void reset_cpu(unsigned long a)
{
struct davinci_timer *const wdttimer =
- (struct davinci_timer *)DAVINCI_TIMER1_BASE;
+ (struct davinci_timer *)DAVINCI_WDOG_BASE;
writel(0x08, &wdttimer->tgcr);
writel(readl(&wdttimer->tgcr) | 0x03, &wdttimer->tgcr);
writel(0, &wdttimer->tim12);
COBJS += clock.o
COBJS += sys_info.o
+COBJS += mem.o
COBJS += ddr.o
COBJS += emif4.o
COBJS += board.o
COBJS += mux.o
+COBJS-$(CONFIG_NAND_OMAP_GPMC) += elm.o
SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(COBJS) $(COBJS-y) $(SOBJS))
#include <asm/arch/ddr_defs.h>
#include <asm/arch/clock.h>
#include <asm/arch/gpio.h>
+#include <asm/arch/mem.h>
#include <asm/arch/mmc_host_def.h>
#include <asm/arch/sys_proto.h>
#include <asm/io.h>
;
#endif /* CONFIG_SERIAL6 */
+ /* GPMC */
+ writel(PRCM_MOD_EN, &cmper->gpmcclkctrl);
+ while (readl(&cmper->gpmcclkctrl) != PRCM_MOD_EN)
+ ;
+
+ /* ELM */
+ writel(PRCM_MOD_EN, &cmper->elmclkctrl);
+ while (readl(&cmper->elmclkctrl) != PRCM_MOD_EN)
+ ;
+
/* MMC0*/
writel(PRCM_MOD_EN, &cmper->mmc0clkctrl);
while (readl(&cmper->mmc0clkctrl) != PRCM_MOD_EN)
--- /dev/null
+/*
+ * (C) Copyright 2010-2011 Texas Instruments, <www.ti.com>
+ * Mansoor Ahamed <mansoor.ahamed@ti.com>
+ *
+ * BCH Error Location Module (ELM) support.
+ *
+ * NOTE:
+ * 1. Supports only continuous mode. Dont see need for page mode in uboot
+ * 2. Supports only syndrome polynomial 0. i.e. poly local variable is
+ * always set to ELM_DEFAULT_POLY. Dont see need for other polynomial
+ * sets in uboot
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/errno.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/omap_gpmc.h>
+#include <asm/arch/elm.h>
+
+#define ELM_DEFAULT_POLY (0)
+
+struct elm *elm_cfg;
+
+/**
+ * elm_load_syndromes - Load BCH syndromes based on nibble selection
+ * @syndrome: BCH syndrome
+ * @nibbles:
+ * @poly: Syndrome Polynomial set to use
+ *
+ * Load BCH syndromes based on nibble selection
+ */
+static void elm_load_syndromes(u8 *syndrome, u32 nibbles, u8 poly)
+{
+ u32 *ptr;
+ u32 val;
+
+ /* reg 0 */
+ ptr = &elm_cfg->syndrome_fragments[poly].syndrome_fragment_x[0];
+ val = syndrome[0] | (syndrome[1] << 8) | (syndrome[2] << 16) |
+ (syndrome[3] << 24);
+ writel(val, ptr);
+ /* reg 1 */
+ ptr = &elm_cfg->syndrome_fragments[poly].syndrome_fragment_x[1];
+ val = syndrome[4] | (syndrome[5] << 8) | (syndrome[6] << 16) |
+ (syndrome[7] << 24);
+ writel(val, ptr);
+
+ /* BCH 8-bit with 26 nibbles (4*8=32) */
+ if (nibbles > 13) {
+ /* reg 2 */
+ ptr = &elm_cfg->syndrome_fragments[poly].syndrome_fragment_x[2];
+ val = syndrome[8] | (syndrome[9] << 8) | (syndrome[10] << 16) |
+ (syndrome[11] << 24);
+ writel(val, ptr);
+ /* reg 3 */
+ ptr = &elm_cfg->syndrome_fragments[poly].syndrome_fragment_x[3];
+ val = syndrome[12] | (syndrome[13] << 8) |
+ (syndrome[14] << 16) | (syndrome[15] << 24);
+ writel(val, ptr);
+ }
+
+ /* BCH 16-bit with 52 nibbles (7*8=56) */
+ if (nibbles > 26) {
+ /* reg 4 */
+ ptr = &elm_cfg->syndrome_fragments[poly].syndrome_fragment_x[4];
+ val = syndrome[16] | (syndrome[17] << 8) |
+ (syndrome[18] << 16) | (syndrome[19] << 24);
+ writel(val, ptr);
+
+ /* reg 5 */
+ ptr = &elm_cfg->syndrome_fragments[poly].syndrome_fragment_x[5];
+ val = syndrome[20] | (syndrome[21] << 8) |
+ (syndrome[22] << 16) | (syndrome[23] << 24);
+ writel(val, ptr);
+
+ /* reg 6 */
+ ptr = &elm_cfg->syndrome_fragments[poly].syndrome_fragment_x[6];
+ val = syndrome[24] | (syndrome[25] << 8) |
+ (syndrome[26] << 16) | (syndrome[27] << 24);
+ writel(val, ptr);
+ }
+}
+
+/**
+ * elm_check_errors - Check for BCH errors and return error locations
+ * @syndrome: BCH syndrome
+ * @nibbles:
+ * @error_count: Returns number of errrors in the syndrome
+ * @error_locations: Returns error locations (in decimal) in this array
+ *
+ * Check the provided syndrome for BCH errors and return error count
+ * and locations in the array passed. Returns -1 if error is not correctable,
+ * else returns 0
+ */
+int elm_check_error(u8 *syndrome, u32 nibbles, u32 *error_count,
+ u32 *error_locations)
+{
+ u8 poly = ELM_DEFAULT_POLY;
+ s8 i;
+ u32 location_status;
+
+ elm_load_syndromes(syndrome, nibbles, poly);
+
+ /* start processing */
+ writel((readl(&elm_cfg->syndrome_fragments[poly].syndrome_fragment_x[6])
+ | ELM_SYNDROME_FRAGMENT_6_SYNDROME_VALID),
+ &elm_cfg->syndrome_fragments[poly].syndrome_fragment_x[6]);
+
+ /* wait for processing to complete */
+ while ((readl(&elm_cfg->irqstatus) & (0x1 << poly)) != 0x1)
+ ;
+ /* clear status */
+ writel((readl(&elm_cfg->irqstatus) | (0x1 << poly)),
+ &elm_cfg->irqstatus);
+
+ /* check if correctable */
+ location_status = readl(&elm_cfg->error_location[poly].location_status);
+ if (!(location_status & ELM_LOCATION_STATUS_ECC_CORRECTABLE_MASK))
+ return -1;
+
+ /* get error count */
+ *error_count = readl(&elm_cfg->error_location[poly].location_status) &
+ ELM_LOCATION_STATUS_ECC_NB_ERRORS_MASK;
+
+ for (i = 0; i < *error_count; i++) {
+ error_locations[i] =
+ readl(&elm_cfg->error_location[poly].error_location_x[i]);
+ }
+
+ return 0;
+}
+
+
+/**
+ * elm_config - Configure ELM module
+ * @level: 4 / 8 / 16 bit BCH
+ *
+ * Configure ELM module based on BCH level.
+ * Set mode as continuous mode.
+ * Currently we are using only syndrome 0 and syndromes 1 to 6 are not used.
+ * Also, the mode is set only for syndrome 0
+ */
+int elm_config(enum bch_level level)
+{
+ u32 val;
+ u8 poly = ELM_DEFAULT_POLY;
+ u32 buffer_size = 0x7FF;
+
+ /* config size and level */
+ val = (u32)(level) & ELM_LOCATION_CONFIG_ECC_BCH_LEVEL_MASK;
+ val |= ((buffer_size << ELM_LOCATION_CONFIG_ECC_SIZE_POS) &
+ ELM_LOCATION_CONFIG_ECC_SIZE_MASK);
+ writel(val, &elm_cfg->location_config);
+
+ /* config continous mode */
+ /* enable interrupt generation for syndrome polynomial set */
+ writel((readl(&elm_cfg->irqenable) | (0x1 << poly)),
+ &elm_cfg->irqenable);
+ /* set continuous mode for the syndrome polynomial set */
+ writel((readl(&elm_cfg->page_ctrl) & ~(0x1 << poly)),
+ &elm_cfg->page_ctrl);
+
+ return 0;
+}
+
+/**
+ * elm_reset - Do a soft reset of ELM
+ *
+ * Perform a soft reset of ELM and return after reset is done.
+ */
+void elm_reset(void)
+{
+ /* initiate reset */
+ writel((readl(&elm_cfg->sysconfig) | ELM_SYSCONFIG_SOFTRESET),
+ &elm_cfg->sysconfig);
+
+ /* wait for reset complete and normal operation */
+ while ((readl(&elm_cfg->sysstatus) & ELM_SYSSTATUS_RESETDONE) !=
+ ELM_SYSSTATUS_RESETDONE)
+ ;
+}
+
+/**
+ * elm_init - Initialize ELM module
+ *
+ * Initialize ELM support. Currently it does only base address init
+ * and ELM reset.
+ */
+void elm_init(void)
+{
+ elm_cfg = (struct elm *)ELM_BASE;
+ elm_reset();
+}
--- /dev/null
+/*
+ * (C) Copyright 2010
+ * Texas Instruments, <www.ti.com>
+ *
+ * Author :
+ * Mansoor Ahamed <mansoor.ahamed@ti.com>
+ *
+ * Initial Code from:
+ * Manikandan Pillai <mani.pillai@ti.com>
+ * Richard Woodruff <r-woodruff2@ti.com>
+ * Syed Mohammed Khasim <khasim@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/mem.h>
+#include <asm/arch/sys_proto.h>
+#include <command.h>
+
+struct gpmc *gpmc_cfg;
+
+#if defined(CONFIG_CMD_NAND)
+static const u32 gpmc_m_nand[GPMC_MAX_REG] = {
+ M_NAND_GPMC_CONFIG1,
+ M_NAND_GPMC_CONFIG2,
+ M_NAND_GPMC_CONFIG3,
+ M_NAND_GPMC_CONFIG4,
+ M_NAND_GPMC_CONFIG5,
+ M_NAND_GPMC_CONFIG6, 0
+};
+#endif
+
+
+void enable_gpmc_cs_config(const u32 *gpmc_config, struct gpmc_cs *cs, u32 base,
+ u32 size)
+{
+ writel(0, &cs->config7);
+ sdelay(1000);
+ /* Delay for settling */
+ writel(gpmc_config[0], &cs->config1);
+ writel(gpmc_config[1], &cs->config2);
+ writel(gpmc_config[2], &cs->config3);
+ writel(gpmc_config[3], &cs->config4);
+ writel(gpmc_config[4], &cs->config5);
+ writel(gpmc_config[5], &cs->config6);
+ /* Enable the config */
+ writel((((size & 0xF) << 8) | ((base >> 24) & 0x3F) |
+ (1 << 6)), &cs->config7);
+ sdelay(2000);
+}
+
+/*****************************************************
+ * gpmc_init(): init gpmc bus
+ * Init GPMC for x16, MuxMode (SDRAM in x32).
+ * This code can only be executed from SRAM or SDRAM.
