Robby Cai [Thu, 22 Aug 2013 10:01:59 +0000 (18:01 +0800)]
ENGR00275033-1 mx6sl: pxp/v4l: port v4l2 output driver to 3.10
port v4l2 output driver to 3.10 kernel
- replace .ioctl with .unlocked_ioctl
- add .vfl_dir flag - VFL_DIR_TX (newly introduced) for video_device
- drop __devinit, __devexit, __exit and __exit_p
- replace mxc_elcdif_frame_addr_setup() with pxp_show_buf(), where pan_display
be called due to the adoption of mxsfb.c from community
- change the fb id to be compared due to use new mxsfb.c
- mark the s_crop() and s_fbuf() third parameter const
- move local fbi variable to struct pxps
- use module_platform_driver()
Peter Chen [Wed, 10 Jul 2013 09:21:23 +0000 (17:21 +0800)]
ENGR00277805-2 usb: chipidea: udc: Consolidate the call of disconnect
The udc-core will call gadget's driver->disconnect, so we should avoid
calling gadget's disconnect again at ci_udc_stop in case the gadget's
unbind free some structs which is still used at gadget's disconnect.
Tested-by: Marek Vasut <marex@denx.de> Signed-off-by: Peter Chen <peter.chen@freescale.com>
Nicolin Chen [Thu, 29 Aug 2013 06:27:32 +0000 (14:27 +0800)]
ENGR00276567-5 mfd: si476x: Add two involatile registers support
These two regsiters would be used by si476x-codec driver. Setting them as
involatile registers would allow codec driver to set the value into cache
and to sync them after power-up.
The commit fc52e42 (ENGR00269945: ARM: imx6: remove sabresd hdcp dts
files) removes dts but leaves dtb targets in Makefile. This causes
build issue with 'make ARCH=arm dtbs'. Remove the dead targets.
Liu Ying [Wed, 28 Aug 2013 03:07:52 +0000 (11:07 +0800)]
ENGR00277003 IPUv3: Update IC RGB2YUV CSC matrix parameters
This patch updates IPUv3 IC RGB to YUV color space conversion
matrix's parameters to align with the default VIV GPU CSC
implementation so that we may pass relevant Android CTS test
cases.
Shawn Guo [Wed, 28 Aug 2013 08:03:53 +0000 (16:03 +0800)]
ENGR00269945: ARM: imx: add an ARMv7 only defconfig
To utilize ARMv7 optimization, let's maintain an ARMv7 only defconfig
imx_v7_defconfig. It's generated as below.
* make ARCH=arm imx_v6_v7_defconfig
* make ARCH=arm menuconfig
* System Type ---> Multiple platform selection ---> Deselect ARMv6
based platforms (ARM11)
* make ARCH=arm savedefconfig
* cp defconfig arch/arm/configs/imx_v7_defconfig
Shawn Guo [Tue, 27 Aug 2013 03:47:29 +0000 (11:47 +0800)]
ENGR00269945: ARM: imx6: maintain pinctrl setting outside bus topology
The patch moves all pinctrl setting nodes outside bus topology using
label, so that we can reduce some indent levels for these nodes and
avoid churning main device nodes structure chunk.
While at it, the patch also sorts those pinctrl setting nodes
alphabetically.
Since U-Boot provide good support for modify device tree blob (DTB) at
run-time with 'fdt' command, we do not have to maintain extra DTS files
just for pin conflict case.
Robby Cai [Thu, 22 Aug 2013 06:39:42 +0000 (14:39 +0800)]
ENGR00275031-2 ARM: dts: add lcdif and backlight support
Add dts for lcdif, backlight(pwm).
- use display timing dts bindings for lcd timing setting.
- add an axi clock node for mx23/mx28 to accommadate the change in driver
Robby Cai [Thu, 22 Aug 2013 06:35:09 +0000 (14:35 +0800)]
ENGR00275031-1 mx6sl fb: support lcdif framebuffer on 3.10
re-use the upstreaming mxsfb.c code.
