#define CONFIG_SYS_IMMR 0xE0000000
-#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
+#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest region */
#define CONFIG_SYS_MEMTEST_END 0x00100000
#undef CONFIG_DDR_ECC /* only for ECC DDR module */
#undef CONFIG_DDR_ECC_CMD /* use DDR ECC user commands */
#define CONFIG_SPD_EEPROM /* use SPD EEPROM for DDR setup*/
-#define CONFIG_SYS_83XX_DDR_USES_CS0 /* WRS; Fsl board uses CS2/CS3 */
+#define CONFIG_SYS_83XX_DDR_USES_CS0 /* WRS; Fsl board uses CS2/CS3 */
/*
* 32-bit data path mode.
*/
#undef CONFIG_DDR_32BIT
-#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory*/
+#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory*/
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \
* NB: manual DDR setup untested on sbc834x
*/
#define CONFIG_SYS_DDR_SIZE 256 /* MB */
-#define CONFIG_SYS_DDR_CONFIG (CSCONFIG_EN | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10)
+#define CONFIG_SYS_DDR_CONFIG (CSCONFIG_EN \
+ | CSCONFIG_ROW_BIT_13 \
+ | CSCONFIG_COL_BIT_10)
#define CONFIG_SYS_DDR_TIMING_1 0x36332321
#define CONFIG_SYS_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */
-#define CONFIG_SYS_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */
+#define CONFIG_SYS_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */
#define CONFIG_SYS_DDR_INTERVAL 0x04060100 /* autocharge,no open page */
#if defined(CONFIG_DDR_32BIT)
/* set burst length to 8 for 32-bit data path */
-#define CONFIG_SYS_DDR_MODE 0x00000023 /* DLL,normal,seq,4/2.5, 8 burst len */
+ /* DLL,normal,seq,4/2.5, 8 burst len */
+#define CONFIG_SYS_DDR_MODE 0x00000023
#else
/* the default burst length is 4 - for 64-bit data path */
-#define CONFIG_SYS_DDR_MODE 0x00000022 /* DLL,normal,seq,4/2.5, 4 burst len */
+ /* DLL,normal,seq,4/2.5, 4 burst len */
+#define CONFIG_SYS_DDR_MODE 0x00000022
#endif
#endif
* SDRAM on the Local Bus
*/
#define CONFIG_SYS_LBC_SDRAM_BASE 0x10000000 /* Localbus SDRAM */
-#define CONFIG_SYS_LBC_SDRAM_SIZE 128 /* LBC SDRAM is 128MB */
+#define CONFIG_SYS_LBC_SDRAM_SIZE 128 /* LBC SDRAM is 128MB */
/*
* FLASH on the Local Bus
*/
-#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
-#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
+#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
+#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
#define CONFIG_SYS_FLASH_BASE 0xFF800000 /* start of FLASH */
#define CONFIG_SYS_FLASH_SIZE 8 /* flash size in MB */
/* #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE */
-#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | /* flash Base address */ \
- (2 << BR_PS_SHIFT) | /* 16 bit port size */ \
- BR_V) /* valid */
+#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \
+ | (2 << BR_PS_SHIFT) /* 16 bit port */ \
+ | BR_V) /* valid */
#define CONFIG_SYS_OR0_PRELIM 0xFF806FF7 /* 8 MB flash size */
-#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE /* window base at flash base */
+ /* window base at flash base */
+#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_LBLAWAR0_PRELIM 0x80000016 /* 8 MB window size */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 64 /* sectors per device */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 64 /* sectors per device */
#undef CONFIG_SYS_FLASH_CHECKSUM
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#endif
#define CONFIG_SYS_INIT_RAM_LOCK 1
-#define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM*/
+ /* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000
+ /* Size of used area in RAM*/
+#define CONFIG_SYS_INIT_RAM_SIZE 0x1000
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_GBL_DATA_OFFSET \
+ (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
+#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
/*
* Local Bus LCRR and LBCR regs
* FIXME: the top 17 bits of BR2.