+ *****************************************************/
+void gpmc_init(void)
+{
+ /* putting a blanket check on GPMC based on ZeBu for now */
+ gpmc_cfg = (struct gpmc *)GPMC_BASE;
+
+#ifdef CONFIG_CMD_NAND
+ const u32 *gpmc_config = NULL;
+ u32 base = 0;
+ u32 size = 0;
+#endif
+ /* global settings */
+ writel(0x00000008, &gpmc_cfg->sysconfig);
+ writel(0x00000100, &gpmc_cfg->irqstatus);
+ writel(0x00000200, &gpmc_cfg->irqenable);
+ writel(0x00000012, &gpmc_cfg->config);
+ /*
+ * Disable the GPMC0 config set by ROM code
+ */
+ writel(0, &gpmc_cfg->cs[0].config7);
+ sdelay(1000);
+
+#ifdef CONFIG_CMD_NAND
+ gpmc_config = gpmc_m_nand;
+
+ base = PISMO1_NAND_BASE;
+ size = PISMO1_NAND_SIZE;
+ enable_gpmc_cs_config(gpmc_config, &gpmc_cfg->cs[0], base, size);
+#endif
+}
LIB = $(obj)libomap-common.o
-SOBJS := reset.o
-
-COBJS := timer.o
+COBJS := reset.o
+COBJS += timer.o
COBJS += utils.o
ifneq ($(CONFIG_OMAP44XX)$(CONFIG_OMAP54XX),)
#include <asm/omap_common.h>
#include <asm/arch/omap.h>
#include <asm/arch/mmc_host_def.h>
+#include <asm/arch/sys_proto.h>
/*
* This is used to verify if the configuration header
#include <asm/utils.h>
#include <linux/compiler.h>
+static int emif1_enabled = -1, emif2_enabled = -1;
+
void set_lpmode_selfrefresh(u32 base)
{
struct emif_reg_struct *emif = (struct emif_reg_struct *)base;
void dmm_init(u32 base)
{
const struct dmm_lisa_map_regs *lisa_map_regs;
+ u32 i, section, valid;
#ifdef CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS
emif_get_dmm_regs(&lisa_map_regs);
writel(lisa_map_regs->dmm_lisa_map_0,
&hw_lisa_map_regs->dmm_lisa_map_0);
}
+
+ /*
+ * EMIF should be configured only when
+ * memory is mapped on it. Using emif1_enabled
+ * and emif2_enabled variables for this.
+ */
+ emif1_enabled = 0;
+ emif2_enabled = 0;
+ for (i = 0; i < 4; i++) {
+ section = __raw_readl(DMM_BASE + i*4);
+ valid = (section & EMIF_SDRC_MAP_MASK) >>
+ (EMIF_SDRC_MAP_SHIFT);
+ if (valid == 3) {
+ emif1_enabled = 1;
+ emif2_enabled = 1;
+ break;
+ } else if (valid == 1) {
+ emif1_enabled = 1;
+ } else if (valid == 2) {
+ emif2_enabled = 1;
+ }
+ }
+
}
/*
writel(CM_DLL_CTRL_NO_OVERRIDE, &prcm->cm_dll_ctrl);
}
- do_sdram_init(EMIF1_BASE);
- do_sdram_init(EMIF2_BASE);
-
if (!in_sdram)
dmm_init(DMM_BASE);
+ if (emif1_enabled)
+ do_sdram_init(EMIF1_BASE);
+
+ if (emif2_enabled)
+ do_sdram_init(EMIF2_BASE);
+
if (!(in_sdram || warm_reset())) {
- emif_post_init_config(EMIF1_BASE);
- emif_post_init_config(EMIF2_BASE);
+ if (emif1_enabled)
+ emif_post_init_config(EMIF1_BASE);
+ if (emif2_enabled)
+ emif_post_init_config(EMIF2_BASE);
}
/* for the shadow registers to take effect */
*/
omap3_update_aux_cr(0, 0x2);
}
-#endif
+#endif /* !CONFIG_SYS_L2CACHE_OFF */
#ifndef CONFIG_SYS_DCACHE_OFF
void enable_caches(void)
/* Enable D-cache. I-cache is already enabled in start.S */
dcache_enable();
}
-#endif
+#endif /* !CONFIG_SYS_DCACHE_OFF */
M_NAND_GPMC_CONFIG5,
M_NAND_GPMC_CONFIG6, 0
};
-
-#if defined(CONFIG_ENV_IS_IN_NAND)
-#define GPMC_CS 0
-#else
-#define GPMC_CS 1
-#endif
-
-#endif
+#endif /* CONFIG_CMD_NAND */
#if defined(CONFIG_CMD_ONENAND)
static const u32 gpmc_onenand[GPMC_MAX_REG] = {
ONENAND_GPMC_CONFIG5,
ONENAND_GPMC_CONFIG6, 0
};
-
-#if defined(CONFIG_ENV_IS_IN_ONENAND)
-#define GPMC_CS 0
-#else
-#define GPMC_CS 1
-#endif
-
-#endif
+#endif /* CONFIG_CMD_ONENAND */
/********************************************************
* mem_ok() - test used to see if timings are correct
* - Test CS to make sure it's OK for use
*/
static void write_sdrc_timings(u32 cs, struct sdrc_actim *sdrc_actim_base,
- u32 mcfg, u32 ctrla, u32 ctrlb, u32 rfr_ctrl, u32 mr)
+ struct board_sdrc_timings *timings)
{
/* Setup timings we got from the board. */
- writel(mcfg, &sdrc_base->cs[cs].mcfg);
- writel(ctrla, &sdrc_actim_base->ctrla);
- writel(ctrlb, &sdrc_actim_base->ctrlb);
- writel(rfr_ctrl, &sdrc_base->cs[cs].rfr_ctrl);
+ writel(timings->mcfg, &sdrc_base->cs[cs].mcfg);
+ writel(timings->ctrla, &sdrc_actim_base->ctrla);
+ writel(timings->ctrlb, &sdrc_actim_base->ctrlb);
+ writel(timings->rfr_ctrl, &sdrc_base->cs[cs].rfr_ctrl);
writel(CMD_NOP, &sdrc_base->cs[cs].manual);
writel(CMD_PRECHARGE, &sdrc_base->cs[cs].manual);
writel(CMD_AUTOREFRESH, &sdrc_base->cs[cs].manual);
writel(CMD_AUTOREFRESH, &sdrc_base->cs[cs].manual);
- writel(mr, &sdrc_base->cs[cs].mr);
+ writel(timings->mr, &sdrc_base->cs[cs].mr);
/*
* Test ram in this bank
void do_sdrc_init(u32 cs, u32 early)
{
struct sdrc_actim *sdrc_actim_base0, *sdrc_actim_base1;
- u32 mcfg, ctrla, ctrlb, rfr_ctrl, mr;
+ struct board_sdrc_timings timings;
sdrc_actim_base0 = (struct sdrc_actim *)SDRC_ACTIM_CTRL0_BASE;
sdrc_actim_base1 = (struct sdrc_actim *)SDRC_ACTIM_CTRL1_BASE;
* setup CS1.
*/
#ifdef CONFIG_SPL_BUILD
- get_board_mem_timings(&mcfg, &ctrla, &ctrlb, &rfr_ctrl, &mr);
+ get_board_mem_timings(&timings);
#endif
if (early) {
/* reset sdrc controller */
writel(ENADLL | DLLPHASE_90, &sdrc_base->dlla_ctrl);
sdelay(0x20000);
#ifdef CONFIG_SPL_BUILD
- write_sdrc_timings(CS0, sdrc_actim_base0, mcfg, ctrla, ctrlb,
- rfr_ctrl, mr);
+ write_sdrc_timings(CS0, sdrc_actim_base0, &timings);
make_cs1_contiguous();
- write_sdrc_timings(CS1, sdrc_actim_base1, mcfg, ctrla, ctrlb,
- rfr_ctrl, mr);
+ write_sdrc_timings(CS1, sdrc_actim_base1, &timings);
#endif
}
* so we may be asked now to setup CS1.
*/
if (cs == CS1) {
- mcfg = readl(&sdrc_base->cs[CS0].mcfg),
- rfr_ctrl = readl(&sdrc_base->cs[CS0].rfr_ctrl);
- ctrla = readl(&sdrc_actim_base0->ctrla),
- ctrlb = readl(&sdrc_actim_base0->ctrlb);
- mr = readl(&sdrc_base->cs[CS0].mr);
- write_sdrc_timings(cs, sdrc_actim_base1, mcfg, ctrla, ctrlb,
- rfr_ctrl, mr);
-
+ timings.mcfg = readl(&sdrc_base->cs[CS0].mcfg),
+ timings.rfr_ctrl = readl(&sdrc_base->cs[CS0].rfr_ctrl);
+ timings.ctrla = readl(&sdrc_actim_base0->ctrla);
+ timings.ctrlb = readl(&sdrc_actim_base0->ctrlb);
+ timings.mr = readl(&sdrc_base->cs[CS0].mr);
+ write_sdrc_timings(cs, sdrc_actim_base1, &timings);
}
}
*/
#define printf(fmt, args...)
#define puts(s)
-#endif
+#endif /* !CONFIG_SPL_BUILD */
struct omap4_prcm_regs *const prcm = (struct omap4_prcm_regs *)0x4A004100;
if ((omap4_rev < OMAP4460_ES1_0) || !readl(&ctrl->control_efuse_2))
writel(CONTROL_EFUSE_2_OVERRIDE, &ctrl->control_efuse_2);
}
-#endif
+#endif /* CONFIG_SPL_BUILD */
/* dummy fuction for omap4 */
void config_data_eye_leveling_samples(u32 emif_base)
{
set_pl310_ctrl_reg(0);
}
-#endif
+#endif /* !CONFIG_SYS_L2CACHE_OFF */
#ifndef __KERNEL_STRICT_NAMES
#ifndef __ASSEMBLY__
+struct gpmc_cs {
+ u32 config1; /* 0x00 */
+ u32 config2; /* 0x04 */
+ u32 config3; /* 0x08 */
+ u32 config4; /* 0x0C */
+ u32 config5; /* 0x10 */
+ u32 config6; /* 0x14 */
+ u32 config7; /* 0x18 */
+ u32 nand_cmd; /* 0x1C */
+ u32 nand_adr; /* 0x20 */
+ u32 nand_dat; /* 0x24 */
+ u8 res[8]; /* blow up to 0x30 byte */
+};
+
+struct bch_res_0_3 {
+ u32 bch_result_x[4];
+};
+
+struct gpmc {
+ u8 res1[0x10];
+ u32 sysconfig; /* 0x10 */
+ u8 res2[0x4];
+ u32 irqstatus; /* 0x18 */
+ u32 irqenable; /* 0x1C */
+ u8 res3[0x20];
+ u32 timeout_control; /* 0x40 */
+ u8 res4[0xC];
+ u32 config; /* 0x50 */
+ u32 status; /* 0x54 */
+ u8 res5[0x8]; /* 0x58 */
+ struct gpmc_cs cs[8]; /* 0x60, 0x90, .. */
+ u8 res6[0x14]; /* 0x1E0 */
+ u32 ecc_config; /* 0x1F4 */
+ u32 ecc_control; /* 0x1F8 */
+ u32 ecc_size_config; /* 0x1FC */
+ u32 ecc1_result; /* 0x200 */
+ u32 ecc2_result; /* 0x204 */
+ u32 ecc3_result; /* 0x208 */
+ u32 ecc4_result; /* 0x20C */
+ u32 ecc5_result; /* 0x210 */
+ u32 ecc6_result; /* 0x214 */
+ u32 ecc7_result; /* 0x218 */
+ u32 ecc8_result; /* 0x21C */
+ u32 ecc9_result; /* 0x220 */
+ u8 res7[12]; /* 0x224 */
+ u32 testmomde_ctrl; /* 0x230 */
+ u8 res8[12]; /* 0x234 */
+ struct bch_res_0_3 bch_result_0_3[2]; /* 0x240 */
+};
+
+/* Used for board specific gpmc initialization */
+extern struct gpmc *gpmc_cfg;
+
/* Encapsulating core pll registers */
struct cm_wkuppll {
unsigned int wkclkstctrl; /* offset 0x00 */
--- /dev/null
+/*
+ * (C) Copyright 2010-2011 Texas Instruments, <www.ti.com>
+ * Mansoor Ahamed <mansoor.ahamed@ti.com>
+ *
+ * Derived from work done by Rohit Choraria <rohitkc@ti.com> for omap3
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#ifndef __ASM_ARCH_ELM_H
+#define __ASM_ARCH_ELM_H
+/*
+ * ELM Module Registers
+ */
+
+/* ELM registers bit fields */
+#define ELM_SYSCONFIG_SOFTRESET_MASK (0x2)
+#define ELM_SYSCONFIG_SOFTRESET (0x2)
+#define ELM_SYSSTATUS_RESETDONE_MASK (0x1)
+#define ELM_SYSSTATUS_RESETDONE (0x1)
+#define ELM_LOCATION_CONFIG_ECC_BCH_LEVEL_MASK (0x3)
+#define ELM_LOCATION_CONFIG_ECC_SIZE_MASK (0x7FF0000)
+#define ELM_LOCATION_CONFIG_ECC_SIZE_POS (16)
+#define ELM_SYNDROME_FRAGMENT_6_SYNDROME_VALID (0x00010000)
+#define ELM_LOCATION_STATUS_ECC_CORRECTABLE_MASK (0x100)
+#define ELM_LOCATION_STATUS_ECC_NB_ERRORS_MASK (0x1F)
+
+#ifndef __ASSEMBLY__
+
+enum bch_level {
+ BCH_4_BIT = 0,
+ BCH_8_BIT,
+ BCH_16_BIT
+};
+
+
+/* BCH syndrome registers */
+struct syndrome {
+ u32 syndrome_fragment_x[7]; /* 0x400, 0x404.... 0x418 */
+ u8 res1[36]; /* 0x41c */
+};
+
+/* BCH error status & location register */
+struct location {
+ u32 location_status; /* 0x800 */
+ u8 res1[124]; /* 0x804 */
+ u32 error_location_x[16]; /* 0x880.... */
+ u8 res2[64]; /* 0x8c0 */
+};
+
+/* BCH ELM register map - do not try to allocate memmory for this structure.
