2 # (C) Copyright 2000 - 2008
3 # Wolfgang Denk, DENX Software Engineering, wd@denx.de.
5 # See file CREDITS for list of people who contributed to this
8 # This program is free software; you can redistribute it and/or
9 # modify it under the terms of the GNU General Public License as
10 # published by the Free Software Foundation; either version 2 of
11 # the License, or (at your option) any later version.
13 # This program is distributed in the hope that it will be useful,
14 # but WITHOUT ANY WARRANTY; without even the implied warranty of
15 # MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
16 # GNU General Public License for more details.
18 # You should have received a copy of the GNU General Public License
19 # along with this program; if not, write to the Free Software
20 # Foundation, Inc., 59 Temple Place, Suite 330, Boston,
27 This directory contains the source code for U-Boot, a boot loader for
28 Embedded boards based on PowerPC, ARM, MIPS and several other
29 processors, which can be installed in a boot ROM and used to
30 initialize and test the hardware or to download and run application
33 The development of U-Boot is closely related to Linux: some parts of
34 the source code originate in the Linux source tree, we have some
35 header files in common, and special provision has been made to
36 support booting of Linux images.
38 Some attention has been paid to make this software easily
39 configurable and extendable. For instance, all monitor commands are
40 implemented with the same call interface, so that it's very easy to
41 add new commands. Also, instead of permanently adding rarely used
42 code (for instance hardware test utilities) to the monitor, you can
43 load and run it dynamically.
49 In general, all boards for which a configuration option exists in the
50 Makefile have been tested to some extent and can be considered
51 "working". In fact, many of them are used in production systems.
53 In case of problems see the CHANGELOG and CREDITS files to find out
54 who contributed the specific port. The MAINTAINERS file lists board
61 In case you have questions about, problems with or contributions for
62 U-Boot you should send a message to the U-Boot mailing list at
63 <u-boot@lists.denx.de>. There is also an archive of previous traffic
64 on the mailing list - please search the archive before asking FAQ's.
65 Please see http://lists.denx.de/pipermail/u-boot and
66 http://dir.gmane.org/gmane.comp.boot-loaders.u-boot
69 Where to get source code:
70 =========================
72 The U-Boot source code is maintained in the git repository at
73 git://www.denx.de/git/u-boot.git ; you can browse it online at
74 http://www.denx.de/cgi-bin/gitweb.cgi?p=u-boot.git;a=summary
76 The "snapshot" links on this page allow you to download tarballs of
77 any version you might be interested in. Official releases are also
78 available for FTP download from the ftp://ftp.denx.de/pub/u-boot/
81 Pre-built (and tested) images are available from
82 ftp://ftp.denx.de/pub/u-boot/images/
88 - start from 8xxrom sources
89 - create PPCBoot project (http://sourceforge.net/projects/ppcboot)
91 - make it easier to add custom boards
92 - make it possible to add other [PowerPC] CPUs
93 - extend functions, especially:
94 * Provide extended interface to Linux boot loader
97 * PCMCIA / CompactFlash / ATA disk / SCSI ... boot
98 - create ARMBoot project (http://sourceforge.net/projects/armboot)
99 - add other CPU families (starting with ARM)
100 - create U-Boot project (http://sourceforge.net/projects/u-boot)
101 - current project page: see http://www.denx.de/wiki/U-Boot
107 The "official" name of this project is "Das U-Boot". The spelling
108 "U-Boot" shall be used in all written text (documentation, comments
109 in source files etc.). Example:
111 This is the README file for the U-Boot project.
113 File names etc. shall be based on the string "u-boot". Examples:
115 include/asm-ppc/u-boot.h
117 #include <asm/u-boot.h>
119 Variable names, preprocessor constants etc. shall be either based on
120 the string "u_boot" or on "U_BOOT". Example:
122 U_BOOT_VERSION u_boot_logo
123 IH_OS_U_BOOT u_boot_hush_start
129 U-Boot uses a 3 level version number containing a version, a
130 sub-version, and a patchlevel: "U-Boot-2.34.5" means version "2",
131 sub-version "34", and patchlevel "4".
133 The patchlevel is used to indicate certain stages of development
134 between released versions, i. e. officially released versions of
135 U-Boot will always have a patchlevel of "0".
141 - board Board dependent files
142 - common Misc architecture independent functions
143 - cpu CPU specific files
144 - 74xx_7xx Files specific to Freescale MPC74xx and 7xx CPUs
145 - arm720t Files specific to ARM 720 CPUs
146 - arm920t Files specific to ARM 920 CPUs
147 - at91rm9200 Files specific to Atmel AT91RM9200 CPU
148 - imx Files specific to Freescale MC9328 i.MX CPUs
149 - s3c24x0 Files specific to Samsung S3C24X0 CPUs
150 - arm925t Files specific to ARM 925 CPUs
151 - arm926ejs Files specific to ARM 926 CPUs
152 - arm1136 Files specific to ARM 1136 CPUs
153 - at32ap Files specific to Atmel AVR32 AP CPUs
154 - blackfin Files specific to Analog Devices Blackfin CPUs
155 - i386 Files specific to i386 CPUs
156 - ixp Files specific to Intel XScale IXP CPUs
157 - leon2 Files specific to Gaisler LEON2 SPARC CPU
158 - leon3 Files specific to Gaisler LEON3 SPARC CPU
159 - mcf52x2 Files specific to Freescale ColdFire MCF52x2 CPUs
160 - mcf5227x Files specific to Freescale ColdFire MCF5227x CPUs
161 - mcf532x Files specific to Freescale ColdFire MCF5329 CPUs
162 - mcf5445x Files specific to Freescale ColdFire MCF5445x CPUs
163 - mcf547x_8x Files specific to Freescale ColdFire MCF547x_8x CPUs
164 - mips Files specific to MIPS CPUs
165 - mpc5xx Files specific to Freescale MPC5xx CPUs
166 - mpc5xxx Files specific to Freescale MPC5xxx CPUs
167 - mpc8xx Files specific to Freescale MPC8xx CPUs
168 - mpc8220 Files specific to Freescale MPC8220 CPUs
169 - mpc824x Files specific to Freescale MPC824x CPUs
170 - mpc8260 Files specific to Freescale MPC8260 CPUs
171 - mpc85xx Files specific to Freescale MPC85xx CPUs
172 - nios Files specific to Altera NIOS CPUs
173 - nios2 Files specific to Altera Nios-II CPUs
174 - ppc4xx Files specific to AMCC PowerPC 4xx CPUs
175 - pxa Files specific to Intel XScale PXA CPUs
176 - s3c44b0 Files specific to Samsung S3C44B0 CPUs
177 - sa1100 Files specific to Intel StrongARM SA1100 CPUs
178 - disk Code for disk drive partition handling
179 - doc Documentation (don't expect too much)
180 - drivers Commonly used device drivers
181 - dtt Digital Thermometer and Thermostat drivers
182 - examples Example code for standalone applications, etc.
183 - include Header Files
184 - lib_arm Files generic to ARM architecture
185 - lib_avr32 Files generic to AVR32 architecture
186 - lib_blackfin Files generic to Blackfin architecture
187 - lib_generic Files generic to all architectures
188 - lib_i386 Files generic to i386 architecture
189 - lib_m68k Files generic to m68k architecture
190 - lib_mips Files generic to MIPS architecture
191 - lib_nios Files generic to NIOS architecture
192 - lib_ppc Files generic to PowerPC architecture
193 - lib_sparc Files generic to SPARC architecture
194 - libfdt Library files to support flattened device trees
195 - net Networking code
196 - post Power On Self Test
197 - rtc Real Time Clock drivers
198 - tools Tools to build S-Record or U-Boot images, etc.
200 Software Configuration:
201 =======================
203 Configuration is usually done using C preprocessor defines; the
204 rationale behind that is to avoid dead code whenever possible.
206 There are two classes of configuration variables:
208 * Configuration _OPTIONS_:
209 These are selectable by the user and have names beginning with
212 * Configuration _SETTINGS_:
213 These depend on the hardware etc. and should not be meddled with if
214 you don't know what you're doing; they have names beginning with
217 Later we will add a configuration tool - probably similar to or even
218 identical to what's used for the Linux kernel. Right now, we have to
219 do the configuration by hand, which means creating some symbolic
220 links and editing some configuration files. We use the TQM8xxL boards
224 Selection of Processor Architecture and Board Type:
225 ---------------------------------------------------
227 For all supported boards there are ready-to-use default
228 configurations available; just type "make <board_name>_config".
230 Example: For a TQM823L module type:
235 For the Cogent platform, you need to specify the CPU type as well;
236 e.g. "make cogent_mpc8xx_config". And also configure the cogent
237 directory according to the instructions in cogent/README.
240 Configuration Options:
241 ----------------------
243 Configuration depends on the combination of board and CPU type; all
244 such information is kept in a configuration file
245 "include/configs/<board_name>.h".
247 Example: For a TQM823L module, all configuration settings are in
248 "include/configs/TQM823L.h".
251 Many of the options are named exactly as the corresponding Linux
252 kernel configuration options. The intention is to make it easier to
253 build a config tool - later.
256 The following options need to be configured:
258 - CPU Type: Define exactly one, e.g. CONFIG_MPC85XX.
260 - Board Type: Define exactly one, e.g. CONFIG_MPC8540ADS.
