config TARGET_NHK8815
bool "Support nhk8815"
-config TARGET_OMAP5912OSK
- bool "Support omap5912osk"
-
config TARGET_EDMINIV2
bool "Support edminiv2"
source "board/ti/dra7xx/Kconfig"
source "board/ti/evm/Kconfig"
source "board/ti/ks2_evm/Kconfig"
-source "board/ti/omap5912osk/Kconfig"
source "board/ti/omap5_uevm/Kconfig"
source "board/ti/panda/Kconfig"
source "board/ti/sdp3430/Kconfig"
+++ /dev/null
-if TARGET_OMAP5912OSK
-
-config SYS_CPU
- string
- default "arm926ejs"
-
-config SYS_BOARD
- string
- default "omap5912osk"
-
-config SYS_VENDOR
- string
- default "ti"
-
-config SYS_SOC
- string
- default "omap"
-
-config SYS_CONFIG_NAME
- string
- default "omap5912osk"
-
-endif
+++ /dev/null
-OMAP5912OSK BOARD
-M: Rishi Bhattacharya <rishi@ti.com>
-S: Maintained
-F: board/ti/omap5912osk/
-F: include/configs/omap5912osk.h
-F: configs/omap5912osk_defconfig
+++ /dev/null
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y := omap5912osk.o
-obj-y += lowlevel_init.o
+++ /dev/null
-#
-# (C) Copyright 2002-2004
-# Gary Jennejohn, DENX Software Engineering, <garyj@denx.de>
-# David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
-#
-# (C) Copyright 2003
-# Texas Instruments, <www.ti.com>
-# Kshitij Gupta <Kshitij@ti.com>
-#
-# (C) Copyright 2004
-# Texas Instruments, <www.ti.com>
-# Rishi Bhattacharya <rishi@ti.com>
-#
-# TI OSK board with OMAP5912 (ARM925EJS) cpu
-# see http://www.ti.com/ for more information on Texas Instruments
-#
-# OSK has 1 bank of 32 MB SDRAM
-# Physical Address:
-# 1000'0000 to 1200'0000
-#
-#
-# Linux-Kernel is expected to be at 1000'8000, entry 1000'8000
-# (mem base + reserved)
-#
-# When running from RAM use address 1108'0000, otherwise when
-# booting from NOR flash link to address 0000'0000.
-#
-
-CONFIG_SYS_TEXT_BASE = 0x00000000
-#CONFIG_SYS_TEXT_BASE = 0x11080000
+++ /dev/null
-/*
- * Board specific setup info
- *
- * (C) Copyright 2003
- * Texas Instruments, <www.ti.com>
- * Kshitij Gupta <Kshitij@ti.com>
- *
- * Modified for OMAP 1610 H2 board by Nishant Kamat, Jan 2004
- *
- * Modified for OMAP 5912 OSK board by Rishi Bhattacharya, Apr 2004
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <config.h>
-#include <version.h>
-
-#if defined(CONFIG_OMAP1610)
-#include <./configs/omap1510.h>
-#endif
-
-.globl lowlevel_init
-lowlevel_init:
-
- /*------------------------------------------------------*
- * Ensure i-cache is enabled *
- * To configure TC regs without fetching instruction *
- *------------------------------------------------------*/
- mrc p15, 0, r0, c1, c0
- orr r0, r0, #0x1000
- mcr p15, 0, r0, c1, c0
-
- /*------------------------------------------------------*
- *mask all IRQs by setting all bits in the INTMR default*
- *------------------------------------------------------*/
- mov r1, #0xffffffff
- ldr r0, =REG_IHL1_MIR
- str r1, [r0]
- ldr r0, =REG_IHL2_MIR
- str r1, [r0]
-
- /*------------------------------------------------------*
- * Set up ARM CLM registers (IDLECT1) *
- *------------------------------------------------------*/
- ldr r0, REG_ARM_IDLECT1
- ldr r1, VAL_ARM_IDLECT1
- str r1, [r0]
-
- /*------------------------------------------------------*
- * Set up ARM CLM registers (IDLECT2) *
- *------------------------------------------------------*/
- ldr r0, REG_ARM_IDLECT2
- ldr r1, VAL_ARM_IDLECT2
- str r1, [r0]
-
- /*------------------------------------------------------*
- * Set up ARM CLM registers (IDLECT3) *
- *------------------------------------------------------*/
- ldr r0, REG_ARM_IDLECT3
- ldr r1, VAL_ARM_IDLECT3
- str r1, [r0]
-
- mov r1, #0x01 /* PER_EN bit */
- ldr r0, REG_ARM_RSTCT2
- strh r1, [r0] /* CLKM; Peripheral reset. */
-
- /* Set CLKM to Sync-Scalable */
- mov r1, #0x1000
- ldr r0, REG_ARM_SYSST
-
- mov r2, #0
-1: cmp r2, #1
- streqh r1, [r0]
- add r2, r2, #1
- cmp r2, #0x100 /* wait for any bubbles to finish */
- bne 1b
-
- ldr r1, VAL_ARM_CKCTL
- ldr r0, REG_ARM_CKCTL
- strh r1, [r0]
-
- /* a few nops to let settle */
- nop
- nop
- nop
- nop
- nop
- nop
- nop
- nop
- nop
- nop
-
- /* setup DPLL 1 */
- /* Ramp up the clock to 96Mhz */
- ldr r1, VAL_DPLL1_CTL
- ldr r0, REG_DPLL1_CTL
- strh r1, [r0]
- ands r1, r1, #0x10 /* Check if PLL is enabled. */
- beq lock_end /* Do not look for lock if BYPASS selected */
-2:
- ldrh r1, [r0]
- ands r1, r1, #0x01 /* Check the LOCK bit.*/
- beq 2b /* loop until bit goes hi. */
-lock_end:
-
- /*------------------------------------------------------*
- * Turn off the watchdog during init... *
- *------------------------------------------------------*/
- ldr r0, REG_WATCHDOG
- ldr r1, WATCHDOG_VAL1
- str r1, [r0]
- ldr r1, WATCHDOG_VAL2
- str r1, [r0]
- ldr r0, REG_WSPRDOG
- ldr r1, WSPRDOG_VAL1
- str r1, [r0]
- ldr r0, REG_WWPSDOG
-
-watch1Wait:
- ldr r1, [r0]
- tst r1, #0x10
- bne watch1Wait
-
- ldr r0, REG_WSPRDOG
- ldr r1, WSPRDOG_VAL2
- str r1, [r0]
- ldr r0, REG_WWPSDOG
-watch2Wait:
- ldr r1, [r0]
- tst r1, #0x10
- bne watch2Wait
-
- /* Set memory timings corresponding to the new clock speed */
- ldr r3, VAL_SDRAM_CONFIG_SDF0
-
- /* Check execution location to determine current execution location
- * and branch to appropriate initialization code.
- */
- mov r0, #0x10000000 /* Load physical SDRAM base. */
- mov r1, pc /* Get current execution location. */
- cmp r1, r0 /* Compare. */
- bge skip_sdram /* Skip over EMIF-fast initialization if running from SDRAM. */
-
- /* identify the device revision, -- TMX or TMP(TMS) */
- ldr r0, REG_DEVICE_ID
- ldr r1, [r0]
-
- ldr r0, VAL_DEVICE_ID_TMP
- mov r1, r1, lsl #15
- mov r1, r1, lsr #16
- cmp r0, r1
- bne skip_TMP_Patch
-
- /* Enable TMP/TMS device new features */
- mov r0, #1
- ldr r1, REG_TC_EMIFF_DOUBLER
- str r0, [r1]
-
- /* Enable new ac parameters */
- mov r0, #0x0b
- ldr r1, REG_SDRAM_CONFIG2
- str r0, [r1]
-
- ldr r3, VAL_SDRAM_CONFIG_SDF1
-
-skip_TMP_Patch:
-
- /*
- * Delay for SDRAM initialization.
- */
- mov r0, #0x1800 /* value should be checked */
-3:
- subs r0, r0, #0x1 /* Decrement count */
- bne 3b
-
- /*
- * Set SDRAM control values. Disable refresh before MRS command.
- */
-
- /* mobile ddr operation */
- ldr r0, REG_SDRAM_OPERATION
- mov r2, #07
- str r2, [r0]
-
- /* config register */
- ldr r0, REG_SDRAM_CONFIG
- str r3, [r0]
-
- /* manual command register */
- ldr r0, REG_SDRAM_MANUAL_CMD
-
- /* issue set cke high */
- mov r1, #CMD_SDRAM_CKE_SET_HIGH
- str r1, [r0]
-
- /* issue nop */
- mov r1, #CMD_SDRAM_NOP
- str r1, [r0]
-
- mov r2, #0x0100
-waitMDDR1:
- subs r2, r2, #1
- bne waitMDDR1 /* delay loop */
-
- /* issue precharge */
- mov r1, #CMD_SDRAM_PRECHARGE
- str r1, [r0]
-
- /* issue autorefresh x 2 */
- mov r1, #CMD_SDRAM_AUTOREFRESH
- str r1, [r0]
- str r1, [r0]
-
- /* mrs register ddr mobile */
- ldr r0, REG_SDRAM_MRS
- mov r1, #0x33
- str r1, [r0]
-
- /* emrs1 low-power register */
- ldr r0, REG_SDRAM_EMRS1
- /* self refresh on all banks */
- mov r1, #0
- str r1, [r0]
-
- ldr r0, REG_DLL_URD_CONTROL
- ldr r1, DLL_URD_CONTROL_VAL
- str r1, [r0]
-
- ldr r0, REG_DLL_LRD_CONTROL
- ldr r1, DLL_LRD_CONTROL_VAL
- str r1, [r0]
-
- ldr r0, REG_DLL_WRT_CONTROL
- ldr r1, DLL_WRT_CONTROL_VAL
- str r1, [r0]
-
- /* delay loop */
- mov r0, #0x0100
-waitMDDR2:
- subs r0, r0, #1
- bne waitMDDR2
-
- /*
- * Delay for SDRAM initialization.
- */
- mov r0, #0x1800
-4:
- subs r0, r0, #1 /* Decrement count. */
- bne 4b
- b common_tc
-
-skip_sdram:
- ldr r0, REG_SDRAM_CONFIG
- str r3, [r0]
-
-common_tc:
- /* slow interface */
- ldr r1, VAL_TC_EMIFS_CS0_CONFIG
- ldr r0, REG_TC_EMIFS_CS0_CONFIG
- str r1, [r0] /* Chip Select 0 */
-
- ldr r1, VAL_TC_EMIFS_CS1_CONFIG
- ldr r0, REG_TC_EMIFS_CS1_CONFIG
- str r1, [r0] /* Chip Select 1 */
-
- ldr r1, VAL_TC_EMIFS_CS3_CONFIG
- ldr r0, REG_TC_EMIFS_CS3_CONFIG
- str r1, [r0] /* Chip Select 3 */
-
- ldr r1, VAL_TC_EMIFS_DWS
- ldr r0, REG_TC_EMIFS_DWS
- str r1, [r0] /* Enable EMIFS.RDY for CS1 (ether) */
-
-#ifdef CONFIG_H2_OMAP1610
- /* inserting additional 2 clock cycle hold time for LAN */
- ldr r0, REG_TC_EMIFS_CS1_ADVANCED
- ldr r1, VAL_TC_EMIFS_CS1_ADVANCED
- str r1, [r0]
-#endif
- /* Start MPU Timer 1 */
- ldr r0, REG_MPU_LOAD_TIMER
- ldr r1, VAL_MPU_LOAD_TIMER
- str r1, [r0]
-
- ldr r0, REG_MPU_CNTL_TIMER
- ldr r1, VAL_MPU_CNTL_TIMER
- str r1, [r0]
-
- /*
- * Setup a temporary stack
- */
- ldr sp, SRAM_STACK
- bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
-
- /*
- * Save the old lr(passed in ip) and the current lr to stack
- */
- push {ip, lr}
-
- /*
- * go setup pll, mux, memory
- */
- bl s_init
- pop {ip, pc}
-
- /* back to arch calling code */
- mov pc, lr
-
- /* the literal pools origin */
- .ltorg
-
-REG_DEVICE_ID: /* 32 bits */
- .word 0xfffe2004
-REG_TC_EMIFS_CONFIG:
- .word 0xfffecc0c
-REG_TC_EMIFS_CS0_CONFIG: /* 32 bits */
- .word 0xfffecc10
-REG_TC_EMIFS_CS1_CONFIG: /* 32 bits */
- .word 0xfffecc14
-REG_TC_EMIFS_CS2_CONFIG: /* 32 bits */
- .word 0xfffecc18
-REG_TC_EMIFS_CS3_CONFIG: /* 32 bits */
- .word 0xfffecc1c
-REG_TC_EMIFS_DWS: /* 32 bits */
- .word 0xfffecc40
-#ifdef CONFIG_H2_OMAP1610
-REG_TC_EMIFS_CS1_ADVANCED: /* 32 bits */
- .word 0xfffecc54
-#endif
-
-/* MPU clock/reset/power mode control registers */
-REG_ARM_CKCTL: /* 16 bits */
- .word 0xfffece00
-REG_ARM_IDLECT3: /* 16 bits */
- .word 0xfffece24
-REG_ARM_IDLECT2: /* 16 bits */
- .word 0xfffece08
-REG_ARM_IDLECT1: /* 16 bits */
- .word 0xfffece04
-REG_ARM_RSTCT2: /* 16 bits */
- .word 0xfffece14
-REG_ARM_SYSST: /* 16 bits */
- .word 0xfffece18
-
-/* DPLL control registers */
-REG_DPLL1_CTL: /* 16 bits */
- .word 0xfffecf00
-
-/* Watch Dog register */
-/* secure watchdog stop */
-REG_WSPRDOG:
- .word 0xfffeb048
-/* watchdog write pending */
-REG_WWPSDOG:
- .word 0xfffeb034
-
-WSPRDOG_VAL1:
- .word 0x0000aaaa
-WSPRDOG_VAL2:
- .word 0x00005555
-
-/* SDRAM config is: auto refresh enabled, 16 bit 4 bank,
- counter @8192 rows, 10 ns, 8 burst */
-REG_SDRAM_CONFIG:
- .word 0xfffecc20
-REG_SDRAM_CONFIG2:
- .word 0xfffecc3c
-REG_TC_EMIFF_DOUBLER: /* 32 bits */
- .word 0xfffecc60
-
-/* Operation register */
-REG_SDRAM_OPERATION:
- .word 0xfffecc80
-
-/* Manual command register */
-REG_SDRAM_MANUAL_CMD:
- .word 0xfffecc84
-
-/* SDRAM MRS (New) config is: CAS latency is 2, burst length 8 */
-REG_SDRAM_MRS:
- .word 0xfffecc70
-
-/* SDRAM MRS (New) config is: CAS latency is 2, burst length 8 */
-REG_SDRAM_EMRS1:
- .word 0xfffecc78
-
-/* WRT DLL register */
-REG_DLL_WRT_CONTROL:
- .word 0xfffecc68
-DLL_WRT_CONTROL_VAL:
- .word 0x03f00002 /* Phase of 72deg, write offset +31 */
-
-/* URD DLL register */
-REG_DLL_URD_CONTROL:
- .word 0xfffeccc0
-DLL_URD_CONTROL_VAL:
- .word 0x00800002 /* Phase of 72deg, read offset +31 */
-
-/* LRD DLL register */
-REG_DLL_LRD_CONTROL:
- .word 0xfffecccc
-DLL_LRD_CONTROL_VAL:
- .word 0x00800002 /* read offset +31 */
-
-REG_WATCHDOG:
- .word 0xfffec808
-WATCHDOG_VAL1:
- .word 0x000000f5
-WATCHDOG_VAL2:
- .word 0x000000a0
-
-REG_MPU_LOAD_TIMER:
- .word 0xfffec504
-REG_MPU_CNTL_TIMER:
- .word 0xfffec500
-VAL_MPU_LOAD_TIMER:
- .word 0xffffffff
-VAL_MPU_CNTL_TIMER:
- .word 0xffffffa1
-
-/* 96 MHz Samsung Mobile DDR */
-/* Original setting for TMX device */
-VAL_SDRAM_CONFIG_SDF0:
- .word 0x0014e6fe
-
-/* NEW_SYS_FREQ mode (valid only TMP/TMS devices) */
-VAL_SDRAM_CONFIG_SDF1:
- .word 0x0114e6fe
-
-VAL_ARM_CKCTL:
- .word 0x2000 /* was: 0x3000, now use CLK_REF for timer input */
-VAL_DPLL1_CTL:
- .word 0x2830
-
-#ifdef CONFIG_OSK_OMAP5912
-VAL_TC_EMIFS_CS0_CONFIG:
- .word 0x002130b0
-VAL_TC_EMIFS_CS1_CONFIG:
- .word 0x00001133
-VAL_TC_EMIFS_CS2_CONFIG:
- .word 0x000055f0
-VAL_TC_EMIFS_CS3_CONFIG:
- .word 0x88013141
-VAL_TC_EMIFS_DWS: /* Enable EMIFS.RDY for CS1 access (ether) */
- .word 0x000000c0
-VAL_DEVICE_ID_TMP: /* TMP/TMS=0xb65f, TMX=0xb58c */
- .word 0xb65f
-#endif
-
-#ifdef CONFIG_H2_OMAP1610
-VAL_TC_EMIFS_CS0_CONFIG:
- .word 0x00203331
-VAL_TC_EMIFS_CS1_CONFIG:
- .word 0x8180fff3
-VAL_TC_EMIFS_CS2_CONFIG:
- .word 0xf800f22a
-VAL_TC_EMIFS_CS3_CONFIG:
- .word 0x88013141
-VAL_TC_EMIFS_CS1_ADVANCED:
- .word 0x00000022
-#endif
-
-VAL_ARM_IDLECT1:
- .word 0x00000400
-VAL_ARM_IDLECT2:
- .word 0x00000886
-VAL_ARM_IDLECT3:
- .word 0x00000015
-
-SRAM_STACK:
- .word CONFIG_SYS_INIT_SP_ADDR
-
-/* command values */
-.equ CMD_SDRAM_NOP, 0x00000000
-.equ CMD_SDRAM_PRECHARGE, 0x00000001
-.equ CMD_SDRAM_AUTOREFRESH, 0x00000002
-.equ CMD_SDRAM_CKE_SET_HIGH, 0x00000007
+++ /dev/null
-/*
- * (C) Copyright 2002
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- *
- * (C) Copyright 2002
- * David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
- *
- * (C) Copyright 2003
- * Texas Instruments, <www.ti.com>
- * Kshitij Gupta <Kshitij@ti.com>
- *
- * (C) Copyright 2004
- * Texas Instruments, <www.ti.com>
- * Rishi Bhattacharya <rishi@ti.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <netdev.h>
-#if defined(CONFIG_OMAP1610)
-#include <./configs/omap1510.h>
-#endif
-
-DECLARE_GLOBAL_DATA_PTR;
-
-void flash__init (void);
-void ether__init (void);
-void set_muxconf_regs (void);
-void peripheral_power_enable (void);
-
-#define COMP_MODE_ENABLE ((unsigned int)0x0000EAEF)
-
-static inline void delay (unsigned long loops)
-{
- __asm__ volatile ("1:\n"
- "subs %0, %1, #1\n"
- "bne 1b":"=r" (loops):"0" (loops));
-}
-
-/*
- * Miscellaneous platform dependent initialisations
- */
-
-int board_init (void)
-{
- gd->bd->bi_arch_number = MACH_TYPE_OMAP_OSK;
-
- /* adress of boot parameters */
- gd->bd->bi_boot_params = 0x10000100;
-
- flash__init();
- ether__init();
-
- return 0;
-}
-
-void s_init(void)
-{
- /* Configure MUX settings */
- set_muxconf_regs ();
- peripheral_power_enable ();
-
-/* this speeds up your boot a quite a bit. However to make it
- * work, you need make sure your kernel startup flush bug is fixed.