+ * We have used plenty of reserved variables to fill the slots in the ELM
+ * register memory map.
+ * Directly initialize the struct pointer to ELM base address.
+ */
+struct elm {
+ u32 rev; /* 0x000 */
+ u8 res1[12]; /* 0x004 */
+ u32 sysconfig; /* 0x010 */
+ u32 sysstatus; /* 0x014 */
+ u32 irqstatus; /* 0x018 */
+ u32 irqenable; /* 0x01c */
+ u32 location_config; /* 0x020 */
+ u8 res2[92]; /* 0x024 */
+ u32 page_ctrl; /* 0x080 */
+ u8 res3[892]; /* 0x084 */
+ struct syndrome syndrome_fragments[8]; /* 0x400 */
+ u8 res4[512]; /* 0x600 */
+ struct location error_location[8]; /* 0x800 */
+};
+
+int elm_check_error(u8 *syndrome, u32 nibbles, u32 *error_count,
+ u32 *error_locations);
+int elm_config(enum bch_level level);
+void elm_reset(void);
+void elm_init(void);
+#endif /* __ASSEMBLY__ */
+#endif /* __ASM_ARCH_ELM_H */
#define DDRPHY_0_CONFIG_BASE (CTRL_BASE + 0x1400)
#define DDRPHY_CONFIG_BASE DDRPHY_0_CONFIG_BASE
+/* GPMC Base address */
+#define GPMC_BASE 0x50000000
+
/* CPSW Config space */
#define AM335X_CPSW_BASE 0x4A100000
#define AM335X_CPSW_MDIO_BASE 0x4A101000
--- /dev/null
+/*
+ * (C) Copyright 2006-2008
+ * Texas Instruments, <www.ti.com>
+ *
+ * Author
+ * Mansoor Ahamed <mansoor.ahamed@ti.com>
+ *
+ * Initial Code from:
+ * Richard Woodruff <r-woodruff2@ti.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef _MEM_H_
+#define _MEM_H_
+
+/*
+ * GPMC settings -
+ * Definitions is as per the following format
+ * #define <PART>_GPMC_CONFIG<x> <value>
+ * Where:
+ * PART is the part name e.g. STNOR - Intel Strata Flash
+ * x is GPMC config registers from 1 to 6 (there will be 6 macros)
+ * Value is corresponding value
+ *
+ * For every valid PRCM configuration there should be only one definition of
+ * the same. if values are independent of the board, this definition will be
+ * present in this file if values are dependent on the board, then this should
+ * go into corresponding mem-boardName.h file
+ *
+ * Currently valid part Names are (PART):
+ * M_NAND - Micron NAND
+ */
+#define GPMC_SIZE_256M 0x0
+#define GPMC_SIZE_128M 0x8
+#define GPMC_SIZE_64M 0xC
+#define GPMC_SIZE_32M 0xE
+#define GPMC_SIZE_16M 0xF
+
+#define M_NAND_GPMC_CONFIG1 0x00000800
+#define M_NAND_GPMC_CONFIG2 0x001e1e00
+#define M_NAND_GPMC_CONFIG3 0x001e1e00
+#define M_NAND_GPMC_CONFIG4 0x16051807
+#define M_NAND_GPMC_CONFIG5 0x00151e1e
+#define M_NAND_GPMC_CONFIG6 0x16000f80
+#define M_NAND_GPMC_CONFIG7 0x00000008
+
+/* max number of GPMC Chip Selects */
+#define GPMC_MAX_CS 8
+/* max number of GPMC regs */
+#define GPMC_MAX_REG 7
+
+#define PISMO1_NOR 1
+#define PISMO1_NAND 2
+#define PISMO2_CS0 3
+#define PISMO2_CS1 4
+#define PISMO1_ONENAND 5
+#define DBG_MPDB 6
+#define PISMO2_NAND_CS0 7
+#define PISMO2_NAND_CS1 8
+
+/* make it readable for the gpmc_init */
+#define PISMO1_NOR_BASE FLASH_BASE
+#define PISMO1_NAND_BASE CONFIG_SYS_NAND_BASE
+#define PISMO1_NAND_SIZE GPMC_SIZE_256M
+
+#endif /* endif _MEM_H_ */
--- /dev/null
+/*
+ * (C) Copyright 2004-2008 Texas Instruments, <www.ti.com>
+ * Rohit Choraria <rohitkc@ti.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#ifndef __ASM_ARCH_OMAP_GPMC_H
+#define __ASM_ARCH_OMAP_GPMC_H
+
+#define GPMC_BUF_EMPTY 0
+#define GPMC_BUF_FULL 1
+
+#define ECCCLEAR (0x1 << 8)
+#define ECCRESULTREG1 (0x1 << 0)
+#define ECCSIZE512BYTE 0xFF
+#define ECCSIZE1 (ECCSIZE512BYTE << 22)
+#define ECCSIZE0 (ECCSIZE512BYTE << 12)
+#define ECCSIZE0SEL (0x000 << 0)
+
+/* Generic ECC Layouts */
+/* Large Page x8 NAND device Layout */
+#ifdef GPMC_NAND_ECC_LP_x8_LAYOUT
+#define GPMC_NAND_HW_ECC_LAYOUT {\
+ .eccbytes = 12,\
+ .eccpos = {1, 2, 3, 4, 5, 6, 7, 8,\
+ 9, 10, 11, 12},\
+ .oobfree = {\
+ {.offset = 13,\
+ .length = 51 } } \
+}
+#endif
+
+/* Large Page x16 NAND device Layout */
+#ifdef GPMC_NAND_ECC_LP_x16_LAYOUT
+#define GPMC_NAND_HW_ECC_LAYOUT {\
+ .eccbytes = 12,\
+ .eccpos = {2, 3, 4, 5, 6, 7, 8, 9,\
+ 10, 11, 12, 13},\
+ .oobfree = {\
+ {.offset = 14,\
+ .length = 50 } } \
+}
+#endif
+
+/* Small Page x8 NAND device Layout */
+#ifdef GPMC_NAND_ECC_SP_x8_LAYOUT
+#define GPMC_NAND_HW_ECC_LAYOUT {\
+ .eccbytes = 3,\
+ .eccpos = {1, 2, 3},\
+ .oobfree = {\
+ {.offset = 4,\
+ .length = 12 } } \
+}
+#endif
+
+/* Small Page x16 NAND device Layout */
+#ifdef GPMC_NAND_ECC_SP_x16_LAYOUT
+#define GPMC_NAND_HW_ECC_LAYOUT {\
+ .eccbytes = 3,\
+ .eccpos = {2, 3, 4},\
+ .oobfree = {\
+ {.offset = 5,\
+ .length = 11 } } \
+}
+#endif
+
+#define GPMC_NAND_HW_BCH4_ECC_LAYOUT {\
+ .eccbytes = 32,\
+ .eccpos = {2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15,\
+ 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27,\
+ 28, 29, 30, 31, 32, 33},\
+ .oobfree = {\
+ {.offset = 34,\
+ .length = 30 } } \
+}
+
+#define GPMC_NAND_HW_BCH8_ECC_LAYOUT {\
+ .eccbytes = 56,\
+ .eccpos = {2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15,\
+ 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27,\
+ 28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 39,\
+ 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 50, 51,\
+ 52, 53, 54, 55, 56, 57},\
+ .oobfree = {\
+ {.offset = 58,\
+ .length = 6 } } \
+}
+
+#define GPMC_NAND_HW_BCH16_ECC_LAYOUT {\
+ .eccbytes = 104,\
+ .eccpos = {2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15,\
+ 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27,\
+ 28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 39,\
+ 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 50, 51,\
+ 52, 53, 54, 55, 56, 57, 58, 59, 60, 61, 62, 63,\
+ 64, 65, 66, 67, 68, 69, 70, 71, 72, 73, 74, 75,\
+ 76, 77, 78, 79, 80, 81, 82, 83, 84, 85, 86, 87,\
+ 88, 89, 90, 91, 92, 93, 94, 95, 96, 97, 98, 99,\
+ 100, 101, 102, 103, 104, 105},\
+ .oobfree = {\
+ {.offset = 106,\
+ .length = 8 } } \
+}
+#endif /* __ASM_ARCH_OMAP_GPMC_H */
void setup_clocks_for_console(void);
void ddr_pll_config(unsigned int ddrpll_M);
+void sdelay(unsigned long);
+void gpmc_init(void);
+void omap_nand_switch_ecc(int);
#endif
u32 param1;
};
+/* Board SDRC timing values */
+struct board_sdrc_timings {
+ u32 mcfg;
+ u32 ctrla;
+ u32 ctrlb;
+ u32 rfr_ctrl;
+ u32 mr;
+};
+
void prcm_init(void);
void per_clocks_enable(void);
void ehci_clocks_enable(void);
void memif_init(void);
void sdrc_init(void);
void do_sdrc_init(u32, u32);
-void get_board_mem_timings(u32 *mcfg, u32 *ctrla, u32 *ctrlb, u32 *rfr_ctrl,
- u32 *mr);
+
+void get_board_mem_timings(struct board_sdrc_timings *timings);
void identify_nand_chip(int *mfr, int *id);
void emif4_init(void);
void gpmc_init(void);
#define METHOD_GPIO_24XX 4
+/**
+ * Check if gpio is valid.
+ *
+ * @param gpio GPIO number
+ * @return 1 if ok, 0 on error
+ */
+int gpio_is_valid(int gpio);
#endif /* _GPIO_H_ */
* provides the timing values back to the function that configures
* the memory. We have either one or two banks of 128MB DDR.
*/
-void get_board_mem_timings(u32 *mcfg, u32 *ctrla, u32 *ctrlb, u32 *rfr_ctrl,
- u32 *mr)
+void get_board_mem_timings(struct board_sdrc_timings *timings)
{
/* General SDRC config */
- *mcfg = MICRON_V_MCFG_165(128 << 20);
- *rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+ timings->mcfg = MICRON_V_MCFG_165(128 << 20);
+ timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
/* AC timings */
- *ctrla = MICRON_V_ACTIMA_165;
- *ctrlb = MICRON_V_ACTIMB_165;
- *mr = MICRON_V_MR_165;
+ timings->ctrla = MICRON_V_ACTIMA_165;
+ timings->ctrlb = MICRON_V_ACTIMB_165;
+ timings->mr = MICRON_V_MR_165;
}
* Description: If we use SPL then there is no x-loader nor config header
* so we have to setup the DDR timings ourself on both banks.