262 - CPU Daughterboard Type: (if CONFIG_ATSTK1000 is defined)
263 Define exactly one, e.g. CONFIG_ATSTK1002
265 - CPU Module Type: (if CONFIG_COGENT is defined)
266 Define exactly one of
268 --- FIXME --- not tested yet:
269 CONFIG_CMA286_60, CONFIG_CMA286_21, CONFIG_CMA286_60P,
270 CONFIG_CMA287_23, CONFIG_CMA287_50
272 - Motherboard Type: (if CONFIG_COGENT is defined)
273 Define exactly one of
274 CONFIG_CMA101, CONFIG_CMA102
276 - Motherboard I/O Modules: (if CONFIG_COGENT is defined)
277 Define one or more of
280 - Motherboard Options: (if CONFIG_CMA101 or CONFIG_CMA102 are defined)
281 Define one or more of
282 CONFIG_LCD_HEARTBEAT - update a character position on
283 the LCD display every second with
286 - Board flavour: (if CONFIG_MPC8260ADS is defined)
289 CONFIG_SYS_8260ADS - original MPC8260ADS
290 CONFIG_SYS_8266ADS - MPC8266ADS
291 CONFIG_SYS_PQ2FADS - PQ2FADS-ZU or PQ2FADS-VR
292 CONFIG_SYS_8272ADS - MPC8272ADS
294 - MPC824X Family Member (if CONFIG_MPC824X is defined)
295 Define exactly one of
296 CONFIG_MPC8240, CONFIG_MPC8245
298 - 8xx CPU Options: (if using an MPC8xx CPU)
299 CONFIG_8xx_GCLK_FREQ - deprecated: CPU clock if
300 get_gclk_freq() cannot work
301 e.g. if there is no 32KHz
302 reference PIT/RTC clock
303 CONFIG_8xx_OSCLK - PLL input clock (either EXTCLK
306 - 859/866/885 CPU options: (if using a MPC859 or MPC866 or MPC885 CPU):
307 CONFIG_SYS_8xx_CPUCLK_MIN
308 CONFIG_SYS_8xx_CPUCLK_MAX
309 CONFIG_8xx_CPUCLK_DEFAULT
310 See doc/README.MPC866
312 CONFIG_SYS_MEASURE_CPUCLK
314 Define this to measure the actual CPU clock instead
315 of relying on the correctness of the configured
316 values. Mostly useful for board bringup to make sure
317 the PLL is locked at the intended frequency. Note
318 that this requires a (stable) reference clock (32 kHz
319 RTC clock or CONFIG_SYS_8XX_XIN)
321 - Intel Monahans options:
322 CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO
324 Defines the Monahans run mode to oscillator
325 ratio. Valid values are 8, 16, 24, 31. The core
326 frequency is this value multiplied by 13 MHz.
328 CONFIG_SYS_MONAHANS_TURBO_RUN_MODE_RATIO
330 Defines the Monahans turbo mode to oscillator
331 ratio. Valid values are 1 (default if undefined) and
332 2. The core frequency as calculated above is multiplied
335 - Linux Kernel Interface:
338 U-Boot stores all clock information in Hz
339 internally. For binary compatibility with older Linux
340 kernels (which expect the clocks passed in the
341 bd_info data to be in MHz) the environment variable
342 "clocks_in_mhz" can be defined so that U-Boot
343 converts clock data to MHZ before passing it to the
345 When CONFIG_CLOCKS_IN_MHZ is defined, a definition of
346 "clocks_in_mhz=1" is automatically included in the
349 CONFIG_MEMSIZE_IN_BYTES [relevant for MIPS only]
351 When transferring memsize parameter to linux, some versions
352 expect it to be in bytes, others in MB.
353 Define CONFIG_MEMSIZE_IN_BYTES to make it in bytes.
357 New kernel versions are expecting firmware settings to be
358 passed using flattened device trees (based on open firmware
362 * New libfdt-based support
363 * Adds the "fdt" command
364 * The bootm command automatically updates the fdt
366 OF_CPU - The proper name of the cpus node.
367 OF_SOC - The proper name of the soc node.
368 OF_TBCLK - The timebase frequency.
369 OF_STDOUT_PATH - The path to the console device
371 boards with QUICC Engines require OF_QE to set UCC MAC
374 CONFIG_OF_BOARD_SETUP
376 Board code has addition modification that it wants to make
377 to the flat device tree before handing it off to the kernel
381 This define fills in the correct boot CPU in the boot
382 param header, the default value is zero if undefined.
384 - vxWorks boot parameters:
386 bootvx constructs a valid bootline using the following
387 environments variables: bootfile, ipaddr, serverip, hostname.
388 It loads the vxWorks image pointed bootfile.
390 CONFIG_SYS_VXWORKS_BOOT_DEVICE - The vxworks device name
391 CONFIG_SYS_VXWORKS_MAC_PTR - Ethernet 6 byte MA -address
392 CONFIG_SYS_VXWORKS_SERVERNAME - Name of the server
393 CONFIG_SYS_VXWORKS_BOOT_ADDR - Address of boot parameters
395 CONFIG_SYS_VXWORKS_ADD_PARAMS
397 Add it at the end of the bootline. E.g "u=username pw=secret"
399 Note: If a "bootargs" environment is defined, it will overwride
400 the defaults discussed just above.
405 Define this if you want support for Amba PrimeCell PL010 UARTs.
409 Define this if you want support for Amba PrimeCell PL011 UARTs.
413 If you have Amba PrimeCell PL011 UARTs, set this variable to
414 the clock speed of the UARTs.
418 If you have Amba PrimeCell PL010 or PL011 UARTs on your board,
419 define this to a list of base addresses for each (supported)
420 port. See e.g. include/configs/versatile.h
424 Depending on board, define exactly one serial port
425 (like CONFIG_8xx_CONS_SMC1, CONFIG_8xx_CONS_SMC2,
426 CONFIG_8xx_CONS_SCC1, ...), or switch off the serial
427 console by defining CONFIG_8xx_CONS_NONE
429 Note: if CONFIG_8xx_CONS_NONE is defined, the serial
430 port routines must be defined elsewhere
431 (i.e. serial_init(), serial_getc(), ...)
434 Enables console device for a color framebuffer. Needs following
435 defines (cf. smiLynxEM, i8042, board/eltec/bab7xx)
436 VIDEO_FB_LITTLE_ENDIAN graphic memory organisation
438 VIDEO_HW_RECTFILL graphic chip supports
441 VIDEO_HW_BITBLT graphic chip supports
442 bit-blit (cf. smiLynxEM)
443 VIDEO_VISIBLE_COLS visible pixel columns
445 VIDEO_VISIBLE_ROWS visible pixel rows
446 VIDEO_PIXEL_SIZE bytes per pixel
447 VIDEO_DATA_FORMAT graphic data format
448 (0-5, cf. cfb_console.c)
449 VIDEO_FB_ADRS framebuffer address
450 VIDEO_KBD_INIT_FCT keyboard int fct
451 (i.e. i8042_kbd_init())
452 VIDEO_TSTC_FCT test char fct
454 VIDEO_GETC_FCT get char fct
456 CONFIG_CONSOLE_CURSOR cursor drawing on/off
457 (requires blink timer
459 CONFIG_SYS_CONSOLE_BLINK_COUNT blink interval (cf. i8042.c)
460 CONFIG_CONSOLE_TIME display time/date info in
462 (requires CONFIG_CMD_DATE)
463 CONFIG_VIDEO_LOGO display Linux logo in
465 CONFIG_VIDEO_BMP_LOGO use bmp_logo.h instead of
466 linux_logo.h for logo.
467 Requires CONFIG_VIDEO_LOGO
468 CONFIG_CONSOLE_EXTRA_INFO
469 additional board info beside
472 When CONFIG_CFB_CONSOLE is defined, video console is
473 default i/o. Serial console can be forced with
474 environment 'console=serial'.
476 When CONFIG_SILENT_CONSOLE is defined, all console
477 messages (by U-Boot and Linux!) can be silenced with
478 the "silent" environment variable. See
479 doc/README.silent for more information.
482 CONFIG_BAUDRATE - in bps
483 Select one of the baudrates listed in
484 CONFIG_SYS_BAUDRATE_TABLE, see below.
485 CONFIG_SYS_BRGCLK_PRESCALE, baudrate prescale
487 - Console Rx buffer length
488 With CONFIG_SYS_SMC_RXBUFLEN it is possible to define
489 the maximum receive buffer length for the SMC.
490 This option is actual only for 82xx and 8xx possible.
491 If using CONFIG_SYS_SMC_RXBUFLEN also CONFIG_SYS_MAXIDLE
492 must be defined, to setup the maximum idle timeout for
495 - Interrupt driven serial port input:
496 CONFIG_SERIAL_SOFTWARE_FIFO
499 Use an interrupt handler for receiving data on the
500 serial port. It also enables using hardware handshake
501 (RTS/CTS) and UART's built-in FIFO. Set the number of
502 bytes the interrupt driven input buffer should have.
504 Leave undefined to disable this feature, including
505 disable the buffer and hardware handshake.
507 - Console UART Number:
511 If defined internal UART1 (and not UART0) is used
512 as default U-Boot console.
514 - Boot Delay: CONFIG_BOOTDELAY - in seconds
515 Delay before automatically booting the default image;
516 set to -1 to disable autoboot.
518 See doc/README.autoboot for these options that
519 work with CONFIG_BOOTDELAY. None are required.
520 CONFIG_BOOT_RETRY_TIME
521 CONFIG_BOOT_RETRY_MIN
522 CONFIG_AUTOBOOT_KEYED
523 CONFIG_AUTOBOOT_PROMPT
524 CONFIG_AUTOBOOT_DELAY_STR
525 CONFIG_AUTOBOOT_STOP_STR
526 CONFIG_AUTOBOOT_DELAY_STR2
527 CONFIG_AUTOBOOT_STOP_STR2
528 CONFIG_ZERO_BOOTDELAY_CHECK
529 CONFIG_RESET_TO_RETRY
533 Only needed when CONFIG_BOOTDELAY is enabled;
534 define a command string that is automatically executed
535 when no character is read on the console interface
536 within "Boot Delay" after reset.
539 This can be used to pass arguments to the bootm
540 command. The value of CONFIG_BOOTARGS goes into the
541 environment value "bootargs".
