a320evb FA526 (ARM920T-like) (a320 SoC)
+Eric Cooper <ecc@cmu.edu>
+
+ dockstar ARM926EJS (Kirkwood SoC)
+
George G. Davis <gdavis@mvista.com>
assabet SA1100
_bss_end_ofs:
.word _end - _start
-.globl _datarel_start_ofs
-_datarel_start_ofs:
- .word __datarel_start - _start
-
-.globl _datarelrolocal_start_ofs
-_datarelrolocal_start_ofs:
- .word __datarelrolocal_start - _start
-
-.globl _datarellocal_start_ofs
-_datarellocal_start_ofs:
- .word __datarellocal_start - _start
-
-.globl _datarelro_start_ofs
-_datarelro_start_ofs:
- .word __datarelro_start - _start
-
-.globl _rel_dyn_start_ofs
-_rel_dyn_start_ofs:
- .word __rel_dyn_start - _start
-
-.globl _rel_dyn_end_ofs
-_rel_dyn_end_ofs:
- .word __rel_dyn_end - _start
-
-.globl _dynsym_start_ofs
-_dynsym_start_ofs:
- .word __dynsym_start - _start
-
/* IRQ stack memory (calculated at run-time) + 8 bytes */
.globl IRQ_STACK_START_IN
IRQ_STACK_START_IN:
ldr r3, _rel_dyn_end_ofs /* r3 <- rel dyn end ofs */
add r3, r3, r0 /* r3 <- rel dyn end in FLASH */
fixloop:
- ldr r0, [r2] /* r0 <- location to fix up, IN FLASH! */
- add r0, r0, r9 /* r0 <- location to fix up in RAM */
+ ldr r0, [r2] /* r0 <- location to fix up, IN FLASH! */
+ add r0, r0, r9 /* r0 <- location to fix up in RAM */
ldr r1, [r2, #4]
and r8, r1, #0xff
- cmp r8, #23 /* relative fixup? */
+ cmp r8, #23 /* relative fixup? */
beq fixrel
- cmp r8, #2 /* absolute fixup? */
+ cmp r8, #2 /* absolute fixup? */
beq fixabs
/* ignore unknown type of fixup */
b fixnext
mov r1, r1, LSR #4 /* r1 <- symbol index in .dynsym */
add r1, r10, r1 /* r1 <- address of symbol in table */
ldr r1, [r1, #4] /* r1 <- symbol value */
- add r1, r1, r9 /* r1 <- relocated sym addr */
+ add r1, r9 /* r1 <- relocated sym addr */
b fixnext
fixrel:
/* relative fix: increase location by offset */
add r1, r1, r9
fixnext:
str r1, [r0]
- add r2, r2, #8 /* each rel.dyn entry is 8 bytes */
+ add r2, r2, #8 /* each rel.dyn entry is 8 bytes */
cmp r2, r3
blo fixloop
#endif
.word board_init_r - _start
#endif
+_rel_dyn_start_ofs:
+ .word __rel_dyn_start - _start
+_rel_dyn_end_ofs:
+ .word __rel_dyn_end - _start
+_dynsym_start_ofs:
+ .word __dynsym_start - _start
+
#ifdef CONFIG_ENABLE_MMU
_mmu_table_base:
.word mmu_table
/*
* These are defined in the board-specific linker script.
+ * Subtracting _start from them lets the linker put their
+ * relative position in the executable instead of leaving
+ * them null.
*/
-.globl _bss_start
-_bss_start:
- .word __bss_start
+.globl _bss_start_ofs
+_bss_start_ofs:
+ .word __bss_start - _start
-.globl _bss_end
-_bss_end:
- .word _end
+.globl _bss_end_ofs
+_bss_end_ofs:
+ .word _end - _start
#ifdef CONFIG_USE_IRQ
/* IRQ stack memory (calculated at run-time) */
IRQ_STACK_START_IN:
.word 0x0badc0de
-.globl _datarel_start
-_datarel_start:
- .word __datarel_start
-
-.globl _datarelrolocal_start
-_datarelrolocal_start:
- .word __datarelrolocal_start
-
-.globl _datarellocal_start
-_datarellocal_start:
- .word __datarellocal_start
-
-.globl _datarelro_start
-_datarelro_start:
- .word __datarelro_start
-
-.globl _got_start
-_got_start:
- .word __got_start
-
-.globl _got_end
-_got_end:
- .word __got_end
-
/*
* the actual reset code
*/
adr r0, _start
ldr r2, _TEXT_BASE
- ldr r3, _bss_start
- sub r2, r3, r2 /* r2 <- size of armboot */
- add r2, r0, r2 /* r2 <- source end address */
+ ldr r3, _bss_start_ofs
+ add r2, r0, r3 /* r2 <- source end address */
cmp r0, r6
beq clear_bss
blo copy_loop
#ifndef CONFIG_PRELOADER
- /* fix got entries */
- ldr r1, _TEXT_BASE /* Text base */
- mov r0, r7 /* reloc addr */
- ldr r2, _got_start /* addr in Flash */
- ldr r3, _got_end /* addr in Flash */
- sub r3, r3, r1
- add r3, r3, r0
- sub r2, r2, r1
- add r2, r2, r0
-
+ /*
+ * fix .rel.dyn relocations
+ */
+ ldr r0, _TEXT_BASE /* r0 <- Text base */
+ sub r9, r7, r0 /* r9 <- relocation offset */
+ ldr r10, _dynsym_start_ofs /* r10 <- sym table ofs */
+ add r10, r10, r0 /* r10 <- sym table in FLASH */
+ ldr r2, _rel_dyn_start_ofs /* r2 <- rel dyn start ofs */
+ add r2, r2, r0 /* r2 <- rel dyn start in FLASH */
+ ldr r3, _rel_dyn_end_ofs /* r3 <- rel dyn end ofs */
+ add r3, r3, r0 /* r3 <- rel dyn end in FLASH */
fixloop:
- ldr r4, [r2]
- sub r4, r4, r1
- add r4, r4, r0
- str r4, [r2]
- add r2, r2, #4
+ ldr r0, [r2] /* r0 <- location to fix up, IN FLASH! */
+ add r0, r0, r9 /* r0 <- location to fix up in RAM */
+ ldr r1, [r2, #4]
+ and r8, r1, #0xff
+ cmp r8, #23 /* relative fixup? */
+ beq fixrel
+ cmp r8, #2 /* absolute fixup? */
+ beq fixabs
+ /* ignore unknown type of fixup */
+ b fixnext
+fixabs:
+ /* absolute fix: set location to (offset) symbol value */
+ mov r1, r1, LSR #4 /* r1 <- symbol index in .dynsym */
+ add r1, r10, r1 /* r1 <- address of symbol in table */
+ ldr r1, [r1, #4] /* r1 <- symbol value */
+ add r1, r9 /* r1 <- relocated sym addr */
+ b fixnext
+fixrel:
+ /* relative fix: increase location by offset */
+ ldr r1, [r0]
+ add r1, r1, r9
+fixnext:
+ str r1, [r0]
+ add r2, r2, #8 /* each rel.dyn entry is 8 bytes */
cmp r2, r3
blo fixloop
#endif
clear_bss:
#ifndef CONFIG_PRELOADER
- ldr r0, _bss_start
- ldr r1, _bss_end
+ ldr r0, _bss_start_ofs
+ ldr r1, _bss_end_ofs
ldr r3, _TEXT_BASE /* Text base */
mov r4, r7 /* reloc addr */
- sub r0, r0, r3
add r0, r0, r4
- sub r1, r1, r3
add r1, r1, r4
mov r2, #0x00000000 /* clear */
* We are done. Do not return, instead branch to second part of board
* initialization, now running from RAM.
*/
- ldr r0, _TEXT_BASE
- ldr r2, _board_init_r
- sub r2, r2, r0
- add r2, r2, r7 /* position from board_init_r in RAM */
+ ldr r0, _board_init_r_ofs
+ adr r1, _start
+ add lr, r0, r1
+ add lr, lr, r9
/* setup parameters for board_init_r */
mov r0, r5 /* gd_t */
mov r1, r7 /* dest_addr */
/* jump to it ... */
- mov lr, r2
mov pc, lr
-_board_init_r: .word board_init_r
+_board_init_r_ofs:
+ .word board_init_r - _start
+
+_rel_dyn_start_ofs:
+ .word __rel_dyn_start - _start
+_rel_dyn_end_ofs:
+ .word __rel_dyn_end - _start
+_dynsym_start_ofs:
+ .word __dynsym_start - _start
/*
*************************************************************************
. = ALIGN(4);
.data : {
- *(.data)
- __datarel_start = .;
- *(.data.rel)
- __datarelrolocal_start = .;
- *(.data.rel.ro.local)
- __datarellocal_start = .;
- *(.data.rel.local)
- __datarelro_start = .;
- *(.data.rel.ro)
}
- __got_start = .;
. = ALIGN(4);
- .got : { *(.got) }
- __got_end = .;
. = .;
__u_boot_cmd_start = .;
.u_boot_cmd : { *(.u_boot_cmd) }
__u_boot_cmd_end = .;
. = ALIGN(4);
- __bss_start = .;
- .bss (NOLOAD) : { *(.bss) . = ALIGN(4); }
- _end = .;
+
+ .rel.dyn : {
+ __rel_dyn_start = .;
+ *(.rel*)
+ __rel_dyn_end = .;
+ }
+
+ .dynsym : {
+ __dynsym_start = .;
+ *(.dynsym)
+ }
+
+ .bss __rel_dyn_start (OVERLAY) : {
+ __bss_start = .;
+ *(.bss)
+ . = ALIGN(4);
+ _end = .;
+ }
+
+ /DISCARD/ : { *(.dynstr*) }
+ /DISCARD/ : { *(.dynamic*) }
+ /DISCARD/ : { *(.plt*) }
+ /DISCARD/ : { *(.interp*) }
+ /DISCARD/ : { *(.gnu*) }
}
/*
* These are defined in the board-specific linker script.
+ * Subtracting _start from them lets the linker put their
+ * relative position in the executable instead of leaving
+ * them null.
*/
-.globl _bss_start
-_bss_start:
- .word __bss_start
+.globl _bss_start_ofs
+_bss_start_ofs:
+ .word __bss_start - _start
-.globl _bss_end
-_bss_end:
- .word _end
+.globl _bss_end_ofs
+_bss_end_ofs:
+ .word _end - _start
#ifdef CONFIG_USE_IRQ
/* IRQ stack memory (calculated at run-time) */
IRQ_STACK_START_IN:
.word 0x0badc0de
-.globl _datarel_start
-_datarel_start:
- .word __datarel_start
-
-.globl _datarelrolocal_start
-_datarelrolocal_start:
- .word __datarelrolocal_start
-
-.globl _datarellocal_start
-_datarellocal_start:
- .word __datarellocal_start
-
-.globl _datarelro_start
-_datarelro_start:
- .word __datarelro_start
-
-.globl _got_start
-_got_start:
- .word __got_start
-
-.globl _got_end
-_got_end:
- .word __got_end
-
/*
* the actual start code
*/
adr r0, _start
ldr r2, _TEXT_BASE
- ldr r3, _bss_start
- sub r2, r3, r2 /* r2 <- size of armboot */
- add r2, r0, r2 /* r2 <- source end address */
+ ldr r3, _bss_start_ofs
+ add r2, r0, r3 /* r2 <- source end address */
cmp r0, r6
beq clear_bss
blo copy_loop
#ifndef CONFIG_PRELOADER
- /* fix got entries */
- ldr r1, _TEXT_BASE /* Text base */
- mov r0, r7 /* reloc addr */
- ldr r2, _got_start /* addr in Flash */
- ldr r3, _got_end /* addr in Flash */
- sub r3, r3, r1
- add r3, r3, r0
- sub r2, r2, r1
- add r2, r2, r0
-
+ /*
+ * fix .rel.dyn relocations
+ */
+ ldr r0, _TEXT_BASE /* r0 <- Text base */
+ sub r9, r7, r0 /* r9 <- relocation offset */
+ ldr r10, _dynsym_start_ofs /* r10 <- sym table ofs */
+ add r10, r10, r0 /* r10 <- sym table in FLASH */
+ ldr r2, _rel_dyn_start_ofs /* r2 <- rel dyn start ofs */
+ add r2, r2, r0 /* r2 <- rel dyn start in FLASH */
+ ldr r3, _rel_dyn_end_ofs /* r3 <- rel dyn end ofs */
+ add r3, r3, r0 /* r3 <- rel dyn end in FLASH */
fixloop:
- ldr r4, [r2]
- sub r4, r4, r1
- add r4, r4, r0
- str r4, [r2]
- add r2, r2, #4
+ ldr r0, [r2] /* r0 <- location to fix up, IN FLASH! */
+ add r0, r0, r9 /* r0 <- location to fix up in RAM */
+ ldr r1, [r2, #4]
+ and r8, r1, #0xff
+ cmp r8, #23 /* relative fixup? */
+ beq fixrel
+ cmp r8, #2 /* absolute fixup? */
+ beq fixabs
+ /* ignore unknown type of fixup */
+ b fixnext
+fixabs:
+ /* absolute fix: set location to (offset) symbol value */
+ mov r1, r1, LSR #4 /* r1 <- symbol index in .dynsym */
+ add r1, r10, r1 /* r1 <- address of symbol in table */
+ ldr r1, [r1, #4] /* r1 <- symbol value */
+ add r1, r9 /* r1 <- relocated sym addr */
+ b fixnext
+fixrel:
+ /* relative fix: increase location by offset */
+ ldr r1, [r0]
+ add r1, r1, r9
+fixnext:
+ str r1, [r0]
+ add r2, r2, #8 /* each rel.dyn entry is 8 bytes */
cmp r2, r3
blo fixloop
#endif
clear_bss:
#ifndef CONFIG_PRELOADER
- ldr r0, _bss_start
- ldr r1, _bss_end
+ ldr r0, _bss_start_ofs
+ ldr r1, _bss_end_ofs
ldr r3, _TEXT_BASE /* Text base */
mov r4, r7 /* reloc addr */
- sub r0, r0, r3
add r0, r0, r4
- sub r1, r1, r3
add r1, r1, r4
mov r2, #0x00000000 /* clear */
* initialization, now running from RAM.