*/
-#define CONFIG_SYS_BR2_PRELIM 0xF0001861 /* Port-size=32bit, MSEL=SDRAM */
+ /* Port-size=32bit, MSEL=SDRAM */
+#define CONFIG_SYS_BR2_PRELIM 0xF0001861
#define CONFIG_SYS_LBLAWBAR2_PRELIM 0xF0000000
#define CONFIG_SYS_LBLAWAR2_PRELIM 0x80000019 /* 64M */
#define CONFIG_SYS_OR2_PRELIM 0xFC006901
-#define CONFIG_SYS_LBC_LSRT 0x32000000 /* LB sdram refresh timer, about 6us */
-#define CONFIG_SYS_LBC_MRTPR 0x20000000 /* LB refresh timer prescal, 266MHz/32 */
+ /* LB sdram refresh timer, about 6us */
+#define CONFIG_SYS_LBC_LSRT 0x32000000
+ /* LB refresh timer prescal, 266MHz/32 */
+#define CONFIG_SYS_LBC_MRTPR 0x20000000
-#define CONFIG_SYS_LBC_LSDMR_COMMON ( LSDMR_RFEN \
- | LSDMR_BSMA1516 \
- | LSDMR_RFCR8 \
- | LSDMR_PRETOACT6 \
- | LSDMR_ACTTORW3 \
- | LSDMR_BL8 \
- | LSDMR_WRC3 \
- | LSDMR_CL3 \
- )
+#define CONFIG_SYS_LBC_LSDMR_COMMON (LSDMR_RFEN \
+ | LSDMR_BSMA1516 \
+ | LSDMR_RFCR8 \
+ | LSDMR_PRETOACT6 \
+ | LSDMR_ACTTORW3 \
+ | LSDMR_BL8 \
+ | LSDMR_WRC3 \
+ | LSDMR_CL3)
/*
* SDRAM Controller configuration sequence.
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
/* Use the HUSH parser */
#define CONFIG_SYS_HUSH_PARSER
-#ifdef CONFIG_SYS_HUSH_PARSER
+#ifdef CONFIG_SYS_HUSH_PARSER
#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#endif
#define CONFIG_HARD_I2C /* I2C with hardware support*/
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CONFIG_FSL_I2C
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */
-#define CONFIG_SYS_I2C1_OFFSET 0x3000
-#define CONFIG_SYS_I2C2_OFFSET 0x3100
-#define CONFIG_SYS_I2C_OFFSET CONFIG_SYS_I2C2_OFFSET
+#define CONFIG_SYS_I2C1_OFFSET 0x3000
+#define CONFIG_SYS_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_I2C_OFFSET CONFIG_SYS_I2C2_OFFSET
/* could also use CONFIG_I2C_MULTI_BUS and CONFIG_SYS_SPD_BUS_NUM... */
/* TSEC */
#define CONFIG_SYS_TSEC1_OFFSET 0x24000
-#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
+#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
#define CONFIG_SYS_TSEC2_OFFSET 0x25000
-#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
+#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
/*
* General PCI
#define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000
#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE
#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCI1_IO_BASE 0x00000000
-#define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000
-#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */
+#define CONFIG_SYS_PCI1_IO_BASE 0x00000000
+#define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000
+#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */
#define CONFIG_SYS_PCI2_MEM_BASE 0xA0000000
#define CONFIG_SYS_PCI2_MEM_PHYS CONFIG_SYS_PCI2_MEM_BASE
#define CONFIG_SYS_PCI2_MMIO_BASE 0xB0000000
#define CONFIG_SYS_PCI2_MMIO_PHYS CONFIG_SYS_PCI2_MMIO_BASE
#define CONFIG_SYS_PCI2_MMIO_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCI2_IO_BASE 0x00000000
-#define CONFIG_SYS_PCI2_IO_PHYS 0xE2100000
-#define CONFIG_SYS_PCI2_IO_SIZE 0x00100000 /* 1M */
+#define CONFIG_SYS_PCI2_IO_BASE 0x00000000
+#define CONFIG_SYS_PCI2_IO_PHYS 0xE2100000
+#define CONFIG_SYS_PCI2_IO_SIZE 0x00100000 /* 1M */
#if defined(CONFIG_PCI)
#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
#else
- #define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */
+ #define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */
#define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
- #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+ #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
- #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+ #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
+ /* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+ /* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
/*
* For booting Linux, the board info and command line data
* have to be in the first 256 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux*/
+ /* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTMAPSZ (256 << 20)
#define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST */
HRCWH_SW_WATCHDOG_DISABLE |\
HRCWH_ROM_LOC_LOCAL_16BIT |\
HRCWH_TSEC1M_IN_GMII |\
- HRCWH_TSEC2M_IN_GMII )
+ HRCWH_TSEC2M_IN_GMII)
#else
#define CONFIG_SYS_HRCW_HIGH (\
HRCWH_PCI_HOST |\
HRCWH_SW_WATCHDOG_DISABLE |\
HRCWH_ROM_LOC_LOCAL_16BIT |\
HRCWH_TSEC1M_IN_GMII |\
- HRCWH_TSEC2M_IN_GMII )
+ HRCWH_TSEC2M_IN_GMII)
#endif
/* System IO Config */
#define CONFIG_SYS_SICRL SICRL_LDP_A
#define CONFIG_SYS_HID0_INIT 0x000000000