543 CONFIG_RAMBOOT and CONFIG_NFSBOOT
544 The value of these goes into the environment as
545 "ramboot" and "nfsboot" respectively, and can be used
546 as a convenience, when switching between booting from
552 When this option is #defined, the existence of the
553 environment variable "preboot" will be checked
554 immediately before starting the CONFIG_BOOTDELAY
555 countdown and/or running the auto-boot command resp.
556 entering interactive mode.
558 This feature is especially useful when "preboot" is
559 automatically generated or modified. For an example
560 see the LWMON board specific code: here "preboot" is
561 modified when the user holds down a certain
562 combination of keys on the (special) keyboard when
565 - Serial Download Echo Mode:
567 If defined to 1, all characters received during a
568 serial download (using the "loads" command) are
569 echoed back. This might be needed by some terminal
570 emulations (like "cu"), but may as well just take
571 time on others. This setting #define's the initial
572 value of the "loads_echo" environment variable.
574 - Kgdb Serial Baudrate: (if CONFIG_CMD_KGDB is defined)
576 Select one of the baudrates listed in
577 CONFIG_SYS_BAUDRATE_TABLE, see below.
580 Monitor commands can be included or excluded
581 from the build by using the #include files
582 "config_cmd_all.h" and #undef'ing unwanted
583 commands, or using "config_cmd_default.h"
584 and augmenting with additional #define's
587 The default command configuration includes all commands
588 except those marked below with a "*".
590 CONFIG_CMD_ASKENV * ask for env variable
591 CONFIG_CMD_AUTOSCRIPT Autoscript Support
592 CONFIG_CMD_BDI bdinfo
593 CONFIG_CMD_BEDBUG * Include BedBug Debugger
594 CONFIG_CMD_BMP * BMP support
595 CONFIG_CMD_BSP * Board specific commands
596 CONFIG_CMD_BOOTD bootd
597 CONFIG_CMD_CACHE * icache, dcache
598 CONFIG_CMD_CONSOLE coninfo
599 CONFIG_CMD_DATE * support for RTC, date/time...
600 CONFIG_CMD_DHCP * DHCP support
601 CONFIG_CMD_DIAG * Diagnostics
602 CONFIG_CMD_DOC * Disk-On-Chip Support
603 CONFIG_CMD_DS4510 * ds4510 I2C gpio commands
604 CONFIG_CMD_DS4510_INFO * ds4510 I2C info command
605 CONFIG_CMD_DS4510_MEM * ds4510 I2C eeprom/sram commansd
606 CONFIG_CMD_DS4510_RST * ds4510 I2C rst command
607 CONFIG_CMD_DTT * Digital Therm and Thermostat
608 CONFIG_CMD_ECHO echo arguments
609 CONFIG_CMD_EEPROM * EEPROM read/write support
610 CONFIG_CMD_ELF * bootelf, bootvx
611 CONFIG_CMD_SAVEENV saveenv
612 CONFIG_CMD_FDC * Floppy Disk Support
613 CONFIG_CMD_FAT * FAT partition support
614 CONFIG_CMD_FDOS * Dos diskette Support
615 CONFIG_CMD_FLASH flinfo, erase, protect
616 CONFIG_CMD_FPGA FPGA device initialization support
617 CONFIG_CMD_HWFLOW * RTS/CTS hw flow control
618 CONFIG_CMD_I2C * I2C serial bus support
619 CONFIG_CMD_IDE * IDE harddisk support
620 CONFIG_CMD_IMI iminfo
621 CONFIG_CMD_IMLS List all found images
622 CONFIG_CMD_IMMAP * IMMR dump support
623 CONFIG_CMD_IRQ * irqinfo
624 CONFIG_CMD_ITEST Integer/string test of 2 values
625 CONFIG_CMD_JFFS2 * JFFS2 Support
626 CONFIG_CMD_KGDB * kgdb
627 CONFIG_CMD_LOADB loadb
628 CONFIG_CMD_LOADS loads
629 CONFIG_CMD_MEMORY md, mm, nm, mw, cp, cmp, crc, base,
631 CONFIG_CMD_MISC Misc functions like sleep etc
632 CONFIG_CMD_MMC * MMC memory mapped support
633 CONFIG_CMD_MII * MII utility commands
634 CONFIG_CMD_NAND * NAND support
635 CONFIG_CMD_NET bootp, tftpboot, rarpboot
636 CONFIG_CMD_PCA953X * PCA953x I2C gpio commands
637 CONFIG_CMD_PCA953X_INFO * PCA953x I2C gpio info command
638 CONFIG_CMD_PCI * pciinfo
639 CONFIG_CMD_PCMCIA * PCMCIA support
640 CONFIG_CMD_PING * send ICMP ECHO_REQUEST to network
642 CONFIG_CMD_PORTIO * Port I/O
643 CONFIG_CMD_REGINFO * Register dump
644 CONFIG_CMD_RUN run command in env variable
645 CONFIG_CMD_SAVES * save S record dump
646 CONFIG_CMD_SCSI * SCSI Support
647 CONFIG_CMD_SDRAM * print SDRAM configuration information
648 (requires CONFIG_CMD_I2C)
649 CONFIG_CMD_SETGETDCR Support for DCR Register access
651 CONFIG_CMD_SPI * SPI serial bus support
652 CONFIG_CMD_USB * USB support
653 CONFIG_CMD_VFD * VFD support (TRAB)
654 CONFIG_CMD_CDP * Cisco Discover Protocol support
655 CONFIG_CMD_FSL * Microblaze FSL support
658 EXAMPLE: If you want all functions except of network
659 support you can write:
661 #include "config_cmd_all.h"
662 #undef CONFIG_CMD_NET
665 fdt (flattened device tree) command: CONFIG_OF_LIBFDT
667 Note: Don't enable the "icache" and "dcache" commands
668 (configuration option CONFIG_CMD_CACHE) unless you know
669 what you (and your U-Boot users) are doing. Data
670 cache cannot be enabled on systems like the 8xx or
671 8260 (where accesses to the IMMR region must be
672 uncached), and it cannot be disabled on all other
673 systems where we (mis-) use the data cache to hold an
674 initial stack and some data.
677 XXX - this list needs to get updated!
681 If this variable is defined, it enables watchdog
682 support. There must be support in the platform specific
683 code for a watchdog. For the 8xx and 8260 CPUs, the
684 SIU Watchdog feature is enabled in the SYPCR
688 CONFIG_VERSION_VARIABLE
689 If this variable is defined, an environment variable
690 named "ver" is created by U-Boot showing the U-Boot
691 version as printed by the "version" command.
692 This variable is readonly.
696 When CONFIG_CMD_DATE is selected, the type of the RTC
697 has to be selected, too. Define exactly one of the
700 CONFIG_RTC_MPC8xx - use internal RTC of MPC8xx
701 CONFIG_RTC_PCF8563 - use Philips PCF8563 RTC
702 CONFIG_RTC_MC13783 - use MC13783 RTC
703 CONFIG_RTC_MC146818 - use MC146818 RTC
704 CONFIG_RTC_DS1307 - use Maxim, Inc. DS1307 RTC
705 CONFIG_RTC_DS1337 - use Maxim, Inc. DS1337 RTC
706 CONFIG_RTC_DS1338 - use Maxim, Inc. DS1338 RTC
707 CONFIG_RTC_DS164x - use Dallas DS164x RTC
708 CONFIG_RTC_ISL1208 - use Intersil ISL1208 RTC
709 CONFIG_RTC_MAX6900 - use Maxim, Inc. MAX6900 RTC
710 CONFIG_SYS_RTC_DS1337_NOOSC - Turn off the OSC output for DS1337
712 Note that if the RTC uses I2C, then the I2C interface
713 must also be configured. See I2C Support, below.
716 CONFIG_PCA953X - use NXP's PCA953X series I2C GPIO
717 CONFIG_PCA953X_INFO - enable pca953x info command
719 Note that if the GPIO device uses I2C, then the I2C interface
720 must also be configured. See I2C Support, below.
724 When CONFIG_TIMESTAMP is selected, the timestamp
725 (date and time) of an image is printed by image
726 commands like bootm or iminfo. This option is
727 automatically enabled when you select CONFIG_CMD_DATE .
730 CONFIG_MAC_PARTITION and/or CONFIG_DOS_PARTITION
731 and/or CONFIG_ISO_PARTITION and/or CONFIG_EFI_PARTITION
733 If IDE or SCSI support is enabled (CONFIG_CMD_IDE or
734 CONFIG_CMD_SCSI) you must configure support for at
735 least one partition type as well.
738 CONFIG_IDE_RESET_ROUTINE - this is defined in several
739 board configurations files but used nowhere!
741 CONFIG_IDE_RESET - is this is defined, IDE Reset will
742 be performed by calling the function
743 ide_set_reset(int reset)
744 which has to be defined in a board specific file
749 Set this to enable ATAPI support.
754 Set this to enable support for disks larger than 137GB
755 Also look at CONFIG_SYS_64BIT_LBA ,CONFIG_SYS_64BIT_VSPRINTF and CONFIG_SYS_64BIT_STRTOUL
756 Whithout these , LBA48 support uses 32bit variables and will 'only'
757 support disks up to 2.1TB.
759 CONFIG_SYS_64BIT_LBA:
760 When enabled, makes the IDE subsystem use 64bit sector addresses.
764 At the moment only there is only support for the
765 SYM53C8XX SCSI controller; define
766 CONFIG_SCSI_SYM53C8XX to enable it.
768 CONFIG_SYS_SCSI_MAX_LUN [8], CONFIG_SYS_SCSI_MAX_SCSI_ID [7] and
769 CONFIG_SYS_SCSI_MAX_DEVICE [CONFIG_SYS_SCSI_MAX_SCSI_ID *
770 CONFIG_SYS_SCSI_MAX_LUN] can be adjusted to define the
771 maximum numbers of LUNs, SCSI ID's and target
773 CONFIG_SYS_SCSI_SYM53C8XX_CCF to fix clock timing (80Mhz)
775 - NETWORK Support (PCI):
777 Support for Intel 8254x gigabit chips.
779 CONFIG_E1000_FALLBACK_MAC
780 default MAC for empty EEPROM after production.