*/
#ifdef CONFIG_NAND_SPL
- ldr pc, _nand_boot
+ ldr r0, _nand_boot_ofs
+ mov pc, r0
-_nand_boot: .word nand_boot
+_nand_boot_ofs:
+ .word nand_boot
#else
- ldr r0, _TEXT_BASE
- ldr r2, _board_init_r
- sub r2, r2, r0
- add r2, r2, r7 /* position from board_init_r in RAM */
+ ldr r0, _board_init_r_ofs
+ adr r1, _start
+ add lr, r0, r1
+ add lr, lr, r9
/* setup parameters for board_init_r */
mov r0, r5 /* gd_t */
mov r1, r7 /* dest_addr */
/* jump to it ... */
- mov lr, r2
mov pc, lr
-_board_init_r: .word board_init_r
+_board_init_r_ofs:
+ .word board_init_r - _start
#endif
+_rel_dyn_start_ofs:
+ .word __rel_dyn_start - _start
+_rel_dyn_end_ofs:
+ .word __rel_dyn_end - _start
+_dynsym_start_ofs:
+ .word __dynsym_start - _start
+
/*
*************************************************************************
*
. = ALIGN(4);
.data : {
*(.data)
- __datarel_start = .;
- *(.data.rel)
- __datarelrolocal_start = .;
- *(.data.rel.ro.local)
- __datarellocal_start = .;
- *(.data.rel.local)
- __datarelro_start = .;
- *(.data.rel.ro)
}
- __got_start = .;
. = ALIGN(4);
- .got : { *(.got) }
- __got_end = .;
. = .;
__u_boot_cmd_start = .;
.u_boot_cmd : { *(.u_boot_cmd) }
__u_boot_cmd_end = .;
. = ALIGN(4);
- __bss_start = .;
- .bss (NOLOAD) : { *(.bss) . = ALIGN(4); }
- _end = .;
+
+ .rel.dyn : {
+ __rel_dyn_start = .;
+ *(.rel*)
+ __rel_dyn_end = .;
+ }
+
+ .dynsym : {
+ __dynsym_start = .;
+ *(.dynsym)
+ }
+
+ .bss __rel_dyn_start (OVERLAY) : {
+ __bss_start = .;
+ *(.bss)
+ . = ALIGN(4);
+ _end = .;
+ }
+
+ /DISCARD/ : { *(.dynstr*) }
+ /DISCARD/ : { *(.dynamic*) }
+ /DISCARD/ : { *(.plt*) }
+ /DISCARD/ : { *(.interp*) }
+ /DISCARD/ : { *(.gnu*) }
}
/*
* These are defined in the board-specific linker script.
+ * Subtracting _start from them lets the linker put their
+ * relative position in the executable instead of leaving
+ * them null.
*/
-.globl _bss_start
-_bss_start:
- .word __bss_start
+.globl _bss_start_ofs
+_bss_start_ofs:
+ .word __bss_start - _start
-.globl _bss_end
-_bss_end:
- .word _end
+.globl _bss_end_ofs
+_bss_end_ofs:
+ .word _end - _start
#ifdef CONFIG_USE_IRQ
/* IRQ stack memory (calculated at run-time) */
IRQ_STACK_START_IN:
.word 0x0badc0de
-.globl _datarel_start
-_datarel_start:
- .word __datarel_start
-
-.globl _datarelrolocal_start
-_datarelrolocal_start:
- .word __datarelrolocal_start
-
-.globl _datarellocal_start
-_datarellocal_start:
- .word __datarellocal_start
-
-.globl _datarelro_start
-_datarelro_start:
- .word __datarelro_start
-
-.globl _got_start
-_got_start:
- .word __got_start
-
-.globl _got_end
-_got_end:
- .word __got_end
-
/*
* the actual reset code
*/
adr r0, _start
ldr r2, _TEXT_BASE
- ldr r3, _bss_start
- sub r2, r3, r2 /* r2 <- size of armboot */
- add r2, r0, r2 /* r2 <- source end address */
+ ldr r3, _bss_start_ofs
+ add r2, r0, r3 /* r2 <- source end address */
cmp r0, r6
beq clear_bss
blo copy_loop
#ifndef CONFIG_PRELOADER
- /* fix got entries */
- ldr r1, _TEXT_BASE /* Text base */
- mov r0, r7 /* reloc addr */
- ldr r2, _got_start /* addr in Flash */
- ldr r3, _got_end /* addr in Flash */
- sub r3, r3, r1
- add r3, r3, r0
- sub r2, r2, r1
- add r2, r2, r0
-
+ /*
+ * fix .rel.dyn relocations
+ */
+ ldr r0, _TEXT_BASE /* r0 <- Text base */
+ sub r9, r7, r0 /* r9 <- relocation offset */
+ ldr r10, _dynsym_start_ofs /* r10 <- sym table ofs */
+ add r10, r10, r0 /* r10 <- sym table in FLASH */
+ ldr r2, _rel_dyn_start_ofs /* r2 <- rel dyn start ofs */
+ add r2, r2, r0 /* r2 <- rel dyn start in FLASH */
+ ldr r3, _rel_dyn_end_ofs /* r3 <- rel dyn end ofs */
+ add r3, r3, r0 /* r3 <- rel dyn end in FLASH */
fixloop:
- ldr r4, [r2]
- sub r4, r4, r1
- add r4, r4, r0
- str r4, [r2]
- add r2, r2, #4
+ ldr r0, [r2] /* r0 <- location to fix up, IN FLASH! */
+ add r0, r0, r9 /* r0 <- location to fix up in RAM */
+ ldr r1, [r2, #4]
+ and r8, r1, #0xff
+ cmp r8, #23 /* relative fixup? */
+ beq fixrel
+ cmp r8, #2 /* absolute fixup? */
+ beq fixabs
+ /* ignore unknown type of fixup */
+ b fixnext
+fixabs:
+ /* absolute fix: set location to (offset) symbol value */
+ mov r1, r1, LSR #4 /* r1 <- symbol index in .dynsym */
+ add r1, r10, r1 /* r1 <- address of symbol in table */
+ ldr r1, [r1, #4] /* r1 <- symbol value */
+ add r1, r9 /* r1 <- relocated sym addr */
+ b fixnext
+fixrel:
+ /* relative fix: increase location by offset */
+ ldr r1, [r0]
+ add r1, r1, r9
+fixnext:
+ str r1, [r0]
+ add r2, r2, #8 /* each rel.dyn entry is 8 bytes */
cmp r2, r3
blo fixloop
#endif
clear_bss:
#ifndef CONFIG_PRELOADER
- ldr r0, _bss_start
- ldr r1, _bss_end
+ ldr r0, _bss_start_ofs
+ ldr r1, _bss_end_ofs
ldr r3, _TEXT_BASE /* Text base */
mov r4, r7 /* reloc addr */
- sub r0, r0, r3
add r0, r0, r4
- sub r1, r1, r3
add r1, r1, r4
mov r2, #0x00000000 /* clear */
cmp r0, r1
bne clbss_l
+ bl coloured_LED_init
+ bl red_LED_on
#endif
/*
* initialization, now running from RAM.
*/
#ifdef CONFIG_NAND_SPL
- ldr pc, _nand_boot
+ ldr r0, _nand_boot_ofs
+ mov pc, r0
-_nand_boot: .word nand_boot
+_nand_boot_ofs:
+ .word nand_boot
#else
- ldr r0, _TEXT_BASE
- ldr r2, _board_init_r
- sub r2, r2, r0
- add r2, r2, r7 /* position from board_init_r in RAM */
+ ldr r0, _board_init_r_ofs
+ adr r1, _start
+ add lr, r0, r1
+ add lr, lr, r9
/* setup parameters for board_init_r */
mov r0, r5 /* gd_t */
mov r1, r7 /* dest_addr */
/* jump to it ... */
- mov lr, r2
mov pc, lr
-_board_init_r: .word board_init_r
+_board_init_r_ofs:
+ .word board_init_r - _start
#endif
+_rel_dyn_start_ofs:
+ .word __rel_dyn_start - _start
+_rel_dyn_end_ofs:
+ .word __rel_dyn_end - _start
+_dynsym_start_ofs:
+ .word __dynsym_start - _start
+
/*
*************************************************************************
*
. = ALIGN(4);
.data : {
*(.data)
- __datarel_start = .;
- *(.data.rel)
- __datarelrolocal_start = .;
- *(.data.rel.ro.local)
- __datarellocal_start = .;
- *(.data.rel.local)
- __datarelro_start = .;
- *(.data.rel.ro)
}
- __got_start = .;
. = ALIGN(4);
- .got : { *(.got) }
- __got_end = .;
. = .;
__u_boot_cmd_start = .;
.u_boot_cmd : { *(.u_boot_cmd) }
__u_boot_cmd_end = .;
. = ALIGN(4);
- __bss_start = .;
- .bss (NOLOAD) : { *(.bss) . = ALIGN(4); }
- _end = .;
+
+ .rel.dyn : {
+ __rel_dyn_start = .;
+ *(.rel*)
+ __rel_dyn_end = .;
+ }
+
+ .dynsym : {
+ __dynsym_start = .;
+ *(.dynsym)
+ }
+
+ .bss __rel_dyn_start (OVERLAY) : {
+ __bss_start = .;
+ *(.bss)
+ . = ALIGN(4);
+ _end = .;
+ }
+
+ /DISCARD/ : { *(.dynstr*) }
+ /DISCARD/ : { *(.dynamic*) }
+ /DISCARD/ : { *(.plt*) }
+ /DISCARD/ : { *(.interp*) }
+ /DISCARD/ : { *(.gnu*) }
}
* Copyright (c) 2002 Gary Jennejohn <garyj@denx.de>
* Copyright (c) 2003 Richard Woodruff <r-woodruff2@ti.com>
* Copyright (c) 2003 Kshitij <kshitij@ti.com>
+ * Copyright (c) 2010 Albert Aribaud <albert.aribaud@free.fr>
*
* See file CREDITS for list of people who contributed to this
* project.
.balignl 16,0xdeadbeef
+_vectors_end:
/*
*************************************************************************
/*
* These are defined in the board-specific linker script.
+ * Subtracting _start from them lets the linker put their
+ * relative position in the executable instead of leaving
+ * them null.