*/
-void get_board_mem_timings(u32 *mcfg, u32 *ctrla, u32 *ctrlb, u32 *rfr_ctrl,
- u32 *mr)
+void get_board_mem_timings(struct board_sdrc_timings *timings)
{
- *mr = MICRON_V_MR_165;
+ timings->mr = MICRON_V_MR_165;
#ifdef CONFIG_BOOT_NAND
- *mcfg = MICRON_V_MCFG_200(256 << 20);
- *ctrla = MICRON_V_ACTIMA_200;
- *ctrlb = MICRON_V_ACTIMB_200;
- *rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
+ timings->mcfg = MICRON_V_MCFG_200(256 << 20);
+ timings->ctrla = MICRON_V_ACTIMA_200;
+ timings->ctrlb = MICRON_V_ACTIMB_200;
+ timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
#else
if (get_cpu_family() == CPU_OMAP34XX) {
- *mcfg = NUMONYX_V_MCFG_165(256 << 20);
- *ctrla = NUMONYX_V_ACTIMA_165;
- *ctrlb = NUMONYX_V_ACTIMB_165;
- *rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+ timings->mcfg = NUMONYX_V_MCFG_165(256 << 20);
+ timings->ctrla = NUMONYX_V_ACTIMA_165;
+ timings->ctrlb = NUMONYX_V_ACTIMB_165;
+ timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
} else {
- *mcfg = NUMONYX_V_MCFG_200(256 << 20);
- *ctrla = NUMONYX_V_ACTIMA_200;
- *ctrlb = NUMONYX_V_ACTIMB_200;
- *rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
+ timings->mcfg = NUMONYX_V_MCFG_200(256 << 20);
+ timings->ctrla = NUMONYX_V_ACTIMA_200;
+ timings->ctrlb = NUMONYX_V_ACTIMB_200;
+ timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
}
#endif
}
* Description: If we use SPL then there is no x-loader nor config header
* so we have to setup the DDR timings ourself on both banks.
*/
-void get_board_mem_timings(u32 *mcfg, u32 *ctrla, u32 *ctrlb, u32 *rfr_ctrl,
- u32 *mr)
+void get_board_mem_timings(struct board_sdrc_timings *timings)
{
- *mr = MICRON_V_MR_165;
+ timings->mr = MICRON_V_MR_165;
#ifdef CONFIG_BOOT_NAND
- *mcfg = MICRON_V_MCFG_200(256 << 20);
- *ctrla = MICRON_V_ACTIMA_200;
- *ctrlb = MICRON_V_ACTIMB_200;
- *rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
+ timings->mcfg = MICRON_V_MCFG_200(256 << 20);
+ timings->ctrla = MICRON_V_ACTIMA_200;
+ timings->ctrlb = MICRON_V_ACTIMB_200;
+ timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
#else
if (get_cpu_family() == CPU_OMAP34XX) {
- *mcfg = NUMONYX_V_MCFG_165(256 << 20);
- *ctrla = NUMONYX_V_ACTIMA_165;
- *ctrlb = NUMONYX_V_ACTIMB_165;
- *rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+ timings->mcfg = NUMONYX_V_MCFG_165(256 << 20);
+ timings->ctrla = NUMONYX_V_ACTIMA_165;
+ timings->ctrlb = NUMONYX_V_ACTIMB_165;
+ timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
} else {
- *mcfg = NUMONYX_V_MCFG_200(256 << 20);
- *ctrla = NUMONYX_V_ACTIMA_200;
- *ctrlb = NUMONYX_V_ACTIMB_200;
- *rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
+ timings->mcfg = NUMONYX_V_MCFG_200(256 << 20);
+ timings->ctrla = NUMONYX_V_ACTIMA_200;
+ timings->ctrlb = NUMONYX_V_ACTIMB_200;
+ timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
}
#endif
}
* Description: If we use SPL then there is no x-loader nor config header
* so we have to setup the DDR timings ourself on both banks.
*/
-void get_board_mem_timings(u32 *mcfg, u32 *ctrla, u32 *ctrlb, u32 *rfr_ctrl,
- u32 *mr)
+void get_board_mem_timings(struct board_sdrc_timings *timings)
{
- *mr = MICRON_V_MR_165;
+ timings->mr = MICRON_V_MR_165;
switch (get_board_revision()) {
case REVISION_0: /* Micron 1286MB/256MB, 1/2 banks of 128MB */
- *mcfg = MICRON_V_MCFG_165(128 << 20);
- *ctrla = MICRON_V_ACTIMA_165;
- *ctrlb = MICRON_V_ACTIMB_165;
- *rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+ timings->mcfg = MICRON_V_MCFG_165(128 << 20);
+ timings->ctrla = MICRON_V_ACTIMA_165;
+ timings->ctrlb = MICRON_V_ACTIMB_165;
+ timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
break;
case REVISION_1: /* Micron 256MB/512MB, 1/2 banks of 256MB */
- *mcfg = MICRON_V_MCFG_165(256 << 20);
- *ctrla = MICRON_V_ACTIMA_165;
- *ctrlb = MICRON_V_ACTIMB_165;
- *rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+ timings->mcfg = MICRON_V_MCFG_165(256 << 20);
+ timings->ctrla = MICRON_V_ACTIMA_165;
+ timings->ctrlb = MICRON_V_ACTIMB_165;
+ timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
break;
case REVISION_2: /* Hynix 256MB/512MB, 1/2 banks of 256MB */
- *mcfg = HYNIX_V_MCFG_165(256 << 20);
- *ctrla = HYNIX_V_ACTIMA_165;
- *ctrlb = HYNIX_V_ACTIMB_165;
- *rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+ timings->mcfg = HYNIX_V_MCFG_165(256 << 20);
+ timings->ctrla = HYNIX_V_ACTIMA_165;
+ timings->ctrlb = HYNIX_V_ACTIMB_165;
+ timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
break;
default:
- *mcfg = MICRON_V_MCFG_165(128 << 20);
- *ctrla = MICRON_V_ACTIMA_165;
- *ctrlb = MICRON_V_ACTIMB_165;
- *rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+ timings->mcfg = MICRON_V_MCFG_165(128 << 20);
+ timings->ctrla = MICRON_V_ACTIMA_165;
+ timings->ctrlb = MICRON_V_ACTIMB_165;
+ timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
}
}
#endif
return 0;
}
+#ifndef CONFIG_SPL_BUILD
int misc_init_r(void)
{
char *eth_addr;
+ struct tam3517_module_info info;
+ int ret;
dieid_num_r();
if (eth_addr)
return 0;
-#ifndef CONFIG_SPL_BUILD
- TAM3517_READ_MAC_FROM_EEPROM;
-#endif
+ TAM3517_READ_EEPROM(&info, ret);
+ if (!ret)
+ TAM3517_READ_MAC_FROM_EEPROM(&info);
return 0;
}
+#endif
/*
* Routine: set_muxconf_regs
static struct panel_config lcd_cfg[] = {
{
- .timing_h = PANEL_TIMING_H(4, 8, 41),
- .timing_v = PANEL_TIMING_V(2, 4, 10),
- .pol_freq = 0x00000000, /* Pol Freq */
- .divisor = 0x0001000d, /* 33Mhz Pixel Clock */
+ .timing_h = PANEL_TIMING_H(40, 5, 2),
+ .timing_v = PANEL_TIMING_V(8, 8, 2),
+ .pol_freq = 0x00003000, /* Pol Freq */
+ .divisor = 0x00010033, /* 9 Mhz Pixel Clock */
.panel_type = 0x01, /* TFT */
.data_lines = 0x03, /* 24 Bit RGB */
.load_mode = 0x02, /* Frame Mode */
return 0;
}
+#ifndef CONFIG_SPL_BUILD
int misc_init_r(void)
{
char *eth_addr;
+ struct tam3517_module_info info;
+ int ret;
+ TAM3517_READ_EEPROM(&info, ret);
dieid_num_r();
- eth_addr = getenv("ethaddr");
- if (eth_addr)
+ if (ret)
return 0;
+ eth_addr = getenv("ethaddr");
+ if (!eth_addr)
+ TAM3517_READ_MAC_FROM_EEPROM(&info);
-#ifndef CONFIG_SPL_BUILD
- TAM3517_READ_MAC_FROM_EEPROM;
-#endif
+ TAM3517_PRINT_SOM_INFO(&info);
return 0;
}
+#endif
/*
* Routine: set_muxconf_regs
/* MII mode defines */
#define MII_MODE_ENABLE 0x0
-#define RGMII_MODE_ENABLE 0xA
+#define RGMII_MODE_ENABLE 0x3A
/* GPIO that controls power to DDR on EVM-SK */
#define GPIO_DDR_VTT_EN 7
gd->bd->bi_boot_params = PHYS_DRAM_1 + 0x100;
+ gpmc_init();
+
return 0;
}
{-1},
};
+static struct module_pin_mux nand_pin_mux[] = {
+ {OFFSET(gpmc_ad0), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD0 */
+ {OFFSET(gpmc_ad1), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD1 */
+ {OFFSET(gpmc_ad2), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD2 */
+ {OFFSET(gpmc_ad3), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD3 */
+ {OFFSET(gpmc_ad4), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD4 */
+ {OFFSET(gpmc_ad5), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD5 */
+ {OFFSET(gpmc_ad6), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD6 */
+ {OFFSET(gpmc_ad7), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD7 */
+ {OFFSET(gpmc_wait0), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* NAND WAIT */
+ {OFFSET(gpmc_wpn), (MODE(7) | PULLUP_EN | RXACTIVE)}, /* NAND_WPN */
+ {OFFSET(gpmc_csn0), (MODE(0) | PULLUDEN)}, /* NAND_CS0 */
+ {OFFSET(gpmc_advn_ale), (MODE(0) | PULLUDEN)}, /* NAND_ADV_ALE */
+ {OFFSET(gpmc_oen_ren), (MODE(0) | PULLUDEN)}, /* NAND_OE */
+ {OFFSET(gpmc_wen), (MODE(0) | PULLUDEN)}, /* NAND_WEN */
+ {OFFSET(gpmc_be0n_cle), (MODE(0) | PULLUDEN)}, /* NAND_BE_CLE */
+ {-1},
+};
+
void enable_uart0_pin_mux(void)
{
configure_module_pin_mux(uart0_pin_mux);
/* In profile #2 i2c1 and spi0 conflict. */
if (profile & ~PROFILE_2)
configure_module_pin_mux(i2c1_pin_mux);
+ /* Profiles 2 & 3 don't have NAND */
+ if (profile & ~(PROFILE_2 | PROFILE_3))
+ configure_module_pin_mux(nand_pin_mux);
else if (profile == PROFILE_2) {
configure_module_pin_mux(mmc1_pin_mux);
configure_module_pin_mux(spi0_pin_mux);
* Description: If we use SPL then there is no x-loader nor config header
* so we have to setup the DDR timings ourself on both banks.
