t paddr);
+extern void *addrmap_phys_to_virt(phys_addr_t paddr);
extern void addrmap_set_entry(unsigned long vaddr, phys_addr_t paddr,
phys_size_t size, int idx);
--- /dev/null
+/*
+ * Copyright 2011-2012 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * BSC9131 RDB board configuration file
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#ifdef CONFIG_BSC9131RDB
+#define CONFIG_BSC9131
+#define CONFIG_NAND_FSL_IFC
+#endif
+
+#ifdef CONFIG_SPIFLASH
+#define CONFIG_RAMBOOT_SPIFLASH
+#define CONFIG_SYS_RAMBOOT
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_SYS_TEXT_BASE 0x11000000
+#define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc
+#endif
+
+#ifndef CONFIG_SYS_MONITOR_BASE
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
+#endif
+
+/* High Level Configuration Options */
+#define CONFIG_BOOKE /* BOOKE */
+#define CONFIG_E500 /* BOOKE e500 family */
+#define CONFIG_MPC85xx /* MPC8540/60/55/41/48/P1020/P2020/P1010,etc*/
+#define CONFIG_FSL_IFC /* Enable IFC Support */
+
+#define CONFIG_FSL_LAW /* Use common FSL init code */
+#define CONFIG_TSEC_ENET
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_DDR_CLK_FREQ 66666666 /* DDRCLK on 9131 RDB */
+#define CONFIG_SYS_CLK_FREQ 66666666 /* SYSCLK for 9131 RDB */
+
+#define CONFIG_HWCONFIG
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_L2_CACHE /* toggle L2 cache */
+#define CONFIG_BTB /* enable branch predition */
+
+#define CONFIG_SYS_MEMTEST_START 0x01000000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x01ffffff
+
+/* DDR Setup */
+#define CONFIG_FSL_DDR3
+#undef CONFIG_SYS_DDR_RAW_TIMING
+#undef CONFIG_DDR_SPD
+#define CONFIG_SYS_SPD_BUS_NUM 0
+#define SPD_EEPROM_ADDRESS 0x52 /* I2C access */
+
+#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
+
+#ifndef __ASSEMBLY__
+extern unsigned long get_sdram_size(void);
+#endif
+#define CONFIG_SYS_SDRAM_SIZE get_sdram_size() /* DDR size */
+#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
+
+#define CONFIG_NUM_DDR_CONTROLLERS 1
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+#define CONFIG_CHIP_SELECTS_PER_CTRL 1
+
+#define CONFIG_SYS_DDR_CS0_BNDS 0x0000003f
+#define CONFIG_SYS_DDR_CS0_CONFIG 0x80014302
+#define CONFIG_SYS_DDR_CS0_CONFIG_2 0x00000000
+
+#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef
+#define CONFIG_SYS_DDR_INIT_ADDR 0x00000000
+#define CONFIG_SYS_DDR_INIT_EXT_ADDR 0x00000000
+#define CONFIG_SYS_DDR_MODE_CONTROL 0x00000000
+
+#define CONFIG_SYS_DDR_ZQ_CONTROL 0x89080600
+#define CONFIG_SYS_DDR_SR_CNTR 0x00000000
+#define CONFIG_SYS_DDR_RCW_1 0x00000000
+#define CONFIG_SYS_DDR_RCW_2 0x00000000
+#define CONFIG_SYS_DDR_CONTROL 0xC70C0000 /* Type = DDR3 */
+#define CONFIG_SYS_DDR_CONTROL_2 0x24401000
+#define CONFIG_SYS_DDR_TIMING_4 0x00000001
+#define CONFIG_SYS_DDR_TIMING_5 0x02401400
+
+#define CONFIG_SYS_DDR_TIMING_3_800 0x00030000
+#define CONFIG_SYS_DDR_TIMING_0_800 0x00110104
+#define CONFIG_SYS_DDR_TIMING_1_800 0x6f6b8644
+#define CONFIG_SYS_DDR_TIMING_2_800 0x0fa888cf
+#define CONFIG_SYS_DDR_CLK_CTRL_800 0x03000000
+#define CONFIG_SYS_DDR_MODE_1_800 0x00441420
+#define CONFIG_SYS_DDR_MODE_2_800 0x8000c000
+#define CONFIG_SYS_DDR_INTERVAL_800 0x0c300100
+#define CONFIG_SYS_DDR_WRLVL_CONTROL_800 0x8675f608
+
+/*
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ */
+/* relocated CCSRBAR */
+#define CONFIG_SYS_CCSRBAR CONFIG_SYS_CCSRBAR_DEFAULT
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR_DEFAULT
+
+#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses */
+ /* CONFIG_SYS_IMMR */
+
+/*
+ * Memory map
+ *
+ * 0x0000_0000 0x3FFF_FFFF DDR 1G cacheable
+ * 0x8800_0000 0x8810_0000 IFC internal SRAM 1M
+ * 0xC100_0000 0xC13F_FFFF MAPLE-2F 4M
+ * 0xC1F0_0000 0xC1F3_FFFF PA L2 SRAM Region 0 256K
+ * 0xC1F8_0000 0xC1F9_FFFF PA L2 SRAM Region 1 128K
+ * 0xFED0_0000 0xFED0_3FFF SEC Secured RAM 16K
+ * 0xFF70_0000 0xFF7F_FFFF PA CCSR 1M
+ * 0xFF80_0000 0xFFFF_FFFF Boot Page & NAND flash buffer 8M
+ *
+ */
+
+/*
+ * IFC Definitions
+ */
+#define CONFIG_SYS_NO_FLASH
+