*/
-.globl _bss_start
-_bss_start:
- .word __bss_start
+.globl _bss_start_ofs
+_bss_start_ofs:
+ .word __bss_start - _start
-.globl _bss_end
-_bss_end:
- .word _end
+.globl _bss_end_ofs
+_bss_end_ofs:
+ .word _end - _start
#ifdef CONFIG_USE_IRQ
/* IRQ stack memory (calculated at run-time) */
IRQ_STACK_START_IN:
.word 0x0badc0de
-.globl _datarel_start
-_datarel_start:
- .word __datarel_start
-
-.globl _datarelrolocal_start
-_datarelrolocal_start:
- .word __datarelrolocal_start
-
-.globl _datarellocal_start
-_datarellocal_start:
- .word __datarellocal_start
-
-.globl _datarelro_start
-_datarelro_start:
- .word __datarelro_start
-
-.globl _got_start
-_got_start:
- .word __got_start
-
-.globl _got_end
-_got_end:
- .word __got_end
-
/*
* the actual reset code
*/
adr r0, _start
ldr r2, _TEXT_BASE
- ldr r3, _bss_start
- sub r2, r3, r2 /* r2 <- size of armboot */
- add r2, r0, r2 /* r2 <- source end address */
+ ldr r3, _bss_start_ofs
+ add r2, r0, r3 /* r2 <- source end address */
cmp r0, r6
beq clear_bss
blo copy_loop
#ifndef CONFIG_PRELOADER
- /* fix got entries */
- ldr r1, _TEXT_BASE /* Text base */
- mov r0, r7 /* reloc addr */
- ldr r2, _got_start /* addr in Flash */
- ldr r3, _got_end /* addr in Flash */
- sub r3, r3, r1
- add r3, r3, r0
- sub r2, r2, r1
- add r2, r2, r0
-
+ /*
+ * fix .rel.dyn relocations
+ */
+ ldr r0, _TEXT_BASE /* r0 <- Text base */
+ sub r9, r7, r0 /* r9 <- relocation offset */
+ ldr r10, _dynsym_start_ofs /* r10 <- sym table ofs */
+ add r10, r10, r0 /* r10 <- sym table in FLASH */
+ ldr r2, _rel_dyn_start_ofs /* r2 <- rel dyn start ofs */
+ add r2, r2, r0 /* r2 <- rel dyn start in FLASH */
+ ldr r3, _rel_dyn_end_ofs /* r3 <- rel dyn end ofs */
+ add r3, r3, r0 /* r3 <- rel dyn end in FLASH */
fixloop:
- ldr r4, [r2]
- sub r4, r4, r1
- add r4, r4, r0
- str r4, [r2]
- add r2, r2, #4
+ ldr r0, [r2] /* r0 <- location to fix up, IN FLASH! */
+ add r0, r0, r9 /* r0 <- location to fix up in RAM */
+ ldr r1, [r2, #4]
+ and r8, r1, #0xff
+ cmp r8, #23 /* relative fixup? */
+ beq fixrel
+ cmp r8, #2 /* absolute fixup? */
+ beq fixabs
+ /* ignore unknown type of fixup */
+ b fixnext
+fixabs:
+ /* absolute fix: set location to (offset) symbol value */
+ mov r1, r1, LSR #4 /* r1 <- symbol index in .dynsym */
+ add r1, r10, r1 /* r1 <- address of symbol in table */
+ ldr r1, [r1, #4] /* r1 <- symbol value */
+ add r1, r9 /* r1 <- relocated sym addr */
+ b fixnext
+fixrel:
+ /* relative fix: increase location by offset */
+ ldr r1, [r0]
+ add r1, r1, r9
+fixnext:
+ str r1, [r0]
+ add r2, r2, #8 /* each rel.dyn entry is 8 bytes */
cmp r2, r3
blo fixloop
#endif
clear_bss:
#ifndef CONFIG_PRELOADER
- ldr r0, _bss_start
- ldr r1, _bss_end
+ ldr r0, _bss_start_ofs
+ ldr r1, _bss_end_ofs
ldr r3, _TEXT_BASE /* Text base */
mov r4, r7 /* reloc addr */
- sub r0, r0, r3
add r0, r0, r4
- sub r1, r1, r3
add r1, r1, r4
mov r2, #0x00000000 /* clear */
clbss_l:str r2, [r0] /* clear loop... */
add r0, r0, #4
cmp r0, r1
- bne clbss_l
+ blo clbss_l
#endif
/*
_nand_boot: .word nand_boot
#else
- ldr r0, _TEXT_BASE
- ldr r2, _board_init_r
- sub r2, r2, r0
- add r2, r2, r7 /* position from board_init_r in RAM */
+ ldr r0, _board_init_r_ofs
+ adr r1, _start
+ add lr, r0, r1
+ add lr, lr, r9
/* setup parameters for board_init_r */
mov r0, r5 /* gd_t */
mov r1, r7 /* dest_addr */
/* jump to it ... */
- mov lr, r2
mov pc, lr
-_board_init_r: .word board_init_r
+_board_init_r_ofs:
+ .word board_init_r - _start
#endif
+_rel_dyn_start_ofs:
+ .word __rel_dyn_start - _start
+_rel_dyn_end_ofs:
+ .word __rel_dyn_end - _start
+_dynsym_start_ofs:
+ .word __dynsym_start - _start
+
/*
*************************************************************************
*
. = ALIGN(4);
.data : {
*(.data)
- __datarel_start = .;
- *(.data.rel)
- __datarelrolocal_start = .;
- *(.data.rel.ro.local)
- __datarellocal_start = .;
- *(.data.rel.local)
- __datarelro_start = .;
- *(.data.rel.ro)
}
- __got_start = .;
. = ALIGN(4);
- .got : { *(.got) }
- __got_end = .;
. = .;
__u_boot_cmd_start = .;
.u_boot_cmd : { *(.u_boot_cmd) }
__u_boot_cmd_end = .;
. = ALIGN(4);
- __bss_start = .;
- .bss (NOLOAD) : { *(.bss) . = ALIGN(4); }
- _end = .;
+
+ .rel.dyn : {
+ __rel_dyn_start = .;
+ *(.rel*)
+ __rel_dyn_end = .;
+ }
+
+ .dynsym : {
+ __dynsym_start = .;
+ *(.dynsym)
+ }
+
+ .bss __rel_dyn_start (OVERLAY) : {
+ __bss_start = .;
+ *(.bss)
+ . = ALIGN(4);
+ _end = .;
+ }
+
+ /DISCARD/ : { *(.dynstr*) }
+ /DISCARD/ : { *(.dynamic*) }
+ /DISCARD/ : { *(.plt*) }
+ /DISCARD/ : { *(.interp*) }
+ /DISCARD/ : { *(.gnu*) }
}
/*
* These are defined in the board-specific linker script.
+ * Subtracting _start from them lets the linker put their
+ * relative position in the executable instead of leaving
+ * them null.
*/
-.globl _bss_start
-_bss_start:
- .word __bss_start
+.globl _bss_start_ofs
+_bss_start_ofs:
+ .word __bss_start - _start
-.globl _bss_end
-_bss_end:
- .word _end
+.globl _bss_end_ofs
+_bss_end_ofs:
+ .word _end - _start
#ifdef CONFIG_USE_IRQ
/* IRQ stack memory (calculated at run-time) */
IRQ_STACK_START_IN:
.word 0x0badc0de
-.globl _datarel_start
-_datarel_start:
- .word __datarel_start
-
-.globl _datarelrolocal_start
-_datarelrolocal_start:
- .word __datarelrolocal_start
-
-.globl _datarellocal_start
-_datarellocal_start:
- .word __datarellocal_start
-
-.globl _datarelro_start
-_datarelro_start:
- .word __datarelro_start
-
-.globl _got_start
-_got_start:
- .word __got_start
-
-.globl _got_end
-_got_end:
- .word __got_end
-
/*
* the actual reset code
*/
adr r0, _start
ldr r2, _TEXT_BASE
- ldr r3, _bss_start
- sub r2, r3, r2 /* r2 <- size of armboot */
- add r2, r0, r2 /* r2 <- source end address */
+ ldr r3, _bss_start_ofs
+ add r2, r0, r3 /* r2 <- source end address */
cmp r0, r6
beq clear_bss
blo copy_loop
#ifndef CONFIG_PRELOADER
- /* fix got entries */
- ldr r1, _TEXT_BASE /* Text base */
- mov r0, r7 /* reloc addr */
- ldr r2, _got_start /* addr in Flash */
- ldr r3, _got_end /* addr in Flash */
- sub r3, r3, r1
- add r3, r3, r0
- sub r2, r2, r1
- add r2, r2, r0
-
+ /*
+ * fix .rel.dyn relocations
+ */
+ ldr r0, _TEXT_BASE /* r0 <- Text base */
+ sub r9, r7, r0 /* r9 <- relocation offset */
+ ldr r10, _dynsym_start_ofs /* r10 <- sym table ofs */
+ add r10, r10, r0 /* r10 <- sym table in FLASH */
+ ldr r2, _rel_dyn_start_ofs /* r2 <- rel dyn start ofs */
+ add r2, r2, r0 /* r2 <- rel dyn start in FLASH */
+ ldr r3, _rel_dyn_end_ofs /* r3 <- rel dyn end ofs */
+ add r3, r3, r0 /* r3 <- rel dyn end in FLASH */
fixloop:
- ldr r4, [r2]
- sub r4, r4, r1
- add r4, r4, r0
- str r4, [r2]
- add r2, r2, #4
+ ldr r0, [r2] /* r0 <- location to fix up, IN FLASH! */
+ add r0, r0, r9 /* r0 <- location to fix up in RAM */
+ ldr r1, [r2, #4]
+ and r8, r1, #0xff
+ cmp r8, #23 /* relative fixup? */
+ beq fixrel
+ cmp r8, #2 /* absolute fixup? */
+ beq fixabs
+ /* ignore unknown type of fixup */
+ b fixnext
+fixabs:
+ /* absolute fix: set location to (offset) symbol value */
+ mov r1, r1, LSR #4 /* r1 <- symbol index in .dynsym */
+ add r1, r10, r1 /* r1 <- address of symbol in table */
+ ldr r1, [r1, #4] /* r1 <- symbol value */
+ add r1, r9 /* r1 <- relocated sym addr */
+ b fixnext
+fixrel:
+ /* relative fix: increase location by offset */
+ ldr r1, [r0]
+ add r1, r1, r9
+fixnext:
+ str r1, [r0]
+ add r2, r2, #8 /* each rel.dyn entry is 8 bytes */
cmp r2, r3
blo fixloop
#endif
clear_bss:
#ifndef CONFIG_PRELOADER
- ldr r0, _bss_start
- ldr r1, _bss_end
+ ldr r0, _bss_start_ofs
+ ldr r1, _bss_end_ofs
ldr r3, _TEXT_BASE /* Text base */
mov r4, r7 /* reloc addr */
- sub r0, r0, r3
add r0, r0, r4
- sub r1, r1, r3
add r1, r1, r4
mov r2, #0x00000000 /* clear */
* We are done. Do not return, instead branch to second part of board
* initialization, now running from RAM.
*/
- ldr r0, _TEXT_BASE
- ldr r2, _board_init_r
- sub r2, r2, r0
- add r2, r2, r7 /* position from board_init_r in RAM */
+#ifdef CONFIG_NAND_SPL
+ ldr r0, _nand_boot_ofs
+ mov pc, r0
+
+_nand_boot_ofs:
+ .word nand_boot
+#else
+ ldr r0, _board_init_r_ofs
+ adr r1, _start
+ add lr, r0, r1
+ add lr, lr, r9
/* setup parameters for board_init_r */
mov r0, r5 /* gd_t */
mov r1, r7 /* dest_addr */
/* jump to it ... */
- mov lr, r2
mov pc, lr
-_board_init_r: .word board_init_r
+_board_init_r_ofs:
+ .word board_init_r - _start
+#endif
+
+_rel_dyn_start_ofs:
+ .word __rel_dyn_start - _start
+_rel_dyn_end_ofs:
+ .word __rel_dyn_end - _start
+_dynsym_start_ofs:
+ .word __dynsym_start - _start
/*
*************************************************************************
. = ALIGN(4);
.data : {
*(.data)
- __datarel_start = .;
- *(.data.rel)
- __datarelrolocal_start = .;
- *(.data.rel.ro.local)
- __datarellocal_start = .;
- *(.data.rel.local)
- __datarelro_start = .;
- *(.data.rel.ro)
}
- __got_start = .;
. = ALIGN(4);
- .got : { *(.got) }
- __got_end = .;
. = .;
__u_boot_cmd_start = .;
.u_boot_cmd : { *(.u_boot_cmd) }
__u_boot_cmd_end = .;
. = ALIGN(4);
- __bss_start = .;
- .bss (NOLOAD) : { *(.bss) . = ALIGN(4); }
- _end = .;
+
+ .rel.dyn : {
+ __rel_dyn_start = .;
+ *(.rel*)
+ __rel_dyn_end = .;
+ }
+
+ .dynsym : {
+ __dynsym_start = .;
+ *(.dynsym)
+ }
+
+ .bss __rel_dyn_start (OVERLAY) : {
+ __bss_start = .;
+ *(.bss)
+ . = ALIGN(4);
+ _end = .;
+ }
+
+ /DISCARD/ : { *(.dynstr*) }
+ /DISCARD/ : { *(.dynamic*) }
+ /DISCARD/ : { *(.plt*) }
+ /DISCARD/ : { *(.interp*) }
+ /DISCARD/ : { *(.gnu*) }
}
#include <asm/arch/sys_proto.h>
#include <asm/sizes.h>
+DECLARE_GLOBAL_DATA_PTR;
+
/*
* Routine: s_init
* Description: Does early system init of muxing and clocks.
*/
int dram_init(void)
{
- DECLARE_GLOBAL_DATA_PTR;
gd->ram_size = sdram_size();
/*
* These are defined in the board-specific linker script.
+ * Subtracting _start from them lets the linker put their
+ * relative position in the executable instead of leaving
+ * them null.
*/
-.globl _bss_start
-_bss_start:
- .word __bss_start
+.globl _bss_start_ofs
+_bss_start_ofs:
+ .word __bss_start - _start
-.globl _bss_end
-_bss_end:
- .word _end
+.globl _bss_end_ofs
+_bss_end_ofs:
+ .word _end - _start
#ifdef CONFIG_USE_IRQ
/* IRQ stack memory (calculated at run-time) */
IRQ_STACK_START_IN:
.word 0x0badc0de
-.globl _datarel_start
-_datarel_start:
- .word __datarel_start
-
-.globl _datarelrolocal_start
-_datarelrolocal_start:
- .word __datarelrolocal_start
-
-.globl _datarellocal_start
-_datarellocal_start:
- .word __datarellocal_start
-
-.globl _datarelro_start
-_datarelro_start:
- .word __datarelro_start
-
-.globl _got_start
-_got_start:
- .word __got_start
-
-.globl _got_end
-_got_end:
- .word __got_end
-
/*
* the actual reset code
*/
adr r0, _start
ldr r2, _TEXT_BASE
- ldr r3, _bss_start
- sub r2, r3, r2 /* r2 <- size of armboot */
- add r2, r0, r2 /* r2 <- source end address */
+ ldr r3, _bss_start_ofs
+ add r2, r0, r3 /* r2 <- source end address */
cmp r0, r6
beq clear_bss
blo copy_loop
#ifndef CONFIG_PRELOADER
- /* fix got entries */
- ldr r1, _TEXT_BASE /* Text base */
- mov r0, r7 /* reloc addr */
- ldr r2, _got_start /* addr in Flash */
- ldr r3, _got_end /* addr in Flash */
- sub r3, r3, r1
- add r3, r3, r0
- sub r2, r2, r1
- add r2, r2, r0
-
+ /*
+ * fix .rel.dyn relocations
+ */
+ ldr r0, _TEXT_BASE /* r0 <- Text base */
+ sub r9, r7, r0 /* r9 <- relocation offset */
+ ldr r10, _dynsym_start_ofs /* r10 <- sym table ofs */
+ add r10, r10, r0 /* r10 <- sym table in FLASH */
+ ldr r2, _rel_dyn_start_ofs /* r2 <- rel dyn start ofs */
+ add r2, r2, r0 /* r2 <- rel dyn start in FLASH */
+ ldr r3, _rel_dyn_end_ofs /* r3 <- rel dyn end ofs */
+ add r3, r3, r0 /* r3 <- rel dyn end in FLASH */
fixloop:
- ldr r4, [r2]
- sub r4, r4, r1
- add r4, r4, r0
- str r4, [r2]
- add r2, r2, #4
+ ldr r0, [r2] /* r0 <- location to fix up, IN FLASH! */
+ add r0, r0, r9 /* r0 <- location to fix up in RAM */
+ ldr r1, [r2, #4]
+ and r8, r1, #0xff
+ cmp r8, #23 /* relative fixup? */
+ beq fixrel
+ cmp r8, #2 /* absolute fixup? */
+ beq fixabs
+ /* ignore unknown type of fixup */
+ b fixnext
+fixabs:
+ /* absolute fix: set location to (offset) symbol value */
+ mov r1, r1, LSR #4 /* r1 <- symbol index in .dynsym */
+ add r1, r10, r1 /* r1 <- address of symbol in table */
+ ldr r1, [r1, #4] /* r1 <- symbol value */
+ add r1, r9 /* r1 <- relocated sym addr */
+ b fixnext
+fixrel:
+ /* relative fix: increase location by offset */
+ ldr r1, [r0]
+ add r1, r1, r9
+fixnext:
+ str r1, [r0]
+ add r2, r2, #8 /* each rel.dyn entry is 8 bytes */
cmp r2, r3
blo fixloop
#endif
clear_bss:
#ifndef CONFIG_PRELOADER
- ldr r0, _bss_start
- ldr r1, _bss_end
+ ldr r0, _bss_start_ofs
+ ldr r1, _bss_end_ofs
ldr r3, _TEXT_BASE /* Text base */
mov r4, r7 /* reloc addr */
- sub r0, r0, r3
add r0, r0, r4
- sub r1, r1, r3
add r1, r1, r4
mov r2, #0x00000000 /* clear */
* We are done. Do not return, instead branch to second part of board
* initialization, now running from RAM.