- * ... rkw ...
- */
- icache_enable ();
-}
-
-/******************************
- Routine:
- Description:
-******************************/
-void flash__init (void)
-{
-#define EMIFS_GlB_Config_REG 0xfffecc0c
- unsigned int regval;
- regval = *((volatile unsigned int *) EMIFS_GlB_Config_REG);
- /* Turn off write protection for flash devices. */
- regval = regval | 0x0001;
- *((volatile unsigned int *) EMIFS_GlB_Config_REG) = regval;
-}
-/*************************************************************
- Routine:ether__init
- Description: take the Ethernet controller out of reset and wait
- for the EEPROM load to complete.
-*************************************************************/
-void ether__init (void)
-{
-#define ETH_CONTROL_REG 0x0480000b
- int i;
-
- *((volatile unsigned short *) 0xfffece08) = 0x03FF;
- *((volatile unsigned short *) 0xfffb3824) = 0x8000;
- *((volatile unsigned short *) 0xfffb3830) = 0x0000;
- *((volatile unsigned short *) 0xfffb3834) = 0x0009;
- *((volatile unsigned short *) 0xfffb3838) = 0x0009;
- *((volatile unsigned short *) 0xfffb3818) = 0x0002;
- *((volatile unsigned short *) 0xfffb382C) = 0x0048;
- *((volatile unsigned short *) 0xfffb3824) = 0x8603;
- udelay (3);
- for (i=0;i<2000;i++);
- *((volatile unsigned short *) 0xfffb381C) = 0x6610;
- udelay (30);
- for (i=0;i<10000;i++);
-
- *((volatile unsigned char *) ETH_CONTROL_REG) &= ~0x01;
- udelay (3);
-
-
-}
-
-/******************************
- Routine:
- Description:
-******************************/
-int dram_init(void)
-{
- gd->ram_size = get_ram_size((long *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE);
-
- return 0;
-}
-
-void dram_init_banksize(void)
-{
- gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
- gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
-}
-
-/******************************************************
- Routine: set_muxconf_regs
- Description: Setting up the configuration Mux registers
- specific to the hardware
-*******************************************************/
-void set_muxconf_regs (void)
-{
- volatile unsigned int *MuxConfReg;
- /* set each registers to its reset value; */
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_0);
- /* setup for UART1 */
- *MuxConfReg &= ~(0x02000000); /* bit 25 */
- /* setup for UART2 */
- *MuxConfReg &= ~(0x01000000); /* bit 24 */
- /* Disable Uwire CS Hi-Z */
- *MuxConfReg |= 0x08000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_3);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_4);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_5);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_6);
- /*setup mux for UART3 */
- *MuxConfReg |= 0x00000001; /* bit3, 1, 0 (mux0 5,5,26) */
- *MuxConfReg &= ~0x0000003e;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_7);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_8);
- /* Disable Uwire CS Hi-Z */
- *MuxConfReg |= 0x00001200; /*bit 9 for CS0 12 for CS3 */
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_9);
- /* Need to turn on bits 21 and 12 in FUNC_MUX_CTRL_9 so the */
- /* hardware will actually use TX and RTS based on bit 25 in */
- /* FUNC_MUX_CTRL_0. I told you this thing was screwy! */
- *MuxConfReg |= 0x00201000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_A);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_B);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_C);
- /* setup for UART2 */
- /* Need to turn on bits 27 and 24 in FUNC_MUX_CTRL_C so the */
- /* hardware will actually use TX and RTS based on bit 24 in */
- /* FUNC_MUX_CTRL_0. */
- *MuxConfReg |= 0x09000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_D);
- *MuxConfReg |= 0x00000020;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_0);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_1);
- *MuxConfReg = 0x00000000;
- /* mux setup for SD/MMC driver */
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_2);
- *MuxConfReg &= 0xFFFE0FFF;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_3);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) MOD_CONF_CTRL_0);
- /* bit 13 for MMC2 XOR_CLK */
- *MuxConfReg &= ~(0x00002000);
- /* bit 29 for UART 1 */
- *MuxConfReg &= ~(0x00002000);
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_0);
- /* Configure for USB. Turn on VBUS_CTRL and VBUS_MODE. */
- *MuxConfReg |= 0x000C0000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int)USB_TRANSCEIVER_CTRL);
- *MuxConfReg &= ~(0x00000070);
- *MuxConfReg &= ~(0x00000008);
- *MuxConfReg |= 0x00000003;
- *MuxConfReg |= 0x00000180;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) MOD_CONF_CTRL_0);
- /* bit 17, software controls VBUS */
- *MuxConfReg &= ~(0x00020000);
- /* Enable USB 48 and 12M clocks */
- *MuxConfReg |= 0x00000200;
- *MuxConfReg &= ~(0x00000180);
- /*2.75V for MMCSDIO1 */
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) VOLTAGE_CTRL_0);
- *MuxConfReg = 0x00001FE7;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) PU_PD_SEL_0);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) PU_PD_SEL_1);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) PU_PD_SEL_2);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) PU_PD_SEL_3);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) PU_PD_SEL_4);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_4);
- *MuxConfReg = 0x00000000;
- /* Turn on UART2 48 MHZ clock */
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) MOD_CONF_CTRL_0);
- *MuxConfReg |= 0x40000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) USB_OTG_CTRL);
- /* setup for USB VBus detection OMAP161x */
- *MuxConfReg |= 0x00040000; /* bit 18 */
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) PU_PD_SEL_2);
- /* PullUps for SD/MMC driver */
- *MuxConfReg |= ~(0xFFFE0FFF);
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int)COMP_MODE_CTRL_0);
- *MuxConfReg = COMP_MODE_ENABLE;
-}
-
-/******************************************************
- Routine: peripheral_power_enable
- Description: Enable the power for UART1
-*******************************************************/
-void peripheral_power_enable (void)
-{
-#define UART1_48MHZ_ENABLE ((unsigned short)0x0200)
-#define SW_CLOCK_REQUEST ((volatile unsigned short *)0xFFFE0834)
-
- *SW_CLOCK_REQUEST |= UART1_48MHZ_ENABLE;
-}
-
-/*
- * Check Board Identity
- */
-int checkboard(void)
-{
- char buf[64];
- int i = getenv_f("serial#", buf, sizeof(buf));
-
- puts("Board: OSK5912");
-
- if (i > 0) {
- puts(", serial# ");
- puts(buf);
- }
- putc('\n');
-
- return (0);
-}
-
-#ifdef CONFIG_CMD_NET
-int board_eth_init(bd_t *bis)
-{
- int rc = 0;
-#ifdef CONFIG_LAN91C96
- rc = lan91c96_initialize(0, CONFIG_LAN91C96_BASE);
-#endif
- return rc;
-}
-#endif
+++ /dev/null
-CONFIG_ARM=y
-CONFIG_TARGET_OMAP5912OSK=y
Board Arch CPU Commit Removed Last known maintainer/contact
=================================================================================================
+omap5912osk arm arm926ejs - - Rishi Bhattacharya <rishi@ti.com>
p1023rds powerpc mpc85xx d0bc5140 2014-07-22 Roy Zang <tie-fei.zang@freescale.com>
spc1920 powerpc mpc8xx 98ad54be 2014-07-07
v37 powerpc mpc8xx b8c1438a 2014-07-07
obj-y += core.o
obj-y += ep0.o
obj-$(CONFIG_DW_UDC) += designware_udc.o
-obj-$(CONFIG_OMAP1610) += omap1510_udc.o
obj-$(CONFIG_MPC885_FAMILY) += mpc8xx_udc.o
obj-$(CONFIG_CPU_PXA27X) += pxa27x_udc.o
endif
+++ /dev/null
-/*
- * (C) Copyright 2003
- * Gerry Hamel, geh@ti.com, Texas Instruments
- *
- * Based on
- * linux/drivers/usb/device/bi/omap.c
- * TI OMAP1510 USB bus interface driver
- *
- * Author: MontaVista Software, Inc.
- * source@mvista.com
- * (C) Copyright 2002
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/io.h>
-#include <usbdevice.h>
-#include <usb/omap1510_udc.h>
-#include <usb/udc.h>
-
-#include "ep0.h"
-
-
-#define UDC_INIT_MDELAY 80 /* Device settle delay */
-#define UDC_MAX_ENDPOINTS 31 /* Number of endpoints on this UDC */
-
-/* Some kind of debugging output... */
-#if 1
-#define UDCDBG(str)
-#define UDCDBGA(fmt,args...)
-#else /* The bugs still exists... */
-#define UDCDBG(str) serial_printf("[%s] %s:%d: " str "\n", __FILE__,__FUNCTION__,__LINE__)
-#define UDCDBGA(fmt,args...) serial_printf("[%s] %s:%d: " fmt "\n", __FILE__,__FUNCTION__,__LINE__, ##args)
-#endif
-
-#if 1
-#define UDCREG(name)
-#define UDCREGL(name)
-#else /* The bugs still exists... */
-#define UDCREG(name) serial_printf("%s():%d: %s[%08x]=%.4x\n",__FUNCTION__,__LINE__, (#name), name, inw(name)) /* For 16-bit regs */
-#define UDCREGL(name) serial_printf("%s():%d: %s[%08x]=%.8x\n",__FUNCTION__,__LINE__, (#name), name, inl(name)) /* For 32-bit regs */
-#endif
-
-
-static struct urb *ep0_urb = NULL;
-
-static struct usb_device_instance *udc_device; /* Used in interrupt handler */
-static u16 udc_devstat = 0; /* UDC status (DEVSTAT) */
-static u32 udc_interrupts = 0;
-
-static void udc_stall_ep (unsigned int ep_addr);
-
-
-static struct usb_endpoint_instance *omap1510_find_ep (int ep)
-{
- int i;
-
- for (i = 0; i < udc_device->bus->max_endpoints; i++) {
- if (udc_device->bus->endpoint_array[i].endpoint_address == ep)
- return &udc_device->bus->endpoint_array[i];
- }
- return NULL;
-}
-
-/* ************************************************************************** */
-/* IO
- */
-
-/*
- * omap1510_prepare_endpoint_for_rx
- *
- * This function implements TRM Figure 14-11.
- *
- * The endpoint to prepare for transfer is specified as a physical endpoint
- * number. For OUT (rx) endpoints 1 through 15, the corresponding endpoint
- * configuration register is checked to see if the endpoint is ISO or not.
- * If the OUT endpoint is valid and is non-ISO then its FIFO is enabled.
- * No action is taken for endpoint 0 or for IN (tx) endpoints 16 through 30.
- */
-static void omap1510_prepare_endpoint_for_rx (int ep_addr)
-{
- int ep_num = ep_addr & USB_ENDPOINT_NUMBER_MASK;
-
- UDCDBGA ("omap1510_prepare_endpoint %x", ep_addr);
- if (((ep_addr & USB_ENDPOINT_DIR_MASK) == USB_DIR_OUT)) {
- if ((inw (UDC_EP_RX (ep_num)) &
- (UDC_EPn_RX_Valid | UDC_EPn_RX_Iso)) ==
- UDC_EPn_RX_Valid) {
- /* rx endpoint is valid, non-ISO, so enable its FIFO */
- outw (UDC_EP_Sel | ep_num, UDC_EP_NUM);
- outw (UDC_Set_FIFO_En, UDC_CTRL);
- outw (0, UDC_EP_NUM);
- }
- }
-}
-
-/* omap1510_configure_endpoints
- *
- * This function implements TRM Figure 14-10.