+/* NAND Flash on IFC */
+#define CONFIG_SYS_NAND_BASE 0xff800000
+#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
+
+#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+ | CSPR_PORT_SIZE_8 /* Port Size = 8 bit*/ \
+ | CSPR_MSEL_NAND /* MSEL = NAND */ \
+ | CSPR_V)
+#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024)
+
+#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
+ | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
+ | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
+ | CSOR_NAND_RAL_2 /* RAL = 2Byes */ \
+ | CSOR_NAND_PGS_2K /* Page Size = 2K */ \
+ | CSOR_NAND_SPRZ_64 /* Spare size = 64 */ \
+ | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/
+
+/* NAND Flash Timing Params */
+#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x08) \
+ | FTIM0_NAND_TWP(0x06) \
+ | FTIM0_NAND_TWCHT(0x03) \
+ | FTIM0_NAND_TWH(0x04))
+#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x18) \
+ | FTIM1_NAND_TWBE(0x23) \
+ | FTIM1_NAND_TRR(0x08) \
+ | FTIM1_NAND_TRP(0x05))
+#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x08) \
+ | FTIM2_NAND_TREH(0x04) \
+ | FTIM2_NAND_TWHRE(0x3f))
+#define CONFIG_SYS_NAND_FTIM3 FTIM3_NAND_TWW(0x22)
+
+#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND
+#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
+
+#define CONFIG_SYS_NAND_DDR_LAW 11
+
+/* Set up IFC registers for boot location NAND */
+#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
+
+#define CONFIG_BOARD_EARLY_INIT_F /* Call board_pre_init */
+
+#define CONFIG_SYS_INIT_RAM_LOCK
+#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* stack in RAM */
+#define CONFIG_SYS_INIT_RAM_END 0x00004000/* End of used area in RAM */
+
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END \
+ - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon*/
+#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc*/
+
+/* Serial Port */
+#define CONFIG_CONS_INDEX 1
+#undef CONFIG_SERIAL_SOFTWARE_FIFO
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
+
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* determine from environment */
+
+#define CONFIG_SYS_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+#ifdef CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+#endif
+
+/*
+ * Pass open firmware flat tree
+ */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+#define CONFIG_OF_STDOUT_VIA_ALIAS
+
+/* new uImage format support */
+#define CONFIG_FIT
+#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
+
+#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C /* I2C with hardware support */
+#undef CONFIG_SOFT_I2C /* I2C bit-banged */
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_I2C_CMD_TREE
+#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address*/
+#define CONFIG_SYS_I2C_OFFSET 0x3000
+
+/* I2C EEPROM */
+#define CONFIG_CMD_EEPROM
+#define CONFIG_SYS_I2C_MULTI_EEPROMS
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
+
+#define CONFIG_CMD_I2C
+
+
+#define CONFIG_FSL_ESPI
+/* eSPI - Enhanced SPI */
+#ifdef CONFIG_FSL_ESPI
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_SPANSION
+#define CONFIG_CMD_SF
+#define CONFIG_SF_DEFAULT_SPEED 10000000
+#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
+#endif
+
+#if defined(CONFIG_TSEC_ENET)
+
+#define CONFIG_MII /* MII PHY management */
+#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */
+#define CONFIG_TSEC1 1
+#define CONFIG_TSEC1_NAME "eTSEC1"
+#define CONFIG_TSEC2 1
+#define CONFIG_TSEC2_NAME "eTSEC2"
+
+#define TSEC1_PHY_ADDR 0
+#define TSEC2_PHY_ADDR 3
+
+#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
+
+#define TSEC1_PHYIDX 0
+
+#define TSEC2_PHYIDX 0
+
+#define CONFIG_ETHPRIME "eTSEC1"
+
+#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
+
+#endif /* CONFIG_TSEC_ENET */
+
+/*
+ * Environment
+ */
+#if defined(CONFIG_SYS_RAMBOOT)
+#if defined(CONFIG_RAMBOOT_SPIFLASH)
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SPI_BUS 0
+#define CONFIG_ENV_SPI_CS 0
+#define CONFIG_ENV_SPI_MAX_HZ 10000000
+#define CONFIG_ENV_SPI_MODE 0