*/
- ldr r0, _TEXT_BASE
- ldr r2, _board_init_r
- sub r2, r2, r0
- add r2, r2, r7 /* position from board_init_r in RAM */
+ ldr r0, _board_init_r_ofs
+ adr r1, _start
+ add lr, r0, r1
+ add lr, lr, r9
/* setup parameters for board_init_r */
mov r0, r5 /* gd_t */
mov r1, r7 /* dest_addr */
/* jump to it ... */
- mov lr, r2
mov pc, lr
-_board_init_r: .word board_init_r
+_board_init_r_ofs:
+ .word board_init_r - _start
+_rel_dyn_start_ofs:
+ .word __rel_dyn_start - _start
+_rel_dyn_end_ofs:
+ .word __rel_dyn_end - _start
+_dynsym_start_ofs:
+ .word __dynsym_start - _start
/****************************************************************************/
/* */
. = ALIGN(4);
.data : {
*(.data)
- __datarel_start = .;
- *(.data.rel)
- __datarelrolocal_start = .;
- *(.data.rel.ro.local)
- __datarellocal_start = .;
- *(.data.rel.local)
- __datarelro_start = .;
- *(.data.rel.ro)
}
- __got_start = .;
. = ALIGN(4);
- .got : { *(.got) }
- __got_end = .;
. = .;
__u_boot_cmd_start = .;
.u_boot_cmd : { *(.u_boot_cmd) }
__u_boot_cmd_end = .;
. = ALIGN(4);
- __bss_start = .;
- .bss (NOLOAD) : { *(.bss) . = ALIGN(4); }
- _end = .;
+
+ .rel.dyn : {
+ __rel_dyn_start = .;
+ *(.rel*)
+ __rel_dyn_end = .;
+ }
+
+ .dynsym : {
+ __dynsym_start = .;
+ *(.dynsym)
+ }
+
+ .bss __rel_dyn_start (OVERLAY) : {
+ __bss_start = .;
+ *(.bss)
+ . = ALIGN(4);
+ _end = .;
+ }
+
+ /DISCARD/ : { *(.dynstr*) }
+ /DISCARD/ : { *(.dynamic*) }
+ /DISCARD/ : { *(.plt*) }
+ /DISCARD/ : { *(.interp*) }
+ /DISCARD/ : { *(.gnu*) }
}
/*
* These are defined in the board-specific linker script.
+ * Subtracting _start from them lets the linker put their
+ * relative position in the executable instead of leaving
+ * them null.
*/
-.globl _bss_start
-_bss_start:
- .word __bss_start
+.globl _bss_start_ofs
+_bss_start_ofs:
+ .word __bss_start - _start
-.globl _bss_end
-_bss_end:
- .word _end
+.globl _bss_end_ofs
+_bss_end_ofs:
+ .word _end - _start
#ifdef CONFIG_USE_IRQ
/* IRQ stack memory (calculated at run-time) */
IRQ_STACK_START_IN:
.word 0x0badc0de
-.globl _datarel_start
-_datarel_start:
- .word __datarel_start
-
-.globl _datarelrolocal_start
-_datarelrolocal_start:
- .word __datarelrolocal_start
-
-.globl _datarellocal_start
-_datarellocal_start:
- .word __datarellocal_start
-
-.globl _datarelro_start
-_datarelro_start:
- .word __datarelro_start
-
-.globl _got_start
-_got_start:
- .word __got_start
-
-.globl _got_end
-_got_end:
- .word __got_end
-
/*
* the actual reset code
*/
adr r0, _start
ldr r2, _TEXT_BASE
- ldr r3, _bss_start
- sub r2, r3, r2 /* r2 <- size of armboot */
- add r2, r0, r2 /* r2 <- source end address */
+ ldr r3, _bss_start_ofs
+ add r2, r0, r3 /* r2 <- source end address */
cmp r0, r6
beq clear_bss
blo copy_loop
#ifndef CONFIG_PRELOADER
- /* fix got entries */
- ldr r1, _TEXT_BASE /* Text base */
- mov r0, r7 /* reloc addr */
- ldr r2, _got_start /* addr in Flash */
- ldr r3, _got_end /* addr in Flash */
- sub r3, r3, r1
- add r3, r3, r0
- sub r2, r2, r1
- add r2, r2, r0
-
+ /*
+ * fix .rel.dyn relocations
+ */
+ ldr r0, _TEXT_BASE /* r0 <- Text base */
+ sub r9, r7, r0 /* r9 <- relocation offset */
+ ldr r10, _dynsym_start_ofs /* r10 <- sym table ofs */
+ add r10, r10, r0 /* r10 <- sym table in FLASH */
+ ldr r2, _rel_dyn_start_ofs /* r2 <- rel dyn start ofs */
+ add r2, r2, r0 /* r2 <- rel dyn start in FLASH */
+ ldr r3, _rel_dyn_end_ofs /* r3 <- rel dyn end ofs */
+ add r3, r3, r0 /* r3 <- rel dyn end in FLASH */
fixloop:
- ldr r4, [r2]
- sub r4, r4, r1
- add r4, r4, r0
- str r4, [r2]
- add r2, r2, #4
+ ldr r0, [r2] /* r0 <- location to fix up, IN FLASH! */
+ add r0, r0, r9 /* r0 <- location to fix up in RAM */
+ ldr r1, [r2, #4]
+ and r8, r1, #0xff
+ cmp r8, #23 /* relative fixup? */
+ beq fixrel
+ cmp r8, #2 /* absolute fixup? */
+ beq fixabs
+ /* ignore unknown type of fixup */
+ b fixnext
+fixabs:
+ /* absolute fix: set location to (offset) symbol value */
+ mov r1, r1, LSR #4 /* r1 <- symbol index in .dynsym */
+ add r1, r10, r1 /* r1 <- address of symbol in table */
+ ldr r1, [r1, #4] /* r1 <- symbol value */
+ add r1, r9 /* r1 <- relocated sym addr */
+ b fixnext
+fixrel:
+ /* relative fix: increase location by offset */
+ ldr r1, [r0]
+ add r1, r1, r9
+fixnext:
+ str r1, [r0]
+ add r2, r2, #8 /* each rel.dyn entry is 8 bytes */
cmp r2, r3
blo fixloop
#endif
clear_bss:
#ifndef CONFIG_PRELOADER
- ldr r0, _bss_start
- ldr r1, _bss_end
+ ldr r0, _bss_start_ofs
+ ldr r1, _bss_end_ofs
ldr r3, _TEXT_BASE /* Text base */
mov r4, r7 /* reloc addr */
- sub r0, r0, r3
add r0, r0, r4
- sub r1, r1, r3
add r1, r1, r4
mov r2, #0x00000000 /* clear */
* We are done. Do not return, instead branch to second part of board
* initialization, now running from RAM.
*/
- ldr r0, _TEXT_BASE
- ldr r2, _board_init_r
- sub r2, r2, r0
- add r2, r2, r7 /* position from board_init_r in RAM */
+ ldr r0, _board_init_r_ofs
+ adr r1, _start
+ add lr, r0, r1
+ add lr, lr, r9
/* setup parameters for board_init_r */
mov r0, r5 /* gd_t */
mov r1, r7 /* dest_addr */
/* jump to it ... */
- mov lr, r2
mov pc, lr
-_board_init_r: .word board_init_r
+_board_init_r_ofs:
+ .word board_init_r - _start
+
+_rel_dyn_start_ofs:
+ .word __rel_dyn_start - _start
+_rel_dyn_end_ofs:
+ .word __rel_dyn_end - _start
+_dynsym_start_ofs:
+ .word __dynsym_start - _start
/*
*************************************************************************
. = ALIGN(4);
.data : {
*(.data)
- __datarel_start = .;
- *(.data.rel)
- __datarelrolocal_start = .;
- *(.data.rel.ro.local)
- __datarellocal_start = .;
- *(.data.rel.local)
- __datarelro_start = .;
- *(.data.rel.ro)
}
- __got_start = .;
. = ALIGN(4);
- .got : { *(.got) }
- __got_end = .;
. = .;
__u_boot_cmd_start = .;
.u_boot_cmd : { *(.u_boot_cmd) }
__u_boot_cmd_end = .;
. = ALIGN(4);
- __bss_start = .;
- .bss (NOLOAD) : { *(.bss) . = ALIGN(4); }
- _end = .;
+
+ .rel.dyn : {
+ __rel_dyn_start = .;
+ *(.rel*)
+ __rel_dyn_end = .;
+ }
+
+ .dynsym : {
+ __dynsym_start = .;
+ *(.dynsym)
+ }
+
+ .bss __rel_dyn_start (OVERLAY) : {
+ __bss_start = .;
+ *(.bss)
+ . = ALIGN(4);
+ _end = .;
+ }
+
+ /DISCARD/ : { *(.dynstr*) }
+ /DISCARD/ : { *(.dynamic*) }
+ /DISCARD/ : { *(.plt*) }
+ /DISCARD/ : { *(.interp*) }
+ /DISCARD/ : { *(.gnu*) }
}
/*
* These are defined in the board-specific linker script.
+ * Subtracting _start from them lets the linker put their
+ * relative position in the executable instead of leaving
+ * them null.
*/
-.globl _bss_start
-_bss_start:
- .word __bss_start
+.globl _bss_start_ofs
+_bss_start_ofs:
+ .word __bss_start - _start
-.globl _bss_end
-_bss_end:
- .word _end
+.globl _bss_end_ofs
+_bss_end_ofs:
+ .word _end - _start
#ifdef CONFIG_USE_IRQ
/* IRQ stack memory (calculated at run-time) */
IRQ_STACK_START_IN:
.word 0x0badc0de
-.globl _datarel_start
-_datarel_start:
- .word __datarel_start
-
-.globl _datarelrolocal_start
-_datarelrolocal_start:
- .word __datarelrolocal_start
-
-.globl _datarellocal_start
-_datarellocal_start:
- .word __datarellocal_start
-
-.globl _datarelro_start
-_datarelro_start:
- .word __datarelro_start
-
-.globl _got_start
-_got_start:
- .word __got_start
-
-.globl _got_end
-_got_end:
- .word __got_end
-
/*
* the actual reset code
*/
adr r0, _start
ldr r2, _TEXT_BASE
- ldr r3, _bss_start
- sub r2, r3, r2 /* r2 <- size of armboot */
- add r2, r0, r2 /* r2 <- source end address */
+ ldr r3, _bss_start_ofs
+ add r2, r0, r3 /* r2 <- source end address */
cmp r0, r6
beq clear_bss
blo copy_loop
#ifndef CONFIG_PRELOADER
- /* fix got entries */
- ldr r1, _TEXT_BASE /* Text base */
- mov r0, r7 /* reloc addr */
- ldr r2, _got_start /* addr in Flash */
- ldr r3, _got_end /* addr in Flash */
- sub r3, r3, r1
- add r3, r3, r0
- sub r2, r2, r1
- add r2, r2, r0
-
+ /*
+ * fix .rel.dyn relocations
+ */
+ ldr r0, _TEXT_BASE /* r0 <- Text base */
+ sub r9, r7, r0 /* r9 <- relocation offset */
+ ldr r10, _dynsym_start_ofs /* r10 <- sym table ofs */
+ add r10, r10, r0 /* r10 <- sym table in FLASH */
+ ldr r2, _rel_dyn_start_ofs /* r2 <- rel dyn start ofs */
+ add r2, r2, r0 /* r2 <- rel dyn start in FLASH */
+ ldr r3, _rel_dyn_end_ofs /* r3 <- rel dyn end ofs */
+ add r3, r3, r0 /* r3 <- rel dyn end in FLASH */
fixloop:
- ldr r4, [r2]
- sub r4, r4, r1
- add r4, r4, r0
- str r4, [r2]
- add r2, r2, #4
+ ldr r0, [r2] /* r0 <- location to fix up, IN FLASH! */
+ add r0, r0, r9 /* r0 <- location to fix up in RAM */
+ ldr r1, [r2, #4]
+ and r8, r1, #0xff
+ cmp r8, #23 /* relative fixup? */
+ beq fixrel
+ cmp r8, #2 /* absolute fixup? */
+ beq fixabs
+ /* ignore unknown type of fixup */
+ b fixnext
+fixabs:
+ /* absolute fix: set location to (offset) symbol value */
+ mov r1, r1, LSR #4 /* r1 <- symbol index in .dynsym */
+ add r1, r10, r1 /* r1 <- address of symbol in table */
+ ldr r1, [r1, #4] /* r1 <- symbol value */
+ add r1, r9 /* r1 <- relocated sym addr */
+ b fixnext
+fixrel:
+ /* relative fix: increase location by offset */
+ ldr r1, [r0]
+ add r1, r1, r9
+fixnext:
+ str r1, [r0]
+ add r2, r2, #8 /* each rel.dyn entry is 8 bytes */
cmp r2, r3
blo fixloop
#endif
-/*
- now copy to sram the interrupt vector
-*/
- adr r0, real_vectors
- add r2, r0, #1024
- ldr r1, =0x0c000000
- add r1, r1, #0x08
-vector_copy_loop:
- ldmia r0!, {r3-r10}
- stmia r1!, {r3-r10}
- cmp r0, r2
- blo vector_copy_loop
clear_bss:
#ifndef CONFIG_PRELOADER
- ldr r0, _bss_start
- ldr r1, _bss_end
+ ldr r0, _bss_start_ofs
+ ldr r1, _bss_end_ofs
ldr r3, _TEXT_BASE /* Text base */
mov r4, r7 /* reloc addr */
- sub r0, r0, r3
add r0, r0, r4
- sub r1, r1, r3
add r1, r1, r4
mov r2, #0x00000000 /* clear */
* We are done. Do not return, instead branch to second part of board
* initialization, now running from RAM.