- */
-static void omap1510_configure_endpoints (struct usb_device_instance *device)
-{
- int ep;
- struct usb_bus_instance *bus;
- struct usb_endpoint_instance *endpoint;
- unsigned short ep_ptr;
- unsigned short ep_size;
- unsigned short ep_isoc;
- unsigned short ep_doublebuffer;
- int ep_addr;
- int packet_size;
- int buffer_size;
- int attributes;
-
- bus = device->bus;
-
- /* There is a dedicated 2048 byte buffer for USB packets that may be
- * arbitrarily partitioned among the endpoints on 8-byte boundaries.
- * The first 8 bytes are reserved for receiving setup packets on
- * endpoint 0.
- */
- ep_ptr = 8; /* reserve the first 8 bytes for the setup fifo */
-
- for (ep = 0; ep < bus->max_endpoints; ep++) {
- endpoint = bus->endpoint_array + ep;
- ep_addr = endpoint->endpoint_address;
- if ((ep_addr & USB_ENDPOINT_DIR_MASK) == USB_DIR_IN) {
- /* IN endpoint */
- packet_size = endpoint->tx_packetSize;
- attributes = endpoint->tx_attributes;
- } else {
- /* OUT endpoint */
- packet_size = endpoint->rcv_packetSize;
- attributes = endpoint->rcv_attributes;
- }
-
- switch (packet_size) {
- case 0:
- ep_size = 0;
- break;
- case 8:
- ep_size = 0;
- break;
- case 16:
- ep_size = 1;
- break;
- case 32:
- ep_size = 2;
- break;
- case 64:
- ep_size = 3;
- break;
- case 128:
- ep_size = 4;
- break;
- case 256:
- ep_size = 5;
- break;
- case 512:
- ep_size = 6;
- break;
- default:
- UDCDBGA ("ep 0x%02x has bad packet size %d",
- ep_addr, packet_size);
- packet_size = 0;
- ep_size = 0;
- break;
- }
-
- switch (attributes & USB_ENDPOINT_XFERTYPE_MASK) {
- case USB_ENDPOINT_XFER_CONTROL:
- case USB_ENDPOINT_XFER_BULK:
- case USB_ENDPOINT_XFER_INT:
- default:
- /* A non-isochronous endpoint may optionally be
- * double-buffered. For now we disable
- * double-buffering.
- */
- ep_doublebuffer = 0;
- ep_isoc = 0;
- if (packet_size > 64)
- packet_size = 0;
- if (!ep || !ep_doublebuffer)
- buffer_size = packet_size;
- else
- buffer_size = packet_size * 2;
- break;
- case USB_ENDPOINT_XFER_ISOC:
- /* Isochronous endpoints are always double-
- * buffered, but the double-buffering bit
- * in the endpoint configuration register
- * becomes the msb of the endpoint size so we
- * set the double-buffering flag to zero.
- */
- ep_doublebuffer = 0;
- ep_isoc = 1;
- buffer_size = packet_size * 2;
- break;
- }
-
- /* check to see if our packet buffer RAM is exhausted */
- if ((ep_ptr + buffer_size) > 2048) {
- UDCDBGA ("out of packet RAM for ep 0x%02x buf size %d", ep_addr, buffer_size);
- buffer_size = packet_size = 0;
- }
-
- /* force a default configuration for endpoint 0 since it is
- * always enabled
- */
- if (!ep && ((packet_size < 8) || (packet_size > 64))) {
- buffer_size = packet_size = 64;
- ep_size = 3;
- }
-
- if (!ep) {
- /* configure endpoint 0 */
- outw ((ep_size << 12) | (ep_ptr >> 3), UDC_EP0);
- /*UDCDBGA("ep 0 buffer offset 0x%03x packet size 0x%03x", */
- /* ep_ptr, packet_size); */
- } else if ((ep_addr & USB_ENDPOINT_DIR_MASK) == USB_DIR_IN) {
- /* IN endpoint */
- if (packet_size) {
- outw ((1 << 15) | (ep_doublebuffer << 14) |
- (ep_size << 12) | (ep_isoc << 11) |
- (ep_ptr >> 3),
- UDC_EP_TX (ep_addr &
- USB_ENDPOINT_NUMBER_MASK));
- UDCDBGA ("IN ep %d buffer offset 0x%03x"
- " packet size 0x%03x",
- ep_addr & USB_ENDPOINT_NUMBER_MASK,
- ep_ptr, packet_size);
- } else {
- outw (0,
- UDC_EP_TX (ep_addr &
- USB_ENDPOINT_NUMBER_MASK));
- }
- } else {
- /* OUT endpoint */
- if (packet_size) {
- outw ((1 << 15) | (ep_doublebuffer << 14) |
- (ep_size << 12) | (ep_isoc << 11) |
- (ep_ptr >> 3),
- UDC_EP_RX (ep_addr &
- USB_ENDPOINT_NUMBER_MASK));
- UDCDBGA ("OUT ep %d buffer offset 0x%03x"
- " packet size 0x%03x",
- ep_addr & USB_ENDPOINT_NUMBER_MASK,
- ep_ptr, packet_size);
- } else {
- outw (0,
- UDC_EP_RX (ep_addr &
- USB_ENDPOINT_NUMBER_MASK));
- }
- }
- ep_ptr += buffer_size;
- }
-}
-
-/* omap1510_deconfigure_device
- *
- * This function balances omap1510_configure_device.
- */
-static void omap1510_deconfigure_device (void)
-{
- int epnum;
-
- UDCDBG ("clear Cfg_Lock");
- outw (inw (UDC_SYSCON1) & ~UDC_Cfg_Lock, UDC_SYSCON1);
- UDCREG (UDC_SYSCON1);
-
- /* deconfigure all endpoints */
- for (epnum = 1; epnum <= 15; epnum++) {
- outw (0, UDC_EP_RX (epnum));
- outw (0, UDC_EP_TX (epnum));
- }
-}
-
-/* omap1510_configure_device
- *
- * This function implements TRM Figure 14-9.
- */
-static void omap1510_configure_device (struct usb_device_instance *device)
-{
- omap1510_configure_endpoints (device);
-
-
- /* Figure 14-9 indicates we should enable interrupts here, but we have
- * other routines (udc_all_interrupts, udc_suspended_interrupts) to
- * do that.
- */
-
- UDCDBG ("set Cfg_Lock");
- outw (inw (UDC_SYSCON1) | UDC_Cfg_Lock, UDC_SYSCON1);
- UDCREG (UDC_SYSCON1);
-}
-
-/* omap1510_write_noniso_tx_fifo
- *
- * This function implements TRM Figure 14-30.
- *
- * If the endpoint has an active tx_urb, then the next packet of data from the
- * URB is written to the tx FIFO. The total amount of data in the urb is given
- * by urb->actual_length. The maximum amount of data that can be sent in any
- * one packet is given by endpoint->tx_packetSize. The number of data bytes
- * from this URB that have already been transmitted is given by endpoint->sent.
- * endpoint->last is updated by this routine with the number of data bytes
- * transmitted in this packet.
- *
- * In accordance with Figure 14-30, the EP_NUM register must already have been
- * written with the value to select the appropriate tx FIFO before this routine
- * is called.
- */
-static void omap1510_write_noniso_tx_fifo (struct usb_endpoint_instance
- *endpoint)
-{
- struct urb *urb = endpoint->tx_urb;
-
- if (urb) {
- unsigned int last, i;
-
- UDCDBGA ("urb->buffer %p, buffer_length %d, actual_length %d",
- urb->buffer, urb->buffer_length, urb->actual_length);
- if ((last =
- MIN (urb->actual_length - endpoint->sent,
- endpoint->tx_packetSize))) {
- u8 *cp = urb->buffer + endpoint->sent;
-
- UDCDBGA ("endpoint->sent %d, tx_packetSize %d, last %d", endpoint->sent, endpoint->tx_packetSize, last);
-
- if (((u32) cp & 1) == 0) { /* word aligned? */
- outsw (UDC_DATA, cp, last >> 1);
- } else { /* byte aligned. */
- for (i = 0; i < (last >> 1); i++) {
- u16 w = ((u16) cp[2 * i + 1] << 8) |
- (u16) cp[2 * i];
- outw (w, UDC_DATA);
- }
- }
- if (last & 1) {
- outb (*(cp + last - 1), UDC_DATA);
- }
- }
- endpoint->last = last;
- }
-}
-
-/* omap1510_read_noniso_rx_fifo
- *
- * This function implements TRM Figure 14-28.
- *
- * If the endpoint has an active rcv_urb, then the next packet of data is read
- * from the rcv FIFO and written to rcv_urb->buffer at offset
- * rcv_urb->actual_length to append the packet data to the data from any
- * previous packets for this transfer. We assume that there is sufficient room
- * left in the buffer to hold an entire packet of data.
- *
- * The return value is the number of bytes read from the FIFO for this packet.
- *
- * In accordance with Figure 14-28, the EP_NUM register must already have been
- * written with the value to select the appropriate rcv FIFO before this routine
- * is called.
- */
-static int omap1510_read_noniso_rx_fifo (struct usb_endpoint_instance
- *endpoint)
-{
- struct urb *urb = endpoint->rcv_urb;
- int len = 0;
-
- if (urb) {
- len = inw (UDC_RXFSTAT);
-
- if (len) {
- unsigned char *cp = urb->buffer + urb->actual_length;
-
- insw (UDC_DATA, cp, len >> 1);
- if (len & 1)
- *(cp + len - 1) = inb (UDC_DATA);
- }
- }
- return len;
-}
-
-/* omap1510_prepare_for_control_write_status
- *
- * This function implements TRM Figure 14-17.
- *
- * We have to deal here with non-autodecoded control writes that haven't already
- * been dealt with by ep0_recv_setup. The non-autodecoded standard control
- * write requests are: set/clear endpoint feature, set configuration, set
- * interface, and set descriptor. ep0_recv_setup handles set/clear requests for
- * ENDPOINT_HALT by halting the endpoint for a set request and resetting the
- * endpoint for a clear request. ep0_recv_setup returns an error for
- * SET_DESCRIPTOR requests which causes them to be terminated with a stall by
- * the setup handler. A SET_INTERFACE request is handled by ep0_recv_setup by
- * generating a DEVICE_SET_INTERFACE event. This leaves only the
- * SET_CONFIGURATION event for us to deal with here.
- *
- */
-static void omap1510_prepare_for_control_write_status (struct urb *urb)
-{
- struct usb_device_request *request = &urb->device_request;;
-
- /* check for a SET_CONFIGURATION request */
- if (request->bRequest == USB_REQ_SET_CONFIGURATION) {
- int configuration = le16_to_cpu (request->wValue) & 0xff;
- unsigned short devstat = inw (UDC_DEVSTAT);
-
- if ((devstat & (UDC_ADD | UDC_CFG)) == UDC_ADD) {
- /* device is currently in ADDRESSED state */
- if (configuration) {
- /* Assume the specified non-zero configuration
- * value is valid and switch to the CONFIGURED
- * state.
- */
- outw (UDC_Dev_Cfg, UDC_SYSCON2);
- }
- } else if ((devstat & UDC_CFG) == UDC_CFG) {
- /* device is currently in CONFIGURED state */
- if (!configuration) {
- /* Switch to ADDRESSED state. */
- outw (UDC_Clr_Cfg, UDC_SYSCON2);
- }
- }
- }
-
- /* select EP0 tx FIFO */
- outw (UDC_EP_Dir | UDC_EP_Sel, UDC_EP_NUM);
- /* clear endpoint (no data bytes in status stage) */
- outw (UDC_Clr_EP, UDC_CTRL);
- /* enable the EP0 tx FIFO */
- outw (UDC_Set_FIFO_En, UDC_CTRL);
- /* deselect the endpoint */
- outw (UDC_EP_Dir, UDC_EP_NUM);
-}
-
-/* udc_state_transition_up
- * udc_state_transition_down
- *
- * Helper functions to implement device state changes. The device states and
- * the events that transition between them are:
- *
- * STATE_ATTACHED
- * || /\
- * \/ ||
- * DEVICE_HUB_CONFIGURED DEVICE_HUB_RESET
- * || /\
- * \/ ||
- * STATE_POWERED
- * || /\
- * \/ ||
- * DEVICE_RESET DEVICE_POWER_INTERRUPTION
- * || /\
- * \/ ||
- * STATE_DEFAULT
- * || /\
- * \/ ||
- * DEVICE_ADDRESS_ASSIGNED DEVICE_RESET
- * || /\
- * \/ ||
- * STATE_ADDRESSED
- * || /\
- * \/ ||
- * DEVICE_CONFIGURED DEVICE_DE_CONFIGURED
- * || /\
- * \/ ||
- * STATE_CONFIGURED
- *
- * udc_state_transition_up transitions up (in the direction from STATE_ATTACHED
- * to STATE_CONFIGURED) from the specified initial state to the specified final
- * state, passing through each intermediate state on the way. If the initial
- * state is at or above (i.e. nearer to STATE_CONFIGURED) the final state, then
- * no state transitions will take place.
- *
- * udc_state_transition_down transitions down (in the direction from
- * STATE_CONFIGURED to STATE_ATTACHED) from the specified initial state to the
- * specified final state, passing through each intermediate state on the way.
- * If the initial state is at or below (i.e. nearer to STATE_ATTACHED) the final
- * state, then no state transitions will take place.
- *
- * These functions must only be called with interrupts disabled.
- */
-static void udc_state_transition_up (usb_device_state_t initial,
- usb_device_state_t final)
-{
- if (initial < final) {
- switch (initial) {
- case STATE_ATTACHED:
- usbd_device_event_irq (udc_device,
- DEVICE_HUB_CONFIGURED, 0);
- if (final == STATE_POWERED)
- break;
- case STATE_POWERED:
- usbd_device_event_irq (udc_device, DEVICE_RESET, 0);
- if (final == STATE_DEFAULT)
- break;
- case STATE_DEFAULT:
- usbd_device_event_irq (udc_device,
- DEVICE_ADDRESS_ASSIGNED, 0);
- if (final == STATE_ADDRESSED)
- break;
- case STATE_ADDRESSED:
- usbd_device_event_irq (udc_device, DEVICE_CONFIGURED,
- 0);
- case STATE_CONFIGURED:
- break;
- default:
- break;
- }
- }
-}
-
-static void udc_state_transition_down (usb_device_state_t initial,
- usb_device_state_t final)
-{
- if (initial > final) {
- switch (initial) {
- case STATE_CONFIGURED:
- usbd_device_event_irq (udc_device, DEVICE_DE_CONFIGURED, 0);
- if (final == STATE_ADDRESSED)
- break;
- case STATE_ADDRESSED:
- usbd_device_event_irq (udc_device, DEVICE_RESET, 0);
- if (final == STATE_DEFAULT)
- break;
- case STATE_DEFAULT:
- usbd_device_event_irq (udc_device, DEVICE_POWER_INTERRUPTION, 0);
- if (final == STATE_POWERED)
- break;
- case STATE_POWERED:
- usbd_device_event_irq (udc_device, DEVICE_HUB_RESET, 0);
- case STATE_ATTACHED:
- break;
- default:
- break;
- }
- }
-}
-
-/* Handle all device state changes.
- * This function implements TRM Figure 14-21.