*/
-void get_board_mem_timings(u32 *mcfg, u32 *ctrla, u32 *ctrlb, u32 *rfr_ctrl,
- u32 *mr)
+void get_board_mem_timings(struct board_sdrc_timings *timings)
{
int pop_mfr, pop_id;
*/
identify_nand_chip(&pop_mfr, &pop_id);
- *mr = MICRON_V_MR_165;
+ timings->mr = MICRON_V_MR_165;
switch (get_board_revision()) {
case REVISION_C4:
if (pop_mfr == NAND_MFR_STMICRO && pop_id == 0xba) {
/* 512MB DDR */
- *mcfg = NUMONYX_V_MCFG_165(512 << 20);
- *ctrla = NUMONYX_V_ACTIMA_165;
- *ctrlb = NUMONYX_V_ACTIMB_165;
- *rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+ timings->mcfg = NUMONYX_V_MCFG_165(512 << 20);
+ timings->ctrla = NUMONYX_V_ACTIMA_165;
+ timings->ctrlb = NUMONYX_V_ACTIMB_165;
+ timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
break;
} else if (pop_mfr == NAND_MFR_MICRON && pop_id == 0xba) {
/* Beagleboard Rev C4, 512MB Nand/256MB DDR*/
- *mcfg = MICRON_V_MCFG_165(128 << 20);
- *ctrla = MICRON_V_ACTIMA_165;
- *ctrlb = MICRON_V_ACTIMB_165;
- *rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+ timings->mcfg = MICRON_V_MCFG_165(128 << 20);
+ timings->ctrla = MICRON_V_ACTIMA_165;
+ timings->ctrlb = MICRON_V_ACTIMB_165;
+ timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
break;
} else if (pop_mfr == NAND_MFR_MICRON && pop_id == 0xbc) {
/* Beagleboard Rev C5, 256MB DDR */
- *mcfg = MICRON_V_MCFG_200(256 << 20);
- *ctrla = MICRON_V_ACTIMA_200;
- *ctrlb = MICRON_V_ACTIMB_200;
- *rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
+ timings->mcfg = MICRON_V_MCFG_200(256 << 20);
+ timings->ctrla = MICRON_V_ACTIMA_200;
+ timings->ctrlb = MICRON_V_ACTIMB_200;
+ timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
break;
}
case REVISION_XM_A:
case REVISION_XM_C:
if (pop_mfr == 0) {
/* 256MB DDR */
- *mcfg = MICRON_V_MCFG_200(256 << 20);
- *ctrla = MICRON_V_ACTIMA_200;
- *ctrlb = MICRON_V_ACTIMB_200;
- *rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
+ timings->mcfg = MICRON_V_MCFG_200(256 << 20);
+ timings->ctrla = MICRON_V_ACTIMA_200;
+ timings->ctrlb = MICRON_V_ACTIMB_200;
+ timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
} else {
/* 512MB DDR */
- *mcfg = NUMONYX_V_MCFG_165(512 << 20);
- *ctrla = NUMONYX_V_ACTIMA_165;
- *ctrlb = NUMONYX_V_ACTIMB_165;
- *rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+ timings->mcfg = NUMONYX_V_MCFG_165(512 << 20);
+ timings->ctrla = NUMONYX_V_ACTIMA_165;
+ timings->ctrlb = NUMONYX_V_ACTIMB_165;
+ timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
}
break;
default:
/* Assume 128MB and Micron/165MHz timings to be safe */
- *mcfg = MICRON_V_MCFG_165(128 << 20);
- *ctrla = MICRON_V_ACTIMA_165;
- *ctrlb = MICRON_V_ACTIMB_165;
- *rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+ timings->mcfg = MICRON_V_MCFG_165(128 << 20);
+ timings->ctrla = MICRON_V_ACTIMA_165;
+ timings->ctrlb = MICRON_V_ACTIMB_165;
+ timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
}
}
#endif
* provides the timing values back to the function that configures
* the memory.
*/
-void get_board_mem_timings(u32 *mcfg, u32 *ctrla, u32 *ctrlb, u32 *rfr_ctrl,
- u32 *mr)
+void get_board_mem_timings(struct board_sdrc_timings *timings)
{
int pop_mfr, pop_id;
if (pop_mfr == NAND_MFR_HYNIX && pop_id == 0xbc) {
/* 256MB DDR */
- *mcfg = HYNIX_V_MCFG_200(256 << 20);
- *ctrla = HYNIX_V_ACTIMA_200;
- *ctrlb = HYNIX_V_ACTIMB_200;
+ timings->mcfg = HYNIX_V_MCFG_200(256 << 20);
+ timings->ctrla = HYNIX_V_ACTIMA_200;
+ timings->ctrlb = HYNIX_V_ACTIMB_200;
} else {
/* 128MB DDR */
- *mcfg = MICRON_V_MCFG_165(128 << 20);
- *ctrla = MICRON_V_ACTIMA_165;
- *ctrlb = MICRON_V_ACTIMB_165;
+ timings->mcfg = MICRON_V_MCFG_165(128 << 20);
+ timings->ctrla = MICRON_V_ACTIMA_165;
+ timings->ctrlb = MICRON_V_ACTIMB_165;
}
- *rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
- *mr = MICRON_V_MR_165;
+ timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+ timings->mr = MICRON_V_MR_165;
}
#endif
* provides the timing values back to the function that configures
* the memory. We have either one or two banks of 128MB DDR.
*/
-void get_board_mem_timings(u32 *mcfg, u32 *ctrla, u32 *ctrlb, u32 *rfr_ctrl,
- u32 *mr)
+void get_board_mem_timings(struct board_sdrc_timings *timings)
{
/* General SDRC config */
- *mcfg = MICRON_V_MCFG_165(128 << 20);
- *rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+ timings->mcfg = MICRON_V_MCFG_165(128 << 20);
+ timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
/* AC timings */
- *ctrla = MICRON_V_ACTIMA_165;
- *ctrlb = MICRON_V_ACTIMB_165;
+ timings->ctrla = MICRON_V_ACTIMA_165;
+ timings->ctrlb = MICRON_V_ACTIMB_165;
- *mr = MICRON_V_MR_165;
+ timings->mr = MICRON_V_MR_165;
}
return gpio & 0x1f;
}
-static inline int gpio_valid(int gpio)
+int gpio_is_valid(int gpio)
{
- if (gpio < 0)
- return -1;
- if (gpio < 192)
- return 0;
- return -1;
+ return (gpio >= 0) && (gpio < 192);
}
static int check_gpio(int gpio)
{
- if (gpio_valid(gpio) < 0) {
+ if (!gpio_is_valid(gpio)) {
printf("ERROR : check_gpio: invalid GPIO %d\n", gpio);
return -1;
}
#define I2C_TIMEOUT 1000
-static void wait_for_bb(void);
+static int wait_for_bb(void);
static u16 wait_for_pin(void);
static void flush_fifo(void);
u16 w;
/* wait until bus not busy */
- wait_for_bb();
+ if (wait_for_bb())
+ return 1;
/* one byte only */
writew(alen, &i2c_base->cnt);
return res;
/* wait until bus not busy */
- wait_for_bb();
+ if (wait_for_bb())
+ return res;
/* try to read one byte */
writew(1, &i2c_base->cnt);
res = 1;
writew(0xff, &i2c_base->stat);
writew (readw (&i2c_base->con) | I2C_CON_STP, &i2c_base->con);
- wait_for_bb ();
+
+ if (wait_for_bb())
+ res = 1;
+
break;
}
if (status & I2C_STAT_ARDY) {
}
/* wait until bus not busy */
- wait_for_bb();
+ if (wait_for_bb())
+ return 1;
/* start address phase - will write regoffset + len bytes data */
/* TODO consider case when !CONFIG_OMAP243X/34XX/44XX */
return i2c_error;
}
-static void wait_for_bb(void)
+static int wait_for_bb(void)
{
int timeout = I2C_TIMEOUT;
u16 stat;
if (timeout <= 0) {
printf("timed out in wait_for_bb: I2C_STAT=%x\n",
readw(&i2c_base->stat));
+ return 1;
}
writew(0xFFFF, &i2c_base->stat); /* clear delayed stuff*/
+ return 0;
}
static u16 wait_for_pin(void)
NORMAL_DRIVERS=y
endif
+COBJS-$(CONFIG_SPL_NAND_AM33XX_BCH) += am335x_spl_bch.o
COBJS-$(CONFIG_SPL_NAND_SIMPLE) += nand_spl_simple.o
COBJS-$(CONFIG_SPL_NAND_LOAD) += nand_spl_load.o
COBJS-$(CONFIG_SPL_NAND_ECC) += nand_ecc.o
COBJS-$(CONFIG_NAND_OMAP_GPMC) += omap_gpmc.o
COBJS-$(CONFIG_NAND_PLAT) += nand_plat.o
-else # minimal SPL drivers
-
-COBJS-$(CONFIG_NAND_FSL_ELBC) += fsl_elbc_spl.o
-
endif # drivers
endif # nand
--- /dev/null
+/*
+ * (C) Copyright 2012
+ * Konstantin Kozhevnikov, Cogent Embedded
+ *
+ * based on nand_spl_simple code
+ *
+ * (C) Copyright 2006-2008
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc.
+ */
+
+#include <common.h>
+#include <nand.h>
+#include <asm/io.h>
+#include <linux/mtd/nand_ecc.h>
+
+static int nand_ecc_pos[] = CONFIG_SYS_NAND_ECCPOS;
+static nand_info_t mtd;
+static struct nand_chip nand_chip;
+
+#define ECCSTEPS (CONFIG_SYS_NAND_PAGE_SIZE / \
+ CONFIG_SYS_NAND_ECCSIZE)
+#define ECCTOTAL (ECCSTEPS * CONFIG_SYS_NAND_ECCBYTES)
+
+
+/*
+ * NAND command for large page NAND devices (2k)
+ */
+static int nand_command(int block, int page, uint32_t offs,
+ u8 cmd)
+{
+ struct nand_chip *this = mtd.priv;
+ int page_addr = page + block * CONFIG_SYS_NAND_PAGE_COUNT;
+ void (*hwctrl)(struct mtd_info *mtd, int cmd,
+ unsigned int ctrl) = this->cmd_ctrl;
+
+ while (!this->dev_ready(&mtd))
+ ;
+
+ /* Emulate NAND_CMD_READOOB */
+ if (cmd == NAND_CMD_READOOB) {
+ offs += CONFIG_SYS_NAND_PAGE_SIZE;
+ cmd = NAND_CMD_READ0;
+ }
+
+ /* Begin command latch cycle */
+ hwctrl(&mtd, cmd, NAND_CTRL_CLE | NAND_CTRL_CHANGE);
+
+ if (cmd == NAND_CMD_RESET) {
+ hwctrl(&mtd, NAND_CMD_NONE, NAND_NCE | NAND_CTRL_CHANGE);
+ while (!this->dev_ready(&mtd))
+ ;
+ return 0;
+ }
+
+ /* Shift the offset from byte addressing to word addressing. */
+ if (this->options & NAND_BUSWIDTH_16)
+ offs >>= 1;
+
+ /* Set ALE and clear CLE to start address cycle */
+ /* Column address */
+ hwctrl(&mtd, offs & 0xff,
+ NAND_CTRL_ALE | NAND_CTRL_CHANGE); /* A[7:0] */
+ hwctrl(&mtd, (offs >> 8) & 0xff, NAND_CTRL_ALE); /* A[11:9] */
+ /* Row address */
+ hwctrl(&mtd, (page_addr & 0xff), NAND_CTRL_ALE); /* A[19:12] */
+ hwctrl(&mtd, ((page_addr >> 8) & 0xff),
+ NAND_CTRL_ALE); /* A[27:20] */
+#ifdef CONFIG_SYS_NAND_5_ADDR_CYCLE
+ /* One more address cycle for devices > 128MiB */
+ hwctrl(&mtd, (page_addr >> 16) & 0x0f,
+ NAND_CTRL_ALE); /* A[31:28] */
+#endif
+ hwctrl(&mtd, NAND_CMD_NONE, NAND_NCE | NAND_CTRL_CHANGE);
+
+ if (cmd == NAND_CMD_READ0) {
+ /* Latch in address */
+ hwctrl(&mtd, NAND_CMD_READSTART,
+ NAND_CTRL_CLE | NAND_CTRL_CHANGE);
+ hwctrl(&mtd, NAND_CMD_NONE, NAND_NCE | NAND_CTRL_CHANGE);
+
+ /*
+ * Wait a while for the data to be ready
+ */
+ while (!this->dev_ready(&mtd))
+ ;
+ } else if (cmd == NAND_CMD_RNDOUT) {
+ hwctrl(&mtd, NAND_CMD_RNDOUTSTART, NAND_CTRL_CLE |
+ NAND_CTRL_CHANGE);
+ hwctrl(&mtd, NAND_CMD_NONE, NAND_NCE | NAND_CTRL_CHANGE);
+ }
+
+ return 0;
+}
+
+static int nand_is_bad_block(int block)
+{
+ struct nand_chip *this = mtd.priv;
+
+ nand_command(block, 0, CONFIG_SYS_NAND_BAD_BLOCK_POS,
+ NAND_CMD_READOOB);
+
+ /*
+ * Read one byte (or two if it's a 16 bit chip).