- add the lcdif axi clock for register and dram access
- set the lcdif pix's parent as pll5_video to get most accurate pix clock
- add binding doc for lcdif dts
Luwei Zhou [Wed, 21 Aug 2013 08:53:32 +0000 (16:53 +0800)]
ENGR00275983 sensor: Add mma8451 sensor driver
Add mxa-mma8451.c to support mma8451 sensor. Copy
the file from 3.0.35_4.1.0. Modificaiton List:
1.Remove __devinit,__devexit out of code
2.Support device tree.
3.Replace simple_strtoul with strict_strtoul.
Hongzhang Yang [Fri, 16 Aug 2013 02:33:41 +0000 (10:33 +0800)]
ENGR00275473-2 Support PU regulator on/off in VPU driver
Add functions to hide different implemention for different
kernel
- vpu_power_get: get/put power/regulator
- vpu_power_up: enable/disable power/regulator
- vpu_reset
Implement regulator operations for Linux 3.10
- find regulator from VPU device node property
pu-supply
Replace printk/pr_xxx with dev_xxx
Signed-off-by: Hongzhang Yang <Hongzhang.Yang@freescale.com>
ENGR00258733 WEIM-NOR: mtd: cfi_cmdset_0002: Do not release the mutex lock
The NOR(M29W256GL7AN6E) may suffers a write-buffer timeout during
the bonnie++/ubifs stress test. Micron has confirmed that it is
a silicon bug in the Nor.
This patch is just a workaround to fix this issue for this NOR.
With this patch, the read/write/erase will do in the synchronous way.
ENGR00257947 mtd: use memcpy to replace the memcpy_fromio
During the read of NOR, the kernel actually calls the inline_map_copy_from()
to read the data out. And inline_map_copy_from() will use the memcpy_fromio()
to do the real job.
The memcpy_fromio macro maps _memcpy_fromio() in the current code.
But the _memcpy_fromio() will use readb() to do the copy work one byte
by one byte. This makes the read performance of NOR very slow(about 2~3MB/s).
A similiar discussion could be found in:
http://lists.infradead.org/pipermail/linux-arm-kernel/2009-November/003860.html
This patch replace the memcpy_fromio with memcpy which is optimized by the
kernel.
The following is the result from mtd_speedtest with M29W256GL7AN6E:
=================================================
mtd_speedtest: MTD device: 2
mtd_speedtest: not NAND flash, assume page size is 512 bytes.
mtd_speedtest: MTD device size 4194304, eraseblock size 131072, page size 512,
count of eraseblocks 32, pages per eraseblock 256, OOB size 0
mtd_speedtest: testing eraseblock write speed
mtd_speedtest: eraseblock write speed is 845 KiB/s
mtd_speedtest: testing eraseblock read speed
mtd_speedtest: eraseblock read speed is 19504 KiB/s
mtd_speedtest: testing page write speed
mtd_speedtest: page write speed is 845 KiB/s
mtd_speedtest: testing page read speed
mtd_speedtest: page read speed is 19140 KiB/s
mtd_speedtest: testing 2 page write speed
mtd_speedtest: 2 page write speed is 846 KiB/s
mtd_speedtest: testing 2 page read speed
mtd_speedtest: 2 page read speed is 19320 KiB/s
mtd_speedtest: Testing erase speed
mtd_speedtest: erase speed is 233 KiB/s
mtd_speedtest: Testing 2x multi-block erase speed
mtd_speedtest: 2x multi-block erase speed is 225 KiB/s
mtd_speedtest: Testing 4x multi-block erase speed
mtd_speedtest: 4x multi-block erase speed is 224 KiB/s
mtd_speedtest: Testing 8x multi-block erase speed
mtd_speedtest: 8x multi-block erase speed is 225 KiB/s
mtd_speedtest: Testing 16x multi-block erase speed
mtd_speedtest: 16x multi-block erase speed is 225 KiB/s
mtd_speedtest: Testing 32x multi-block erase speed
mtd_speedtest: 32x multi-block erase speed is 225 KiB/s
mtd_speedtest: Testing 64x multi-block erase speed
mtd_speedtest: 64x multi-block erase speed is 224 KiB/s
mtd_speedtest: finished
=================================================
Fugang Duan [Mon, 19 Aug 2013 02:58:24 +0000 (10:58 +0800)]
ENGR00275619 net: fec: set reset phy gpio to high in .probe().