+#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */
+#define CONFIG_ENV_SECT_SIZE 0x10000
+#define CONFIG_ENV_SIZE 0x2000
+#else
+#define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
+#define CONFIG_ENV_SIZE 0x2000
+#endif
+#else
+#define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
+#define CONFIG_ENV_SIZE 0x400
+#endif
+
+#define CONFIG_LOADS_ECHO /* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ERRATA
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_MII
+#define CONFIG_DOS_PARTITION
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SETEXPR
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_CMDLINE_EDITING /* Command-line editing */
+#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
+#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
+ /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 64 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#endif
+
+#define CONFIG_USB_EHCI
+
+#ifdef CONFIG_USB_EHCI
+#define CONFIG_CMD_USB
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_USB_EHCI_FSL
+#define CONFIG_USB_STORAGE
+#define CONFIG_HAS_FSL_DR_USB
+#endif
+
+/*
+ * Environment Configuration
+ */
+
+#if defined(CONFIG_TSEC_ENET)
+#define CONFIG_HAS_ETH0
+#endif
+
+#define CONFIG_HOSTNAME BSC9131rdb
+#define CONFIG_ROOTPATH "/opt/nfsroot"
+#define CONFIG_BOOTFILE "uImage"
+#define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server */
+
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "uboot=" CONFIG_UBOOTPATH "\0" \
+ "loadaddr=1000000\0" \
+ "bootfile=uImage\0" \
+ "consoledev=ttyS0\0" \
+ "ramdiskaddr=2000000\0" \
+ "ramdiskfile=rootfs.ext2.gz.uboot\0" \
+ "fdtaddr=c00000\0" \
+ "fdtfile=bsc9131rdb.dtb\0" \
+ "bdev=sda1\0" \
+ "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0" \
+ "othbootargs=ramdisk_size=600000 \0" \
+ "usbext2boot=setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs; " \
+ "usb start;" \
+ "ext2load usb 0:4 $loadaddr $bootfile;" \
+ "ext2load usb 0:4 $fdtaddr $fdtfile;" \
+ "ext2load usb 0:4 $ramdiskaddr $ramdiskfile;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr\0" \
+
+#define CONFIG_RAMBOOTCOMMAND \
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs; " \
+ "tftp $ramdiskaddr $ramdiskfile;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND
+
+#endif /* __CONFIG_H */
/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */
-#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
+#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserved for malloc */
/*
* Initial RAM Base Address Setup
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */
-#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
+#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserved for malloc */
/*
* Local Bus LCRR and LBCR regs
/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */
-#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
+#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserved for malloc */
/*
* Local Bus LCRR and LBCR regs
/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */
-#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
+#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserved for malloc */
/*
* Initial RAM Base Address Setup
#endif
#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */
-#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
+#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserved for malloc */
/*
* Initial RAM Base Address Setup
/*
- * Copyright 2007-2009,2010-2011 Freescale Semiconductor, Inc.
+ * Copyright 2007-2009,2010-2012 Freescale Semiconductor, Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
/*
* USB
*/
+#define CONFIG_HAS_FSL_MPH_USB
+#ifdef CONFIG_HAS_FSL_MPH_USB
#define CONFIG_USB_EHCI
#ifdef CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_FSL
#define CONFIG_USB_STORAGE
#endif
+#endif
#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI)
#define CONFIG_CMD_EXT2
/*
- * Copyright 2010-2011 Freescale Semiconductor, Inc.
+ * Copyright 2010-2012 Freescale Semiconductor, Inc.