*/
- ldr r0, _TEXT_BASE
- ldr r2, _board_init_r
- sub r2, r2, r0
- add r2, r2, r7 /* position from board_init_r in RAM */
+ ldr r0, _board_init_r_ofs
+ adr r1, _start
+ add lr, r0, r1
+ add lr, lr, r9
/* setup parameters for board_init_r */
mov r0, r5 /* gd_t */
mov r1, r7 /* dest_addr */
/* jump to it ... */
- mov lr, r2
mov pc, lr
-_board_init_r: .word board_init_r
+_board_init_r_ofs:
+ .word board_init_r - _start
+
+_rel_dyn_start_ofs:
+ .word __rel_dyn_start - _start
+_rel_dyn_end_ofs:
+ .word __rel_dyn_end - _start
+_dynsym_start_ofs:
+ .word __dynsym_start - _start
/*
*************************************************************************
. = ALIGN(4);
.data : {
*(.data)
- __datarel_start = .;
- *(.data.rel)
- __datarelrolocal_start = .;
- *(.data.rel.ro.local)
- __datarellocal_start = .;
- *(.data.rel.local)
- __datarelro_start = .;
- *(.data.rel.ro)
}
- __got_start = .;
. = ALIGN(4);
- .got : { *(.got) }
- __got_end = .;
. = .;
__u_boot_cmd_start = .;
.u_boot_cmd : { *(.u_boot_cmd) }
__u_boot_cmd_end = .;
. = ALIGN(4);
- __bss_start = .;
- .bss (NOLOAD) : { *(.bss) . = ALIGN(4); }
- _end = .;
+
+ .rel.dyn : {
+ __rel_dyn_start = .;
+ *(.rel*)
+ __rel_dyn_end = .;
+ }
+
+ .dynsym : {
+ __dynsym_start = .;
+ *(.dynsym)
+ }
+
+ .bss __rel_dyn_start (OVERLAY) : {
+ __bss_start = .;
+ *(.bss)
+ . = ALIGN(4);
+ _end = .;
+ }
+
+ /DISCARD/ : { *(.dynstr*) }
+ /DISCARD/ : { *(.dynamic*) }
+ /DISCARD/ : { *(.plt*) }
+ /DISCARD/ : { *(.interp*) }
+ /DISCARD/ : { *(.gnu*) }
}
/*
* These are defined in the board-specific linker script.
+ * Subtracting _start from them lets the linker put their
+ * relative position in the executable instead of leaving
+ * them null.
*/
-.globl _bss_start
-_bss_start:
- .word __bss_start
+.globl _bss_start_ofs
+_bss_start_ofs:
+ .word __bss_start - _start
-.globl _bss_end
-_bss_end:
- .word _end
+.globl _bss_end_ofs
+_bss_end_ofs:
+ .word _end - _start
#ifdef CONFIG_USE_IRQ
/* IRQ stack memory (calculated at run-time) */
IRQ_STACK_START_IN:
.word 0x0badc0de
-.globl _datarel_start
-_datarel_start:
- .word __datarel_start
-
-.globl _datarelrolocal_start
-_datarelrolocal_start:
- .word __datarelrolocal_start
-
-.globl _datarellocal_start
-_datarellocal_start:
- .word __datarellocal_start
-
-.globl _datarelro_start
-_datarelro_start:
- .word __datarelro_start
-
-.globl _got_start
-_got_start:
- .word __got_start
-
-.globl _got_end
-_got_end:
- .word __got_end
-
/*
* the actual reset code
*/
adr r0, _start
ldr r2, _TEXT_BASE
- ldr r3, _bss_start
- sub r2, r3, r2 /* r2 <- size of armboot */
- add r2, r0, r2 /* r2 <- source end address */
+ ldr r3, _bss_start_ofs
+ add r2, r0, r3 /* r2 <- source end address */
cmp r0, r6
beq clear_bss
blo copy_loop
#ifndef CONFIG_PRELOADER
- /* fix got entries */
- ldr r1, _TEXT_BASE /* Text base */
- mov r0, r7 /* reloc addr */
- ldr r2, _got_start /* addr in Flash */
- ldr r3, _got_end /* addr in Flash */
- sub r3, r3, r1
- add r3, r3, r0
- sub r2, r2, r1
- add r2, r2, r0
-
+ /*
+ * fix .rel.dyn relocations
+ */
+ ldr r0, _TEXT_BASE /* r0 <- Text base */
+ sub r9, r7, r0 /* r9 <- relocation offset */
+ ldr r10, _dynsym_start_ofs /* r10 <- sym table ofs */
+ add r10, r10, r0 /* r10 <- sym table in FLASH */
+ ldr r2, _rel_dyn_start_ofs /* r2 <- rel dyn start ofs */
+ add r2, r2, r0 /* r2 <- rel dyn start in FLASH */
+ ldr r3, _rel_dyn_end_ofs /* r3 <- rel dyn end ofs */
+ add r3, r3, r0 /* r3 <- rel dyn end in FLASH */
fixloop:
- ldr r4, [r2]
- sub r4, r4, r1
- add r4, r4, r0
- str r4, [r2]
- add r2, r2, #4
+ ldr r0, [r2] /* r0 <- location to fix up, IN FLASH! */
+ add r0, r0, r9 /* r0 <- location to fix up in RAM */
+ ldr r1, [r2, #4]
+ and r8, r1, #0xff
+ cmp r8, #23 /* relative fixup? */
+ beq fixrel
+ cmp r8, #2 /* absolute fixup? */
+ beq fixabs
+ /* ignore unknown type of fixup */
+ b fixnext
+fixabs:
+ /* absolute fix: set location to (offset) symbol value */
+ mov r1, r1, LSR #4 /* r1 <- symbol index in .dynsym */
+ add r1, r10, r1 /* r1 <- address of symbol in table */
+ ldr r1, [r1, #4] /* r1 <- symbol value */
+ add r1, r9 /* r1 <- relocated sym addr */
+ b fixnext
+fixrel:
+ /* relative fix: increase location by offset */
+ ldr r1, [r0]
+ add r1, r1, r9
+fixnext:
+ str r1, [r0]
+ add r2, r2, #8 /* each rel.dyn entry is 8 bytes */
cmp r2, r3
blo fixloop
#endif
clear_bss:
#ifndef CONFIG_PRELOADER
- ldr r0, _bss_start
- ldr r1, _bss_end
+ ldr r0, _bss_start_ofs
+ ldr r1, _bss_end_ofs
ldr r3, _TEXT_BASE /* Text base */
mov r4, r7 /* reloc addr */
- sub r0, r0, r3
add r0, r0, r4
- sub r1, r1, r3
add r1, r1, r4
mov r2, #0x00000000 /* clear */
* We are done. Do not return, instead branch to second part of board
* initialization, now running from RAM.
*/
- ldr r0, _TEXT_BASE
- ldr r2, _board_init_r
- sub r2, r2, r0
- add r2, r2, r7 /* position from board_init_r in RAM */
+ ldr r0, _board_init_r_ofs
+ adr r1, _start
+ add lr, r0, r1
+ add lr, lr, r9
/* setup parameters for board_init_r */
mov r0, r5 /* gd_t */
mov r1, r7 /* dest_addr */
/* jump to it ... */
- mov lr, r2
mov pc, lr
-_board_init_r: .word board_init_r
+_board_init_r_ofs:
+ .word board_init_r - _start
+
+_rel_dyn_start_ofs:
+ .word __rel_dyn_start - _start
+_rel_dyn_end_ofs:
+ .word __rel_dyn_end - _start
+_dynsym_start_ofs:
+ .word __dynsym_start - _start
/*
*************************************************************************
. = ALIGN(4);
.data : {
*(.data)
- __datarel_start = .;
- *(.data.rel)
- __datarelrolocal_start = .;
- *(.data.rel.ro.local)
- __datarellocal_start = .;
- *(.data.rel.local)
- __datarelro_start = .;
- *(.data.rel.ro)
}
- __got_start = .;
. = ALIGN(4);
- .got : { *(.got) }
- __got_end = .;
. = .;
__u_boot_cmd_start = .;
.u_boot_cmd : { *(.u_boot_cmd) }
__u_boot_cmd_end = .;
. = ALIGN(4);
- __bss_start = .;
- .bss (NOLOAD) : { *(.bss) . = ALIGN(4); }
- _end = .;
+
+ .rel.dyn : {
+ __rel_dyn_start = .;
+ *(.rel*)
+ __rel_dyn_end = .;
+ }
+
+ .dynsym : {
+ __dynsym_start = .;
+ *(.dynsym)
+ }
+
+ .bss __rel_dyn_start (OVERLAY) : {
+ __bss_start = .;
+ *(.bss)
+ . = ALIGN(4);
+ _end = .;
+ }
+
+ /DISCARD/ : { *(.dynstr*) }
+ /DISCARD/ : { *(.dynamic*) }
+ /DISCARD/ : { *(.plt*) }
+ /DISCARD/ : { *(.interp*) }
+ /DISCARD/ : { *(.gnu*) }
}
--- /dev/null
+#
+# Copyright (C) 2010 Eric C. Cooper <ecc@cmu.edu>
+#
+# Based on sheevaplug/Makefile originally written by
+# Prafulla Wadaskar <prafulla@marvell.com>
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).o
+
+COBJS := dockstar.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(call cmd_link_o_target, $(OBJS) $(SOBJS))
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
--- /dev/null
+/*
+ * Copyright (C) 2010 Eric C. Cooper <ecc@cmu.edu>
+ *
+ * Based on sheevaplug.c originally written by
+ * Prafulla Wadaskar <prafulla@marvell.com>
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#include <common.h>
+#include <miiphy.h>
+#include <asm/arch/kirkwood.h>
+#include <asm/arch/mpp.h>
+#include "dockstar.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_early_init_f(void)
+{
+ /*
+ * default gpio configuration
+ * There are maximum 64 gpios controlled through 2 sets of registers
+ * the below configuration configures mainly initial LED status
+ */
+ kw_config_gpio(DOCKSTAR_OE_VAL_LOW,
+ DOCKSTAR_OE_VAL_HIGH,
+ DOCKSTAR_OE_LOW, DOCKSTAR_OE_HIGH);
+
+ /* Multi-Purpose Pins Functionality configuration */
+ u32 kwmpp_config[] = {
+ MPP0_NF_IO2,
+ MPP1_NF_IO3,
+ MPP2_NF_IO4,
+ MPP3_NF_IO5,
+ MPP4_NF_IO6,
+ MPP5_NF_IO7,
+ MPP6_SYSRST_OUTn,
+ MPP7_GPO,
+ MPP8_UART0_RTS,
+ MPP9_UART0_CTS,
+ MPP10_UART0_TXD,
+ MPP11_UART0_RXD,
+ MPP12_SD_CLK,
+ MPP13_SD_CMD,
+ MPP14_SD_D0,
+ MPP15_SD_D1,
+ MPP16_SD_D2,
+ MPP17_SD_D3,
+ MPP18_NF_IO0,
+ MPP19_NF_IO1,
+ MPP20_GPIO,
+ MPP21_GPIO,
+ MPP22_GPIO,
+ MPP23_GPIO,
+ MPP24_GPIO,
+ MPP25_GPIO,
+ MPP26_GPIO,
+ MPP27_GPIO,
+ MPP28_GPIO,
+ MPP29_TSMP9,
+ MPP30_GPIO,
+ MPP31_GPIO,
+ MPP32_GPIO,
+ MPP33_GPIO,
+ MPP34_GPIO,
+ MPP35_GPIO,
+ MPP36_GPIO,
+ MPP37_GPIO,
+ MPP38_GPIO,
+ MPP39_GPIO,
+ MPP40_GPIO,
+ MPP41_GPIO,
+ MPP42_GPIO,
+ MPP43_GPIO,
+ MPP44_GPIO,
+ MPP45_GPIO,
+ MPP46_GPIO,
+ MPP47_GPIO,
+ MPP48_GPIO,
+ MPP49_GPIO,
+ 0
+ };
+ kirkwood_mpp_conf(kwmpp_config);
+ return 0;
+}
+
+int board_init(void)
+{
+ /*
+ * arch number of board
+ */
+ gd->bd->bi_arch_number = MACH_TYPE_DOCKSTAR;
+
+ /* address of boot parameters */
+ gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100;
+
+ return 0;
+}
+
+#ifdef CONFIG_RESET_PHY_R
+/* Configure and enable MV88E1116 PHY */
+void reset_phy(void)
+{
+ u16 reg;
+ u16 devadr;
+ char *name = "egiga0";
+
+ if (miiphy_set_current_dev(name))
+ return;
+
+ /* command to read PHY dev address */
+ if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
+ printf("Err..%s could not read PHY dev address\n",
+ __FUNCTION__);
+ return;
+ }
+
+ /*
+ * Enable RGMII delay on Tx and Rx for CPU port
+ * Ref: sec 4.7.2 of chip datasheet
+ */
+ miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
+ miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®);
+ reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
+ miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
+ miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
+
+ /* reset the phy */
+ miiphy_reset(name, devadr);
+
+ printf("88E1116 Initialized on %s\n", name);
+}
+#endif /* CONFIG_RESET_PHY_R */
+
+#define GREEN_LED (1 << 14)
+#define ORANGE_LED (1 << 15)
+#define BOTH_LEDS (GREEN_LED | ORANGE_LED)
+#define NEITHER_LED 0
+
+static void set_leds(u32 leds, u32 blinking)
+{
+ struct kwgpio_registers *r = (struct kwgpio_registers *)KW_GPIO1_BASE;
+ u32 oe = readl(&r->oe) | BOTH_LEDS;
+ writel(oe & ~leds, &r->oe); /* active low */
+ u32 bl = readl(&r->blink_en) & ~BOTH_LEDS;
+ writel(bl | blinking, &r->blink_en);
+}
+
+void show_boot_progress(int val)
+{
+ switch (val) {
+ case 15: /* booting Linux */
+ set_leds(BOTH_LEDS, NEITHER_LED);
+ break;
+ case 64: /* Ethernet initialization */
+ set_leds(GREEN_LED, GREEN_LED);
+ break;
+ default:
+ if (val < 0) /* error */
+ set_leds(ORANGE_LED, ORANGE_LED);
+ break;
+ }
+}
--- /dev/null
+/*
+ * Copyright (C) 2010 Eric C. Cooper <ecc@cmu.edu>
+ *
+ * Based on sheevaplug.h originally written by
+ * Prafulla Wadaskar <prafulla@marvell.com>
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef __DOCKSTAR_H
+#define __DOCKSTAR_H
+
+#define DOCKSTAR_OE_LOW (~(0))
+#define DOCKSTAR_OE_HIGH (~(0))
+#define DOCKSTAR_OE_VAL_LOW (1 << 29) /* USB_PWEN low */
+#define DOCKSTAR_OE_VAL_HIGH (1 << 17) /* LED pin high */
+
+/* PHY related */
+#define MV88E1116_LED_FCTRL_REG 10
+#define MV88E1116_CPRSP_CR3_REG 21
+#define MV88E1116_MAC_CTRL_REG 21
+#define MV88E1116_PGADR_REG 22
+#define MV88E1116_RGMII_TXTM_CTRL (1 << 4)
+#define MV88E1116_RGMII_RXTM_CTRL (1 << 5)
+
+#endif /* __DOCKSTAR_H */
--- /dev/null
+#
+# Copyright (C) 2010 Eric C. Cooper <ecc@cmu.edu>
+#
+# Based on sheevaplug/kwbimage.cfg originally written by
+# Prafulla Wadaskar <prafulla@marvell.com>
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+# Refer docs/README.kwimage for more details about how-to configure
+# and create kirkwood boot image
+#
+
+# Boot Media configurations
+BOOT_FROM nand
+NAND_ECC_MODE default
+NAND_PAGE_SIZE 0x0800
+
+# SOC registers configuration using bootrom header extension
+# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
+
+# Configure RGMII-0 interface pad voltage to 1.8V
+DATA 0xFFD100e0 0x1b1b1b9b
+
+#Dram initalization for SINGLE x16 CL=5 @ 400MHz
+DATA 0xFFD01400 0x43000c30 # DDR Configuration register
+# bit13-0: 0xc30 (3120 DDR2 clks refresh rate)
+# bit23-14: zero
+# bit24: 1= enable exit self refresh mode on DDR access
+# bit25: 1 required
+# bit29-26: zero
+# bit31-30: 01
+
+DATA 0xFFD01404 0x37543000 # DDR Controller Control Low
+# bit 4: 0=addr/cmd in smame cycle
+# bit 5: 0=clk is driven during self refresh, we don't care for APX
+# bit 6: 0=use recommended falling edge of clk for addr/cmd
+# bit14: 0=input buffer always powered up
+# bit18: 1=cpu lock transaction enabled
+# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
+# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
+# bit30-28: 3 required
+# bit31: 0=no additional STARTBURST delay
+
+DATA 0xFFD01408 0x22125451 # DDR Timing (Low) (active cycles value +1)
+# bit3-0: TRAS lsbs
+# bit7-4: TRCD
+# bit11- 8: TRP
+# bit15-12: TWR
+# bit19-16: TWTR
+# bit20: TRAS msb
+# bit23-21: 0x0
+# bit27-24: TRRD
+# bit31-28: TRTP
+
+DATA 0xFFD0140C 0x00000a33 # DDR Timing (High)
+# bit6-0: TRFC
+# bit8-7: TR2R
+# bit10-9: TR2W
+# bit12-11: TW2W
+# bit31-13: zero required
+
+DATA 0xFFD01410 0x0000000d # DDR Address Control
+# bit1-0: 00, Cs0width=x8
+# bit3-2: 11, Cs0size=1Gb
+# bit5-4: 00, Cs1width=nonexistent
+# bit7-6: 00, Cs1size =nonexistent
+# bit9-8: 00, Cs2width=nonexistent
+# bit11-10: 00, Cs2size =nonexistent
+# bit13-12: 00, Cs3width=nonexistent
+# bit15-14: 00, Cs3size =nonexistent
+# bit16: 0, Cs0AddrSel
+# bit17: 0, Cs1AddrSel
+# bit18: 0, Cs2AddrSel
+# bit19: 0, Cs3AddrSel
+# bit31-20: 0 required
+
+DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
+# bit0: 0, OpenPage enabled
+# bit31-1: 0 required
+
+DATA 0xFFD01418 0x00000000 # DDR Operation
+# bit3-0: 0x0, DDR cmd
+# bit31-4: 0 required
+
+DATA 0xFFD0141C 0x00000C52 # DDR Mode
+# bit2-0: 2, BurstLen=2 required
+# bit3: 0, BurstType=0 required
+# bit6-4: 4, CL=5
+# bit7: 0, TestMode=0 normal
+# bit8: 0, DLL reset=0 normal
+# bit11-9: 6, auto-precharge write recovery ????????????
+# bit12: 0, PD must be zero
+# bit31-13: 0 required
+
+DATA 0xFFD01420 0x00000040 # DDR Extended Mode
+# bit0: 0, DDR DLL enabled
+# bit1: 0, DDR drive strenght normal
+# bit2: 0, DDR ODT control lsd (disabled)
+# bit5-3: 000, required
+# bit6: 1, DDR ODT control msb, (disabled)
+# bit9-7: 000, required
+# bit10: 0, differential DQS enabled
+# bit11: 0, required
+# bit12: 0, DDR output buffer enabled
+# bit31-13: 0 required
+
+DATA 0xFFD01424 0x0000F17F # DDR Controller Control High
+# bit2-0: 111, required
+# bit3 : 1 , MBUS Burst Chop disabled
+# bit6-4: 111, required
+# bit7 : 0
+# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz
+# bit9 : 0 , no half clock cycle addition to dataout
+# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals
+# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh
+# bit15-12: 1111 required
+# bit31-16: 0 required
+
+DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values)
+DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values)
+
+DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0
+DATA 0xFFD01504 0x07FFFFF1 # CS[0]n Size
+# bit0: 1, Window enabled
+# bit1: 0, Write Protect disabled
+# bit3-2: 00, CS0 hit selected
+# bit23-4: ones, required
+# bit31-24: 0x07, Size (i.e. 128MB)
+
+DATA 0xFFD01508 0x10000000 # CS[1]n Base address to 256Mb
+DATA 0xFFD0150C 0x00000000 # CS[1]n Size, window disabled
+
+DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
+DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
+
+DATA 0xFFD01494 0x00030000 # DDR ODT Control (Low)
+DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
+# bit1-0: 00, ODT0 controlled by ODT Control (low) register above
+# bit3-2: 01, ODT1 active NEVER!
+# bit31-4: zero, required
+
+DATA 0xFFD0149C 0x0000E803 # CPU ODT Control
+DATA 0xFFD01480 0x00000001 # DDR Initialization Control
+#bit0=1, enable DDR init upon this register write
+
+# End of Header extension
+DATA 0x0 0x0
{ DAVINCI_LPSC_GPIO },
};
+#ifndef CONFIG_DA850_EVM_MAX_CPU_CLK
+#define CONFIG_DA850_EVM_MAX_CPU_CLK 300000000
+#endif
+
+/*
+ * get_board_rev() - setup to pass kernel board revision information
+ * Returns:
+ * bit[0-3] Maximum cpu clock rate supported by onboard SoC
+ * 0000b - 300 MHz
+ * 0001b - 372 MHz
+ * 0010b - 408 MHz
+ * 0011b - 456 MHz
+ */
+u32 get_board_rev(void)
+{
+ char *s;
+ u32 maxcpuclk = CONFIG_DA850_EVM_MAX_CPU_CLK;
+ u32 rev = 0;
+
+ s = getenv("maxcpuclk");
+ if (s)
+ maxcpuclk = simple_strtoul(s, NULL, 10);
+
+ if (maxcpuclk >= 456000000)
+ rev = 3;
+ else if (maxcpuclk >= 408000000)
+ rev = 2;
+ else if (maxcpuclk >= 372000000)
+ rev = 1;
+
+ return rev;
+}
+
int board_init(void)
{
#ifndef CONFIG_USE_IRQ
+++ /dev/null
-#
-# (C) Copyright 2006
-# Texas Instruments, <www.ti.com>
-#
-# Pandora uses OMAP3 (ARM-CortexA8) cpu
-# see http://www.ti.com/ for more information on Texas Instruments
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-# Physical Address:
-# 8000'0000 (bank0)
-# A000/0000 (bank1)
-# Linux-Kernel is expected to be at 8000'8000, entry 8000'8000
-# (mem base + reserved)
-
-# For use with external or internal boots.
-CONFIG_SYS_TEXT_BASE = 0x80e80000
pm9263 arm arm926ejs - ronetix at91
suen3 arm arm926ejs km_arm keymile kirkwood
rd6281a arm arm926ejs - Marvell kirkwood
+dockstar arm arm926ejs - Seagate kirkwood
jadecpu arm arm926ejs jadecpu syteco mb86r0x
mx51evk arm armv7 mx51evk freescale mx5
vision2 arm armv7 vision2 ttcontrol mx5
* TI DA830 EVM
+* TI DA850 EVM
+
* DM355 based Leopard board
* DM644x based schmoogie board
make da830evm_config
make
+* TI DA850 EVM:
+
+make da850evm_config
+make
+
* DM355 based Leopard board:
make davinci_dm355leopard_config
The programmers and UBL are always released as part of any standard TI
software release associated with an SOC.
+Environment Variables
+=====================
+
+The DA850 EVM allows the user to specify the maximum cpu clock allowed by the
+silicon, in Hz, via an environment variable "maxcpuclk".
+
+The maximum clock rate allowed depends on the silicon populated on the EVM.
+Please make sure you understand the restrictions placed on this clock in the
+device specific datasheet before setting up this variable. This information is
+passed to the Linux kernel using the ATAG_REVISION atag.
+
+If "maxcpuclk" is not defined, the configuration CONFIG_DA850_EVM_MAX_CPU_CLK
+is used to obtain this information.