783 Support for Intel 82557/82559/82559ER chips.
784 Optional CONFIG_EEPRO100_SROM_WRITE enables EEPROM
785 write routine for first time initialisation.
788 Support for Digital 2114x chips.
789 Optional CONFIG_TULIP_SELECT_MEDIA for board specific
790 modem chip initialisation (KS8761/QS6611).
793 Support for National dp83815 chips.
796 Support for National dp8382[01] gigabit chips.
798 - NETWORK Support (other):
800 CONFIG_DRIVER_LAN91C96
801 Support for SMSC's LAN91C96 chips.
804 Define this to hold the physical address
805 of the LAN91C96's I/O space
807 CONFIG_LAN91C96_USE_32_BIT
808 Define this to enable 32 bit addressing
810 CONFIG_DRIVER_SMC91111
811 Support for SMSC's LAN91C111 chip
814 Define this to hold the physical address
815 of the device (I/O space)
817 CONFIG_SMC_USE_32_BIT
818 Define this if data bus is 32 bits
820 CONFIG_SMC_USE_IOFUNCS
821 Define this to use i/o functions instead of macros
822 (some hardware wont work with macros)
824 CONFIG_DRIVER_SMC911X
825 Support for SMSC's LAN911x and LAN921x chips
827 CONFIG_DRIVER_SMC911X_BASE
828 Define this to hold the physical address
829 of the device (I/O space)
831 CONFIG_DRIVER_SMC911X_32_BIT
832 Define this if data bus is 32 bits
834 CONFIG_DRIVER_SMC911X_16_BIT
835 Define this if data bus is 16 bits. If your processor
836 automatically converts one 32 bit word to two 16 bit
837 words you may also try CONFIG_DRIVER_SMC911X_32_BIT.
840 At the moment only the UHCI host controller is
841 supported (PIP405, MIP405, MPC5200); define
842 CONFIG_USB_UHCI to enable it.
843 define CONFIG_USB_KEYBOARD to enable the USB Keyboard
844 and define CONFIG_USB_STORAGE to enable the USB
847 Supported are USB Keyboards and USB Floppy drives
849 MPC5200 USB requires additional defines:
851 for 528 MHz Clock: 0x0001bbbb
853 for differential drivers: 0x00001000
854 for single ended drivers: 0x00005000
855 CONFIG_SYS_USB_EVENT_POLL
856 May be defined to allow interrupt polling
857 instead of using asynchronous interrupts
860 Define the below if you wish to use the USB console.
861 Once firmware is rebuilt from a serial console issue the
862 command "setenv stdin usbtty; setenv stdout usbtty" and
863 attach your USB cable. The Unix command "dmesg" should print
864 it has found a new device. The environment variable usbtty
865 can be set to gserial or cdc_acm to enable your device to
866 appear to a USB host as a Linux gserial device or a
867 Common Device Class Abstract Control Model serial device.
868 If you select usbtty = gserial you should be able to enumerate
870 # modprobe usbserial vendor=0xVendorID product=0xProductID
871 else if using cdc_acm, simply setting the environment
872 variable usbtty to be cdc_acm should suffice. The following
873 might be defined in YourBoardName.h
876 Define this to build a UDC device
879 Define this to have a tty type of device available to
880 talk to the UDC device
882 CONFIG_SYS_CONSOLE_IS_IN_ENV
883 Define this if you want stdin, stdout &/or stderr to
887 CONFIG_SYS_USB_EXTC_CLK 0xBLAH
888 Derive USB clock from external clock "blah"
889 - CONFIG_SYS_USB_EXTC_CLK 0x02
891 CONFIG_SYS_USB_BRG_CLK 0xBLAH
892 Derive USB clock from brgclk
893 - CONFIG_SYS_USB_BRG_CLK 0x04
895 If you have a USB-IF assigned VendorID then you may wish to
896 define your own vendor specific values either in BoardName.h
897 or directly in usbd_vendor_info.h. If you don't define
898 CONFIG_USBD_MANUFACTURER, CONFIG_USBD_PRODUCT_NAME,
899 CONFIG_USBD_VENDORID and CONFIG_USBD_PRODUCTID, then U-Boot
900 should pretend to be a Linux device to it's target host.
902 CONFIG_USBD_MANUFACTURER
903 Define this string as the name of your company for
904 - CONFIG_USBD_MANUFACTURER "my company"
906 CONFIG_USBD_PRODUCT_NAME
907 Define this string as the name of your product
908 - CONFIG_USBD_PRODUCT_NAME "acme usb device"
911 Define this as your assigned Vendor ID from the USB
912 Implementors Forum. This *must* be a genuine Vendor ID
913 to avoid polluting the USB namespace.
914 - CONFIG_USBD_VENDORID 0xFFFF
916 CONFIG_USBD_PRODUCTID
917 Define this as the unique Product ID
919 - CONFIG_USBD_PRODUCTID 0xFFFF
923 The MMC controller on the Intel PXA is supported. To
924 enable this define CONFIG_MMC. The MMC can be
925 accessed from the boot prompt by mapping the device
926 to physical memory similar to flash. Command line is
927 enabled with CONFIG_CMD_MMC. The MMC driver also works with
928 the FAT fs. This is enabled with CONFIG_CMD_FAT.
930 - Journaling Flash filesystem support:
931 CONFIG_JFFS2_NAND, CONFIG_JFFS2_NAND_OFF, CONFIG_JFFS2_NAND_SIZE,
932 CONFIG_JFFS2_NAND_DEV
933 Define these for a default partition on a NAND device
935 CONFIG_SYS_JFFS2_FIRST_SECTOR,
936 CONFIG_SYS_JFFS2_FIRST_BANK, CONFIG_SYS_JFFS2_NUM_BANKS
937 Define these for a default partition on a NOR device
939 CONFIG_SYS_JFFS_CUSTOM_PART
940 Define this to create an own partition. You have to provide a
941 function struct part_info* jffs2_part_info(int part_num)
943 If you define only one JFFS2 partition you may also want to
944 #define CONFIG_SYS_JFFS_SINGLE_PART 1
945 to disable the command chpart. This is the default when you
946 have not defined a custom partition
951 Define this to enable standard (PC-Style) keyboard
955 Standard PC keyboard driver with US (is default) and
956 GERMAN key layout (switch via environment 'keymap=de') support.
957 Export function i8042_kbd_init, i8042_tstc and i8042_getc
958 for cfb_console. Supports cursor blinking.
963 Define this to enable video support (for output to
968 Enable Chips & Technologies 69000 Video chip
970 CONFIG_VIDEO_SMI_LYNXEM
971 Enable Silicon Motion SMI 712/710/810 Video chip. The
972 video output is selected via environment 'videoout'
973 (1 = LCD and 2 = CRT). If videoout is undefined, CRT is
976 For the CT69000 and SMI_LYNXEM drivers, videomode is
977 selected via environment 'videomode'. Two different ways
979 - "videomode=num" 'num' is a standard LiLo mode numbers.
980 Following standard modes are supported (* is default):
982 Colors 640x480 800x600 1024x768 1152x864 1280x1024
983 -------------+---------------------------------------------
984 8 bits | 0x301* 0x303 0x305 0x161 0x307
985 15 bits | 0x310 0x313 0x316 0x162 0x319
986 16 bits | 0x311 0x314 0x317 0x163 0x31A
987 24 bits | 0x312 0x315 0x318 ? 0x31B
988 -------------+---------------------------------------------
989 (i.e. setenv videomode 317; saveenv; reset;)
991 - "videomode=bootargs" all the video parameters are parsed
992 from the bootargs. (See drivers/video/videomodes.c)
995 CONFIG_VIDEO_SED13806
996 Enable Epson SED13806 driver. This driver supports 8bpp
997 and 16bpp modes defined by CONFIG_VIDEO_SED13806_8BPP
998 or CONFIG_VIDEO_SED13806_16BPP
1003 Define this to enable a custom keyboard support.
1004 This simply calls drv_keyboard_init() which must be
1005 defined in your board-specific files.
1006 The only board using this so far is RBC823.
1008 - LCD Support: CONFIG_LCD
1010 Define this to enable LCD support (for output to LCD
1011 display); also select one of the supported displays
1012 by defining one of these:
1016 HITACHI TX09D70VM1CCA, 3.5", 240x320.
1018 CONFIG_NEC_NL6448AC33:
1020 NEC NL6448AC33-18. Active, color, single scan.
1022 CONFIG_NEC_NL6448BC20
1024 NEC NL6448BC20-08. 6.5", 640x480.
1025 Active, color, single scan.
1027 CONFIG_NEC_NL6448BC33_54
1029 NEC NL6448BC33-54. 10.4", 640x480.
1030 Active, color, single scan.
1034 Sharp 320x240. Active, color, single scan.
1035 It isn't 16x9, and I am not sure what it is.
1037 CONFIG_SHARP_LQ64D341
1039 Sharp LQ64D341 display, 640x480.
1040 Active, color, single scan.
1044 HLD1045 display, 640x480.
1045 Active, color, single scan.
1049 Optrex CBL50840-2 NF-FW 99 22 M5
1051 Hitachi LMG6912RPFC-00T
1055 320x240. Black & white.
1057 Normally display is black on white background; define
1058 CONFIG_SYS_WHITE_ON_BLACK to get it inverted.
1060 - Splash Screen Support: CONFIG_SPLASH_SCREEN
1062 If this option is set, the environment is checked for
1063 a variable "splashimage". If found, the usual display
1064 of logo, copyright and system information on the LCD
1065 is suppressed and the BMP image at the address
1066 specified in "splashimage" is loaded instead. The
1067 console is redirected to the "nulldev", too. This
1068 allows for a "silent" boot where a splash screen is
1069 loaded very quickly after power-on.