- */
-static void omap1510_udc_state_changed (void)
-{
- u16 bits;
- u16 devstat = inw (UDC_DEVSTAT);
-
- UDCDBGA ("state changed, devstat %x, old %x", devstat, udc_devstat);
-
- bits = devstat ^ udc_devstat;
- if (bits) {
- if (bits & UDC_ATT) {
- if (devstat & UDC_ATT) {
- UDCDBG ("device attached and powered");
- udc_state_transition_up (udc_device->device_state, STATE_POWERED);
- } else {
- UDCDBG ("device detached or unpowered");
- udc_state_transition_down (udc_device->device_state, STATE_ATTACHED);
- }
- }
- if (bits & UDC_USB_Reset) {
- if (devstat & UDC_USB_Reset) {
- UDCDBG ("device reset in progess");
- udc_state_transition_down (udc_device->device_state, STATE_POWERED);
- } else {
- UDCDBG ("device reset completed");
- }
- }
- if (bits & UDC_DEF) {
- if (devstat & UDC_DEF) {
- UDCDBG ("device entering default state");
- udc_state_transition_up (udc_device->device_state, STATE_DEFAULT);
- } else {
- UDCDBG ("device leaving default state");
- udc_state_transition_down (udc_device->device_state, STATE_POWERED);
- }
- }
- if (bits & UDC_SUS) {
- if (devstat & UDC_SUS) {
- UDCDBG ("entering suspended state");
- usbd_device_event_irq (udc_device, DEVICE_BUS_INACTIVE, 0);
- } else {
- UDCDBG ("leaving suspended state");
- usbd_device_event_irq (udc_device, DEVICE_BUS_ACTIVITY, 0);
- }
- }
- if (bits & UDC_R_WK_OK) {
- UDCDBGA ("remote wakeup %s", (devstat & UDC_R_WK_OK)
- ? "enabled" : "disabled");
- }
- if (bits & UDC_ADD) {
- if (devstat & UDC_ADD) {
- UDCDBG ("default -> addressed");
- udc_state_transition_up (udc_device->device_state, STATE_ADDRESSED);
- } else {
- UDCDBG ("addressed -> default");
- udc_state_transition_down (udc_device->device_state, STATE_DEFAULT);
- }
- }
- if (bits & UDC_CFG) {
- if (devstat & UDC_CFG) {
- UDCDBG ("device configured");
- /* The ep0_recv_setup function generates the
- * DEVICE_CONFIGURED event when a
- * USB_REQ_SET_CONFIGURATION setup packet is
- * received, so we should already be in the
- * state STATE_CONFIGURED.
- */
- udc_state_transition_up (udc_device->device_state, STATE_CONFIGURED);
- } else {
- UDCDBG ("device deconfigured");
- udc_state_transition_down (udc_device->device_state, STATE_ADDRESSED);
- }
- }
- }
-
- /* Clear interrupt source */
- outw (UDC_DS_Chg, UDC_IRQ_SRC);
-
- /* Save current DEVSTAT */
- udc_devstat = devstat;
-}
-
-/* Handle SETUP USB interrupt.
- * This function implements TRM Figure 14-14.
- */
-static void omap1510_udc_setup (struct usb_endpoint_instance *endpoint)
-{
- UDCDBG ("-> Entering device setup");
-
- do {
- const int setup_pktsize = 8;
- unsigned char *datap =
- (unsigned char *) &ep0_urb->device_request;
-
- /* Gain access to EP 0 setup FIFO */
- outw (UDC_Setup_Sel, UDC_EP_NUM);
-
- /* Read control request data */
- insb (UDC_DATA, datap, setup_pktsize);
-
- UDCDBGA ("EP0 setup read [%x %x %x %x %x %x %x %x]",
- *(datap + 0), *(datap + 1), *(datap + 2),
- *(datap + 3), *(datap + 4), *(datap + 5),
- *(datap + 6), *(datap + 7));
-
- /* Reset EP0 setup FIFO */
- outw (0, UDC_EP_NUM);
- } while (inw (UDC_IRQ_SRC) & UDC_Setup);
-
- /* Try to process setup packet */
- if (ep0_recv_setup (ep0_urb)) {
- /* Not a setup packet, stall next EP0 transaction */
- udc_stall_ep (0);
- UDCDBG ("can't parse setup packet, still waiting for setup");
- return;
- }
-
- /* Check direction */
- if ((ep0_urb->device_request.bmRequestType & USB_REQ_DIRECTION_MASK)
- == USB_REQ_HOST2DEVICE) {
- UDCDBG ("control write on EP0");
- if (le16_to_cpu (ep0_urb->device_request.wLength)) {
- /* We don't support control write data stages.
- * The only standard control write request with a data
- * stage is SET_DESCRIPTOR, and ep0_recv_setup doesn't
- * support that so we just stall those requests. A
- * function driver might support a non-standard
- * write request with a data stage, but it isn't
- * obvious what we would do with the data if we read it
- * so we'll just stall it. It seems like the API isn't
- * quite right here.
- */
-#if 0
- /* Here is what we would do if we did support control
- * write data stages.
- */
- ep0_urb->actual_length = 0;
- outw (0, UDC_EP_NUM);
- /* enable the EP0 rx FIFO */
- outw (UDC_Set_FIFO_En, UDC_CTRL);
-#else
- /* Stall this request */
- UDCDBG ("Stalling unsupported EP0 control write data "
- "stage.");
- udc_stall_ep (0);
-#endif
- } else {
- omap1510_prepare_for_control_write_status (ep0_urb);
- }
- } else {
- UDCDBG ("control read on EP0");
- /* The ep0_recv_setup function has already placed our response
- * packet data in ep0_urb->buffer and the packet length in
- * ep0_urb->actual_length.
- */
- endpoint->tx_urb = ep0_urb;
- endpoint->sent = 0;
- /* select the EP0 tx FIFO */
- outw (UDC_EP_Dir | UDC_EP_Sel, UDC_EP_NUM);
- /* Write packet data to the FIFO. omap1510_write_noniso_tx_fifo
- * will update endpoint->last with the number of bytes written
- * to the FIFO.
- */
- omap1510_write_noniso_tx_fifo (endpoint);
- /* enable the FIFO to start the packet transmission */
- outw (UDC_Set_FIFO_En, UDC_CTRL);
- /* deselect the EP0 tx FIFO */
- outw (UDC_EP_Dir, UDC_EP_NUM);
- }
-
- UDCDBG ("<- Leaving device setup");
-}
-
-/* Handle endpoint 0 RX interrupt
- * This routine implements TRM Figure 14-16.
- */
-static void omap1510_udc_ep0_rx (struct usb_endpoint_instance *endpoint)
-{
- unsigned short status;
-
- UDCDBG ("RX on EP0");
- /* select EP0 rx FIFO */
- outw (UDC_EP_Sel, UDC_EP_NUM);
-
- status = inw (UDC_STAT_FLG);
-
- if (status & UDC_ACK) {
- /* Check direction */
- if ((ep0_urb->device_request.bmRequestType
- & USB_REQ_DIRECTION_MASK) == USB_REQ_HOST2DEVICE) {
- /* This rx interrupt must be for a control write data
- * stage packet.
- *
- * We don't support control write data stages.
- * We should never end up here.
- */
-
- /* clear the EP0 rx FIFO */
- outw (UDC_Clr_EP, UDC_CTRL);
-
- /* deselect the EP0 rx FIFO */
- outw (0, UDC_EP_NUM);
-
- UDCDBG ("Stalling unexpected EP0 control write "
- "data stage packet");
- udc_stall_ep (0);
- } else {
- /* This rx interrupt must be for a control read status
- * stage packet.
- */
- UDCDBG ("ACK on EP0 control read status stage packet");
- /* deselect EP0 rx FIFO */
- outw (0, UDC_EP_NUM);
- }
- } else if (status & UDC_STALL) {
- UDCDBG ("EP0 stall during RX");
- /* deselect EP0 rx FIFO */
- outw (0, UDC_EP_NUM);
- } else {
- /* deselect EP0 rx FIFO */
- outw (0, UDC_EP_NUM);
- }
-}
-
-/* Handle endpoint 0 TX interrupt
- * This routine implements TRM Figure 14-18.
- */
-static void omap1510_udc_ep0_tx (struct usb_endpoint_instance *endpoint)
-{
- unsigned short status;
- struct usb_device_request *request = &ep0_urb->device_request;
-
- UDCDBG ("TX on EP0");
- /* select EP0 TX FIFO */
- outw (UDC_EP_Dir | UDC_EP_Sel, UDC_EP_NUM);
-
- status = inw (UDC_STAT_FLG);
- if (status & UDC_ACK) {
- /* Check direction */
- if ((request->bmRequestType & USB_REQ_DIRECTION_MASK) ==
- USB_REQ_HOST2DEVICE) {
- /* This tx interrupt must be for a control write status
- * stage packet.
- */
- UDCDBG ("ACK on EP0 control write status stage packet");
- /* deselect EP0 TX FIFO */
- outw (UDC_EP_Dir, UDC_EP_NUM);
- } else {
- /* This tx interrupt must be for a control read data
- * stage packet.
- */
- int wLength = le16_to_cpu (request->wLength);
-
- /* Update our count of bytes sent so far in this
- * transfer.
- */
- endpoint->sent += endpoint->last;
-
- /* We are finished with this transfer if we have sent
- * all of the bytes in our tx urb (urb->actual_length)
- * unless we need a zero-length terminating packet. We
- * need a zero-length terminating packet if we returned
- * fewer bytes than were requested (wLength) by the host,
- * and the number of bytes we returned is an exact
- * multiple of the packet size endpoint->tx_packetSize.
- */
- if ((endpoint->sent == ep0_urb->actual_length)
- && ((ep0_urb->actual_length == wLength)
- || (endpoint->last !=
- endpoint->tx_packetSize))) {
- /* Done with control read data stage. */
- UDCDBG ("control read data stage complete");
- /* deselect EP0 TX FIFO */
- outw (UDC_EP_Dir, UDC_EP_NUM);
- /* select EP0 RX FIFO to prepare for control
- * read status stage.
- */
- outw (UDC_EP_Sel, UDC_EP_NUM);
- /* clear the EP0 RX FIFO */
- outw (UDC_Clr_EP, UDC_CTRL);
- /* enable the EP0 RX FIFO */
- outw (UDC_Set_FIFO_En, UDC_CTRL);
- /* deselect the EP0 RX FIFO */
- outw (0, UDC_EP_NUM);
- } else {
- /* We still have another packet of data to send
- * in this control read data stage or else we
- * need a zero-length terminating packet.
- */
- UDCDBG ("ACK control read data stage packet");
- omap1510_write_noniso_tx_fifo (endpoint);
- /* enable the EP0 tx FIFO to start transmission */
- outw (UDC_Set_FIFO_En, UDC_CTRL);
- /* deselect EP0 TX FIFO */
- outw (UDC_EP_Dir, UDC_EP_NUM);
- }
- }
- } else if (status & UDC_STALL) {
- UDCDBG ("EP0 stall during TX");
- /* deselect EP0 TX FIFO */
- outw (UDC_EP_Dir, UDC_EP_NUM);
- } else {
- /* deselect EP0 TX FIFO */
- outw (UDC_EP_Dir, UDC_EP_NUM);
- }
-}
-
-/* Handle RX transaction on non-ISO endpoint.
- * This function implements TRM Figure 14-27.
- * The ep argument is a physical endpoint number for a non-ISO OUT endpoint
- * in the range 1 to 15.
- */
-static void omap1510_udc_epn_rx (int ep)
-{
- unsigned short status;
-
- /* Check endpoint status */
- status = inw (UDC_STAT_FLG);
-
- if (status & UDC_ACK) {
- int nbytes;
- struct usb_endpoint_instance *endpoint =
- omap1510_find_ep (ep);
-
- nbytes = omap1510_read_noniso_rx_fifo (endpoint);
- usbd_rcv_complete (endpoint, nbytes, 0);
-
- /* enable rx FIFO to prepare for next packet */
- outw (UDC_Set_FIFO_En, UDC_CTRL);
- } else if (status & UDC_STALL) {
- UDCDBGA ("STALL on RX endpoint %d", ep);
- } else if (status & UDC_NAK) {
- UDCDBGA ("NAK on RX ep %d", ep);
- } else {
- serial_printf ("omap-bi: RX on ep %d with status %x", ep,
- status);
- }
-}
-
-/* Handle TX transaction on non-ISO endpoint.
- * This function implements TRM Figure 14-29.
- * The ep argument is a physical endpoint number for a non-ISO IN endpoint
- * in the range 16 to 30.
- */
-static void omap1510_udc_epn_tx (int ep)
-{
- unsigned short status;
-
- /*serial_printf("omap1510_udc_epn_tx( %x )\n",ep); */
-
- /* Check endpoint status */
- status = inw (UDC_STAT_FLG);
-
- if (status & UDC_ACK) {
- struct usb_endpoint_instance *endpoint =
- omap1510_find_ep (ep);
-
- /* We need to transmit a terminating zero-length packet now if
- * we have sent all of the data in this URB and the transfer
- * size was an exact multiple of the packet size.
- */
- if (endpoint->tx_urb
- && (endpoint->last == endpoint->tx_packetSize)
- && (endpoint->tx_urb->actual_length - endpoint->sent -
- endpoint->last == 0)) {
- /* Prepare to transmit a zero-length packet. */
- endpoint->sent += endpoint->last;
- /* write 0 bytes of data to FIFO */
- omap1510_write_noniso_tx_fifo (endpoint);
- /* enable tx FIFO to start transmission */
- outw (UDC_Set_FIFO_En, UDC_CTRL);
- } else if (endpoint->tx_urb
- && endpoint->tx_urb->actual_length) {
- /* retire the data that was just sent */
- usbd_tx_complete (endpoint);
- /* Check to see if we have more data ready to transmit
- * now.
- */
- if (endpoint->tx_urb
- && endpoint->tx_urb->actual_length) {
- /* write data to FIFO */
- omap1510_write_noniso_tx_fifo (endpoint);
- /* enable tx FIFO to start transmission */
- outw (UDC_Set_FIFO_En, UDC_CTRL);
- }
- }
- } else if (status & UDC_STALL) {
- UDCDBGA ("STALL on TX endpoint %d", ep);
- } else if (status & UDC_NAK) {
- UDCDBGA ("NAK on TX endpoint %d", ep);
- } else {
- /*serial_printf("omap-bi: TX on ep %d with status %x\n", ep, status); */
- }
-}
-
-
-/*
--------------------------------------------------------------------------------
-*/
-
-/* Handle general USB interrupts and dispatch according to type.
- * This function implements TRM Figure 14-13.
- */
-void omap1510_udc_irq (void)
-{
- u16 irq_src = inw (UDC_IRQ_SRC);
- int valid_irq = 0;
-
- if (!(irq_src & ~UDC_SOF_Flg)) /* ignore SOF interrupts ) */
- return;
-
- UDCDBGA ("< IRQ #%d start >- %x", udc_interrupts, irq_src);
- /*serial_printf("< IRQ #%d start >- %x\n", udc_interrupts, irq_src); */
-
- if (irq_src & UDC_DS_Chg) {
- /* Device status changed */
- omap1510_udc_state_changed ();
- valid_irq++;
- }
- if (irq_src & UDC_EP0_RX) {
- /* Endpoint 0 receive */
- outw (UDC_EP0_RX, UDC_IRQ_SRC); /* ack interrupt */
- omap1510_udc_ep0_rx (udc_device->bus->endpoint_array + 0);
- valid_irq++;
- }
- if (irq_src & UDC_EP0_TX) {
- /* Endpoint 0 transmit */
- outw (UDC_EP0_TX, UDC_IRQ_SRC); /* ack interrupt */
- omap1510_udc_ep0_tx (udc_device->bus->endpoint_array + 0);
- valid_irq++;
- }
- if (irq_src & UDC_Setup) {
- /* Device setup */
- omap1510_udc_setup (udc_device->bus->endpoint_array + 0);
- valid_irq++;
- }
- /*if (!valid_irq) */
- /* serial_printf("unknown interrupt, IRQ_SRC %.4x\n", irq_src); */
- UDCDBGA ("< IRQ #%d end >", udc_interrupts);
- udc_interrupts++;
-}
-
-/* This function implements TRM Figure 14-26. */
-void omap1510_udc_noniso_irq (void)
-{
- unsigned short epnum;
- unsigned short irq_src = inw (UDC_IRQ_SRC);
- int valid_irq = 0;
-
- if (!(irq_src & (UDC_EPn_RX | UDC_EPn_TX)))
- return;
-
- UDCDBGA ("non-ISO IRQ, IRQ_SRC %x", inw (UDC_IRQ_SRC));
-
- if (irq_src & UDC_EPn_RX) { /* Endpoint N OUT transaction */
- /* Determine the endpoint number for this interrupt */
- epnum = (inw (UDC_EPN_STAT) & 0x0f00) >> 8;
- UDCDBGA ("RX on ep %x", epnum);
-
- /* acknowledge interrupt */
- outw (UDC_EPn_RX, UDC_IRQ_SRC);
-
- if (epnum) {
- /* select the endpoint FIFO */
- outw (UDC_EP_Sel | epnum, UDC_EP_NUM);
-
- omap1510_udc_epn_rx (epnum);
-
- /* deselect the endpoint FIFO */
- outw (epnum, UDC_EP_NUM);
- }
- valid_irq++;
- }
- if (irq_src & UDC_EPn_TX) { /* Endpoint N IN transaction */
- /* Determine the endpoint number for this interrupt */
- epnum = (inw (UDC_EPN_STAT) & 0x000f) | USB_DIR_IN;
- UDCDBGA ("TX on ep %x", epnum);
-
- /* acknowledge interrupt */
- outw (UDC_EPn_TX, UDC_IRQ_SRC);
-
- if (epnum) {
- /* select the endpoint FIFO */
- outw (UDC_EP_Sel | UDC_EP_Dir | epnum, UDC_EP_NUM);
-
- omap1510_udc_epn_tx (epnum);
-
- /* deselect the endpoint FIFO */
- outw (UDC_EP_Dir | epnum, UDC_EP_NUM);
- }
- valid_irq++;
- }
- if (!valid_irq)
- serial_printf (": unknown non-ISO interrupt, IRQ_SRC %.4x\n",
- irq_src);
-}
-
-/*
--------------------------------------------------------------------------------
-*/
-
-
-/*
- * Start of public functions.