+
Links
=====
6) TI DA830 EVM
http://focus.ti.com/apps/docs/gencontent.tsp?appId=1&contentId=52385
http://www.spectrumdigital.com/product_info.php?cPath=37&products_id=214
+
+7) TI DA850 EVM
+http://focus.ti.com/docs/prod/folders/print/omap-l138.html
+http://www.logicpd.com/products/development-kits/zoom-omap-l138-evm-development-kit
#include <asm/io.h>
#include <asm/arch/mmc_host_def.h>
+/* If we fail after 1 second wait, something is really bad */
+#define MAX_RETRY_MS 1000
+
static int mmc_read_data(hsmmc_t *mmc_base, char *buf, unsigned int size);
static int mmc_write_data(hsmmc_t *mmc_base, const char *buf, unsigned int siz);
static struct mmc hsmmc_dev[2];
void mmc_init_stream(hsmmc_t *mmc_base)
{
+ ulong start;
writel(readl(&mmc_base->con) | INIT_INITSTREAM, &mmc_base->con);
writel(MMC_CMD0, &mmc_base->cmd);
- while (!(readl(&mmc_base->stat) & CC_MASK))
- ;
+ start = get_timer(0);
+ while (!(readl(&mmc_base->stat) & CC_MASK)) {
+ if (get_timer(0) - start > MAX_RETRY_MS) {
+ printf("%s: timedout waiting for cc!\n", __func__);
+ return;
+ }
+ }
writel(CC_MASK, &mmc_base->stat)
;
writel(MMC_CMD0, &mmc_base->cmd)
;
- while (!(readl(&mmc_base->stat) & CC_MASK))
- ;
+ start = get_timer(0);
+ while (!(readl(&mmc_base->stat) & CC_MASK)) {
+ if (get_timer(0) - start > MAX_RETRY_MS) {
+ printf("%s: timedout waiting for cc2!\n", __func__);
+ return;
+ }
+ }
writel(readl(&mmc_base->con) & ~INIT_INITSTREAM, &mmc_base->con);
}
hsmmc_t *mmc_base = (hsmmc_t *)mmc->priv;
unsigned int reg_val;
unsigned int dsor;
+ ulong start;
mmc_board_init(mmc_base);
writel(readl(&mmc_base->sysconfig) | MMC_SOFTRESET,
&mmc_base->sysconfig);
- while ((readl(&mmc_base->sysstatus) & RESETDONE) == 0)
- ;
+ start = get_timer(0);
+ while ((readl(&mmc_base->sysstatus) & RESETDONE) == 0) {
+ if (get_timer(0) - start > MAX_RETRY_MS) {
+ printf("%s: timedout waiting for cc2!\n", __func__);
+ return TIMEOUT;
+ }
+ }
writel(readl(&mmc_base->sysctl) | SOFTRESETALL, &mmc_base->sysctl);
- while ((readl(&mmc_base->sysctl) & SOFTRESETALL) != 0x0)
- ;
+ start = get_timer(0);
+ while ((readl(&mmc_base->sysctl) & SOFTRESETALL) != 0x0) {
+ if (get_timer(0) - start > MAX_RETRY_MS) {
+ printf("%s: timedout waiting for softresetall!\n",
+ __func__);
+ return TIMEOUT;
+ }
+ }
writel(DTW_1_BITMODE | SDBP_PWROFF | SDVS_3V0, &mmc_base->hctl);
writel(readl(&mmc_base->capa) | VS30_3V0SUP | VS18_1V8SUP,
&mmc_base->capa);
(ICE_STOP | DTO_15THDTO | CEN_DISABLE));
mmc_reg_out(&mmc_base->sysctl, ICE_MASK | CLKD_MASK,
(dsor << CLKD_OFFSET) | ICE_OSCILLATE);
- while ((readl(&mmc_base->sysctl) & ICS_MASK) == ICS_NOTREADY)
- ;
+ start = get_timer(0);
+ while ((readl(&mmc_base->sysctl) & ICS_MASK) == ICS_NOTREADY) {
+ if (get_timer(0) - start > MAX_RETRY_MS) {
+ printf("%s: timedout waiting for ics!\n", __func__);
+ return TIMEOUT;
+ }
+ }
writel(readl(&mmc_base->sysctl) | CEN_ENABLE, &mmc_base->sysctl);
writel(readl(&mmc_base->hctl) | SDBP_PWRON, &mmc_base->hctl);
{
hsmmc_t *mmc_base = (hsmmc_t *)mmc->priv;
unsigned int flags, mmc_stat;
- unsigned int retry = 0x100000;
+ ulong start;
-
- while ((readl(&mmc_base->pstate) & DATI_MASK) == DATI_CMDDIS)
- ;
+ start = get_timer(0);
+ while ((readl(&mmc_base->pstate) & DATI_MASK) == DATI_CMDDIS) {
+ if (get_timer(0) - start > MAX_RETRY_MS) {
+ printf("%s: timedout waiting for cmddis!\n", __func__);
+ return TIMEOUT;
+ }
+ }
writel(0xFFFFFFFF, &mmc_base->stat);
- while (readl(&mmc_base->stat))
- ;
+ start = get_timer(0);
+ while (readl(&mmc_base->stat)) {
+ if (get_timer(0) - start > MAX_RETRY_MS) {
+ printf("%s: timedout waiting for stat!\n", __func__);
+ return TIMEOUT;
+ }
+ }
/*
* CMDREG
* CMDIDX[13:8] : Command index
writel(cmd->cmdarg, &mmc_base->arg);
writel((cmd->cmdidx << 24) | flags, &mmc_base->cmd);
+ start = get_timer(0);
do {
mmc_stat = readl(&mmc_base->stat);
- retry--;
- } while ((mmc_stat == 0) && (retry > 0));
-
- if (retry == 0) {
- printf("%s : timeout: No status update\n", __func__);
- return TIMEOUT;
- }
+ if (get_timer(0) - start > MAX_RETRY_MS) {
+ printf("%s : timeout: No status update\n", __func__);
+ return TIMEOUT;
+ }
+ } while (!mmc_stat);
if ((mmc_stat & IE_CTO) != 0)
return TIMEOUT;
count /= 4;
while (size) {
+ ulong start = get_timer(0);
do {
mmc_stat = readl(&mmc_base->stat);
+ if (get_timer(0) - start > MAX_RETRY_MS) {
+ printf("%s: timedout waiting for status!\n",
+ __func__);
+ return TIMEOUT;
+ }
} while (mmc_stat == 0);
if ((mmc_stat & ERRI_MASK) != 0)
count /= 4;
while (size) {
+ ulong start = get_timer(0);
do {
mmc_stat = readl(&mmc_base->stat);
+ if (get_timer(0) - start > MAX_RETRY_MS) {
+ printf("%s: timedout waiting for status!\n",
+ __func__);
+ return TIMEOUT;
+ }
} while (mmc_stat == 0);
if ((mmc_stat & ERRI_MASK) != 0)
{
hsmmc_t *mmc_base = (hsmmc_t *)mmc->priv;
unsigned int dsor = 0;
+ ulong start;
/* configue bus width */
switch (mmc->bus_width) {
mmc_reg_out(&mmc_base->sysctl, ICE_MASK | CLKD_MASK,
(dsor << CLKD_OFFSET) | ICE_OSCILLATE);
- while ((readl(&mmc_base->sysctl) & ICS_MASK) == ICS_NOTREADY)
- ;
+ start = get_timer(0);
+ while ((readl(&mmc_base->sysctl) & ICS_MASK) == ICS_NOTREADY) {
+ if (get_timer(0) - start > MAX_RETRY_MS) {
+ printf("%s: timedout waiting for ics!\n", __func__);
+ return;
+ }
+ }
writel(readl(&mmc_base->sysctl) | CEN_ENABLE, &mmc_base->sysctl);
}
#include <usb.h>
#include <asm/io.h>
#include <malloc.h>
+#include <watchdog.h>
#include "ehci.h"
int ret = 0;
cmd = ehci_readl(&hcor->or_usbcmd);
- cmd |= CMD_RESET;
+ cmd = (cmd & ~CMD_RUN) | CMD_RESET;
ehci_writel(&hcor->or_usbcmd, cmd);
ret = handshake((uint32_t *)&hcor->or_usbcmd, CMD_RESET, 0, 250 * 1000);
if (ret < 0) {
token = hc32_to_cpu(vtd->qt_token);
if (!(token & 0x80))
break;
+ WATCHDOG_RESET();
} while (get_timer(ts) < CONFIG_SYS_HZ);
/* Disable async schedule. */
break;
default:
dev->status = USB_ST_CRC_ERR;
+ if ((token & 0x40) == 0x40)
+ dev->status |= USB_ST_STALLED;
break;
}
dev->act_len = length - ((token >> 16) & 0x7fff);
hccr = (struct ehci_hccr *)(CONFIG_SYS_PPC4XX_USB_ADDR);
hcor = (struct ehci_hcor *)((uint32_t) hccr +
HC_LENGTH(ehci_readl(&hccr->cr_capbase)));
- usb_dev_init();
return 0;
}
* Memory Info
*/
#define CONFIG_SYS_MALLOC_LEN (0x10000 + 1*1024*1024) /* malloc() len */
-#define PHYS_SDRAM_1 DAVINCI_DDR_EMIF_DATA_BASE /* DDR Start */
-#define PHYS_SDRAM_1_SIZE (64 << 20) /* SDRAM size 64MB */
+#define PHYS_SDRAM_1 0xc0000000 /* SDRAM Start */
#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM_1 /* memtest start addr */
#define CONFIG_SYS_MEMTEST_END (PHYS_SDRAM_1 + 16*1024*1024) /* 16MB test */
#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */
#define CONFIG_SYS_ALE_MASK 0x8
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
#define NAND_MAX_CHIPS 1
-#define DEF_BOOTM ""
#endif
#ifdef CONFIG_USE_NOR
"mtdparts=davinci_nand.1:" PART_BOOT PART_PARAMS PART_KERNEL PART_REST
#endif
+#define CONFIG_MAX_RAM_BANK_SIZE (512 << 20) /* max size from SPRS586*/
+
+/* additions for new relocation code, must be added to all boards */
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE)
+
#endif /* __CONFIG_H */
#undef CONFIG_SYS_NAND_HW_ECC
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
#define NAND_MAX_CHIPS 1
-#define DEF_BOOTM ""
#endif
/*
*/
#define LINUX_BOOT_PARAM_ADDR (PHYS_SDRAM_1 + 0x100)
#define CONFIG_CMDLINE_TAG
+#define CONFIG_REVISION_TAG
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_BOOTARGS \
"mem=32M console=ttyS2,115200n8 root=/dev/mtdblock2 rw noinitrd ip=dhcp"
#define CONFIG_SYS_NAND_HW_ECC
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
#define CONFIG_ENV_OFFSET 0x0 /* Block 0--not used by bootcode */
-#define DEF_BOOTM ""
#elif defined(CONFIG_SYS_USE_NOR)
#ifdef CONFIG_NOR_UART_BOOT
#define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is loaded by a bootloader */
#define CONFIG_SYS_NAND_HW_ECC
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
#define CONFIG_ENV_OFFSET 0x0 /* Block 0--not used by bootcode */
-#define DEF_BOOTM ""
#elif defined(CONFIG_SYS_USE_NOR)
#ifdef CONFIG_NOR_UART_BOOT
#define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is loaded by a bootloader */
--- /dev/null
+/*
+ * Copyright (C) 2010 Eric C. Cooper <ecc@cmu.edu>
+ *
+ * Based on sheevaplug.h originally written by
+ * Prafulla Wadaskar <prafulla@marvell.com>
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef _CONFIG_DOCKSTAR_H
+#define _CONFIG_DOCKSTAR_H
+
+/*
+ * Version number information
+ */
+#define CONFIG_IDENT_STRING "\nSeagate FreeAgent DockStar"
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+#define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */
+#define CONFIG_KIRKWOOD 1 /* SOC Family Name */
+#define CONFIG_KW88F6281 1 /* SOC Name */
+#define CONFIG_MACH_DOCKSTAR /* Machine type */
+#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
+
+/*
+ * Commands configuration
+ */
+#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */
+#include <config_cmd_default.h>
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_USB
+/*
+ * mv-common.h should be defined after CMD configs since it used them
+ * to enable certain macros
+ */
+#include "mv-common.h"
+
+#undef CONFIG_SYS_PROMPT /* previously defined in mv-common.h */
+#define CONFIG_SYS_PROMPT "DockStar> " /* Command Prompt */
+
+/*
+ * Environment variables configurations
+ */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_ENV_IS_IN_NAND 1
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K */
+#else
+#define CONFIG_ENV_IS_NOWHERE 1 /* if env in SDRAM */
+#endif
+/*
+ * max 4k env size is enough, but in case of nand
+ * it has to be rounded to sector size
+ */
+#define CONFIG_ENV_SIZE 0x20000 /* 128k */
+#define CONFIG_ENV_ADDR 0x60000
+#define CONFIG_ENV_OFFSET 0x60000 /* env starts here */
+
+/*
+ * Default environment variables
+ */
+#define CONFIG_BOOTCOMMAND \
+ "setenv bootargs ${console} ${mtdparts} ${bootargs_root}; " \
+ "ubi part root; " \
+ "ubifsmount root; " \
+ "ubifsload 0x800000 ${kernel}; " \
+ "ubifsload 0x1100000 ${initrd}; " \
+ "bootm 0x800000 0x1100000"
+
+#define CONFIG_MTDPARTS "mtdparts=orion_nand:1m(uboot),-(root)\0"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "console=console=ttyS0,115200\0" \
+ "mtdids=nand0=orion_nand\0" \
+ "mtdparts="CONFIG_MTDPARTS \
+ "kernel=/boot/uImage\0" \
+ "initrd=/boot/uInitrd\0" \
+ "bootargs_root=ubi.mtd=1 root=ubi0:root rootfstype=ubifs ro\0"
+
+/*
+ * Ethernet Driver configuration
+ */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */
+#define CONFIG_PHY_BASE_ADR 0
+#endif /* CONFIG_CMD_NET */
+
+/*
+ * File system
+ */
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_UBI
+#define CONFIG_CMD_UBIFS
+#define CONFIG_RBTREE
+#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
+#define CONFIG_MTD_PARTITIONS
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_LZO
+
+#endif /* _CONFIG_DOCKSTAR_H */
#define PISMO1_NAND_SIZE GPMC_SIZE_128M
#define PISMO1_ONEN_SIZE GPMC_SIZE_128M
-#define CONFIG_SYS_MAX_FLASH_SECT 520 /* max number of sectors on */
- /* one chip */
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of flash banks */
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
#define CONFIG_SYS_FLASH_BASE boot_flash_base
#define CONFIG_ENV_OFFSET boot_flash_off
#define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
-/*-----------------------------------------------------------------------
- * CFI FLASH driver setup
- */
-/* timeout values are in ticks */
-#define CONFIG_SYS_FLASH_ERASE_TOUT (100 * CONFIG_SYS_HZ)
-#define CONFIG_SYS_FLASH_WRITE_TOUT (100 * CONFIG_SYS_HZ)
-
-/* Flash banks JFFS2 should use */
-#define CONFIG_SYS_MAX_MTD_BANKS (CONFIG_SYS_MAX_FLASH_BANKS + \
- CONFIG_SYS_MAX_NAND_DEVICE)
-#define CONFIG_SYS_JFFS2_MEM_NAND
-/* use flash_info[2] */
-#define CONFIG_SYS_JFFS2_FIRST_BANK CONFIG_SYS_MAX_FLASH_BANKS
-#define CONFIG_SYS_JFFS2_NUM_BANKS 1
-
#ifndef __ASSEMBLY__
extern unsigned int boot_flash_base;
extern volatile unsigned int boot_flash_env_addr;
#define PISMO1_NAND_SIZE GPMC_SIZE_128M
#define PISMO1_ONEN_SIZE GPMC_SIZE_128M
-#define CONFIG_SYS_MAX_FLASH_SECT 520 /* max number of sectors */
- /* on one chip */
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of flash banks */
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
#define CONFIG_SYS_FLASH_BASE boot_flash_base
#define CONFIG_ENV_OFFSET boot_flash_off
#define CONFIG_ENV_ADDR boot_flash_env_addr
-/*-----------------------------------------------------------------------
- * CFI FLASH driver setup
- */
-/* timeout values are in ticks */
-#define CONFIG_SYS_FLASH_ERASE_TOUT (100 * CONFIG_SYS_HZ)
-#define CONFIG_SYS_FLASH_WRITE_TOUT (100 * CONFIG_SYS_HZ)
-
-/* Flash banks JFFS2 should use */
-#define CONFIG_SYS_MAX_MTD_BANKS (CONFIG_SYS_MAX_FLASH_BANKS + \
- CONFIG_SYS_MAX_NAND_DEVICE)
-#define CONFIG_SYS_JFFS2_MEM_NAND
-/* use flash_info[2] */
-#define CONFIG_SYS_JFFS2_FIRST_BANK CONFIG_SYS_MAX_FLASH_BANKS
-#define CONFIG_SYS_JFFS2_NUM_BANKS 1
-
#ifndef __ASSEMBLY__
extern unsigned int boot_flash_base;
extern volatile unsigned int boot_flash_env_addr;
#define PISMO1_NAND_SIZE GPMC_SIZE_128M
#define PISMO1_ONEN_SIZE GPMC_SIZE_128M
-#define CONFIG_SYS_MAX_FLASH_SECT 520 /* max number of sectors on */
- /* one chip */
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of flash banks */
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
#define CONFIG_SYS_FLASH_BASE boot_flash_base
#define CONFIG_ENV_OFFSET boot_flash_off
#define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
-/*-----------------------------------------------------------------------
- * CFI FLASH driver setup
- */
-/* timeout values are in ticks */
-#define CONFIG_SYS_FLASH_ERASE_TOUT (100 * CONFIG_SYS_HZ)
-#define CONFIG_SYS_FLASH_WRITE_TOUT (100 * CONFIG_SYS_HZ)
-
-/* Flash banks JFFS2 should use */
-#define CONFIG_SYS_MAX_MTD_BANKS (CONFIG_SYS_MAX_FLASH_BANKS + \
- CONFIG_SYS_MAX_NAND_DEVICE)
-#define CONFIG_SYS_JFFS2_MEM_NAND
-/* use flash_info[2] */
-#define CONFIG_SYS_JFFS2_FIRST_BANK CONFIG_SYS_MAX_FLASH_BANKS
-#define CONFIG_SYS_JFFS2_NUM_BANKS 1
-
#ifndef __ASSEMBLY__
extern unsigned int boot_flash_base;
extern volatile unsigned int boot_flash_env_addr;
/*
- * (C) Copyright 2008
- * Grazvydas Ignotas <notasas@gmail.com>
+ * (C) Copyright 2008-2010
+ * GraΕΎvydas Ignotas <notasas@gmail.com>
*
* Configuration settings for the OMAP3 Pandora.