1071 - Gzip compressed BMP image support: CONFIG_VIDEO_BMP_GZIP
1073 If this option is set, additionally to standard BMP
1074 images, gzipped BMP images can be displayed via the
1075 splashscreen support or the bmp command.
1077 - Compression support:
1080 If this option is set, support for bzip2 compressed
1081 images is included. If not, only uncompressed and gzip
1082 compressed images are supported.
1084 NOTE: the bzip2 algorithm requires a lot of RAM, so
1085 the malloc area (as defined by CONFIG_SYS_MALLOC_LEN) should
1090 If this option is set, support for lzma compressed
1093 Note: The LZMA algorithm adds between 2 and 4KB of code and it
1094 requires an amount of dynamic memory that is given by the
1097 (1846 + 768 << (lc + lp)) * sizeof(uint16)
1099 Where lc and lp stand for, respectively, Literal context bits
1100 and Literal pos bits.
1102 This value is upper-bounded by 14MB in the worst case. Anyway,
1103 for a ~4MB large kernel image, we have lc=3 and lp=0 for a
1104 total amount of (1846 + 768 << (3 + 0)) * 2 = ~41KB... that is
1105 a very small buffer.
1107 Use the lzmainfo tool to determinate the lc and lp values and
1108 then calculate the amount of needed dynamic memory (ensuring
1109 the appropriate CONFIG_SYS_MALLOC_LEN value).
1114 The address of PHY on MII bus.
1116 CONFIG_PHY_CLOCK_FREQ (ppc4xx)
1118 The clock frequency of the MII bus
1122 If this option is set, support for speed/duplex
1123 detection of gigabit PHY is included.
1125 CONFIG_PHY_RESET_DELAY
1127 Some PHY like Intel LXT971A need extra delay after
1128 reset before any MII register access is possible.
1129 For such PHY, set this option to the usec delay
1130 required. (minimum 300usec for LXT971A)
1132 CONFIG_PHY_CMD_DELAY (ppc4xx)
1134 Some PHY like Intel LXT971A need extra delay after
1135 command issued before MII status register can be read
1145 Define a default value for Ethernet address to use
1146 for the respective Ethernet interface, in case this
1147 is not determined automatically.
1152 Define a default value for the IP address to use for
1153 the default Ethernet interface, in case this is not
1154 determined through e.g. bootp.
1156 - Server IP address:
1159 Defines a default value for the IP address of a TFTP
1160 server to contact when using the "tftboot" command.
1162 - Multicast TFTP Mode:
1165 Defines whether you want to support multicast TFTP as per
1166 rfc-2090; for example to work with atftp. Lets lots of targets
1167 tftp down the same boot image concurrently. Note: the Ethernet
1168 driver in use must provide a function: mcast() to join/leave a
1171 CONFIG_BOOTP_RANDOM_DELAY
1172 - BOOTP Recovery Mode:
1173 CONFIG_BOOTP_RANDOM_DELAY
1175 If you have many targets in a network that try to
1176 boot using BOOTP, you may want to avoid that all
1177 systems send out BOOTP requests at precisely the same
1178 moment (which would happen for instance at recovery
1179 from a power failure, when all systems will try to
1180 boot, thus flooding the BOOTP server. Defining
1181 CONFIG_BOOTP_RANDOM_DELAY causes a random delay to be
1182 inserted before sending out BOOTP requests. The
1183 following delays are inserted then:
1185 1st BOOTP request: delay 0 ... 1 sec
1186 2nd BOOTP request: delay 0 ... 2 sec
1187 3rd BOOTP request: delay 0 ... 4 sec
1189 BOOTP requests: delay 0 ... 8 sec
1191 - DHCP Advanced Options:
1192 You can fine tune the DHCP functionality by defining
1193 CONFIG_BOOTP_* symbols:
1195 CONFIG_BOOTP_SUBNETMASK
1196 CONFIG_BOOTP_GATEWAY
1197 CONFIG_BOOTP_HOSTNAME
1198 CONFIG_BOOTP_NISDOMAIN
1199 CONFIG_BOOTP_BOOTPATH
1200 CONFIG_BOOTP_BOOTFILESIZE
1203 CONFIG_BOOTP_SEND_HOSTNAME
1204 CONFIG_BOOTP_NTPSERVER
1205 CONFIG_BOOTP_TIMEOFFSET
1206 CONFIG_BOOTP_VENDOREX
1208 CONFIG_BOOTP_SERVERIP - TFTP server will be the serverip
1209 environment variable, not the BOOTP server.
1211 CONFIG_BOOTP_DNS2 - If a DHCP client requests the DNS
1212 serverip from a DHCP server, it is possible that more
1213 than one DNS serverip is offered to the client.
1214 If CONFIG_BOOTP_DNS2 is enabled, the secondary DNS
1215 serverip will be stored in the additional environment
1216 variable "dnsip2". The first DNS serverip is always
1217 stored in the variable "dnsip", when CONFIG_BOOTP_DNS
1220 CONFIG_BOOTP_SEND_HOSTNAME - Some DHCP servers are capable
1221 to do a dynamic update of a DNS server. To do this, they
1222 need the hostname of the DHCP requester.
1223 If CONFIG_BOOTP_SEND_HOSTNAME is defined, the content
1224 of the "hostname" environment variable is passed as
1225 option 12 to the DHCP server.
1227 CONFIG_BOOTP_DHCP_REQUEST_DELAY
1229 A 32bit value in microseconds for a delay between
1230 receiving a "DHCP Offer" and sending the "DHCP Request".
1231 This fixes a problem with certain DHCP servers that don't
1232 respond 100% of the time to a "DHCP request". E.g. On an
1233 AT91RM9200 processor running at 180MHz, this delay needed
1234 to be *at least* 15,000 usec before a Windows Server 2003
1235 DHCP server would reply 100% of the time. I recommend at
1236 least 50,000 usec to be safe. The alternative is to hope
1237 that one of the retries will be successful but note that
1238 the DHCP timeout and retry process takes a longer than
1242 CONFIG_CDP_DEVICE_ID
1244 The device id used in CDP trigger frames.
1246 CONFIG_CDP_DEVICE_ID_PREFIX
1248 A two character string which is prefixed to the MAC address
1253 A printf format string which contains the ascii name of
1254 the port. Normally is set to "eth%d" which sets
1255 eth0 for the first Ethernet, eth1 for the second etc.
1257 CONFIG_CDP_CAPABILITIES
1259 A 32bit integer which indicates the device capabilities;
1260 0x00000010 for a normal host which does not forwards.
1264 An ascii string containing the version of the software.
1268 An ascii string containing the name of the platform.
1272 A 32bit integer sent on the trigger.
1274 CONFIG_CDP_POWER_CONSUMPTION
1276 A 16bit integer containing the power consumption of the
1277 device in .1 of milliwatts.
1279 CONFIG_CDP_APPLIANCE_VLAN_TYPE
1281 A byte containing the id of the VLAN.
1283 - Status LED: CONFIG_STATUS_LED
1285 Several configurations allow to display the current
1286 status using a LED. For instance, the LED will blink
1287 fast while running U-Boot code, stop blinking as
1288 soon as a reply to a BOOTP request was received, and
1289 start blinking slow once the Linux kernel is running
1290 (supported by a status LED driver in the Linux
1291 kernel). Defining CONFIG_STATUS_LED enables this
1294 - CAN Support: CONFIG_CAN_DRIVER
1296 Defining CONFIG_CAN_DRIVER enables CAN driver support
1297 on those systems that support this (optional)
1298 feature, like the TQM8xxL modules.
1300 - I2C Support: CONFIG_HARD_I2C | CONFIG_SOFT_I2C
1302 These enable I2C serial bus commands. Defining either of
1303 (but not both of) CONFIG_HARD_I2C or CONFIG_SOFT_I2C will
1304 include the appropriate I2C driver for the selected CPU.
1306 This will allow you to use i2c commands at the u-boot
1307 command line (as long as you set CONFIG_CMD_I2C in
1308 CONFIG_COMMANDS) and communicate with i2c based realtime
1309 clock chips. See common/cmd_i2c.c for a description of the
1310 command line interface.
1312 CONFIG_I2C_CMD_TREE is a recommended option that places
1313 all I2C commands under a single 'i2c' root command. The
1314 older 'imm', 'imd', 'iprobe' etc. commands are considered
1315 deprecated and may disappear in the future.
1317 CONFIG_HARD_I2C selects a hardware I2C controller.
1319 CONFIG_SOFT_I2C configures u-boot to use a software (aka
1320 bit-banging) driver instead of CPM or similar hardware
1323 There are several other quantities that must also be
1324 defined when you define CONFIG_HARD_I2C or CONFIG_SOFT_I2C.
1326 In both cases you will need to define CONFIG_SYS_I2C_SPEED
1327 to be the frequency (in Hz) at which you wish your i2c bus
1328 to run and CONFIG_SYS_I2C_SLAVE to be the address of this node (ie
1329 the CPU's i2c node address).
1331 Now, the u-boot i2c code for the mpc8xx (cpu/mpc8xx/i2c.c)
1332 sets the CPU up as a master node and so its address should
1333 therefore be cleared to 0 (See, eg, MPC823e User's Manual
1334 p.16-473). So, set CONFIG_SYS_I2C_SLAVE to 0.
1336 That's all that's required for CONFIG_HARD_I2C.
1338 If you use the software i2c interface (CONFIG_SOFT_I2C)
1339 then the following macros need to be defined (examples are
1340 from include/configs/lwmon.h):
1344 (Optional). Any commands necessary to enable the I2C
1345 controller or configure ports.
1347 eg: #define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL)
1351 (Only for MPC8260 CPU). The I/O port to use (the code
1352 assumes both bits are on the same port). Valid values
1353 are 0..3 for ports A..D.