-#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \
- HID0_ENABLE_INSTRUCTION_CACHE)
+#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK \
+ | HID0_ENABLE_INSTRUCTION_CACHE)
-/* #define CONFIG_SYS_HID0_FINAL (\
+/* #define CONFIG_SYS_HID0_FINAL (\
HID0_ENABLE_INSTRUCTION_CACHE |\
HID0_ENABLE_M_BIT |\
- HID0_ENABLE_ADDRESS_BROADCAST ) */
+ HID0_ENABLE_ADDRESS_BROADCAST) */
#define CONFIG_SYS_HID2 HID2_HBE
#define CONFIG_HIGH_BATS 1 /* High BATs supported */
/* DDR @ 0x00000000 */
-#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE \
+ | BATL_PP_10 \
+ | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \
+ | BATU_BL_256M \
+ | BATU_VS \
+ | BATU_VP)
/* PCI @ 0x80000000 */
#ifdef CONFIG_PCI
-#define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT1U (CONFIG_SYS_PCI1_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI1_MMIO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT2U (CONFIG_SYS_PCI1_MMIO_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_BASE \
+ | BATL_PP_10 \
+ | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT1U (CONFIG_SYS_PCI1_MEM_BASE \
+ | BATU_BL_256M \
+ | BATU_VS \
+ | BATU_VP)
+#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI1_MMIO_BASE \
+ | BATL_PP_10 \
+ | BATL_CACHEINHIBIT \
+ | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT2U (CONFIG_SYS_PCI1_MMIO_BASE \
+ | BATU_BL_256M \
+ | BATU_VS \
+ | BATU_VP)
#else
#define CONFIG_SYS_IBAT1L (0)
#define CONFIG_SYS_IBAT1U (0)
#endif
#ifdef CONFIG_MPC83XX_PCI2
-#define CONFIG_SYS_IBAT3L (CONFIG_SYS_PCI2_MEM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT3U (CONFIG_SYS_PCI2_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCI2_MMIO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT4U (CONFIG_SYS_PCI2_MMIO_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT3L (CONFIG_SYS_PCI2_MEM_BASE \
+ | BATL_PP_10 \
+ | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT3U (CONFIG_SYS_PCI2_MEM_BASE \
+ | BATU_BL_256M \
+ | BATU_VS \
+ | BATU_VP)
+#define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCI2_MMIO_BASE \
+ | BATL_PP_10 \
+ | BATL_CACHEINHIBIT \
+ | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT4U (CONFIG_SYS_PCI2_MMIO_BASE \
+ | BATU_BL_256M \
+ | BATU_VS \
+ | BATU_VP)
#else
#define CONFIG_SYS_IBAT3L (0)
#define CONFIG_SYS_IBAT3U (0)
#endif
/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 */
-#define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR \
+ | BATL_PP_10 \
+ | BATL_CACHEINHIBIT \
+ | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR \
+ | BATU_BL_256M \
+ | BATU_VS \
+ | BATU_VP)
/* SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */
-#define CONFIG_SYS_IBAT6L (0xF0000000 | BATL_PP_10 | BATL_MEMCOHERENCE | \
- BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT6L (0xF0000000 \
+ | BATL_PP_10 \
+ | BATL_MEMCOHERENCE \
+ | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT6U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
#define CONFIG_SYS_IBAT7L (0)
#define CONFIG_ROOTPATH "/tftpboot/rootfs"
#define CONFIG_BOOTFILE "uImage"
-#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
+ /* default location for tftp and bootm */
+#define CONFIG_LOADADDR 800000
#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
-#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
+#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
#define CONFIG_BAUDRATE 115200
"bootm\0" \
"load=tftp 100000 /tftpboot/sbc8349/u-boot.bin\0" \
"update=protect off ff800000 ff83ffff; " \
- "era ff800000 ff83ffff; cp.b 100000 ff800000 ${filesize}\0" \
+ "era ff800000 ff83ffff; cp.b 100000 ff800000 ${filesize}\0" \
"upd=run load update\0" \
"fdtaddr=780000\0" \
"fdtfile=sbc8349.dtb\0" \
""
-#define CONFIG_NFSBOOTCOMMAND \
- "setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$serverip:$rootpath " \
- "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr - $fdtaddr"
+#define CONFIG_NFSBOOTCOMMAND \
+ "setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$serverip:$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \
+ "$netdev:off " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
#define CONFIG_RAMBOOTCOMMAND \
- "setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $ramdiskaddr $ramdiskfile;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr $ramdiskaddr $fdtaddr"
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $ramdiskaddr $ramdiskfile;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
#define CONFIG_BOOTCOMMAND "run flash_self"
projects / karo-tx-uboot.git / commitdiff