- */
-
-/* Called to start packet transmission. */
-int udc_endpoint_write (struct usb_endpoint_instance *endpoint)
-{
- unsigned short epnum =
- endpoint->endpoint_address & USB_ENDPOINT_NUMBER_MASK;
-
- UDCDBGA ("Starting transmit on ep %x", epnum);
-
- if (endpoint->tx_urb) {
- /* select the endpoint FIFO */
- outw (UDC_EP_Sel | UDC_EP_Dir | epnum, UDC_EP_NUM);
- /* write data to FIFO */
- omap1510_write_noniso_tx_fifo (endpoint);
- /* enable tx FIFO to start transmission */
- outw (UDC_Set_FIFO_En, UDC_CTRL);
- /* deselect the endpoint FIFO */
- outw (UDC_EP_Dir | epnum, UDC_EP_NUM);
- }
-
- return 0;
-}
-
-/* Start to initialize h/w stuff */
-int udc_init (void)
-{
- u16 udc_rev;
- uchar value;
- ulong gpio;
- int i;
-
- /* Let the device settle down before we start */
- for (i = 0; i < UDC_INIT_MDELAY; i++) udelay(1000);
-
- udc_device = NULL;
-
- UDCDBG ("starting");
-
- /* Check peripheral reset. Must be 1 to make sure
- MPU TIPB peripheral reset is inactive */
- UDCREG (ARM_RSTCT2);
-
- /* Set and check clock control.
- * We might ought to be using the clock control API to do
- * this instead of fiddling with the clock registers directly
- * here.
- */
- outw ((1 << 4) | (1 << 5), CLOCK_CTRL);
- UDCREG (CLOCK_CTRL);
-
- /* Set and check SOFT
- * The below line of code has been changed to perform a
- * read-modify-write instead of a simple write for
- * configuring the SOFT_REQ register. This allows the code
- * to be compatible with OMAP5912 and OMAP16xx devices
- */
- outw ((1 << 4) | (1 << 3) | 1 | (inw(SOFT_REQ)), SOFT_REQ);
-
- /* Short delay to wait for DPLL */
- udelay (1000);
-
- /* Print banner with device revision */
- udc_rev = inw (UDC_REV) & 0xff;
-
-#ifdef CONFIG_OMAP1610
- printf ("USB: TI OMAP5912 USB function module rev %d.%d\n",
- udc_rev >> 4, udc_rev & 0xf);
-#endif
-
- /* The VBUS_MODE bit selects whether VBUS detection is done via
- * software (1) or hardware (0). When software detection is
- * selected, VBUS_CTRL selects whether USB is not connected (0)
- * or connected (1).
- */
- outl (inl (FUNC_MUX_CTRL_0) | UDC_VBUS_MODE, FUNC_MUX_CTRL_0);
- outl (inl (FUNC_MUX_CTRL_0) & ~UDC_VBUS_CTRL, FUNC_MUX_CTRL_0);
- UDCREGL (FUNC_MUX_CTRL_0);
-
- /*
- * At this point, device is ready for configuration...
- */
-
- UDCDBG ("disable USB interrupts");
- outw (0, UDC_IRQ_EN);
- UDCREG (UDC_IRQ_EN);
-
- UDCDBG ("disable USB DMA");
- outw (0, UDC_DMA_IRQ_EN);
- UDCREG (UDC_DMA_IRQ_EN);
-
- UDCDBG ("initialize SYSCON1");
- outw (UDC_Self_Pwr | UDC_Pullup_En, UDC_SYSCON1);
- UDCREG (UDC_SYSCON1);
-
- return 0;
-}
-
-/* Stall endpoint */
-static void udc_stall_ep (unsigned int ep_addr)
-{
- /*int ep_addr = PHYS_EP_TO_EP_ADDR(ep); */
- int ep_num = ep_addr & USB_ENDPOINT_NUMBER_MASK;
-
- UDCDBGA ("stall ep_addr %d", ep_addr);
-
- /* REVISIT?
- * The OMAP TRM section 14.2.4.2 says we must check that the FIFO
- * is empty before halting the endpoint. The current implementation
- * doesn't check that the FIFO is empty.
- */
-
- if (!ep_num) {
- outw (UDC_Stall_Cmd, UDC_SYSCON2);
- } else if ((ep_addr & USB_ENDPOINT_DIR_MASK) == USB_DIR_OUT) {
- if (inw (UDC_EP_RX (ep_num)) & UDC_EPn_RX_Valid) {
- /* we have a valid rx endpoint, so halt it */
- outw (UDC_EP_Sel | ep_num, UDC_EP_NUM);
- outw (UDC_Set_Halt, UDC_CTRL);
- outw (ep_num, UDC_EP_NUM);
- }
- } else {
- if (inw (UDC_EP_TX (ep_num)) & UDC_EPn_TX_Valid) {
- /* we have a valid tx endpoint, so halt it */
- outw (UDC_EP_Sel | UDC_EP_Dir | ep_num, UDC_EP_NUM);
- outw (UDC_Set_Halt, UDC_CTRL);
- outw (ep_num, UDC_EP_NUM);
- }
- }
-}
-
-/* Reset endpoint */
-#if 0
-static void udc_reset_ep (unsigned int ep_addr)
-{
- /*int ep_addr = PHYS_EP_TO_EP_ADDR(ep); */
- int ep_num = ep_addr & USB_ENDPOINT_NUMBER_MASK;
-
- UDCDBGA ("reset ep_addr %d", ep_addr);
-
- if (!ep_num) {
- /* control endpoint 0 can't be reset */
- } else if ((ep_addr & USB_ENDPOINT_DIR_MASK) == USB_DIR_OUT) {
- UDCDBGA ("UDC_EP_RX(%d) = 0x%04x", ep_num,
- inw (UDC_EP_RX (ep_num)));
- if (inw (UDC_EP_RX (ep_num)) & UDC_EPn_RX_Valid) {
- /* we have a valid rx endpoint, so reset it */
- outw (ep_num | UDC_EP_Sel, UDC_EP_NUM);
- outw (UDC_Reset_EP, UDC_CTRL);
- outw (ep_num, UDC_EP_NUM);
- UDCDBGA ("OUT endpoint %d reset", ep_num);
- }
- } else {
- UDCDBGA ("UDC_EP_TX(%d) = 0x%04x", ep_num,
- inw (UDC_EP_TX (ep_num)));
- /* Resetting of tx endpoints seems to be causing the USB function
- * module to fail, which causes problems when the driver is
- * uninstalled. We'll skip resetting tx endpoints for now until
- * we figure out what the problem is.
- */
-#if 0
- if (inw (UDC_EP_TX (ep_num)) & UDC_EPn_TX_Valid) {
- /* we have a valid tx endpoint, so reset it */
- outw (ep_num | UDC_EP_Dir | UDC_EP_Sel, UDC_EP_NUM);
- outw (UDC_Reset_EP, UDC_CTRL);
- outw (ep_num | UDC_EP_Dir, UDC_EP_NUM);
- UDCDBGA ("IN endpoint %d reset", ep_num);
- }
-#endif
- }
-}
-#endif
-
-/* ************************************************************************** */
-
-/**
- * udc_check_ep - check logical endpoint
- *
- * Return physical endpoint number to use for this logical endpoint or zero if not valid.
- */
-#if 0
-int udc_check_ep (int logical_endpoint, int packetsize)
-{
- if ((logical_endpoint == 0x80) ||
- ((logical_endpoint & 0x8f) != logical_endpoint)) {
- return 0;
- }
-
- switch (packetsize) {
- case 8:
- case 16:
- case 32:
- case 64:
- case 128:
- case 256:
- case 512:
- break;
- default:
- return 0;
- }
-
- return EP_ADDR_TO_PHYS_EP (logical_endpoint);
-}
-#endif
-
-/*
- * udc_setup_ep - setup endpoint
- *
- * Associate a physical endpoint with endpoint_instance
- */
-void udc_setup_ep (struct usb_device_instance *device,
- unsigned int ep, struct usb_endpoint_instance *endpoint)
-{
- UDCDBGA ("setting up endpoint addr %x", endpoint->endpoint_address);
-
- /* This routine gets called by bi_modinit for endpoint 0 and from
- * bi_config for all of the other endpoints. bi_config gets called
- * during the DEVICE_CREATE, DEVICE_CONFIGURED, and
- * DEVICE_SET_INTERFACE events. We need to reconfigure the OMAP packet
- * RAM after bi_config scans the selected device configuration and
- * initializes the endpoint structures, but before this routine enables
- * the OUT endpoint FIFOs. Since bi_config calls this routine in a
- * loop for endpoints 1 through UDC_MAX_ENDPOINTS, we reconfigure our
- * packet RAM here when ep==1.
- * I really hate to do this here, but it seems like the API exported
- * by the USB bus interface controller driver to the usbd-bi module
- * isn't quite right so there is no good place to do this.
- */
- if (ep == 1) {
- omap1510_deconfigure_device ();
- omap1510_configure_device (device);
- }
-
- if (endpoint && (ep < UDC_MAX_ENDPOINTS)) {
- int ep_addr = endpoint->endpoint_address;
-
- if (!ep_addr) {
- /* nothing to do for endpoint 0 */
- } else if ((ep_addr & USB_ENDPOINT_DIR_MASK) == USB_DIR_IN) {
- /* nothing to do for IN (tx) endpoints */
- } else { /* OUT (rx) endpoint */
- if (endpoint->rcv_packetSize) {
- /*struct urb* urb = &(urb_out_array[ep&0xFF]); */
- /*urb->endpoint = endpoint; */
- /*urb->device = device; */
- /*urb->buffer_length = sizeof(urb->buffer); */
-
- /*endpoint->rcv_urb = urb; */
- omap1510_prepare_endpoint_for_rx (ep_addr);
- }
- }
- }
-}
-
-/**
- * udc_disable_ep - disable endpoint
- * @ep:
- *
- * Disable specified endpoint
- */
-#if 0
-void udc_disable_ep (unsigned int ep_addr)
-{
- /*int ep_addr = PHYS_EP_TO_EP_ADDR(ep); */
- int ep_num = ep_addr & USB_ENDPOINT_NUMBER_MASK;
- struct usb_endpoint_instance *endpoint = omap1510_find_ep (ep_addr); /*udc_device->bus->endpoint_array + ep; */
-
- UDCDBGA ("disable ep_addr %d", ep_addr);
-
- if (!ep_num) {
- /* nothing to do for endpoint 0 */ ;
- } else if ((ep_addr & USB_ENDPOINT_DIR_MASK) == USB_DIR_IN) {
- if (endpoint->tx_packetSize) {
- /* we have a valid tx endpoint */
- /*usbd_flush_tx(endpoint); */
- endpoint->tx_urb = NULL;
- }
- } else {
- if (endpoint->rcv_packetSize) {
- /* we have a valid rx endpoint */
- /*usbd_flush_rcv(endpoint); */
- endpoint->rcv_urb = NULL;
- }
- }
-}
-#endif
-
-/* ************************************************************************** */
-
-/**
- * udc_connected - is the USB cable connected
- *
- * Return non-zero if cable is connected.
- */
-#if 0
-int udc_connected (void)
-{
- return ((inw (UDC_DEVSTAT) & UDC_ATT) == UDC_ATT);
-}
-#endif
-
-/* Turn on the USB connection by enabling the pullup resistor */
-void udc_connect (void)
-{
- UDCDBG ("connect, enable Pullup");
- outl (0x00000018, FUNC_MUX_CTRL_D);
-}
-
-/* Turn off the USB connection by disabling the pullup resistor */
-void udc_disconnect (void)
-{
- UDCDBG ("disconnect, disable Pullup");
- outl (0x00000000, FUNC_MUX_CTRL_D);
-}
-
-/* ************************************************************************** */
-
-
-/*
- * udc_disable_interrupts - disable interrupts
- * switch off interrupts
- */
-#if 0
-void udc_disable_interrupts (struct usb_device_instance *device)
-{
- UDCDBG ("disabling all interrupts");
- outw (0, UDC_IRQ_EN);
-}
-#endif
-
-/* ************************************************************************** */
-
-/**
- * udc_ep0_packetsize - return ep0 packetsize
- */
-#if 0
-int udc_ep0_packetsize (void)
-{
- return EP0_PACKETSIZE;
-}
-#endif
-
-/* Switch on the UDC */
-void udc_enable (struct usb_device_instance *device)
-{
- UDCDBGA ("enable device %p, status %d", device, device->status);
-
- /* initialize driver state variables */
- udc_devstat = 0;
-
- /* Save the device structure pointer */
- udc_device = device;
-
- /* Setup ep0 urb */
- if (!ep0_urb) {
- ep0_urb =
- usbd_alloc_urb (udc_device,
- udc_device->bus->endpoint_array);
- } else {
- serial_printf ("udc_enable: ep0_urb already allocated %p\n",
- ep0_urb);
- }
-
- UDCDBG ("Check clock status");
- UDCREG (STATUS_REQ);
-
- /* The VBUS_MODE bit selects whether VBUS detection is done via
- * software (1) or hardware (0). When software detection is
- * selected, VBUS_CTRL selects whether USB is not connected (0)
- * or connected (1).
- */
- outl (inl (FUNC_MUX_CTRL_0) | UDC_VBUS_CTRL | UDC_VBUS_MODE,
- FUNC_MUX_CTRL_0);
- UDCREGL (FUNC_MUX_CTRL_0);
-
- omap1510_configure_device (device);
-}
-
-/* Switch off the UDC */
-void udc_disable (void)
-{
- UDCDBG ("disable UDC");
-
- omap1510_deconfigure_device ();
-
- /* The VBUS_MODE bit selects whether VBUS detection is done via
- * software (1) or hardware (0). When software detection is
- * selected, VBUS_CTRL selects whether USB is not connected (0)
- * or connected (1).