1357 The code necessary to make the I2C data line active
1358 (driven). If the data line is open collector, this
1361 eg: #define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA)
1365 The code necessary to make the I2C data line tri-stated
1366 (inactive). If the data line is open collector, this
1369 eg: #define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA)
1373 Code that returns TRUE if the I2C data line is high,
1376 eg: #define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
1380 If <bit> is TRUE, sets the I2C data line high. If it
1381 is FALSE, it clears it (low).
1383 eg: #define I2C_SDA(bit) \
1384 if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \
1385 else immr->im_cpm.cp_pbdat &= ~PB_SDA
1389 If <bit> is TRUE, sets the I2C clock line high. If it
1390 is FALSE, it clears it (low).
1392 eg: #define I2C_SCL(bit) \
1393 if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \
1394 else immr->im_cpm.cp_pbdat &= ~PB_SCL
1398 This delay is invoked four times per clock cycle so this
1399 controls the rate of data transfer. The data rate thus
1400 is 1 / (I2C_DELAY * 4). Often defined to be something
1403 #define I2C_DELAY udelay(2)
1405 CONFIG_SYS_I2C_INIT_BOARD
1407 When a board is reset during an i2c bus transfer
1408 chips might think that the current transfer is still
1409 in progress. On some boards it is possible to access
1410 the i2c SCLK line directly, either by using the
1411 processor pin as a GPIO or by having a second pin
1412 connected to the bus. If this option is defined a
1413 custom i2c_init_board() routine in boards/xxx/board.c
1414 is run early in the boot sequence.
1416 CONFIG_I2CFAST (PPC405GP|PPC405EP only)
1418 This option enables configuration of bi_iic_fast[] flags
1419 in u-boot bd_info structure based on u-boot environment
1420 variable "i2cfast". (see also i2cfast)
1422 CONFIG_I2C_MULTI_BUS
1424 This option allows the use of multiple I2C buses, each of which
1425 must have a controller. At any point in time, only one bus is
1426 active. To switch to a different bus, use the 'i2c dev' command.
1427 Note that bus numbering is zero-based.
1429 CONFIG_SYS_I2C_NOPROBES
1431 This option specifies a list of I2C devices that will be skipped
1432 when the 'i2c probe' command is issued (or 'iprobe' using the legacy
1433 command). If CONFIG_I2C_MULTI_BUS is set, specify a list of bus-device
1434 pairs. Otherwise, specify a 1D array of device addresses
1437 #undef CONFIG_I2C_MULTI_BUS
1438 #define CONFIG_SYS_I2C_NOPROBES {0x50,0x68}
1440 will skip addresses 0x50 and 0x68 on a board with one I2C bus
1442 #define CONFIG_I2C_MULTI_BUS
1443 #define CONFIG_SYS_I2C_MULTI_NOPROBES {{0,0x50},{0,0x68},{1,0x54}}
1445 will skip addresses 0x50 and 0x68 on bus 0 and address 0x54 on bus 1
1447 CONFIG_SYS_SPD_BUS_NUM
1449 If defined, then this indicates the I2C bus number for DDR SPD.
1450 If not defined, then U-Boot assumes that SPD is on I2C bus 0.
1452 CONFIG_SYS_RTC_BUS_NUM
1454 If defined, then this indicates the I2C bus number for the RTC.
1455 If not defined, then U-Boot assumes that RTC is on I2C bus 0.
1457 CONFIG_SYS_DTT_BUS_NUM
1459 If defined, then this indicates the I2C bus number for the DTT.
1460 If not defined, then U-Boot assumes that DTT is on I2C bus 0.
1462 CONFIG_SYS_I2C_DTT_ADDR:
1464 If defined, specifies the I2C address of the DTT device.
1465 If not defined, then U-Boot uses predefined value for
1466 specified DTT device.
1470 Define this option if you want to use Freescale's I2C driver in
1471 drivers/i2c/fsl_i2c.c.
1475 Define this option if you have I2C devices reached over 1 .. n
1476 I2C Muxes like the pca9544a. This option addes a new I2C
1477 Command "i2c bus [muxtype:muxaddr:muxchannel]" which adds a
1478 new I2C Bus to the existing I2C Busses. If you select the
1479 new Bus with "i2c dev", u-bbot sends first the commandos for
1480 the muxes to activate this new "bus".
1482 CONFIG_I2C_MULTI_BUS must be also defined, to use this
1486 Adding a new I2C Bus reached over 2 pca9544a muxes
1487 The First mux with address 70 and channel 6
1488 The Second mux with address 71 and channel 4
1490 => i2c bus pca9544a:70:6:pca9544a:71:4
1492 Use the "i2c bus" command without parameter, to get a list
1493 of I2C Busses with muxes:
1496 Busses reached over muxes:
1498 reached over Mux(es):
1501 reached over Mux(es):
1506 If you now switch to the new I2C Bus 3 with "i2c dev 3"
1507 u-boot sends First the Commando to the mux@70 to enable
1508 channel 6, and then the Commando to the mux@71 to enable
1511 After that, you can use the "normal" i2c commands as
1512 usual, to communicate with your I2C devices behind
1515 This option is actually implemented for the bitbanging
1516 algorithm in common/soft_i2c.c and for the Hardware I2C
1517 Bus on the MPC8260. But it should be not so difficult
1518 to add this option to other architectures.
1520 CONFIG_SOFT_I2C_READ_REPEATED_START
1522 defining this will force the i2c_read() function in
1523 the soft_i2c driver to perform an I2C repeated start
1524 between writing the address pointer and reading the
1525 data. If this define is omitted the default behaviour
1526 of doing a stop-start sequence will be used. Most I2C
1527 devices can use either method, but some require one or
1530 - SPI Support: CONFIG_SPI
1532 Enables SPI driver (so far only tested with
1533 SPI EEPROM, also an instance works with Crystal A/D and
1534 D/As on the SACSng board)
1538 Enables extended (16-bit) SPI EEPROM addressing.
1539 (symmetrical to CONFIG_I2C_X)
1543 Enables a software (bit-bang) SPI driver rather than
1544 using hardware support. This is a general purpose
1545 driver that only requires three general I/O port pins
1546 (two outputs, one input) to function. If this is
1547 defined, the board configuration must define several
1548 SPI configuration items (port pins to use, etc). For
1549 an example, see include/configs/sacsng.h.
1553 Enables a hardware SPI driver for general-purpose reads
1554 and writes. As with CONFIG_SOFT_SPI, the board configuration
1555 must define a list of chip-select function pointers.
1556 Currently supported on some MPC8xxx processors. For an
1557 example, see include/configs/mpc8349emds.h.
1561 Enables the driver for the SPI controllers on i.MX and MXC
1562 SoCs. Currently only i.MX31 is supported.
1564 - FPGA Support: CONFIG_FPGA
1566 Enables FPGA subsystem.
1568 CONFIG_FPGA_<vendor>
1570 Enables support for specific chip vendors.
1573 CONFIG_FPGA_<family>
1575 Enables support for FPGA family.
1576 (SPARTAN2, SPARTAN3, VIRTEX2, CYCLONE2, ACEX1K, ACEX)
1580 Specify the number of FPGA devices to support.
1582 CONFIG_SYS_FPGA_PROG_FEEDBACK
1584 Enable printing of hash marks during FPGA configuration.
1586 CONFIG_SYS_FPGA_CHECK_BUSY
1588 Enable checks on FPGA configuration interface busy
1589 status by the configuration function. This option
1590 will require a board or device specific function to
1595 If defined, a function that provides delays in the FPGA
1596 configuration driver.
1598 CONFIG_SYS_FPGA_CHECK_CTRLC
1599 Allow Control-C to interrupt FPGA configuration
1601 CONFIG_SYS_FPGA_CHECK_ERROR
1603 Check for configuration errors during FPGA bitfile
1604 loading. For example, abort during Virtex II
1605 configuration if the INIT_B line goes low (which
1606 indicated a CRC error).
1608 CONFIG_SYS_FPGA_WAIT_INIT
1610 Maximum time to wait for the INIT_B line to deassert
1611 after PROB_B has been deasserted during a Virtex II
1612 FPGA configuration sequence. The default time is 500
1615 CONFIG_SYS_FPGA_WAIT_BUSY
1617 Maximum time to wait for BUSY to deassert during
1618 Virtex II FPGA configuration. The default is 5 ms.
1620 CONFIG_SYS_FPGA_WAIT_CONFIG
1622 Time to wait after FPGA configuration. The default is
1625 - Configuration Management:
1628 If defined, this string will be added to the U-Boot
1629 version information (U_BOOT_VERSION)
1631 - Vendor Parameter Protection:
1633 U-Boot considers the values of the environment
1634 variables "serial#" (Board Serial Number) and
1635 "ethaddr" (Ethernet Address) to be parameters that
1636 are set once by the board vendor / manufacturer, and
1637 protects these variables from casual modification by
1638 the user. Once set, these variables are read-only,
1639 and write or delete attempts are rejected. You can
1640 change this behaviour:
1642 If CONFIG_ENV_OVERWRITE is #defined in your config
1643 file, the write protection for vendor parameters is
1644 completely disabled. Anybody can change or delete
1647 Alternatively, if you #define _both_ CONFIG_ETHADDR
1648 _and_ CONFIG_OVERWRITE_ETHADDR_ONCE, a default
1649 Ethernet address is installed in the environment,
1650 which can be changed exactly ONCE by the user. [The
1651 serial# is unaffected by this, i. e. it remains
1657 Define this variable to enable the reservation of
1658 "protected RAM", i. e. RAM which is not overwritten
1659 by U-Boot. Define CONFIG_PRAM to hold the number of
1660 kB you want to reserve for pRAM. You can overwrite
1661 this default value by defining an environment
1662 variable "pram" to the number of kB you want to
1663 reserve. Note that the board info structure will
1664 still show the full amount of RAM. If pRAM is
1665 reserved, a new environment variable "mem" will
1666 automatically be defined to hold the amount of
1667 remaining RAM in a form that can be passed as boot
1668 argument to Linux, for instance like that:
1670 setenv bootargs ... mem=\${mem}
1673 This way you can tell Linux not to use this memory,
1674 either, which results in a memory region that will
1675 not be affected by reboots.