In .probe() call fec_of_init() to parse phy reset gpio, and
request the gpio for later use. For the init, we must set the
gpio to high to let phy power on.
Connecting two boards directly more than 2 hours, Ar8031 phy link
status generates glitch, which cause ethernet link down/up issue, but
ethernet still be active. There have three cases to validate the issue:
Item#1: If add performance stress test while runing IEEE1588, the link
down/up issue cannot be found.
Item#2: If insert switch between two net nodes and run IEEE1588 test,
the issue also cannot be found.
Item#3: If disable AR8031 SmartEEE feature, after two days overnight test,
no such issue found.
The issue is caused by phy Ar8031 SmartEEE feature, Item#1 and Item#2 can
prevent phy enter lpm mode, which match the Item#3 test result, so disable
SmartEEE feature to avoid the link issue generation.
Current driver only do phy reset in probe function, which is
not right. Since some phy clock is disabled after module probe,
the phy enter abnormal status, which needs do reset to recovery
the phy. And do ifconfig ethx up/down test, the phy also enter
abnormal status.
The log as:
libphy: 2188000.ethernet:04 - Link is Up - 10/Full
libphy: 2188000.ethernet:04 - Link is Up - 100/Full
libphy: 2188000.ethernet:04 - Link is Down
libphy: 2188000.ethernet:04 - Link is Up - 10/Half
libphy: 2188000.ethernet:04 - Link is Up - 10/Full
libphy: 2188000.ethernet:04 - Link is Up - 100/Full
...
So, do phy reset if ethx up/down or do clock enable/disable
operation.
Shengjiu Wang [Fri, 9 Aug 2013 06:45:51 +0000 (14:45 +0800)]
ENGR00274585-9 ASoC: change error message to debug message
This error message is not actual error, which is a warning. When using
FE/BE, if there is widget which is used by playback and capture route, then
this message will be printed.
Signed-off-by: Shengjiu Wang <b02247@freescale.com>
Robby Cai [Thu, 8 Aug 2013 03:23:54 +0000 (11:23 +0800)]
ENGR00274412-1 dma: pxp: Port ePxP driver to 3.10
It's ported from v3.5.7, which contains ePxP DMAENGINE driver and
a client driver named pxp_device. This patch also includes the changes:
- use uapi header file
- remove VM_RESERVED since it's deprecated, and drop redundant VM_IO flag
since it's automatically set in remap_pfn_range()
- use <linux/platform_data/dma-imx.h> instead of <mach/dma.h>
- use devm_kzalloc() instead in pxp_probe()
- use macro __KERNEL__ in pxp_dma uapi header to avoid definition conflict
Sandor Yu [Tue, 13 Aug 2013 08:55:20 +0000 (16:55 +0800)]
ENGR00274059-02 ARM: Add new dts for imx6q/imx6dl SabreSD hdcp
hdcp ddc pins conflict with i2c2,
add new dts file for imx6q and imx6dl SabreSD board,
enable hdcp and disable i2c2 in these dts files.
Remove hdmi pins property from mx6qdl-sabresd.dtsi.
Anson Huang [Thu, 8 Aug 2013 21:05:38 +0000 (17:05 -0400)]
ENGR00274473-1 regulator: add more notifier events
Some hardware modules need strict flows according
to regulator's enable/disable, such as for i.MX6
SOC's PU regulator, there is another power gate
in GPC module, it needs to disable PU modules' clock
before PU regulator is disabled and need to enable
clock right after PU regulator is enabled, then it
can do GPC's power gate operation.
So we need to add REGULATOR_EVENT_PRE_DISABLE and
REGULATOR_EVENT_ENABLE for regulator's notifier events.