+ */
+ if (this->options & NAND_BUSWIDTH_16) {
+ if (readw(this->IO_ADDR_R) != 0xffff)
+ return 1;
+ } else {
+ if (readb(this->IO_ADDR_R) != 0xff)
+ return 1;
+ }
+
+ return 0;
+}
+
+static int nand_read_page(int block, int page, void *dst)
+{
+ struct nand_chip *this = mtd.priv;
+ u_char ecc_calc[ECCTOTAL];
+ u_char ecc_code[ECCTOTAL];
+ u_char oob_data[CONFIG_SYS_NAND_OOBSIZE];
+ int i;
+ int eccsize = CONFIG_SYS_NAND_ECCSIZE;
+ int eccbytes = CONFIG_SYS_NAND_ECCBYTES;
+ int eccsteps = ECCSTEPS;
+ uint8_t *p = dst;
+ uint32_t data_pos = 0;
+ uint8_t *oob = &oob_data[0] + nand_ecc_pos[0];
+ uint32_t oob_pos = eccsize * eccsteps + nand_ecc_pos[0];
+
+ nand_command(block, page, 0, NAND_CMD_READ0);
+
+ for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) {
+ this->ecc.hwctl(&mtd, NAND_ECC_READ);
+ nand_command(block, page, data_pos, NAND_CMD_RNDOUT);
+
+ this->read_buf(&mtd, p, eccsize);
+
+ nand_command(block, page, oob_pos, NAND_CMD_RNDOUT);
+
+ this->read_buf(&mtd, oob, eccbytes);
+ this->ecc.calculate(&mtd, p, &ecc_calc[i]);
+
+ data_pos += eccsize;
+ oob_pos += eccbytes;
+ oob += eccbytes;
+ }
+
+ /* Pick the ECC bytes out of the oob data */
+ for (i = 0; i < ECCTOTAL; i++)
+ ecc_code[i] = oob_data[nand_ecc_pos[i]];
+
+ eccsteps = ECCSTEPS;
+ p = dst;
+
+ for (i = 0 ; eccsteps; eccsteps--, i += eccbytes, p += eccsize) {
+ /* No chance to do something with the possible error message
+ * from correct_data(). We just hope that all possible errors
+ * are corrected by this routine.
+ */
+ this->ecc.correct(&mtd, p, &ecc_code[i], &ecc_calc[i]);
+ }
+
+ return 0;
+}
+
+int nand_spl_load_image(uint32_t offs, unsigned int size, void *dst)
+{
+ unsigned int block, lastblock;
+ unsigned int page;
+
+ /*
+ * offs has to be aligned to a page address!
+ */
+ block = offs / CONFIG_SYS_NAND_BLOCK_SIZE;
+ lastblock = (offs + size - 1) / CONFIG_SYS_NAND_BLOCK_SIZE;
+ page = (offs % CONFIG_SYS_NAND_BLOCK_SIZE) / CONFIG_SYS_NAND_PAGE_SIZE;
+
+ while (block <= lastblock) {
+ if (!nand_is_bad_block(block)) {
+ /*
+ * Skip bad blocks
+ */
+ while (page < CONFIG_SYS_NAND_PAGE_COUNT) {
+ nand_read_page(block, page, dst);
+ dst += CONFIG_SYS_NAND_PAGE_SIZE;
+ page++;
+ }
+
+ page = 0;
+ } else {
+ lastblock++;
+ }
+
+ block++;
+ }
+
+ return 0;
+}
+
+/* nand_init() - initialize data to make nand usable by SPL */
+void nand_init(void)
+{
+ /*
+ * Init board specific nand support
+ */
+ mtd.priv = &nand_chip;
+ nand_chip.IO_ADDR_R = nand_chip.IO_ADDR_W =
+ (void __iomem *)CONFIG_SYS_NAND_BASE;
+ board_nand_init(&nand_chip);
+
+ if (nand_chip.select_chip)
+ nand_chip.select_chip(&mtd, 0);
+
+ /* NAND chip may require reset after power-on */
+ nand_command(0, 0, 0, NAND_CMD_RESET);
+}
+
+/* Unselect after operation */
+void nand_deselect(void)
+{
+ if (nand_chip.select_chip)
+ nand_chip.select_chip(&mtd, -1);
+}
#include <linux/mtd/nand_ecc.h>
#include <linux/compiler.h>
#include <nand.h>
+#ifdef CONFIG_AM33XX
+#include <asm/arch/elm.h>
+#endif
static uint8_t cs;
static __maybe_unused struct nand_ecclayout hw_nand_oob =
}
}
+/*
+ * BCH8 support (needs ELM and thus AM33xx-only)
+ */
+#ifdef CONFIG_AM33XX
+struct nand_bch_priv {
+ uint8_t mode;
+ uint8_t type;
+ uint8_t nibbles;
+};
+
+/* bch types */
+#define ECC_BCH4 0
+#define ECC_BCH8 1
+#define ECC_BCH16 2
+
+/* BCH nibbles for diff bch levels */
+#define NAND_ECC_HW_BCH ((uint8_t)(NAND_ECC_HW_OOB_FIRST) + 1)
+#define ECC_BCH4_NIBBLES 13
+#define ECC_BCH8_NIBBLES 26
+#define ECC_BCH16_NIBBLES 52
+
+static struct nand_ecclayout hw_bch8_nand_oob = GPMC_NAND_HW_BCH8_ECC_LAYOUT;
+
+static struct nand_bch_priv bch_priv = {
+ .mode = NAND_ECC_HW_BCH,
+ .type = ECC_BCH8,
+ .nibbles = ECC_BCH8_NIBBLES
+};
+
+/*
+ * omap_read_bch8_result - Read BCH result for BCH8 level
+ *
+ * @mtd: MTD device structure
+ * @big_endian: When set read register 3 first
+ * @ecc_code: Read syndrome from BCH result registers
+ */
+static void omap_read_bch8_result(struct mtd_info *mtd, uint8_t big_endian,
+ uint8_t *ecc_code)
+{
+ uint32_t *ptr;
+ int8_t i = 0, j;
+
+ if (big_endian) {
+ ptr = &gpmc_cfg->bch_result_0_3[0].bch_result_x[3];
+ ecc_code[i++] = readl(ptr) & 0xFF;
+ ptr--;
+ for (j = 0; j < 3; j++) {
+ ecc_code[i++] = (readl(ptr) >> 24) & 0xFF;
+ ecc_code[i++] = (readl(ptr) >> 16) & 0xFF;
+ ecc_code[i++] = (readl(ptr) >> 8) & 0xFF;
+ ecc_code[i++] = readl(ptr) & 0xFF;
+ ptr--;
+ }
+ } else {
+ ptr = &gpmc_cfg->bch_result_0_3[0].bch_result_x[0];
+ for (j = 0; j < 3; j++) {
+ ecc_code[i++] = readl(ptr) & 0xFF;
+ ecc_code[i++] = (readl(ptr) >> 8) & 0xFF;
+ ecc_code[i++] = (readl(ptr) >> 16) & 0xFF;
+ ecc_code[i++] = (readl(ptr) >> 24) & 0xFF;
+ ptr++;
+ }
+ ecc_code[i++] = readl(ptr) & 0xFF;
+ ecc_code[i++] = 0; /* 14th byte is always zero */
+ }
+}
+
+/*
+ * omap_ecc_disable - Disable H/W ECC calculation
+ *
+ * @mtd: MTD device structure
+ *
+ */
+static void omap_ecc_disable(struct mtd_info *mtd)
+{
+ writel((readl(&gpmc_cfg->ecc_config) & ~0x1),
+ &gpmc_cfg->ecc_config);
+}
+
+/*
+ * omap_rotate_ecc_bch - Rotate the syndrome bytes
+ *
+ * @mtd: MTD device structure
+ * @calc_ecc: ECC read from ECC registers
+ * @syndrome: Rotated syndrome will be retuned in this array
+ *
+ */
+static void omap_rotate_ecc_bch(struct mtd_info *mtd, uint8_t *calc_ecc,
+ uint8_t *syndrome)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct nand_bch_priv *bch = chip->priv;
+ uint8_t n_bytes = 0;
+ int8_t i, j;
+
+ switch (bch->type) {
+ case ECC_BCH4:
+ n_bytes = 8;
+ break;
+
+ case ECC_BCH16:
+ n_bytes = 28;
+ break;
+
+ case ECC_BCH8:
+ default:
+ n_bytes = 13;
+ break;
+ }
+
+ for (i = 0, j = (n_bytes-1); i < n_bytes; i++, j--)
+ syndrome[i] = calc_ecc[j];
+}
+
+/*
+ * omap_calculate_ecc_bch - Read BCH ECC result
+ *
+ * @mtd: MTD structure
+ * @dat: unused
+ * @ecc_code: ecc_code buffer
+ */
+static int omap_calculate_ecc_bch(struct mtd_info *mtd, const uint8_t *dat,
+ uint8_t *ecc_code)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct nand_bch_priv *bch = chip->priv;
+ uint8_t big_endian = 1;
+ int8_t ret = 0;
+
+ if (bch->type == ECC_BCH8)
+ omap_read_bch8_result(mtd, big_endian, ecc_code);
+ else /* BCH4 and BCH16 currently not supported */
+ ret = -1;
+
+ /*
+ * Stop reading anymore ECC vals and clear old results
+ * enable will be called if more reads are required
+ */
+ omap_ecc_disable(mtd);
+
+ return ret;
+}
+
+/*
+ * omap_fix_errors_bch - Correct bch error in the data
+ *
+ * @mtd: MTD device structure
+ * @data: Data read from flash
+ * @error_count:Number of errors in data
+ * @error_loc: Locations of errors in the data
+ *
+ */
+static void omap_fix_errors_bch(struct mtd_info *mtd, uint8_t *data,
+ uint32_t error_count, uint32_t *error_loc)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct nand_bch_priv *bch = chip->priv;
+ uint8_t count = 0;
+ uint32_t error_byte_pos;
+ uint32_t error_bit_mask;
+ uint32_t last_bit = (bch->nibbles * 4) - 1;
+
+ /* Flip all bits as specified by the error location array. */
+ /* FOR( each found error location flip the bit ) */
+ for (count = 0; count < error_count; count++) {
+ if (error_loc[count] > last_bit) {
+ /* Remove the ECC spare bits from correction. */
+ error_loc[count] -= (last_bit + 1);
+ /* Offset bit in data region */
+ error_byte_pos = ((512 * 8) -
+ (error_loc[count]) - 1) / 8;
+ /* Error Bit mask */
+ error_bit_mask = 0x1 << (error_loc[count] % 8);
+ /* Toggle the error bit to make the correction. */
+ data[error_byte_pos] ^= error_bit_mask;
+ }
+ }
+}
+
+/*
+ * omap_correct_data_bch - Compares the ecc read from nand spare area
+ * with ECC registers values and corrects one bit error if it has occured
+ *
+ * @mtd: MTD device structure
+ * @dat: page data
+ * @read_ecc: ecc read from nand flash (ignored)
+ * @calc_ecc: ecc read from ECC registers
+ *
+ * @return 0 if data is OK or corrected, else returns -1
+ */
+static int omap_correct_data_bch(struct mtd_info *mtd, uint8_t *dat,
+ uint8_t *read_ecc, uint8_t *calc_ecc)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct nand_bch_priv *bch = chip->priv;
+ uint8_t syndrome[28];
+ uint32_t error_count = 0;
+ uint32_t error_loc[8];
+ uint32_t i, ecc_flag;
+
+ ecc_flag = 0;
+ for (i = 0; i < chip->ecc.bytes; i++)
+ if (read_ecc[i] != 0xff)
+ ecc_flag = 1;
+
+ if (!ecc_flag)
+ return 0;
+
+ elm_reset();
+ elm_config((enum bch_level)(bch->type));
+
+ /*
+ * while reading ECC result we read it in big endian.
+ * Hence while loading to ELM we have rotate to get the right endian.