1677 *WARNING* If your board configuration uses automatic
1678 detection of the RAM size, you must make sure that
1679 this memory test is non-destructive. So far, the
1680 following board configurations are known to be
1683 ETX094, IVMS8, IVML24, SPD8xx, TQM8xxL,
1684 HERMES, IP860, RPXlite, LWMON, LANTEC,
1685 PCU_E, FLAGADM, TQM8260
1690 Define this variable to stop the system in case of a
1691 fatal error, so that you have to reset it manually.
1692 This is probably NOT a good idea for an embedded
1693 system where you want the system to reboot
1694 automatically as fast as possible, but it may be
1695 useful during development since you can try to debug
1696 the conditions that lead to the situation.
1698 CONFIG_NET_RETRY_COUNT
1700 This variable defines the number of retries for
1701 network operations like ARP, RARP, TFTP, or BOOTP
1702 before giving up the operation. If not defined, a
1703 default value of 5 is used.
1707 Timeout waiting for an ARP reply in milliseconds.
1709 - Command Interpreter:
1710 CONFIG_AUTO_COMPLETE
1712 Enable auto completion of commands using TAB.
1714 Note that this feature has NOT been implemented yet
1715 for the "hush" shell.
1718 CONFIG_SYS_HUSH_PARSER
1720 Define this variable to enable the "hush" shell (from
1721 Busybox) as command line interpreter, thus enabling
1722 powerful command line syntax like
1723 if...then...else...fi conditionals or `&&' and '||'
1724 constructs ("shell scripts").
1726 If undefined, you get the old, much simpler behaviour
1727 with a somewhat smaller memory footprint.
1730 CONFIG_SYS_PROMPT_HUSH_PS2
1732 This defines the secondary prompt string, which is
1733 printed when the command interpreter needs more input
1734 to complete a command. Usually "> ".
1738 In the current implementation, the local variables
1739 space and global environment variables space are
1740 separated. Local variables are those you define by
1741 simply typing `name=value'. To access a local
1742 variable later on, you have write `$name' or
1743 `${name}'; to execute the contents of a variable
1744 directly type `$name' at the command prompt.
1746 Global environment variables are those you use
1747 setenv/printenv to work with. To run a command stored
1748 in such a variable, you need to use the run command,
1749 and you must not use the '$' sign to access them.
1751 To store commands and special characters in a
1752 variable, please use double quotation marks
1753 surrounding the whole text of the variable, instead
1754 of the backslashes before semicolons and special
1757 - Commandline Editing and History:
1758 CONFIG_CMDLINE_EDITING
1760 Enable editing and History functions for interactive
1761 commandline input operations
1763 - Default Environment:
1764 CONFIG_EXTRA_ENV_SETTINGS
1766 Define this to contain any number of null terminated
1767 strings (variable = value pairs) that will be part of
1768 the default environment compiled into the boot image.
1770 For example, place something like this in your
1771 board's config file:
1773 #define CONFIG_EXTRA_ENV_SETTINGS \
1777 Warning: This method is based on knowledge about the
1778 internal format how the environment is stored by the
1779 U-Boot code. This is NOT an official, exported
1780 interface! Although it is unlikely that this format
1781 will change soon, there is no guarantee either.
1782 You better know what you are doing here.
1784 Note: overly (ab)use of the default environment is
1785 discouraged. Make sure to check other ways to preset
1786 the environment like the autoscript function or the
1789 - DataFlash Support:
1790 CONFIG_HAS_DATAFLASH
1792 Defining this option enables DataFlash features and
1793 allows to read/write in Dataflash via the standard
1796 - SystemACE Support:
1799 Adding this option adds support for Xilinx SystemACE
1800 chips attached via some sort of local bus. The address
1801 of the chip must also be defined in the
1802 CONFIG_SYS_SYSTEMACE_BASE macro. For example:
1804 #define CONFIG_SYSTEMACE
1805 #define CONFIG_SYS_SYSTEMACE_BASE 0xf0000000
1807 When SystemACE support is added, the "ace" device type
1808 becomes available to the fat commands, i.e. fatls.
1810 - TFTP Fixed UDP Port:
1813 If this is defined, the environment variable tftpsrcp
1814 is used to supply the TFTP UDP source port value.
1815 If tftpsrcp isn't defined, the normal pseudo-random port
1816 number generator is used.
1818 Also, the environment variable tftpdstp is used to supply
1819 the TFTP UDP destination port value. If tftpdstp isn't
1820 defined, the normal port 69 is used.
1822 The purpose for tftpsrcp is to allow a TFTP server to
1823 blindly start the TFTP transfer using the pre-configured
1824 target IP address and UDP port. This has the effect of
1825 "punching through" the (Windows XP) firewall, allowing
1826 the remainder of the TFTP transfer to proceed normally.
1827 A better solution is to properly configure the firewall,
1828 but sometimes that is not allowed.
1830 - Show boot progress:
1831 CONFIG_SHOW_BOOT_PROGRESS
1833 Defining this option allows to add some board-
1834 specific code (calling a user-provided function
1835 "show_boot_progress(int)") that enables you to show
1836 the system's boot progress on some display (for
1837 example, some LED's) on your board. At the moment,
1838 the following checkpoints are implemented:
1840 - Automatic software updates via TFTP server
1842 CONFIG_UPDATE_TFTP_CNT_MAX
1843 CONFIG_UPDATE_TFTP_MSEC_MAX
1845 These options enable and control the auto-update feature;
1846 for a more detailed description refer to doc/README.update.
1848 Legacy uImage format:
1851 1 common/cmd_bootm.c before attempting to boot an image
1852 -1 common/cmd_bootm.c Image header has bad magic number
1853 2 common/cmd_bootm.c Image header has correct magic number
1854 -2 common/cmd_bootm.c Image header has bad checksum
1855 3 common/cmd_bootm.c Image header has correct checksum
1856 -3 common/cmd_bootm.c Image data has bad checksum
1857 4 common/cmd_bootm.c Image data has correct checksum
1858 -4 common/cmd_bootm.c Image is for unsupported architecture
1859 5 common/cmd_bootm.c Architecture check OK
1860 -5 common/cmd_bootm.c Wrong Image Type (not kernel, multi)
1861 6 common/cmd_bootm.c Image Type check OK
1862 -6 common/cmd_bootm.c gunzip uncompression error
1863 -7 common/cmd_bootm.c Unimplemented compression type
1864 7 common/cmd_bootm.c Uncompression OK
1865 8 common/cmd_bootm.c No uncompress/copy overwrite error
1866 -9 common/cmd_bootm.c Unsupported OS (not Linux, BSD, VxWorks, QNX)
1868 9 common/image.c Start initial ramdisk verification
1869 -10 common/image.c Ramdisk header has bad magic number
1870 -11 common/image.c Ramdisk header has bad checksum
1871 10 common/image.c Ramdisk header is OK
1872 -12 common/image.c Ramdisk data has bad checksum
1873 11 common/image.c Ramdisk data has correct checksum
1874 12 common/image.c Ramdisk verification complete, start loading
1875 -13 common/image.c Wrong Image Type (not PPC Linux ramdisk)
1876 13 common/image.c Start multifile image verification
1877 14 common/image.c No initial ramdisk, no multifile, continue.
1879 15 lib_<arch>/bootm.c All preparation done, transferring control to OS
1881 -30 lib_ppc/board.c Fatal error, hang the system
1882 -31 post/post.c POST test failed, detected by post_output_backlog()
1883 -32 post/post.c POST test failed, detected by post_run_single()
1885 34 common/cmd_doc.c before loading a Image from a DOC device
1886 -35 common/cmd_doc.c Bad usage of "doc" command
1887 35 common/cmd_doc.c correct usage of "doc" command
1888 -36 common/cmd_doc.c No boot device
1889 36 common/cmd_doc.c correct boot device
1890 -37 common/cmd_doc.c Unknown Chip ID on boot device
1891 37 common/cmd_doc.c correct chip ID found, device available
1892 -38 common/cmd_doc.c Read Error on boot device
1893 38 common/cmd_doc.c reading Image header from DOC device OK
1894 -39 common/cmd_doc.c Image header has bad magic number
1895 39 common/cmd_doc.c Image header has correct magic number
1896 -40 common/cmd_doc.c Error reading Image from DOC device
1897 40 common/cmd_doc.c Image header has correct magic number
1898 41 common/cmd_ide.c before loading a Image from a IDE device
1899 -42 common/cmd_ide.c Bad usage of "ide" command
1900 42 common/cmd_ide.c correct usage of "ide" command
1901 -43 common/cmd_ide.c No boot device
1902 43 common/cmd_ide.c boot device found
1903 -44 common/cmd_ide.c Device not available
1904 44 common/cmd_ide.c Device available
1905 -45 common/cmd_ide.c wrong partition selected
1906 45 common/cmd_ide.c partition selected
1907 -46 common/cmd_ide.c Unknown partition table
1908 46 common/cmd_ide.c valid partition table found
1909 -47 common/cmd_ide.c Invalid partition type
1910 47 common/cmd_ide.c correct partition type
1911 -48 common/cmd_ide.c Error reading Image Header on boot device
1912 48 common/cmd_ide.c reading Image Header from IDE device OK
1913 -49 common/cmd_ide.c Image header has bad magic number
1914 49 common/cmd_ide.c Image header has correct magic number
1915 -50 common/cmd_ide.c Image header has bad checksum
1916 50 common/cmd_ide.c Image header has correct checksum
1917 -51 common/cmd_ide.c Error reading Image from IDE device
1918 51 common/cmd_ide.c reading Image from IDE device OK
1919 52 common/cmd_nand.c before loading a Image from a NAND device
1920 -53 common/cmd_nand.c Bad usage of "nand" command
1921 53 common/cmd_nand.c correct usage of "nand" command
1922 -54 common/cmd_nand.c No boot device
1923 54 common/cmd_nand.c boot device found
1924 -55 common/cmd_nand.c Unknown Chip ID on boot device
1925 55 common/cmd_nand.c correct chip ID found, device available
1926 -56 common/cmd_nand.c Error reading Image Header on boot device
1927 56 common/cmd_nand.c reading Image Header from NAND device OK
1928 -57 common/cmd_nand.c Image header has bad magic number
1929 57 common/cmd_nand.c Image header has correct magic number
1930 -58 common/cmd_nand.c Error reading Image from NAND device
1931 58 common/cmd_nand.c reading Image from NAND device OK
1933 -60 common/env_common.c Environment has a bad CRC, using default
1935 64 net/eth.c starting with Ethernet configuration.