* Authors: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
* Timur Tabi <timur@freescale.com>
*
/*
* USB
*/
+#define CONFIG_HAS_FSL_DR_USB
+#ifdef CONFIG_HAS_FSL_DR_USB
#define CONFIG_USB_EHCI
#ifdef CONFIG_USB_EHCI
#define CONFIG_USB_STORAGE
#define CONFIG_CMD_FAT
#endif
+#endif
/*
* Miscellaneous configurable options
#define CONFIG_LOADADDR 1000000
#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
-#define CONFIG_BOOTARGS
#define CONFIG_BAUDRATE 115200
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "perf_mode=stable\0" \
- "memctl_intlv_ctl=2\0" \
- "netdev=eth0\0" \
- "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \
- "tftpflash=tftpboot $loadaddr $uboot; " \
- "protect off " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; " \
- "erase " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; " \
- "cp.b $loadaddr " MK_STR(CONFIG_SYS_TEXT_BASE) " $filesize; " \
- "protect on " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; " \
- "cmp.b $loadaddr " MK_STR(CONFIG_SYS_TEXT_BASE) " $filesize\0" \
- "consoledev=ttyS0\0" \
- "ramdiskaddr=2000000\0" \
- "ramdiskfile=uramdisk\0" \
- "fdtaddr=c00000\0" \
- "fdtfile=p1022ds.dtb\0" \
- "bdev=sda3\0" \
- "diuregs=md e002c000 1d\0" \
- "dium=mw e002c01c\0" \
- "diuerr=md e002c014 1\0" \
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \
+ "ubootaddr=" MK_STR(CONFIG_SYS_TEXT_BASE) "\0" \
+ "tftpflash=tftpboot $loadaddr $uboot && " \
+ "protect off $ubootaddr +$filesize && " \
+ "erase $ubootaddr +$filesize && " \
+ "cp.b $loadaddr $ubootaddr $filesize && " \
+ "protect on $ubootaddr +$filesize && " \
+ "cmp.b $loadaddr $ubootaddr $filesize\0" \
+ "consoledev=ttyS0\0" \
+ "ramdiskaddr=2000000\0" \
+ "ramdiskfile=rootfs.ext2.gz.uboot\0" \
+ "fdtaddr=c00000\0" \
+ "fdtfile=p1022ds.dtb\0" \
+ "bdev=sda3\0" \
"hwconfig=esdhc;audclk:12\0"
#define CONFIG_HDBOOT \
"setenv bootargs root=/dev/$bdev rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
+ "console=$consoledev,$baudrate $othbootargs $videobootargs;" \
"tftp $loadaddr $bootfile;" \
"tftp $fdtaddr $fdtfile;" \
"bootm $loadaddr - $fdtaddr"
"setenv bootargs root=/dev/nfs rw " \
"nfsroot=$serverip:$rootpath " \
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
- "console=$consoledev,$baudrate $othbootargs;" \
+ "console=$consoledev,$baudrate $othbootargs $videobootargs;" \
"tftp $loadaddr $bootfile;" \
"tftp $fdtaddr $fdtfile;" \
"bootm $loadaddr - $fdtaddr"
#define CONFIG_RAMBOOTCOMMAND \
"setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
+ "console=$consoledev,$baudrate $othbootargs $videobootargs;" \
"tftp $ramdiskaddr $ramdiskfile;" \
"tftp $loadaddr $bootfile;" \
"tftp $fdtaddr $fdtfile;" \
/*
- * Copyright 2010-2011 Freescale Semiconductor, Inc.
+ * Copyright 2010-2012 Freescale Semiconductor, Inc.
*
* Authors: Roy Zang <tie-fei.zang@freescale.com>
* Chunhe Lan <b25806@freescale.com>
/*
* USB
*/
+#define CONFIG_HAS_FSL_DR_USB
+#ifdef CONFIG_HAS_FSL_DR_USB
#define CONFIG_USB_EHCI
#ifdef CONFIG_USB_EHCI
#define CONFIG_CMD_FAT
#define CONFIG_DOS_PARTITION
#endif
+#endif
/*
* Miscellaneous configurable options
/*
- * Copyright 2009-2010 Freescale Semiconductor, Inc.
+ * Copyright 2009-2010,2012 Freescale Semiconductor, Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
#define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
#endif /* CONFIG_MMC */
+#define CONFIG_HAS_FSL_DR_USB
+#ifdef CONFIG_HAS_FSL_DR_USB
#define CONFIG_USB_EHCI
#ifdef CONFIG_USB_EHCI
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_EHCI_FSL
#define CONFIG_USB_STORAGE
-#define CONFIG_HAS_FSL_DR_USB
+#endif
#endif
#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI)
/*
- * Copyright 2007-2011 Freescale Semiconductor, Inc.