+ */
+ omap_rotate_ecc_bch(mtd, calc_ecc, syndrome);
+
+ /* use elm module to check for errors */
+ if (elm_check_error(syndrome, bch->nibbles, &error_count,
+ error_loc) != 0) {
+ printf("ECC: uncorrectable.\n");
+ return -1;
+ }
+
+ /* correct bch error */
+ if (error_count > 0)
+ omap_fix_errors_bch(mtd, dat, error_count, error_loc);
+
+ return 0;
+}
+/*
+ * omap_hwecc_init_bch - Initialize the BCH Hardware ECC for NAND flash in
+ * GPMC controller
+ * @mtd: MTD device structure
+ * @mode: Read/Write mode
+ */
+static void omap_hwecc_init_bch(struct nand_chip *chip, int32_t mode)
+{
+ uint32_t val, dev_width = (chip->options & NAND_BUSWIDTH_16) >> 1;
+ uint32_t unused_length = 0;
+ struct nand_bch_priv *bch = chip->priv;
+
+ switch (bch->nibbles) {
+ case ECC_BCH4_NIBBLES:
+ unused_length = 3;
+ break;
+ case ECC_BCH8_NIBBLES:
+ unused_length = 2;
+ break;
+ case ECC_BCH16_NIBBLES:
+ unused_length = 0;
+ break;
+ }
+
+ /* Clear the ecc result registers, select ecc reg as 1 */
+ writel(ECCCLEAR | ECCRESULTREG1, &gpmc_cfg->ecc_control);
+
+ switch (mode) {
+ case NAND_ECC_WRITE:
+ /* eccsize1 config */
+ val = ((unused_length + bch->nibbles) << 22);
+ break;
+
+ case NAND_ECC_READ:
+ default:
+ /* by default eccsize0 selected for ecc1resultsize */
+ /* eccsize0 config */
+ val = (bch->nibbles << 12);
+ /* eccsize1 config */
+ val |= (unused_length << 22);
+ break;
+ }
+ /* ecc size configuration */
+ writel(val, &gpmc_cfg->ecc_size_config);
+ /* by default 512bytes sector page is selected */
+ /* set bch mode */
+ val = (1 << 16);
+ /* bch4 / bch8 / bch16 */
+ val |= (bch->type << 12);
+ /* set wrap mode to 1 */
+ val |= (1 << 8);
+ val |= (dev_width << 7);
+ val |= (cs << 1);
+ writel(val, &gpmc_cfg->ecc_config);
+}
+
+/*
+ * omap_enable_ecc_bch- This function enables the bch h/w ecc functionality
+ * @mtd: MTD device structure
+ * @mode: Read/Write mode
+ *
+ */
+static void omap_enable_ecc_bch(struct mtd_info *mtd, int32_t mode)
+{
+ struct nand_chip *chip = mtd->priv;
+
+ omap_hwecc_init_bch(chip, mode);
+ /* enable ecc */
+ writel((readl(&gpmc_cfg->ecc_config) | 0x1), &gpmc_cfg->ecc_config);
+}
+
+/**
+ * omap_read_page_bch - hardware ecc based page read function
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @buf: buffer to store read data
+ * @page: page number to read
+ *
+ */
+static int omap_read_page_bch(struct mtd_info *mtd, struct nand_chip *chip,
+ uint8_t *buf, int page)
+{
+ int i, eccsize = chip->ecc.size;
+ int eccbytes = chip->ecc.bytes;
+ int eccsteps = chip->ecc.steps;
+ uint8_t *p = buf;
+ uint8_t *ecc_calc = chip->buffers->ecccalc;
+ uint8_t *ecc_code = chip->buffers->ecccode;
+ uint32_t *eccpos = chip->ecc.layout->eccpos;
+ uint8_t *oob = chip->oob_poi;
+ uint32_t data_pos;
+ uint32_t oob_pos;
+
+ data_pos = 0;
+ /* oob area start */
+ oob_pos = (eccsize * eccsteps) + chip->ecc.layout->eccpos[0];
+ oob += chip->ecc.layout->eccpos[0];
+
+ for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize,
+ oob += eccbytes) {
+ chip->ecc.hwctl(mtd, NAND_ECC_READ);
+ /* read data */
+ chip->cmdfunc(mtd, NAND_CMD_RNDOUT, data_pos, page);
+ chip->read_buf(mtd, p, eccsize);
+
+ /* read respective ecc from oob area */
+ chip->cmdfunc(mtd, NAND_CMD_RNDOUT, oob_pos, page);
+ chip->read_buf(mtd, oob, eccbytes);
+ /* read syndrome */
+ chip->ecc.calculate(mtd, p, &ecc_calc[i]);
+
+ data_pos += eccsize;
+ oob_pos += eccbytes;
+ }
+
+ for (i = 0; i < chip->ecc.total; i++)
+ ecc_code[i] = chip->oob_poi[eccpos[i]];
+
+ eccsteps = chip->ecc.steps;
+ p = buf;
+
+ for (i = 0 ; eccsteps; eccsteps--, i += eccbytes, p += eccsize) {
+ int stat;
+
+ stat = chip->ecc.correct(mtd, p, &ecc_code[i], &ecc_calc[i]);
+ if (stat < 0)
+ mtd->ecc_stats.failed++;
+ else
+ mtd->ecc_stats.corrected += stat;
+ }
+ return 0;
+}
+#endif /* CONFIG_AM33XX */
+
#ifndef CONFIG_SPL_BUILD
/*
* omap_nand_switch_ecc - switch the ECC operation b/w h/w ecc and s/w ecc.
nand->ecc.calculate = NULL;
/* Setup the ecc configurations again */
- if (hardware) {
+ if (hardware == 1) {
nand->ecc.mode = NAND_ECC_HW;
nand->ecc.layout = &hw_nand_oob;
nand->ecc.size = 512;
nand->ecc.calculate = omap_calculate_ecc;
omap_hwecc_init(nand);
printf("HW ECC selected\n");
+#ifdef CONFIG_AM33XX
+ } else if (hardware == 2) {
+ nand->ecc.mode = NAND_ECC_HW;
+ nand->ecc.layout = &hw_bch8_nand_oob;
+ nand->ecc.size = 512;
+ nand->ecc.bytes = 14;
+ nand->ecc.read_page = omap_read_page_bch;
+ nand->ecc.hwctl = omap_enable_ecc_bch;
+ nand->ecc.correct = omap_correct_data_bch;
+ nand->ecc.calculate = omap_calculate_ecc_bch;
+ omap_hwecc_init_bch(nand, NAND_ECC_READ);
+ printf("HW BCH8 selected\n");
+#endif
} else {
nand->ecc.mode = NAND_ECC_SOFT;
/* Use mtd default settings */
nand->options |= NAND_BUSWIDTH_16;
nand->chip_delay = 100;
+
+#ifdef CONFIG_AM33XX
+ /* required in case of BCH */
+ elm_init();
+
+ /* BCH info that will be correct for SPL or overridden otherwise. */
+ nand->priv = &bch_priv;
+#endif
+
/* Default ECC mode */
+#ifdef CONFIG_AM33XX
+ nand->ecc.mode = NAND_ECC_HW;
+ nand->ecc.layout = &hw_bch8_nand_oob;
+ nand->ecc.size = CONFIG_SYS_NAND_ECCSIZE;
+ nand->ecc.bytes = CONFIG_SYS_NAND_ECCBYTES;
+ nand->ecc.hwctl = omap_enable_ecc_bch;
+ nand->ecc.correct = omap_correct_data_bch;
+ nand->ecc.calculate = omap_calculate_ecc_bch;
+ nand->ecc.read_page = omap_read_page_bch;
+ omap_hwecc_init_bch(nand, NAND_ECC_READ);
+#else
#if !defined(CONFIG_SPL_BUILD) || defined(CONFIG_SPL_NAND_SOFTECC)
nand->ecc.mode = NAND_ECC_SOFT;
#else
nand->ecc.calculate = omap_calculate_ecc;
omap_hwecc_init(nand);
#endif
+#endif
#ifdef CONFIG_SPL_BUILD
if (nand->options & NAND_BUSWIDTH_16)
SUPPORTED_100baseT_Full |
SUPPORTED_1000baseT_Full);
- phydev = phy_connect(priv->bus, 0, dev, slave->data->phy_if);
+ phydev = phy_connect(priv->bus,
+ CONFIG_PHY_ADDR,
+ dev,
+ slave->data->phy_if);
phydev->supported &= supported;
phydev->advertising = phydev->supported;
return;
}
-void twl6035_mmc1_poweron_ldo(void)
+int twl6035_mmc1_poweron_ldo(void)
{
u8 val = 0;
/* set LDO9 TWL6035 to 3V */
val = 0x2b; /* (3 -.9)*28 +1 */
- palmas_write_u8(0x48, LDO9_VOLTAGE, val);
+
+ if (palmas_write_u8(0x48, LDO9_VOLTAGE, val)) {
+ printf("twl6035: could not set LDO9 voltage.\n");
+ return 1;
+ }
/* TURN ON LDO9 */
val = LDO_ON | LDO_MODE_SLEEP | LDO_MODE_ACTIVE;
- palmas_write_u8(0x48, LDO9_CTRL, val);
- return;
+
+ if (palmas_write_u8(0x48, LDO9_CTRL, val)) {
+ printf("twl6035: could not turn on LDO9.\n");
+ return 1;
+ }
+
+ return 0;
}
writel(OMAP3_MCSPI_WAKEUPENABLE_WKEN, &ds->regs->wakeupenable);
}
+static void omap3_spi_write_chconf(struct omap3_spi_slave *ds, int val)
+{
+ writel(val, &ds->regs->channel[ds->slave.cs].chconf);
+ /* Flash post writes to make immediate effect */
+ readl(&ds->regs->channel[ds->slave.cs].chconf);
+}
+
+static void omap3_spi_set_enable(struct omap3_spi_slave *ds, int enable)
+{
+ writel(enable, &ds->regs->channel[ds->slave.cs].chctrl);
+ /* Flash post writes to make immediate effect */
+ readl(&ds->regs->channel[ds->slave.cs].chctrl);
+}
+
void spi_init()
{
/* do nothing */
/* Transmit & receive mode */
conf &= ~OMAP3_MCSPI_CHCONF_TRM_MASK;
- writel(conf, &ds->regs->channel[ds->slave.cs].chconf);
+ omap3_spi_write_chconf(ds,conf);
return 0;
}
int timeout = SPI_WAIT_TIMEOUT;
int chconf = readl(&ds->regs->channel[ds->slave.cs].chconf);
- if (flags & SPI_XFER_BEGIN)
- writel(OMAP3_MCSPI_CHCTRL_EN,
- &ds->regs->channel[ds->slave.cs].chctrl);
+ /* Enable the channel */
+ omap3_spi_set_enable(ds,OMAP3_MCSPI_CHCTRL_EN);
chconf &= ~OMAP3_MCSPI_CHCONF_TRM_MASK;
chconf |= OMAP3_MCSPI_CHCONF_TRM_TX_ONLY;
chconf |= OMAP3_MCSPI_CHCONF_FORCE;
- writel(chconf, &ds->regs->channel[ds->slave.cs].chconf);
+ omap3_spi_write_chconf(ds,chconf);
for (i = 0; i < len; i++) {
/* wait till TX register is empty (TXS == 1) */
writel(txp[i], &ds->regs->channel[ds->slave.cs].tx);
}
+ /* wait to finish of transfer */
+ while (!(readl(&ds->regs->channel[ds->slave.cs].chstat) &
+ OMAP3_MCSPI_CHSTAT_EOT));
+
+ /* Disable the channel otherwise the next immediate RX will get affected */
+ omap3_spi_set_enable(ds,OMAP3_MCSPI_CHCTRL_DIS);
+
if (flags & SPI_XFER_END) {
- /* wait to finish of transfer */
- while (!(readl(&ds->regs->channel[ds->slave.cs].chstat) &
- OMAP3_MCSPI_CHSTAT_EOT));
chconf &= ~OMAP3_MCSPI_CHCONF_FORCE;
- writel(chconf, &ds->regs->channel[ds->slave.cs].chconf);
-
- writel(0, &ds->regs->channel[ds->slave.cs].chctrl);
+ omap3_spi_write_chconf(ds,chconf);
}
return 0;
}
int timeout = SPI_WAIT_TIMEOUT;
int chconf = readl(&ds->regs->channel[ds->slave.cs].chconf);
- if (flags & SPI_XFER_BEGIN)
- writel(OMAP3_MCSPI_CHCTRL_EN,
- &ds->regs->channel[ds->slave.cs].chctrl);
+ /* Enable the channel */
+ omap3_spi_set_enable(ds,OMAP3_MCSPI_CHCTRL_EN);
chconf &= ~OMAP3_MCSPI_CHCONF_TRM_MASK;
chconf |= OMAP3_MCSPI_CHCONF_TRM_RX_ONLY;
chconf |= OMAP3_MCSPI_CHCONF_FORCE;
- writel(chconf, &ds->regs->channel[ds->slave.cs].chconf);
+ omap3_spi_write_chconf(ds,chconf);
writel(0, &ds->regs->channel[ds->slave.cs].tx);
return -1;
}
}
+
+ /* Disable the channel to prevent furher receiving */
+ if(i == (len - 1))
+ omap3_spi_set_enable(ds,OMAP3_MCSPI_CHCTRL_DIS);
+
/* Read the data */
rxp[i] = readl(&ds->regs->channel[ds->slave.cs].rx);
}
if (flags & SPI_XFER_END) {
chconf &= ~OMAP3_MCSPI_CHCONF_FORCE;