Hongzhang Yang [Mon, 12 Aug 2013 07:38:07 +0000 (15:38 +0800)]
ENGR00274761-3 Upgrade VPU driver for Linux 3.10 kernel
Modify mxc_vpu.c to adapt to kernel 3.10 change
- Remove all references to header files in mach folder
- Include linux/clk.h instead of mach/clock.h
- Call device_reset instead of imx_src_reset_vpu
- Dummy PU and PM api callings before they are ready
- Dummy cpu_is_mx5? api callings
- Remove VM_RESERVED flags
- Call gen_pool instead of iram_alloc
Modify mxc_vpu.h
- Change CONFIG_ARCH_MX6 to CONFIG_SOC_IMX6Q
Modify Kconfig:
- Change ARCH_MX? to SOC_IMX?, remove ARCH_MX3/ARCH_MX37
because for MX3 series only SOC_IMX31 and SOC_IMX35 are
defined in Linux 3.10, and these chips don't have VPU.
Need to add SOC_IMX37 to VPU Kconfig if MX37 could be
supported later.
Add VPU to config and build path
- mxc/Kconfig
- mxc/Makefile
Signed-off-by: Hongzhang Yang <Hongzhang.Yang@freescale.com>
Hongzhang Yang [Mon, 12 Aug 2013 07:23:41 +0000 (15:23 +0800)]
ENGR00274761-2 Upgrade VPU driver for Linux 3.10 kernel
Add VPU node in dtsi
- Add VPU node (common part) in imx6qdl.dtsi. It was defined
in imx6.dtsi in Linux 3.5.7.
- Add "iram" property for gen_pool api callings
- Add "resets" property for device_reset api calling
- Add VPU node (soc specific part) in imx6q.dtsi and imx6dl.dtsi
Signed-off-by: Hongzhang Yang <Hongzhang.Yang@freescale.com>
Hongzhang Yang [Mon, 12 Aug 2013 07:14:23 +0000 (15:14 +0800)]
ENGR00274761-1 Upgrade VPU driver for Linux 3.10 kernel
Pick files from origin/imx_3.5.7 commit 135bf02a0727ea5ce96
- mxc_vpu.h is picked from arch/arm/plat-mxc/include/mach/
and put to include/linux/
- drivers/mxc/vpu/Kconfig
- drivers/mxc/vpu/Makefile
- drivers/mxc/vpu/mxc_vpu.c
Signed-off-by: Hongzhang Yang <Hongzhang.Yang@freescale.com>
Sandor Yu [Mon, 12 Aug 2013 10:51:52 +0000 (18:51 +0800)]
ENGR00274821 ARM: Add i.MX6 FB properties to dts for SabreAuto board
- Add Framebuffer and ldb properties to dts for i.MX6Q and
i.MX6DL SabreAuto board.
- Add PWM3 and backlight properties to dts for i.MX6Q and
i.Mx6DL SabreAuto board.
- fix i2c2 indent in dts.
Luwei [Thu, 8 Aug 2013 08:35:24 +0000 (16:35 +0800)]
ENGR00274247: touch: add egalax touch driver support on i.MX6Q/DL AUTO/SD
Copy the egalax touch screen driver from linux3.5.7.Make some
modification.Remove the __devinit __devexit __devexit_p out
of the file, because 3.10 does not support.
This patch removes the unnecessary gpio_set_value() and
gpio_free() function calls after request the gpios with
gpio_requestion_one() successfully. Also, this patch adds
a warning message if the request fails.
Hannstar LVDS panel CABC function turns backlight density
automatically according to display content. This may introduce
annoying unstable backlight when display content changes.
So, this patch disables the CABC function if a platform's of
device tree provides controlling gpios in lvds_cabc_ctrl node.
This patch adds lvds_cabc_ctrl node in imx6qdl-sabresd.dtsi file.
This node contains two gpio entries for the Hannstar LVDS panel
CABC control function on LVDS0 and LVDS1 interfaces.
This patch adds pinmux entries for LVDS0 and LVDS1 to control the
Hannstar LVDS panel CABC function. Pin NANDF_CS2 and pin NANDF_CS3
are configured to be gpio so that they can control the CABC function.
Anson Huang [Thu, 8 Aug 2013 17:57:23 +0000 (13:57 -0400)]
ENGR00274056-3 thermal: imx: binding device cooling to thermal
1. imx thermal depends on device cooling config, as only cpu
cooling is not enough for cooling down SOC;
2. binding device cooling to imx thermal driver.