- */
- outl (inl (FUNC_MUX_CTRL_0) | UDC_VBUS_MODE, FUNC_MUX_CTRL_0);
- outl (inl (FUNC_MUX_CTRL_0) & ~UDC_VBUS_CTRL, FUNC_MUX_CTRL_0);
- UDCREGL (FUNC_MUX_CTRL_0);
-
- /* Free ep0 URB */
- if (ep0_urb) {
- /*usbd_dealloc_urb(ep0_urb); */
- ep0_urb = NULL;
- }
-
- /* Reset device pointer.
- * We ought to do this here to balance the initialization of udc_device
- * in udc_enable, but some of our other exported functions get called
- * by the bus interface driver after udc_disable, so we have to hang on
- * to the device pointer to avoid a null pointer dereference. */
- /* udc_device = NULL; */
-}
-
-/**
- * udc_startup - allow udc code to do any additional startup
- */
-void udc_startup_events (struct usb_device_instance *device)
-{
- /* The DEVICE_INIT event puts the USB device in the state STATE_INIT. */
- usbd_device_event_irq (device, DEVICE_INIT, 0);
-
- /* The DEVICE_CREATE event puts the USB device in the state
- * STATE_ATTACHED.
- */
- usbd_device_event_irq (device, DEVICE_CREATE, 0);
-
- /* Some USB controller driver implementations signal
- * DEVICE_HUB_CONFIGURED and DEVICE_RESET events here.
- * DEVICE_HUB_CONFIGURED causes a transition to the state STATE_POWERED,
- * and DEVICE_RESET causes a transition to the state STATE_DEFAULT.
- * The OMAP USB client controller has the capability to detect when the
- * USB cable is connected to a powered USB bus via the ATT bit in the
- * DEVSTAT register, so we will defer the DEVICE_HUB_CONFIGURED and
- * DEVICE_RESET events until later.
- */
-
- udc_enable (device);
-}
-
-/**
- * udc_irq - do pseudo interrupts
- */
-void udc_irq(void)
-{
- /* Loop while we have interrupts.
- * If we don't do this, the input chain
- * polling delay is likely to miss
- * host requests.
- */
- while (inw (UDC_IRQ_SRC) & ~UDC_SOF_Flg) {
- /* Handle any new IRQs */
- omap1510_udc_irq ();
- omap1510_udc_noniso_irq ();
- }
-}
-
-/* Flow control */
-void udc_set_nak(int epid)
-{
- /* TODO: implement this functionality in omap1510 */
-}
-
-void udc_unset_nak (int epid)
-{
- /* TODO: implement this functionality in omap1510 */
-}
+++ /dev/null
-/*
- *
- * BRIEF MODULE DESCRIPTION
- * OMAP hardware map
- *
- * Copyright (C) 2001 RidgeRun, Inc. (http://www.ridgerun.com)
- * Author: RidgeRun, Inc.
- * Greg Lonnon (glonnon@ridgerun.com) or info@ridgerun.com
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <linux/sizes.h>
-
-/*
- There are 2 sets of general I/O -->
- 1. GPIO (shared between ARM & DSP, configured by ARM)
- 2. MPUIO which can be used only by the ARM.
-
- Base address FFFB:5000 is where the ARM accesses the MPUIO control registers
- (see 7.2.2 of the TRM for MPUIO reg definitions).
-
- Base address E101:5000 is reserved for ARM access of the same MPUIO control
- regs, but via the DSP I/O map. This address is unavailable on 1510.
-
- Base address FFFC:E000 is where the ARM accesses the GPIO config registers
- directly via its own peripheral bus.
-
- Base address E101:E000 is where the ARM can access the same GPIO config
- registers, but the access takes place through the ARM port interface (called
- API or MPUI) via the DSP's peripheral bus (DSP I/O space).
-
- Therefore, the ARM should setup the GPIO regs thru the FFFC:E000 addresses
- instead of the E101:E000 addresses. The DSP has only read access of the pin
- control register, so this may explain the inability to write to E101:E018.
- Try accessing pin control reg at FFFC:E018.
- */
-#define OMAP1510_GPIO_BASE 0xfffce000
-#define OMAP1510_GPIO_START OMAP1510_GPIO_BASE
-#define OMAP1510_GPIO_SIZE SZ_4K
-
-#define OMAP1510_MCBSP1_BASE 0xE1011000
-#define OMAP1510_MCBSP1_SIZE SZ_4K
-#define OMAP1510_MCBSP1_START 0xE1011000
-
-#define OMAP1510_MCBSP2_BASE 0xFFFB1000
-
-#define OMAP1510_MCBSP3_BASE 0xE1017000
-#define OMAP1510_MCBSP3_SIZE SZ_4K
-#define OMAP1510_MCBSP3_START 0xE1017000
-
-/*
- * Where's the flush address (for flushing D and I cache?)
- */
-#define FLUSH_BASE 0xdf000000
-#define FLUSH_BASE_PHYS 0x00000000
-
-#ifndef __ASSEMBLER__
-
-#define PCIO_BASE 0
-
-/*
- * RAM definitions
- */
-#define MAPTOPHYS(a) ((unsigned long)(a) - PAGE_OFFSET)
-#define KERNTOPHYS(a) ((unsigned long)(&a))
-#define KERNEL_BASE (0x10008000)
-#endif
-
-/* macro to get at IO space when running virtually */
-#define IO_ADDRESS(x) ((x))
-
-/* ----------------------------------------------------------------------------
- * OMAP1510 system registers
- * ----------------------------------------------------------------------------
- */
-
-#define OMAP1510_UART1_BASE 0xfffb0000 /* "BLUETOOTH-UART" */
-#define OMAP1510_UART2_BASE 0xfffb0800 /* "MODEM-UART" */
-#define OMAP1510_RTC_BASE 0xfffb4800 /* RTC */
-#define OMAP1510_UART3_BASE 0xfffb9800 /* Shared MPU/DSP UART */
-#define OMAP1510_COM_MCBSP2_BASE 0xffff1000 /* Com McBSP2 */
-#define OMAP1510_AUDIO_MCBSP_BASE 0xffff1800 /* Audio McBSP2 */
-#define OMAP1510_ARMIO_BASE 0xfffb5000 /* keyboard/gpio */
-
-/*
- * OMAP1510 UART3 Registers
- */
-
-#define OMAP_MPU_UART3_BASE 0xFFFB9800 /* UART3 through MPU bus */
-
-/* UART3 Registers Maping through MPU bus */
-
-#define UART3_RHR (OMAP_MPU_UART3_BASE + 0)
-#define UART3_THR (OMAP_MPU_UART3_BASE + 0)
-#define UART3_DLL (OMAP_MPU_UART3_BASE + 0)
-#define UART3_IER (OMAP_MPU_UART3_BASE + 4)
-#define UART3_DLH (OMAP_MPU_UART3_BASE + 4)
-#define UART3_IIR (OMAP_MPU_UART3_BASE + 8)
-#define UART3_FCR (OMAP_MPU_UART3_BASE + 8)
-#define UART3_EFR (OMAP_MPU_UART3_BASE + 8)
-#define UART3_LCR (OMAP_MPU_UART3_BASE + 0x0C)
-#define UART3_MCR (OMAP_MPU_UART3_BASE + 0x10)
-#define UART3_XON1_ADDR1 (OMAP_MPU_UART3_BASE + 0x10)
-#define UART3_XON2_ADDR2 (OMAP_MPU_UART3_BASE + 0x14)
-#define UART3_LSR (OMAP_MPU_UART3_BASE + 0x14)
-#define UART3_TCR (OMAP_MPU_UART3_BASE + 0x18)
-#define UART3_MSR (OMAP_MPU_UART3_BASE + 0x18)
-#define UART3_XOFF1 (OMAP_MPU_UART3_BASE + 0x18)
-#define UART3_XOFF2 (OMAP_MPU_UART3_BASE + 0x1C)
-#define UART3_SPR (OMAP_MPU_UART3_BASE + 0x1C)
-#define UART3_TLR (OMAP_MPU_UART3_BASE + 0x1C)
-#define UART3_MDR1 (OMAP_MPU_UART3_BASE + 0x20)
-#define UART3_MDR2 (OMAP_MPU_UART3_BASE + 0x24)
-#define UART3_SFLSR (OMAP_MPU_UART3_BASE + 0x28)
-#define UART3_TXFLL (OMAP_MPU_UART3_BASE + 0x28)
-#define UART3_RESUME (OMAP_MPU_UART3_BASE + 0x2C)
-#define UART3_TXFLH (OMAP_MPU_UART3_BASE + 0x2C)
-#define UART3_SFREGL (OMAP_MPU_UART3_BASE + 0x30)
-#define UART3_RXFLL (OMAP_MPU_UART3_BASE + 0x30)
-#define UART3_SFREGH (OMAP_MPU_UART3_BASE + 0x34)
-#define UART3_RXFLH (OMAP_MPU_UART3_BASE + 0x34)
-#define UART3_BLR (OMAP_MPU_UART3_BASE + 0x38)
-#define UART3_ACREG (OMAP_MPU_UART3_BASE + 0x3C)
-#define UART3_DIV16 (OMAP_MPU_UART3_BASE + 0x3C)
-#define UART3_SCR (OMAP_MPU_UART3_BASE + 0x40)
-#define UART3_SSR (OMAP_MPU_UART3_BASE + 0x44)
-#define UART3_EBLR (OMAP_MPU_UART3_BASE + 0x48)
-#define UART3_OSC_12M_SEL (OMAP_MPU_UART3_BASE + 0x4C)
-#define UART3_MVR (OMAP_MPU_UART3_BASE + 0x50)
-
-/*
- * Configuration Registers
- */
-#define FUNC_MUX_CTRL_0 0xfffe1000
-#define FUNC_MUX_CTRL_1 0xfffe1004
-#define FUNC_MUX_CTRL_2 0xfffe1008
-#define COMP_MODE_CTRL_0 0xfffe100c
-#define FUNC_MUX_CTRL_3 0xfffe1010
-#define FUNC_MUX_CTRL_4 0xfffe1014
-#define FUNC_MUX_CTRL_5 0xfffe1018
-#define FUNC_MUX_CTRL_6 0xfffe101C
-#define FUNC_MUX_CTRL_7 0xfffe1020
-#define FUNC_MUX_CTRL_8 0xfffe1024
-#define FUNC_MUX_CTRL_9 0xfffe1028
-#define FUNC_MUX_CTRL_A 0xfffe102C
-#define FUNC_MUX_CTRL_B 0xfffe1030
-#define FUNC_MUX_CTRL_C 0xfffe1034
-#define FUNC_MUX_CTRL_D 0xfffe1038
-#define PULL_DWN_CTRL_0 0xfffe1040
-#define PULL_DWN_CTRL_1 0xfffe1044
-#define PULL_DWN_CTRL_2 0xfffe1048
-#define PULL_DWN_CTRL_3 0xfffe104c
-#define GATE_INH_CTRL_0 0xfffe1050
-#define VOLTAGE_CTRL_0 0xfffe1060
-#define TEST_DBG_CTRL_0 0xfffe1070
-
-#define MOD_CONF_CTRL_0 0xfffe1080
-
-#ifdef CONFIG_OMAP1610 /* 1610 Configuration Register */
-
-#define USB_OTG_CTRL 0xFFFB040C
-#define USB_TRANSCEIVER_CTRL 0xFFFE1064
-#define PULL_DWN_CTRL_4 0xFFFE10AC
-#define PU_PD_SEL_0 0xFFFE10B4
-#define PU_PD_SEL_1 0xFFFE10B8
-#define PU_PD_SEL_2 0xFFFE10BC
-#define PU_PD_SEL_3 0xFFFE10C0
-#define PU_PD_SEL_4 0xFFFE10C4
-
-#endif
-/*
- * Traffic Controller Memory Interface Registers
- */
-#define TCMIF_BASE 0xfffecc00
-#define IMIF_PRIO (TCMIF_BASE + 0x00)
-#define EMIFS_PRIO_REG (TCMIF_BASE + 0x04)
-#define EMIFF_PRIO_REG (TCMIF_BASE + 0x08)
-#define EMIFS_CONFIG_REG (TCMIF_BASE + 0x0c)
-#define EMIFS_CS0_CONFIG (TCMIF_BASE + 0x10)
-#define EMIFS_CS1_CONFIG (TCMIF_BASE + 0x14)
-#define EMIFS_CS2_CONFIG (TCMIF_BASE + 0x18)
-#define EMIFS_CS3_CONFIG (TCMIF_BASE + 0x1c)
-#define EMIFF_SDRAM_CONFIG (TCMIF_BASE + 0x20)
-#define EMIFF_MRS (TCMIF_BASE + 0x24)
-#define TC_TIMEOUT1 (TCMIF_BASE + 0x28)
-#define TC_TIMEOUT2 (TCMIF_BASE + 0x2c)
-#define TC_TIMEOUT3 (TCMIF_BASE + 0x30)
-#define TC_ENDIANISM (TCMIF_BASE + 0x34)
-#define EMIFF_SDRAM_CONFIG_2 (TCMIF_BASE + 0x3c)
-#define EMIF_CFG_DYNAMIC_WS (TCMIF_BASE + 0x40)
-
-/*
- * LCD Panel
- */
-#define TI925_LCD_BASE 0xFFFEC000
-#define TI925_LCD_CONTROL (TI925_LCD_BASE)
-#define TI925_LCD_TIMING0 (TI925_LCD_BASE+0x4)
-#define TI925_LCD_TIMING1 (TI925_LCD_BASE+0x8)
-#define TI925_LCD_TIMING2 (TI925_LCD_BASE+0xc)
-#define TI925_LCD_STATUS (TI925_LCD_BASE+0x10)
-#define TI925_LCD_SUBPANEL (TI925_LCD_BASE+0x14)
-
-#define OMAP_LCD_CONTROL TI925_LCD_CONTROL
-
-/* I2C Registers */
-
-#define I2C_BASE 0xfffb3800
-
-#define I2C_REV (I2C_BASE + 0x00)
-#define I2C_IE (I2C_BASE + 0x04)
-#define I2C_STAT (I2C_BASE + 0x08)
-#define I2C_IV (I2C_BASE + 0x0c)
-#define I2C_BUF (I2C_BASE + 0x14)
-#define I2C_CNT (I2C_BASE + 0x18)
-#define I2C_DATA (I2C_BASE + 0x1c)
-#define I2C_CON (I2C_BASE + 0x24)
-#define I2C_OA (I2C_BASE + 0x28)
-#define I2C_SA (I2C_BASE + 0x2c)
-#define I2C_PSC (I2C_BASE + 0x30)
-#define I2C_SCLL (I2C_BASE + 0x34)
-#define I2C_SCLH (I2C_BASE + 0x38)
-#define I2C_SYSTEST (I2C_BASE + 0x3c)
-
-/* I2C masks */
-
-/* I2C Interrupt Enable Register (I2C_IE): */
-
-#define I2C_IE_XRDY_IE (1 << 4) /* Transmit data ready interrupt enable */
-#define I2C_IE_RRDY_IE (1 << 3) /* Receive data ready interrupt enable */
-#define I2C_IE_ARDY_IE (1 << 2) /* Register access ready interrupt enable */
-#define I2C_IE_NACK_IE (1 << 1) /* No acknowledgment interrupt enable */
-#define I2C_IE_AL_IE (1 << 0) /* Arbitration lost interrupt enable */
-
-/* I2C Status Register (I2C_STAT): */
-
-#define I2C_STAT_SBD (1 << 15) /* Single byte data */
-#define I2C_STAT_BB (1 << 12) /* Bus busy */
-#define I2C_STAT_ROVR (1 << 11) /* Receive overrun */
-#define I2C_STAT_XUDF (1 << 10) /* Transmit underflow */
-#define I2C_STAT_AAS (1 << 9) /* Address as slave */
-#define I2C_STAT_AD0 (1 << 8) /* Address zero */
-#define I2C_STAT_XRDY (1 << 4) /* Transmit data ready */
-#define I2C_STAT_RRDY (1 << 3) /* Receive data ready */
-#define I2C_STAT_ARDY (1 << 2) /* Register access ready */
-#define I2C_STAT_NACK (1 << 1) /* No acknowledgment interrupt enable */
-#define I2C_STAT_AL (1 << 0) /* Arbitration lost interrupt enable */
-
-/* I2C Interrupt Vector Register (I2C_IV): */
-
-/* I2C Interrupt Code Register (I2C_INTCODE): */
-
-#define I2C_INTCODE_MASK 7
-#define I2C_INTCODE_NONE 0
-#define I2C_INTCODE_AL 1 /* Arbitration lost */
-#define I2C_INTCODE_NAK 2 /* No acknowledgement/general call */
-#define I2C_INTCODE_ARDY 3 /* Register access ready */
-#define I2C_INTCODE_RRDY 4 /* Rcv data ready */
-#define I2C_INTCODE_XRDY 5 /* Xmit data ready */
-
-/* I2C Buffer Configuration Register (I2C_BUF): */