- writel(chconf, &ds->regs->channel[ds->slave.cs].chconf);
-
- writel(0, &ds->regs->channel[ds->slave.cs].chctrl);
+ omap3_spi_write_chconf(ds,chconf);
}
return 0;
int i=0;
/*Enable SPI channel*/
- if (flags & SPI_XFER_BEGIN)
- writel(OMAP3_MCSPI_CHCTRL_EN,
- &ds->regs->channel[ds->slave.cs].chctrl);
+ omap3_spi_set_enable(ds,OMAP3_MCSPI_CHCTRL_EN);
/*set TRANSMIT-RECEIVE Mode*/
chconf &= ~OMAP3_MCSPI_CHCONF_TRM_MASK;
chconf |= OMAP3_MCSPI_CHCONF_FORCE;
- writel(chconf, &ds->regs->channel[ds->slave.cs].chconf);
+ omap3_spi_write_chconf(ds,chconf);
/*Shift in and out 1 byte at time*/
for (i=0; i < len; i++){
/* Read the data */
rxp[i] = readl(&ds->regs->channel[ds->slave.cs].rx);
}
+ /* Disable the channel */
+ omap3_spi_set_enable(ds,OMAP3_MCSPI_CHCTRL_DIS);
/*if transfer must be terminated disable the channel*/
if (flags & SPI_XFER_END) {
chconf &= ~OMAP3_MCSPI_CHCONF_FORCE;
- writel(chconf, &ds->regs->channel[ds->slave.cs].chconf);
-
- writel(0, &ds->regs->channel[ds->slave.cs].chctrl);
+ omap3_spi_write_chconf(ds,chconf);
}
return 0;
int chconf = readl(&ds->regs->channel[ds->slave.cs].chconf);
if (flags & SPI_XFER_BEGIN) {
- writel(OMAP3_MCSPI_CHCTRL_EN,
- &ds->regs->channel[ds->slave.cs].chctrl);
+ omap3_spi_set_enable(ds,OMAP3_MCSPI_CHCTRL_EN);
chconf |= OMAP3_MCSPI_CHCONF_FORCE;
- writel(chconf,
- &ds->regs->channel[ds->slave.cs].chconf);
+ omap3_spi_write_chconf(ds,chconf);
}
if (flags & SPI_XFER_END) {
chconf &= ~OMAP3_MCSPI_CHCONF_FORCE;
- writel(chconf,
- &ds->regs->channel[ds->slave.cs].chconf);
- writel(0, &ds->regs->channel[ds->slave.cs].chctrl);
+ omap3_spi_write_chconf(ds,chconf);
+ omap3_spi_set_enable(ds,OMAP3_MCSPI_CHCTRL_DIS);
}
ret = 0;
} else {
#define OMAP3_MCSPI_CHSTAT_EOT (1 << 2)
#define OMAP3_MCSPI_CHCTRL_EN (1 << 0)
+#define OMAP3_MCSPI_CHCTRL_DIS (0 << 0)
#define OMAP3_MCSPI_WAKEUPENABLE_WKEN (1 << 0)
#define CONFIG_SYS_SPI_U_BOOT_SIZE 0x40000
#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds"
+#define CONFIG_SPL_BOARD_INIT
+#define CONFIG_SPL_NAND_AM33XX_BCH
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SPL_NAND_BASE
+#define CONFIG_SPL_NAND_DRIVERS
+#define CONFIG_SPL_NAND_ECC
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \
+ CONFIG_SYS_NAND_PAGE_SIZE)
+#define CONFIG_SYS_NAND_PAGE_SIZE 2048
+#define CONFIG_SYS_NAND_OOBSIZE 64
+#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
+#define CONFIG_SYS_NAND_ECCPOS { 2, 3, 4, 5, 6, 7, 8, 9, \
+ 10, 11, 12, 13, 14, 15, 16, 17, \
+ 18, 19, 20, 21, 22, 23, 24, 25, \
+ 26, 27, 28, 29, 30, 31, 32, 33, \
+ 34, 35, 36, 37, 38, 39, 40, 41, \
+ 42, 43, 44, 45, 46, 47, 48, 49, \
+ 50, 51, 52, 53, 54, 55, 56, 57, }
+
+#define CONFIG_SYS_NAND_ECCSIZE 512
+#define CONFIG_SYS_NAND_ECCBYTES 14
+
+#define CONFIG_SYS_NAND_ECCSTEPS 4
+#define CONFIG_SYS_NAND_ECCTOTAL (CONFIG_SYS_NAND_ECCBYTES * \
+ CONFIG_SYS_NAND_ECCSTEPS)
+
+#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
+
+#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
+
/*
* 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
* 64 bytes before this address should be set aside for u-boot.img's
#define CONFIG_NET_MULTI
#define CONFIG_PHY_GIGE
#define CONFIG_PHYLIB
+#define CONFIG_PHY_ADDR 0
#define CONFIG_PHY_SMSC
+#define CONFIG_NAND
+/* NAND support */
+#ifdef CONFIG_NAND
+#define CONFIG_CMD_NAND
+#define CONFIG_NAND_OMAP_GPMC
+#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
+#define CONFIG_SYS_NAND_BASE (0x08000000) /* physical address */
+ /* to access nand at */
+ /* CS0 */
+#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND
+ devices */
+#undef CONFIG_ENV_IS_NOWHERE
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_OFFSET 0x260000 /* environment starts here */
+#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
+#endif
+
#endif /* ! __CONFIG_AM335X_EVM_H */
/* Environment information */
#define CONFIG_BOOTDELAY 10
+#define CONFIG_ZERO_BOOTDELAY_CHECK
#define CONFIG_EXTRA_ENV_SETTINGS \
"loadaddr=0x82000000\0" \
*/
#define CONFIG_NR_DRAM_BANKS 1 /* CS1 is never populated */
#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
-#define PHYS_SDRAM_1_SIZE (32 << 20) /* at least 32 MiB */
/*-----------------------------------------------------------------------
* FLASH and environment organization
*/
#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
-#define PHYS_SDRAM_1_SIZE (32 << 20) /* at least 32 MiB */
#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
/*-----------------------------------------------------------------------
*/
#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
-#define PHYS_SDRAM_1_SIZE (32 << 20) /* at least 32 meg */
#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
/*
*/
#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
-#define PHYS_SDRAM_1_SIZE (32 << 20) /* at least 32 MiB */
#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
/*
"else run userbutton_nonxm; fi;\0" \
"userbutton_xm=gpio input 4;\0" \
"userbutton_nonxm=gpio input 7;\0"
-/* "run userbutton" will return 1 (false) if is pressed and 0 (false) if not */
+/* "run userbutton" will return 1 (false) if pressed and 0 (true) if not */
#define CONFIG_BOOTCOMMAND \
"mmc dev ${mmcdev}; if mmc rescan; then " \
"if run userbutton; then " \
*/
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
-#define PHYS_SDRAM_1_SIZE (32 << 20) /* at least 32 MiB */
#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
#define CONFIG_ENV_IS_NOWHERE 1
*/
#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
-#define PHYS_SDRAM_1_SIZE (32 << 20) /* at least 32 MiB */
#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
#define CONFIG_SYS_TEXT_BASE 0x80008000
*/
#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
-#define PHYS_SDRAM_1_SIZE (32 << 20) /* at least 32 meg */
#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
/*--------------------------------------------------------------------------*/
*/
#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
-#define PHYS_SDRAM_1_SIZE (32 << 20) /* at least 32 MiB */
#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
/*-----------------------------------------------------------------------
*/
#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
-#define PHYS_SDRAM_1_SIZE (32 << 20) /* at least 32 MiB */
#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
/*-----------------------------------------------------------------------
*/
#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
-#define PHYS_SDRAM_1_SIZE (32 << 20) /* at least 32 MiB */
#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
/*
* I2C EEPROM
*/
#if !(defined(__KERNEL_STRICT_NAMES) || defined(__ASSEMBLY__))
-
/*
* The I2C EEPROM on the TAM3517 contains
* mac address and production data
unsigned char _rev[100];
};
-#define TAM3517_READ_MAC_FROM_EEPROM \
-do { \
- struct tam3517_module_info info;\
- char buf[80], ethname[20]; \
- int i; \
+#define TAM3517_READ_EEPROM(info, ret) \
+do { \
i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); \
if (eeprom_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, \
- (void *)&info, sizeof(info))) \
- break; \
+ (void *)info, sizeof(*info))) \
+ ret = 1; \
+ else \
+ ret = 0; \
+} while (0)
+
+#define TAM3517_READ_MAC_FROM_EEPROM(info) \
+do { \
+ char buf[80], ethname[20]; \
+ int i; \
memset(buf, 0, sizeof(buf)); \
- for (i = 0 ; i < ARRAY_SIZE(info.eth_addr); i++) { \
+ for (i = 0 ; i < ARRAY_SIZE((info)->eth_addr); i++) { \
sprintf(buf, "%02X:%02X:%02X:%02X:%02X:%02X", \
- info.eth_addr[i][5], \
- info.eth_addr[i][4], \
- info.eth_addr[i][3], \
- info.eth_addr[i][2], \
- info.eth_addr[i][1], \
- info.eth_addr[i][0]); \
+ (info)->eth_addr[i][5], \
+ (info)->eth_addr[i][4], \
+ (info)->eth_addr[i][3], \
+ (info)->eth_addr[i][2], \
+ (info)->eth_addr[i][1], \
+ (info)->eth_addr[i][0]); \
\
if (i) \
sprintf(ethname, "eth%daddr", i); \
setenv(ethname, buf); \
} \
} while (0)
+
+/* The following macros are taken from Technexion's documentation */
+#define TAM3517_sequence_number(info) \
+ ((info)->sequence_number % 0x1000000000000LL)
+#define TAM3517_week_of_year(info) (((info)->sequence_number >> 48) % 0x100)
+#define TAM3517_year(info) ((info)->sequence_number >> 56)
+#define TAM3517_revision_fixed(info) ((info)->revision % 0x100)
+#define TAM3517_revision_major(info) (((info)->revision >> 8) % 0x100)
+#define TAM3517_revision_tn(info) ((info)->revision >> 16)
+
+#define TAM3517_PRINT_SOM_INFO(info) \
+do { \
+ printf("Vendor:%s\n", (info)->customer); \
+ printf("SOM: %s\n", (info)->product); \
+ printf("SeqNr: %02llu%02llu%012llu\n", \
+ TAM3517_year(info), \
+ TAM3517_week_of_year(info), \
+ TAM3517_sequence_number(info)); \
+ printf("Rev: TN%u %u.%u\n", \
+ TAM3517_revision_tn(info), \
+ TAM3517_revision_major(info), \
+ TAM3517_revision_fixed(info)); \
+} while (0)
+
#endif
#endif /* __TAM3517_H */
/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
-#define PHYS_SDRAM_1_SIZE (128 << 20) /* at least 128 MiB */
#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
/* NAND and environment organization */
int twl6035_i2c_write_u8(u8 chip_no, u8 val, u8 reg);
int twl6035_i2c_read_u8(u8 chip_no, u8 *val, u8 reg);
void twl6035_init_settings(void);
-void twl6035_mmc1_poweron_ldo(void);
+int twl6035_mmc1_poweron_ldo(void);
projects / karo-tx-uboot.git / commitdiff