3. add temperature buffer for passive trip, which means when
temperature cross passive trip, cooling devices will be triggered,
but only when temperature drop to more than the number we defined(10 C)
lower than passive trip, cooling devices will be canceled. this
is to avoid triggering/canceling cooling device back and forth when
temperature is around passive trip.
Anson Huang [Thu, 8 Aug 2013 17:20:40 +0000 (13:20 -0400)]
ENGR00274056-1 thermal: add device cooling for thermal driver
cpu cooling is not enough when temperature is
too hot, as some devices may contribute a lot of heat
to SOC, such as GPU, so we need to add device cooling
as well, when system is too hot, devices can also take
their actions to lower SOC temperature.
when temperature cross the passive trip, device cooling
driver will send out notification, those devices who
register this devfreq_cooling notification will take
actions to lower SOC temperature.
Robin Gong [Mon, 5 Aug 2013 09:40:02 +0000 (17:40 +0800)]
ENGR00273425 ARM: imx: enable suspend code for imx6q/dl
Enable DSM code for imx6, the code porting form kernel 3.5.7.So with the patch,
we can suspend imx6q, imx6dl from iram to decrease power number of DDR IO:
save ~15mA@1.5V on imx6qsabresd, but need more ~30us in suspend and resume back.
Liu Ying [Mon, 5 Aug 2013 07:47:22 +0000 (15:47 +0800)]
ENGR00273974-1 media: port mxc vout driver from 3.5.7 to 3.10
This is porting mxc vout driver from imx_3.5.7 kernel to
imx_3.10 kernel.
* Put the driver in drivers/media/platform/ directory instead
of drivers/media/video/ directory, since the later one is
renamed to the former one in 3.10 kernel.
* Change the ipu-v3.h header file from <mach/ipu-v3.h> to
<linux/ipu-v3.h>.
* Change the mxc_vidioc_s_crop() function's implementation since
the definition of the vidioc_s_crop() function is modified to
make the last argument be constant.
* Set vfl_dir to be VFL_DIR_TX since the ioctrl validity checks
are improved in 3.10 kernel.
* Remove 'defaut y' setting for VIDEO_MXC_OUTPUT and
VIDEO_MXC_IPU_OUTPUT Kconfigs. They may be configured by kernel
default configure or by user.
* Make VIDEO_MXC_OUTPUT Kconfig depend on FB_MXC Kconfig since
we need framebuffers to be rendered.
* Make VIDEO_MXC_IPU_OUTPUT Kconfig be tristate.
* Split <linux/mxc_v4l2.h> header file up into include/linux/
and include/uapi/linux/ directories so that the userspace may
include the mxc_v4l2.h header file.
Liu Ying [Mon, 5 Aug 2013 07:33:49 +0000 (15:33 +0800)]
ENGR00273852 ipu: header file split up
This patch splits ipu header file up to
include/linux/ directory and include/uapi/linux/
directory so that the userspace may include
the ipu header file. This patch also fixes some
annotations and macros about the header file's
naming.
Liu Ying [Thu, 1 Aug 2013 08:32:11 +0000 (16:32 +0800)]
ENGR00273500 IPUv3 dev: use wait_event_interruptible for ipu task
The ipu task thread checks outstanding tasks to be done on waiting
event uninterruptibly on the function find_task()'s return value.
However, sleeping on waiting event uninterruptibly contributes to
system load average value. This patch changes wait_event() to
wait_event_interruptible() to avoid the load average value inflation.
Fabio Estevam [Sun, 9 Jun 2013 18:17:18 +0000 (15:17 -0300)]
serial: imx: Fix serial clock unbalance
Since commit 0c375501 (serial: imx: enable the clocks for console), the
imx_startup() function calls clk_prepare_enable conditionally, so we
need to call clk_disable_unprepare inside imx_shutdown() under the same
condition to avoid unbalanced clock calls.
ENGR00240988: ARM: imx6q: add dma_zone_size for GPU limit
GPU has a limit on physical address that it accesses, which must be
below 2GiB. Since i.MX6Q/DL maps system memory at 0x10000000 (offset
256MiB), we set dma_zone_size as (SZ_2G - SZ_256M) to ensure that.
projects / karo-tx-linux.git / log