-
-#define I2C_BUF_RDMA_EN (1 << 15) /* Receive DMA channel enable */
-#define I2C_BUF_XDMA_EN (1 << 7) /* Transmit DMA channel enable */
-
-/* I2C Configuration Register (I2C_CON): */
-
-#define I2C_CON_EN (1 << 15) /* I2C module enable */
-#define I2C_CON_BE (1 << 14) /* Big endian mode */
-#define I2C_CON_STB (1 << 11) /* Start byte mode (master mode only) */
-#define I2C_CON_MST (1 << 10) /* Master/slave mode */
-#define I2C_CON_TRX (1 << 9) /* Transmitter/receiver mode (master mode only) */
-#define I2C_CON_XA (1 << 8) /* Expand address */
-#define I2C_CON_RM (1 << 2) /* Repeat mode (master mode only) */
-#define I2C_CON_STP (1 << 1) /* Stop condition (master mode only) */
-#define I2C_CON_STT (1 << 0) /* Start condition (master mode only) */
-
-/* I2C System Test Register (I2C_SYSTEST): */
-
-#define I2C_SYSTEST_ST_EN (1 << 15) /* System test enable */
-#define I2C_SYSTEST_FREE (1 << 14) /* Free running mode (on breakpoint) */
-#define I2C_SYSTEST_TMODE_MASK (3 << 12) /* Test mode select */
-#define I2C_SYSTEST_TMODE_SHIFT (12) /* Test mode select */
-#define I2C_SYSTEST_SCL_I (1 << 3) /* SCL line sense input value */
-#define I2C_SYSTEST_SCL_O (1 << 2) /* SCL line drive output value */
-#define I2C_SYSTEST_SDA_I (1 << 1) /* SDA line sense input value */
-#define I2C_SYSTEST_SDA_O (1 << 0) /* SDA line drive output value */
-
-/*
- * MMC/SD Host Controller Registers
- */
-
-#define OMAP_MMC_CMD 0xFFFB7800 /* MMC Command */
-#define OMAP_MMC_ARGL 0xFFFB7804 /* MMC argument low */
-#define OMAP_MMC_ARGH 0xFFFB7808 /* MMC argument high */
-#define OMAP_MMC_CON 0xFFFB780C /* MMC system configuration */
-#define OMAP_MMC_STAT 0xFFFB7810 /* MMC status */
-#define OMAP_MMC_IE 0xFFFB7814 /* MMC system interrupt enable */
-#define OMAP_MMC_CTO 0xFFFB7818 /* MMC command time-out */
-#define OMAP_MMC_DTO 0xFFFB781C /* MMC data time-out */
-#define OMAP_MMC_DATA 0xFFFB7820 /* MMC TX/RX FIFO data */
-#define OMAP_MMC_BLEN 0xFFFB7824 /* MMC block length */
-#define OMAP_MMC_NBLK 0xFFFB7828 /* MMC number of blocks */
-#define OMAP_MMC_BUF 0xFFFB782C /* MMC buffer configuration */
-#define OMAP_MMC_SPI 0xFFFB7830 /* MMC serial port interface */
-#define OMAP_MMC_SDIO 0xFFFB7834 /* MMC SDIO mode configuration */
-#define OMAP_MMC_SYST 0xFFFB7838 /* MMC system test */
-#define OMAP_MMC_REV 0xFFFB783C /* MMC module version */
-#define OMAP_MMC_RSP0 0xFFFB7840 /* MMC command response 0 */
-#define OMAP_MMC_RSP1 0xFFFB7844 /* MMC command response 1 */
-#define OMAP_MMC_RSP2 0xFFFB7848 /* MMC command response 2 */
-#define OMAP_MMC_RSP3 0xFFFB784C /* MMC command response 3 */
-#define OMAP_MMC_RSP4 0xFFFB7850 /* MMC command response 4 */
-#define OMAP_MMC_RSP5 0xFFFB7854 /* MMC command response 5 */
-#define OMAP_MMC_RSP6 0xFFFB7858 /* MMC command response 6 */
-#define OMAP_MMC_RSP7 0xFFFB785C /* MMC command response 4 */
-
-/* MMC masks */
-
-#define OMAP_MMC_END_OF_CMD (1 << 0) /* End of command phase */
-#define OMAP_MMC_CARD_BUSY (1 << 2) /* Card enter busy state */
-#define OMAP_MMC_BLOCK_RS (1 << 3) /* Block received/sent */
-#define OMAP_MMC_EOF_BUSY (1 << 4) /* Card exit busy state */
-#define OMAP_MMC_DATA_TIMEOUT (1 << 5) /* Data response time-out */
-#define OMAP_MMC_DATA_CRC (1 << 6) /* Date CRC error */
-#define OMAP_MMC_CMD_TIMEOUT (1 << 7) /* Command response time-out */
-#define OMAP_MMC_CMD_CRC (1 << 8) /* Command CRC error */
-#define OMAP_MMC_A_FULL (1 << 10) /* Buffer almost full */
-#define OMAP_MMC_A_EMPTY (1 << 11) /* Buffer almost empty */
-#define OMAP_MMC_OCR_BUSY (1 << 12) /* OCR busy */
-#define OMAP_MMC_CARD_IRQ (1 << 13) /* Card IRQ received */
-#define OMAP_MMC_CARD_ERR (1 << 14) /* Card status error in response */
-
-/* 2.9.2 MPUI Interface Registers FFFE:C900 */
-
-#define MPUI_CTRL_REG (volatile __u32 *)(0xfffec900)
-#define MPUI_DEBUG_ADDR (volatile __u32 *)(0xfffec904)
-#define MPUI_DEBUG_DATA (volatile __u32 *)(0xfffec908)
-#define MPUI_DEBUG_FLAG (volatile __u16 *)(0xfffec90c)
-#define MPUI_STATUS_REG (volatile __u16 *)(0xfffec910)
-#define MPUI_DSP_STATUS_REG (volatile __u16 *)(0xfffec914)
-#define MPUI_DSP_BOOT_CONFIG (volatile __u16 *)(0xfffec918)
-#define MPUI_DSP_API_CONFIG (volatile __u16 *)(0xfffec91c)
-
-/* 2.9.6 Traffic Controller Memory Interface Registers: */
-#define OMAP_IMIF_PRIO_REG 0xfffecc00
-#define OMAP_EMIFS_PRIO_REG 0xfffecc04
-#define OMAP_EMIFF_PRIO_REG 0xfffecc08
-#define OMAP_EMIFS_CONFIG_REG 0xfffecc0c
-#define OMAP_EMIFS_CS0_CONFIG 0xfffecc10
-#define OMAP_EMIFS_CS1_CONFIG 0xfffecc14
-#define OMAP_EMIFS_CS2_CONFIG 0xfffecc18
-#define OMAP_EMIFS_CS3_CONFIG 0xfffecc1c
-#define OMAP_EMIFF_SDRAM_CONFIG 0xfffecc20
-#define OMAP_EMIFF_MRS 0xfffecc24
-#define OMAP_TIMEOUT1 0xfffecc28
-#define OMAP_TIMEOUT2 0xfffecc2c
-#define OMAP_TIMEOUT3 0xfffecc30
-#define OMAP_ENDIANISM 0xfffecc34
-
-/* 2.9.10 EMIF Slow Interface Configuration Register (EMIFS_CONFIG_REG): */
-#define OMAP_EMIFS_CONFIG_FR (1 << 4)
-#define OMAP_EMIFS_CONFIG_PDE (1 << 3)
-#define OMAP_EMIFS_CONFIG_PWD_EN (1 << 2)
-#define OMAP_EMIFS_CONFIG_BM (1 << 1)
-#define OMAP_EMIFS_CONFIG_WP (1 << 0)
-
-/*
- * Memory chunk set aside for the Framebuffer in SRAM
- */
-#define SRAM_FRAMEBUFFER_MEMORY OMAP1510_SRAM_BASE
-
-
-/*
- * DMA
- */
-
-#define OMAP1510_DMA_BASE 0xFFFED800
-#define OMAP_DMA_BASE OMAP1510_DMA_BASE
-
-/* Global Register selection */
-#define NO_GLOBAL_DMA_ACCESS 0
-
-/* Channel select field
- * NOTE: all other channels are linear, chan0 is 0, chan1 is 1, etc...
- */
-#define LCD_CHANNEL 0xc
-
-/* Register Select Field (LCD) */
-#define DMA_LCD_CTRL 0
-#define DMA_LCD_TOP_F1_L 1
-#define DMA_LCD_TOP_F1_U 2
-#define DMA_LCD_BOT_F1_L 3
-#define DMA_LCD_BOT_F1_U 4
-
-#define LCD_FRAME_MODE (1<<0)
-#define LCD_FRAME_IT_IE (1<<1)
-#define LCD_BUS_ERROR_IT_IE (1<<2)
-#define LCD_FRAME_1_IT_COND (1<<3)
-#define LCD_FRAME_2_IT_COND (1<<4)
-#define LCD_BUS_ERROR_IT_COND (1<<5)
-#define LCD_SOURCE_IMIF (1<<6)
-
-/*
- * Real-Time Clock
- */
-
-#define RTC_SECONDS (volatile __u8 *)(OMAP1510_RTC_BASE + 0x00)
-#define RTC_MINUTES (volatile __u8 *)(OMAP1510_RTC_BASE + 0x04)
-#define RTC_HOURS (volatile __u8 *)(OMAP1510_RTC_BASE + 0x08)
-#define RTC_DAYS (volatile __u8 *)(OMAP1510_RTC_BASE + 0x0C)
-#define RTC_MONTHS (volatile __u8 *)(OMAP1510_RTC_BASE + 0x10)
-#define RTC_YEARS (volatile __u8 *)(OMAP1510_RTC_BASE + 0x14)
-#define RTC_CTRL (volatile __u8 *)(OMAP1510_RTC_BASE + 0x40)
-
-
-/* ---------------------------------------------------------------------------
- * OMAP1510 Interrupt Handlers
- * ---------------------------------------------------------------------------
- *
- */
-#define OMAP_IH1_BASE 0xfffecb00
-#define OMAP_IH2_BASE 0xfffe0000
-#define OMAP1510_ITR 0x0
-#define OMAP1510_MASK 0x4
-
-#define INTERRUPT_HANDLER_BASE OMAP_IH1_BASE
-#define INTERRUPT_INPUT_REGISTER OMAP1510_ITR
-#define INTERRUPT_MASK_REGISTER OMAP1510_MASK
-
-
-/* ---------------------------------------------------------------------------
- * OMAP1510 TIMERS
- * ---------------------------------------------------------------------------
- *
- */
-
-#define OMAP1510_32kHz_TIMER_BASE 0xfffb9000
-
-/* 32k Timer Registers */
-#define TIMER32k_CR 0x08
-#define TIMER32k_TVR 0x00
-#define TIMER32k_TCR 0x04
-
-/* 32k Timer Control Register definition */
-#define TIMER32k_TSS (1<<0)
-#define TIMER32k_TRB (1<<1)
-#define TIMER32k_INT (1<<2)
-#define TIMER32k_ARL (1<<3)
-
-/* MPU Timer base addresses */
-#define OMAP1510_MPUTIMER_BASE 0xfffec500
-#define OMAP1510_MPUTIMER_OFF 0x00000100
-
-#define OMAP1510_TIMER1_BASE 0xfffec500
-#define OMAP1510_TIMER2_BASE 0xfffec600
-#define OMAP1510_TIMER3_BASE 0xfffec700
-
-/* MPU Timer Registers */
-#define CNTL_TIMER 0
-#define LOAD_TIM 4
-#define READ_TIM 8
-
-/* CNTL_TIMER register bits */
-#define MPUTIM_FREE (1<<6)
-#define MPUTIM_CLOCK_ENABLE (1<<5)
-#define MPUTIM_PTV_MASK (0x7<<MPUTIM_PTV_BIT)
-#define MPUTIM_PTV_BIT 2
-#define MPUTIM_AR (1<<1)
-#define MPUTIM_ST (1<<0)
-
-/* ---------------------------------------------------------------------------
- * OMAP1510 GPIO (SHARED)
- * ---------------------------------------------------------------------------
- *
- */
-#define GPIO_DATA_INPUT_REG (OMAP1510_GPIO_BASE + 0x0)
-#define GPIO_DATA_OUTPUT_REG (OMAP1510_GPIO_BASE + 0x4)
-#define GPIO_DIR_CONTROL_REG (OMAP1510_GPIO_BASE + 0x8)
-#define GPIO_INT_CONTROL_REG (OMAP1510_GPIO_BASE + 0xc)
-#define GPIO_INT_MASK_REG (OMAP1510_GPIO_BASE + 0x10)
-#define GPIO_INT_STATUS_REG (OMAP1510_GPIO_BASE + 0x14)
-#define GPIO_PIN_CONTROL_REG (OMAP1510_GPIO_BASE + 0x18)
-
-
-/* ---------------------------
- * OMAP1510 MPUIO (ARM only)
- *----------------------------
- */
-#define OMAP1510_MPUIO_BASE 0xFFFB5000
-#define MPUIO_DATA_INPUT_REG (OMAP1510_MPUIO_BASE + 0x0)
-#define MPUIO_DATA_OUTPUT_REG (OMAP1510_MPUIO_BASE + 0x4)
-#define MPUIO_DIR_CONTROL_REG (OMAP1510_MPUIO_BASE + 0x8)
-
-/* ---------------------------------------------------------------------------
- * OMAP1510 TIPB (only)
- * ---------------------------------------------------------------------------
- *
- */
-#define TIPB_PUBLIC_CNTL_BASE 0xfffed300
-#define MPU_PUBLIC_TIPB_CNTL_REG (TIPB_PUBLIC_CNTL_BASE + 0x8)
-#define TIPB_PRIVATE_CNTL_BASE 0xfffeca00
-#define MPU_PRIVATE_TIPB_CNTL_REG (TIPB_PRIVATE_CNTL_BASE + 0x8)
-
-/*
- * ---------------------------------------------------------------------------
- * OMAP1510 Camera Interface
- * ---------------------------------------------------------------------------
- */
-#define CAMERA_BASE (IO_BASE + 0x6800)
-#define CAM_CTRLCLOCK_REG (CAMERA_BASE + 0x00)
-#define CAM_IT_STATUS_REG (CAMERA_BASE + 0x04)
-#define CAM_MODE_REG (CAMERA_BASE + 0x08)
-#define CAM_STATUS_REG (CAMERA_BASE + 0x0C)
-#define CAM_CAMDATA_REG (CAMERA_BASE + 0x10)
-#define CAM_GPIO_REG (CAMERA_BASE + 0x14)
-#define CAM_PEAK_CTR_REG (CAMERA_BASE + 0x18)
-
-#if 0
-#ifndef __ASSEMBLY__
-typedef struct {
- __u32 ctrlclock;
- __u32 it_status;
- __u32 mode;
- __u32 status;
- __u32 camdata;
- __u32 gpio;
- __u32 peak_counter;
-} camera_regs_t;
-#endif
-#endif
-
-/* CTRLCLOCK bit shifts */
-#define FOSCMOD_BIT 0
-#define FOSCMOD_MASK (0x7 << FOSCMOD_BIT)
-#define FOSCMOD_12MHz 0x0
-#define FOSCMOD_6MHz 0x2
-#define FOSCMOD_9_6MHz 0x4
-#define FOSCMOD_24MHz 0x5
-#define FOSCMOD_8MHz 0x6
-#define POLCLK (1<<3)
-#define CAMEXCLK_EN (1<<4)
-#define MCLK_EN (1<<5)
-#define DPLL_EN (1<<6)
-#define LCLK_EN (1<<7)
-
-/* IT_STATUS bit shifts */
-#define V_UP (1<<0)
-#define V_DOWN (1<<1)
-#define H_UP (1<<2)
-#define H_DOWN (1<<3)
-#define FIFO_FULL (1<<4)
-#define DATA_XFER (1<<5)
-
-/* MODE bit shifts */
-#define CAMOSC (1<<0)
-#define IMGSIZE_BIT 1
-#define IMGSIZE_MASK (0x3 << IMGSIZE_BIT)
-#define IMGSIZE_CIF (0x0 << IMGSIZE_BIT) /* 352x288 */
-#define IMGSIZE_QCIF (0x1 << IMGSIZE_BIT) /* 176x144 */
-#define IMGSIZE_VGA (0x2 << IMGSIZE_BIT) /* 640x480 */
-#define IMGSIZE_QVGA (0x3 << IMGSIZE_BIT) /* 320x240 */
-#define ORDERCAMD (1<<3)
-#define EN_V_UP (1<<4)
-#define EN_V_DOWN (1<<5)
-#define EN_H_UP (1<<6)
-#define EN_H_DOWN (1<<7)
-#define EN_DMA (1<<8)
-#define THRESHOLD (1<<9)
-#define THRESHOLD_BIT 9
-#define THRESHOLD_MASK (0x7f<<9)
-#define EN_NIRQ (1<<16)
-#define EN_FIFO_FULL (1<<17)
-#define RAZ_FIFO (1<<18)
-
-/* STATUS bit shifts */
-#define VSTATUS (1<<0)
-#define HSTATUS (1<<1)
-
-/* GPIO bit shifts */
-#define CAM_RST (1<<0)
-
-
-/*********************
- * Watchdog timer.