*
* Size of malloc() pool
*/
#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
- /* Sector */
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10))
- /* initial data */
+#define CONFIG_SYS_MALLOC_LEN (1024 * 1024 + CONFIG_ENV_SIZE)
/*
* Hardware drivers
*/
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1
+#define CONFIG_SYS_DEVICE_NULLDEV 1
+
+/* USB */
+#define CONFIG_MUSB_UDC 1
+#define CONFIG_USB_OMAP3 1
+#define CONFIG_TWL4030_USB 1
+
+/* USB device configuration */
+#define CONFIG_USB_DEVICE 1
+#define CONFIG_USB_TTY 1
+
/*
* NS16550 Configuration
*/
#define CONFIG_CMD_EXT2 /* EXT2 Support */
#define CONFIG_CMD_FAT /* FAT support */
-#define CONFIG_CMD_JFFS2 /* JFFS2 Support */
#define CONFIG_CMD_I2C /* I2C serial bus support */
#define CONFIG_CMD_MMC /* MMC support */
#define CONFIG_CMD_NAND /* NAND support */
+#define CONFIG_CMD_CACHE /* Cache control */
#undef CONFIG_CMD_FLASH /* flinfo, erase, protect */
#undef CONFIG_CMD_FPGA /* FPGA configuration Support */
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
/* devices */
-#define CONFIG_JFFS2_NAND
-/* nand device jffs2 lives on */
-#define CONFIG_JFFS2_DEV "nand0"
-/* start of jffs2 partition */
-#define CONFIG_JFFS2_PART_OFFSET 0x680000
-#define CONFIG_JFFS2_PART_SIZE 0xf980000 /* size of jffs2 */
- /* partition */
+
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_MTD_PARTITIONS
+#define CONFIG_MTD_DEVICE
+#define CONFIG_CMD_UBI
+#define CONFIG_CMD_UBIFS
+#define CONFIG_RBTREE
+#define CONFIG_LZO
+
+#define MTDIDS_DEFAULT "nand0=nand"
+#define MTDPARTS_DEFAULT "mtdparts=nand:512k(xloader),"\
+ "1920k(uboot),128k(uboot-env),"\
+ "10m(boot),-(rootfs)"
+#else
+#define MTDPARTS_DEFAULT
+#endif
/* Environment information */
#define CONFIG_BOOTDELAY 1
#define CONFIG_EXTRA_ENV_SETTINGS \
+ "usbtty=cdc_acm\0" \
"loadaddr=0x82000000\0" \
- "console=ttyS0,115200n8\0" \
- "videospec=omapfb:vram:2M,vram:4M\0" \
- "mmcargs=setenv bootargs console=${console} " \
- "video=${videospec} " \
- "root=/dev/mmcblk0p2 rw " \
- "rootfstype=ext3 rootwait\0" \
- "nandargs=setenv bootargs console=${console} " \
- "video=${videospec} " \
- "root=/dev/mtdblock4 rw " \
- "rootfstype=jffs2\0" \
- "loadbootscript=fatload mmc 0 ${loadaddr} boot.scr\0" \
- "bootscript=echo Running bootscript from mmc ...; " \
- "source ${loadaddr}\0" \
- "loaduimage=fatload mmc 0 ${loadaddr} uImage\0" \
- "mmcboot=echo Booting from mmc ...; " \
- "run mmcargs; " \
- "bootm ${loadaddr}\0" \
- "nandboot=echo Booting from nand ...; " \
- "run nandargs; " \
- "nand read ${loadaddr} 280000 400000; " \
- "bootm ${loadaddr}\0" \
+ "bootargs=ubi.mtd=4 ubi.mtd=3 root=ubi0:rootfs rootfstype=ubifs " \
+ "rw rootflags=bulk_read console=ttyS0,115200n8 " \
+ "vram=6272K omapfb.vram=0:3000K\0" \
+ "mtdparts=" MTDPARTS_DEFAULT "\0" \
#define CONFIG_BOOTCOMMAND \
- "if mmc init; then " \
- "if run loadbootscript; then " \
- "run bootscript; " \
- "else " \
- "if run loaduimage; then " \
- "run mmcboot; " \
- "else run nandboot; " \
- "fi; " \
- "fi; " \
- "else run nandboot; fi"
+ "if mmc init && fatload mmc1 0 ${loadaddr} autoboot.scr || " \
+ "ext2load mmc1 0 ${loadaddr} autoboot.scr; then " \
+ "source ${loadaddr}; " \
+ "fi; " \
+ "ubi part boot && ubifsmount boot && ubifsload ${loadaddr} uImage && bootm ${loadaddr}"
#define CONFIG_AUTO_COMPLETE 1
/*
/* SDRAM Bank Allocation method */
#define SDRC_R_B_C 1
+#define CONFIG_SYS_TEXT_BASE 0x80008000
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
+#define CONFIG_SYS_INIT_RAM_SIZE 0x800
+#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
+ CONFIG_SYS_INIT_RAM_SIZE - \
+ GENERATED_GBL_DATA_SIZE)
+
/*-----------------------------------------------------------------------
* FLASH and environment organization
*/
#define PISMO1_NAND_SIZE GPMC_SIZE_128M
#define PISMO1_ONEN_SIZE GPMC_SIZE_128M
-#define CONFIG_SYS_MAX_FLASH_SECT 520 /* max number of sectors on */
- /* one chip */
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of flash banks */
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
#define CONFIG_SYS_FLASH_BASE boot_flash_base
/* Monitor at start of flash */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_ONENAND_BASE ONENAND_MAP
#define CONFIG_ENV_IS_IN_NAND 1
-#define ONENAND_ENV_OFFSET 0x240000 /* environment starts here */
-#define SMNAND_ENV_OFFSET 0x240000 /* environment starts here */
+#define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */
#define CONFIG_SYS_ENV_SECT_SIZE boot_flash_sec
#define CONFIG_ENV_OFFSET boot_flash_off
#define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
-/*-----------------------------------------------------------------------
- * CFI FLASH driver setup
- */
-/* timeout values are in ticks */
-#define CONFIG_SYS_FLASH_ERASE_TOUT (100 * CONFIG_SYS_HZ)
-#define CONFIG_SYS_FLASH_WRITE_TOUT (100 * CONFIG_SYS_HZ)
-
-/* Flash banks JFFS2 should use */
-#define CONFIG_SYS_MAX_MTD_BANKS (CONFIG_SYS_MAX_FLASH_BANKS + \
- CONFIG_SYS_MAX_NAND_DEVICE)
-#define CONFIG_SYS_JFFS2_MEM_NAND
-/* use flash_info[2] */
-#define CONFIG_SYS_JFFS2_FIRST_BANK CONFIG_SYS_MAX_FLASH_BANKS
-#define CONFIG_SYS_JFFS2_NUM_BANKS 1
-
#ifndef __ASSEMBLY__
extern unsigned int boot_flash_base;
extern volatile unsigned int boot_flash_env_addr;
#define PHYS_FLASH_SIZE (128 << 20)
#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max sectors on one chip */
-/* timeout values are in milliseconds */
-#define CONFIG_SYS_FLASH_ERASE_TOUT (100 * CONFIG_SYS_HZ)
-#define CONFIG_SYS_FLASH_WRITE_TOUT (100 * CONFIG_SYS_HZ)
-
/* OMITTED: single 2 Gbit KFM2G16 OneNAND flash */
#define CONFIG_ENV_IS_IN_FLASH 1
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_MONITOR_LEN (256 << 10)
-#define CONFIG_SYS_JFFS2_FIRST_BANK CONFIG_SYS_MAX_FLASH_BANKS
-#define CONFIG_SYS_JFFS2_NUM_BANKS 1
-
/*
* NAND FLASH usage ... default nCS1:
* - four 128KB sectors for X-Loader
#define PISMO1_NAND_SIZE GPMC_SIZE_128M
#define PISMO1_ONEN_SIZE GPMC_SIZE_128M
-#define CONFIG_SYS_MAX_FLASH_SECT 520 /* max number of sectors on */
- /* one chip */
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of flash banks */
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
#define CONFIG_SYS_FLASH_BASE boot_flash_base
#define CONFIG_ENV_OFFSET boot_flash_off
#define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
-/*-----------------------------------------------------------------------
- * CFI FLASH driver setup
- */
-/* timeout values are in ticks */
-#define CONFIG_SYS_FLASH_ERASE_TOUT (100 * CONFIG_SYS_HZ)
-#define CONFIG_SYS_FLASH_WRITE_TOUT (100 * CONFIG_SYS_HZ)
-
-/* Flash banks JFFS2 should use */
-#define CONFIG_SYS_MAX_MTD_BANKS (CONFIG_SYS_MAX_FLASH_BANKS + \
- CONFIG_SYS_MAX_NAND_DEVICE)
-#define CONFIG_SYS_JFFS2_MEM_NAND
-/* use flash_info[2] */
-#define CONFIG_SYS_JFFS2_FIRST_BANK CONFIG_SYS_MAX_FLASH_BANKS
-#define CONFIG_SYS_JFFS2_NUM_BANKS 1
-
#ifndef __ASSEMBLY__
extern unsigned int boot_flash_base;
extern volatile unsigned int boot_flash_env_addr;
#define PISMO1_NAND_SIZE GPMC_SIZE_128M
#define PISMO1_ONEN_SIZE GPMC_SIZE_128M
-#define CONFIG_SYS_MAX_FLASH_SECT 520 /* max number of sectors on */
- /* one chip */
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of flash banks */
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
#define CONFIG_SYS_FLASH_BASE boot_flash_base
#define CONFIG_ENV_OFFSET boot_flash_off
#define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
-/*-----------------------------------------------------------------------
- * CFI FLASH driver setup
- */
-/* timeout values are in ticks */
-#define CONFIG_SYS_FLASH_ERASE_TOUT (100 * CONFIG_SYS_HZ)
-#define CONFIG_SYS_FLASH_WRITE_TOUT (100 * CONFIG_SYS_HZ)
-
#ifndef __ASSEMBLY__
extern unsigned int boot_flash_base;
extern volatile unsigned int boot_flash_env_addr;
/* Disabled commands */
#undef CONFIG_CMD_NET
+#undef CONFIG_CMD_NFS
#undef CONFIG_CMD_FPGA /* FPGA configuration Support */
#undef CONFIG_CMD_IMLS /* List all found images */
#define CONFIG_JFFS2_NAND
#define NAND_MAX_CHIPS 1
#define CONFIG_ENV_OFFSET 0x180000
-#define DEF_BOOTM ""
/*
* davinci_nand is a bit of a misnomer since this particular EMIF block is
projects / karo-tx-uboot.git / commitdiff