+ * Copyright 2007-2012 Freescale Semiconductor, Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
#else
#define CONFIG_FSL_DDR3 1
#endif
-#undef CONFIG_FSL_DDR_INTERACTIVE
/* ECC will be enabled based on perf_mode environment variable */
/* #define CONFIG_DDR_ECC */
*
*/
-#undef CONFIG_CLOCKS_IN_MHZ
-
/*
* Memory map
*
#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
-#undef CONFIG_SYS_FLASH_CHECKSUM
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
/* I2C */
#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
#define CONFIG_HARD_I2C /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CONFIG_I2C_MULTI_BUS
#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
#define CONFIG_SYS_SRIO2_MEM_SIZE 0x20000000 /* 512M */
#define CONFIG_PCI_PNP /* do pci plug-and-play */
-
-#undef CONFIG_EEPRO100
-#undef CONFIG_TULIP
-#define CONFIG_RTL8139
-
-#ifndef CONFIG_PCI_PNP
- #define PCI_ENET0_IOADDR CONFIG_SYS_PCIE3_IO_BUS
- #define PCI_ENET0_MEMADDR CONFIG_SYS_PCIE3_IO_BUS
- #define PCI_IDSEL_NUMBER 0x11 /* IDSEL = AD11 */
-#endif
-
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#define CONFIG_DOS_PARTITION
#define CONFIG_SCSI_AHCI
#define CONFIG_TSEC3 1
#define CONFIG_TSEC3_NAME "eTSEC3"
-#define CONFIG_PIXIS_SGMII_CMD
#define CONFIG_FSL_SGMII_RISER 1
#define SGMII_RISER_PHY_OFFSET 0x1b
/*
* USB
*/
+#define CONFIG_HAS_FSL_DR_USB
+#ifdef CONFIG_HAS_FSL_DR_USB
#define CONFIG_USB_EHCI
#ifdef CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#endif
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
+#endif
/*
* SDHC/MMC
#define CONFIG_LOADADDR 1000000
#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
-#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
#define CONFIG_BAUDRATE 115200
/*
- * Copyright 2011 Freescale Semiconductor, Inc.
+ * Copyright 2011-2012 Freescale Semiconductor, Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
/*
* USB
*/
+#define CONFIG_HAS_FSL_DR_USB
+#define CONFIG_HAS_FSL_MPH_USB
+
+#if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_MPH_USB)
#define CONFIG_CMD_USB
#define CONFIG_USB_STORAGE
#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#endif
+
#define CONFIG_CMD_EXT2
#define CONFIG_MMC
/*
- * Copyright 2009-2011 Freescale Semiconductor, Inc.
+ * Copyright 2009-2012 Freescale Semiconductor, Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
/*
* USB
*/
+#define CONFIG_HAS_FSL_DR_USB
+#define CONFIG_HAS_FSL_MPH_USB
+
+#if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_MPH_USB)
#define CONFIG_CMD_USB
#define CONFIG_USB_STORAGE
#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_CMD_EXT2
-#define CONFIG_HAS_FSL_DR_USB
+#endif
#ifdef CONFIG_MMC
#define CONFIG_FSL_ESDHC
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
+#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserved for malloc */
/*
* Local Bus LCRR and LBCR regs
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB */
-#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Malloc size */
+#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Malloc size */
/*
* Local Bus LCRR and LBCR regs
return (phys_addr_t)(~0);
}
-unsigned long addrmap_phys_to_virt(phys_addr_t paddr)
+void *addrmap_phys_to_virt(phys_addr_t paddr)
{
int i;
for (i = 0; i < CONFIG_SYS_NUM_ADDR_MAP; i++) {
- u64 base, upper, addr;
+ phys_addr_t base, upper;
if (address_map[i].size == 0)
continue;
- addr = (u64)paddr;
- base = (u64)(address_map[i].paddr);
- upper = (u64)(address_map[i].size) + base - 1;
+ base = address_map[i].paddr;
+ upper = address_map[i].size + base - 1;
- if (addr >= base && addr <= upper) {
- return paddr - address_map[i].paddr + address_map[i].vaddr;
+ if (paddr >= base && paddr <= upper) {
+ phys_addr_t offset;
+
+ offset = address_map[i].paddr - address_map[i].vaddr;
+
+ return (void *)(unsigned long)(paddr - offset);
}
}
- return (unsigned long)(~0);
+ return (void *)(~0);
}
void addrmap_set_entry(unsigned long vaddr, phys_addr_t paddr,
projects / karo-tx-uboot.git / commitdiff