- *********************/
-#define WDTIM_BASE 0xfffec800
-#define WDTIM_CONTROL (WDTIM_BASE+0x00)
-#define WDTIM_LOAD (WDTIM_BASE+0x04)
-#define WDTIM_READ (WDTIM_BASE+0x04)
-#define WDTIM_MODE (WDTIM_BASE+0x08)
-
-/* Values to write to mode register to disable the watchdog function. */
-#define DISABLE_SEQ1 0xF5
-#define DISABLE_SEQ2 0xA0
-
-/* WDTIM_CONTROL bit definitions. */
-#define WDTIM_CONTROL_ST BIT7
-
-
-/* ---------------------------------------------------------------------------
- * Differentiating processor versions for those who care.
- * ---------------------------------------------------------------------------
- *
- */
-#define OMAP1509 0
-#define OMAP1510 1
-
-#define OMAP1510_ID_CODE_REG 0xfffed404
-
-#ifndef __ASSEMBLY__
-int cpu_type(void);
-#endif
-
-/*****************************************************************************/
-
-#define CLKGEN_RESET_BASE (0xfffece00)
-#define ARM_CKCTL (volatile __u16 *)(CLKGEN_RESET_BASE + 0x0)
-#define ARM_IDLECT1 (volatile __u16 *)(CLKGEN_RESET_BASE + 0x4)
-#define ARM_IDLECT2 (volatile __u16 *)(CLKGEN_RESET_BASE + 0x8)
-#define ARM_EWUPCT (volatile __u16 *)(CLKGEN_RESET_BASE + 0xC)
-#define ARM_RSTCT1 (volatile __u16 *)(CLKGEN_RESET_BASE + 0x10)
-#define ARM_RSTCT2 (volatile __u16 *)(CLKGEN_RESET_BASE + 0x14)
-#define ARM_SYSST (volatile __u16 *)(CLKGEN_RESET_BASE + 0x18)
-
-
-#define CK_CLKIN 12 /* MHz */
-#define CK_RATEF 1
-#define CK_IDLEF 2
-#define CK_ENABLEF 4
-#define CK_SELECTF 8
-#ifndef __ASSEMBLER__
-#define CK_DPLL1 ((volatile __u16 *)0xfffecf00)
-#else
-#define CK_DPLL1 (0xfffecf00)
-#endif
-#define SETARM_IDLE_SHIFT
-
-/* ARM_CKCTL bit shifts */
-#define PERDIV 0
-#define LCDDIV 2
-#define ARMDIV 4
-#define DSPDIV 6
-#define TCDIV 8
-#define DSPMMUDIV 10
-#define ARM_TIMXO 12
-#define EN_DSPCK 13
-#define ARM_INTHCK_SEL 14 /* REVISIT -- where is this used? */
-
-#define ARM_CKCTL_RSRVD_BIT15 (1 << 15)
-#define ARM_CKCTL_ARM_INTHCK_SEL (1 << 14)
-#define ARM_CKCTL_EN_DSPCK (1 << 13)
-#define ARM_CKCTL_ARM_TIMXO (1 << 12)
-#define ARM_CKCTL_DSPMMU_DIV1 (1 << 11)
-#define ARM_CKCTL_DSPMMU_DIV2 (1 << 10)
-#define ARM_CKCTL_TCDIV1 (1 << 9)
-#define ARM_CKCTL_TCDIV2 (1 << 8)
-#define ARM_CKCTL_DSPDIV1 (1 << 7)
-#define ARM_CKCTL_DSPDIV0 (1 << 6)
-#define ARM_CKCTL_ARMDIV1 (1 << 5)
-#define ARM_CKCTL_ARMDIV0 (1 << 4)
-#define ARM_CKCTL_LCDDIV1 (1 << 3)
-#define ARM_CKCTL_LCDDIV0 (1 << 2)
-#define ARM_CKCTL_PERDIV1 (1 << 1)
-#define ARM_CKCTL_PERDIV0 (1 << 0)
-
-/* ARM_IDLECT1 bit shifts */
-#define IDLWDT_ARM 0
-#define IDLXORP_ARM 1
-#define IDLPER_ARM 2
-#define IDLLCD_ARM 3
-#define IDLLB_ARM 4
-#define IDLHSAB_ARM 5
-#define IDLIF_ARM 6
-#define IDLDPLL_ARM 7
-#define IDLAPI_ARM 8
-#define IDLTIM_ARM 9
-#define SETARM_IDLE 11
-
-/* ARM_IDLECT2 bit shifts */
-#define EN_WDTCK 0
-#define EN_XORPCK 1
-#define EN_PERCK 2
-#define EN_LCDCK 3
-#define EN_LBCK 4
-#define EN_HSABCK 5
-#define EN_APICK 6
-#define EN_TIMCK 7
-#define DMACK_REQ 8
-#define EN_GPIOCK 9
-#define EN_LBFREECK 10
-
-#define ARM_RSTCT1_SW_RST (1 << 3)
-#define ARM_RSTCT1_DSP_RST (1 << 2)
-#define ARM_RSTCT1_DSP_EN (1 << 1)
-#define ARM_RSTCT1_ARM_RST (1 << 0)
-
-/* ARM_RSTCT2 bit shifts */
-#define EN_PER 0
-
-#define ARM_SYSST_RSRVD_BIT15 (1 << 15)
-#define ARM_SYSST_RSRVD_BIT14 (1 << 14)
-#define ARM_SYSST_CLOCK_SELECT2 (1 << 13)
-#define ARM_SYSST_CLOCK_SELECT1 (1 << 12)
-#define ARM_SYSST_CLOCK_SELECT0 (1 << 11)
-#define ARM_SYSST_RSRVD_BIT10 (1 << 10)
-#define ARM_SYSST_RSRVD_BIT9 (1 << 9)
-#define ARM_SYSST_RSRVD_BIT8 (1 << 8)
-#define ARM_SYSST_RSRVD_BIT7 (1 << 7)
-#define ARM_SYSST_IDLE_DSP (1 << 6)
-#define ARM_SYSST_POR (1 << 5)
-#define ARM_SYSST_EXT_RST (1 << 4)
-#define ARM_SYSST_ARM_MCRST (1 << 3)
-#define ARM_SYSST_ARM_WDRST (1 << 2)
-#define ARM_SYSST_GLOB_SWRST (1 << 1)
-#define ARM_SYSST_DSP_WDRST (1 << 0)
-
-/* Table 15-23. DPLL Control Registers: */
-#define DPLL_CTL_REG (volatile __u16 *)(0xfffecf00)
-
-/* Table 15-24. Control Register (CTL_REG): */
-
-#define DPLL_CTL_REG_IOB (1 << 13)
-#define DPLL_CTL_REG_PLL_MULT Fld(5,0)
-
-/*****************************************************************************/
-
-/* OMAP INTERRUPT REGISTERS */
-#define IRQ_ITR 0x00
-#define IRQ_MIR 0x04
-#define IRQ_SIR_IRQ 0x10
-#define IRQ_SIR_FIQ 0x14
-#define IRQ_CONTROL_REG 0x18
-#define IRQ_ISR 0x9c
-#define IRQ_ILR0 0x1c
-
-#define REG_IHL1_MIR (OMAP_IH1_BASE+IRQ_MIR)
-#define REG_IHL2_MIR (OMAP_IH2_BASE+IRQ_MIR)
-
-/* INTERRUPT LEVEL REGISTER BITS */
-#define ILR_PRIORITY_MASK (0x3c)
-#define ILR_PRIORITY_SHIFT (2)
-#define ILR_LEVEL_TRIGGER (1<<1)
-#define ILR_FIQ (1<<0)
-
-#define IRQ_LEVEL_INT 1
-#define IRQ_EDGE_INT 0
-
-/* Macros to access registers */
-#define outb(v,p) *(volatile u8 *) (p) = v
-#define outw(v,p) *(volatile u16 *) (p) = v
-#define outl(v,p) *(volatile u32 *) (p) = v
-
-#define inb(p) *(volatile u8 *) (p)
-#define inw(p) *(volatile u16 *) (p)
-#define inl(p) *(volatile u32 *) (p)
+++ /dev/null
-/*
- * (C) Copyright 2003
- * Texas Instruments.
- * Kshitij Gupta <kshitij@ti.com>
- * Configuation settings for the TI OMAP Innovator board.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-#define CONFIG_ARM926EJS 1 /* This is an arm926ejs CPU core */
-#define CONFIG_OMAP 1 /* in a TI OMAP core */
-#define CONFIG_OMAP1610 1 /* 5912 is same as 1610 */
-#define CONFIG_OSK_OMAP5912 1 /* a OSK Board */
-
-#define CONFIG_DISPLAY_CPUINFO 1 /* display cpu info (and speed) */
-#define CONFIG_DISPLAY_BOARDINFO 1 /* display board info */
-
-/* input clock of PLL */
-/* the OMAP5912 OSK has 12MHz input clock */
-#define CONFIG_SYS_CLK_FREQ 12000000
-
-#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS 1
-#define CONFIG_INITRD_TAG 1 /* Required for ramdisk support */
-
-/*
- * Size of malloc() pool
- */
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024)
-
-/*
- * Hardware drivers
- */
-/*
-*/
-#define CONFIG_LAN91C96
-#define CONFIG_LAN91C96_BASE 0x04800300
-#define CONFIG_LAN91C96_EXT_PHY
-
-/*
- * NS16550 Configuration
- */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE (-4)
-#define CONFIG_SYS_NS16550_CLK (48000000) /* can be 12M/32Khz or 48Mhz */
-#define CONFIG_SYS_NS16550_COM1 0xfffb0000 /* uart1, bluetooth uart
- on helen */
-
-/*
- * select serial console configuration
- */
-#define CONFIG_SERIAL1 1 /* we use SERIAL 1 on OMAP5912 OSK */
-
-/* allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_BAUDRATE 115200
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_DHCP
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-
-
-#include <configs/omap1510.h>
-
-#define CONFIG_BOOTDELAY 3
-#define CONFIG_BOOTARGS "mem=32M console=ttyS0,115200n8 noinitrd \
- root=/dev/nfs rw nfsroot=157.87.82.48:\
- /home/mwd/myfs/target ip=dhcp"
-#define CONFIG_NETMASK 255.255.254.0 /* talk on MY local net */
-#define CONFIG_IPADDR 156.117.97.156 /* static IP I currently own */
-#define CONFIG_SERVERIP 156.117.97.139 /* current IP of my dev pc */
-#define CONFIG_BOOTFILE "uImage" /* file to load */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port */
-#endif
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_PROMPT "OMAP5912 OSK # " /* Monitor Command Prompt */
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x10000000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x12000000 /* 32 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x10000000 /* default load address */
-
-/* The 1610 has 6 timers, they can be driven by the RefClk (12Mhz) or by
- * DPLL1. This time is further subdivided by a local divisor.
- */
-#define CONFIG_SYS_TIMERBASE 0xFFFEC500 /* use timer 1 */
-#define CONFIG_SYS_PTV 7 /* 2^(PTV+1), divide by 256 */
-
-/*-----------------------------------------------------------------------
- * Physical Memory Map
- */
-#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */
-#define PHYS_SDRAM_1 0x10000000 /* SDRAM Bank #1 */
-#define PHYS_SDRAM_1_SIZE 0x02000000 /* 32 MB */
-
-#define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */
-#define PHYS_FLASH_2 0x01000000 /* Flash Bank #2 */
-
-#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE /* Monitor at beginning of flash */
-
-#define PHYS_SRAM 0x20000000
-
-/*-----------------------------------------------------------------------
- * FLASH driver setup
- */
-#define CONFIG_SYS_FLASH_CFI 1 /* Flash memory is CFI compliant */
-#define CONFIG_FLASH_CFI_DRIVER 1 /* Use drivers/mtd/cfi_flash.c */
-
-#define CONFIG_SYS_FLASH_BANKS_LIST { PHYS_FLASH_1, PHYS_FLASH_2 }
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */
-#define PHYS_FLASH_SIZE 0x02000000 /* 32MB */
-#define CONFIG_SYS_MAX_FLASH_SECT (259) /* max number of sectors on one chip */
-
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* Use buffered writes (~10x faster) */
-#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use hardware sector protection */
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
-
-/* timeout values are in ticks */
-#define CONFIG_SYS_FLASH_ERASE_TOUT (20*CONFIG_SYS_HZ) /* Timeout for Flash Erase */
-#define CONFIG_SYS_FLASH_WRITE_TOUT (20*CONFIG_SYS_HZ) /* Timeout for Flash Write */
-
-/*-----------------------------------------------------------------------
- * FLASH and environment organization
- */
-#define CONFIG_ENV_IS_IN_FLASH 1
-/* addr of environment */
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET)
-
-#define CONFIG_ENV_SIZE 0x20000 /* Total Size of Environment Sector */
-#define CONFIG_ENV_OFFSET 0x40000 /* environment starts here */
-
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
-#define CONFIG_SYS_INIT_RAM_ADDR PHYS_SRAM
-#define CONFIG_SYS_INIT_RAM_SIZE (250 * 1024)
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
- CONFIG_SYS_INIT_RAM_SIZE)
-
-#endif /* __CONFIG_H */
projects / karo-tx-uboot.git / commitdiff