1936 -64 net/eth.c no Ethernet found.
1937 65 net/eth.c Ethernet found.
1939 -80 common/cmd_net.c usage wrong
1940 80 common/cmd_net.c before calling NetLoop()
1941 -81 common/cmd_net.c some error in NetLoop() occurred
1942 81 common/cmd_net.c NetLoop() back without error
1943 -82 common/cmd_net.c size == 0 (File with size 0 loaded)
1944 82 common/cmd_net.c trying automatic boot
1945 83 common/cmd_net.c running autoscript
1946 -83 common/cmd_net.c some error in automatic boot or autoscript
1947 84 common/cmd_net.c end without errors
1952 100 common/cmd_bootm.c Kernel FIT Image has correct format
1953 -100 common/cmd_bootm.c Kernel FIT Image has incorrect format
1954 101 common/cmd_bootm.c No Kernel subimage unit name, using configuration
1955 -101 common/cmd_bootm.c Can't get configuration for kernel subimage
1956 102 common/cmd_bootm.c Kernel unit name specified
1957 -103 common/cmd_bootm.c Can't get kernel subimage node offset
1958 103 common/cmd_bootm.c Found configuration node
1959 104 common/cmd_bootm.c Got kernel subimage node offset
1960 -104 common/cmd_bootm.c Kernel subimage hash verification failed
1961 105 common/cmd_bootm.c Kernel subimage hash verification OK
1962 -105 common/cmd_bootm.c Kernel subimage is for unsupported architecture
1963 106 common/cmd_bootm.c Architecture check OK
1964 -106 common/cmd_bootm.c Kernel subimage has wrong type
1965 107 common/cmd_bootm.c Kernel subimage type OK
1966 -107 common/cmd_bootm.c Can't get kernel subimage data/size
1967 108 common/cmd_bootm.c Got kernel subimage data/size
1968 -108 common/cmd_bootm.c Wrong image type (not legacy, FIT)
1969 -109 common/cmd_bootm.c Can't get kernel subimage type
1970 -110 common/cmd_bootm.c Can't get kernel subimage comp
1971 -111 common/cmd_bootm.c Can't get kernel subimage os
1972 -112 common/cmd_bootm.c Can't get kernel subimage load address
1973 -113 common/cmd_bootm.c Image uncompress/copy overwrite error
1975 120 common/image.c Start initial ramdisk verification
1976 -120 common/image.c Ramdisk FIT image has incorrect format
1977 121 common/image.c Ramdisk FIT image has correct format
1978 122 common/image.c No ramdisk subimage unit name, using configuration
1979 -122 common/image.c Can't get configuration for ramdisk subimage
1980 123 common/image.c Ramdisk unit name specified
1981 -124 common/image.c Can't get ramdisk subimage node offset
1982 125 common/image.c Got ramdisk subimage node offset
1983 -125 common/image.c Ramdisk subimage hash verification failed
1984 126 common/image.c Ramdisk subimage hash verification OK
1985 -126 common/image.c Ramdisk subimage for unsupported architecture
1986 127 common/image.c Architecture check OK
1987 -127 common/image.c Can't get ramdisk subimage data/size
1988 128 common/image.c Got ramdisk subimage data/size
1989 129 common/image.c Can't get ramdisk load address
1990 -129 common/image.c Got ramdisk load address
1992 -130 common/cmd_doc.c Incorrect FIT image format
1993 131 common/cmd_doc.c FIT image format OK
1995 -140 common/cmd_ide.c Incorrect FIT image format
1996 141 common/cmd_ide.c FIT image format OK
1998 -150 common/cmd_nand.c Incorrect FIT image format
1999 151 common/cmd_nand.c FIT image format OK
2005 [so far only for SMDK2400 and TRAB boards]
2007 - Modem support enable:
2008 CONFIG_MODEM_SUPPORT
2010 - RTS/CTS Flow control enable:
2013 - Modem debug support:
2014 CONFIG_MODEM_SUPPORT_DEBUG
2016 Enables debugging stuff (char screen[1024], dbg())
2017 for modem support. Useful only with BDI2000.
2019 - Interrupt support (PPC):
2021 There are common interrupt_init() and timer_interrupt()
2022 for all PPC archs. interrupt_init() calls interrupt_init_cpu()
2023 for CPU specific initialization. interrupt_init_cpu()
2024 should set decrementer_count to appropriate value. If
2025 CPU resets decrementer automatically after interrupt
2026 (ppc4xx) it should set decrementer_count to zero.
2027 timer_interrupt() calls timer_interrupt_cpu() for CPU
2028 specific handling. If board has watchdog / status_led
2029 / other_activity_monitor it works automatically from
2030 general timer_interrupt().
2034 In the target system modem support is enabled when a
2035 specific key (key combination) is pressed during
2036 power-on. Otherwise U-Boot will boot normally
2037 (autoboot). The key_pressed() function is called from
2038 board_init(). Currently key_pressed() is a dummy
2039 function, returning 1 and thus enabling modem
2042 If there are no modem init strings in the
2043 environment, U-Boot proceed to autoboot; the
2044 previous output (banner, info printfs) will be
2047 See also: doc/README.Modem
2050 Configuration Settings:
2051 -----------------------
2053 - CONFIG_SYS_LONGHELP: Defined when you want long help messages included;
2054 undefine this when you're short of memory.
2056 - CONFIG_SYS_HELP_CMD_WIDTH: Defined when you want to override the default
2057 width of the commands listed in the 'help' command output.
2059 - CONFIG_SYS_PROMPT: This is what U-Boot prints on the console to
2060 prompt for user input.
2062 - CONFIG_SYS_CBSIZE: Buffer size for input from the Console
2064 - CONFIG_SYS_PBSIZE: Buffer size for Console output
2066 - CONFIG_SYS_MAXARGS: max. Number of arguments accepted for monitor commands
2068 - CONFIG_SYS_BARGSIZE: Buffer size for Boot Arguments which are passed to
2069 the application (usually a Linux kernel) when it is
2072 - CONFIG_SYS_BAUDRATE_TABLE:
2073 List of legal baudrate settings for this board.
2075 - CONFIG_SYS_CONSOLE_INFO_QUIET
2076 Suppress display of console information at boot.
2078 - CONFIG_SYS_CONSOLE_IS_IN_ENV
2079 If the board specific function
2080 extern int overwrite_console (void);
2081 returns 1, the stdin, stderr and stdout are switched to the
2082 serial port, else the settings in the environment are used.
2084 - CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
2085 Enable the call to overwrite_console().
2087 - CONFIG_SYS_CONSOLE_ENV_OVERWRITE
2088 Enable overwrite of previous console environment settings.
2090 - CONFIG_SYS_MEMTEST_START, CONFIG_SYS_MEMTEST_END:
2091 Begin and End addresses of the area used by the
2094 - CONFIG_SYS_ALT_MEMTEST:
2095 Enable an alternate, more extensive memory test.
2097 - CONFIG_SYS_MEMTEST_SCRATCH:
2098 Scratch address used by the alternate memory test
2099 You only need to set this if address zero isn't writeable
2101 - CONFIG_SYS_MEM_TOP_HIDE (PPC only):
2102 If CONFIG_SYS_MEM_TOP_HIDE is defined in the board config header,
2103 this specified memory area will get subtracted from the top
2104 (end) of RAM and won't get "touched" at all by U-Boot. By
2105 fixing up gd->ram_size the Linux kernel should gets passed
2106 the now "corrected" memory size and won't touch it either.
2107 This should work for arch/ppc and arch/powerpc. Only Linux
2108 board ports in arch/powerpc with bootwrapper support that
2109 recalculate the memory size from the SDRAM controller setup
2110 will have to get fixed in Linux additionally.
2112 This option can be used as a workaround for the 440EPx/GRx
2113 CHIP 11 errata where the last 256 bytes in SDRAM shouldn't
2116 WARNING: Please make sure that this value is a multiple of
2117 the Linux page size (normally 4k). If this is not the case,
2118 then the end address of the Linux memory will be located at a
2119 non page size aligned address and this could cause major
2122 - CONFIG_SYS_TFTP_LOADADDR:
2123 Default load address for network file downloads
2125 - CONFIG_SYS_LOADS_BAUD_CHANGE:
2126 Enable temporary baudrate change while serial download
2128 - CONFIG_SYS_SDRAM_BASE:
2129 Physical start address of SDRAM. _Must_ be 0 here.
2131 - CONFIG_SYS_MBIO_BASE:
2132 Physical start address of Motherboard I/O (if using a
2135 - CONFIG_SYS_FLASH_BASE:
2136 Physical start address of Flash memory.
2138 - CONFIG_SYS_MONITOR_BASE:
2139 Physical start address of boot monitor code (set by
2140 make config files to be same as the text base address
2141 (TEXT_BASE) used when linking) - same as
2142 CONFIG_SYS_FLASH_BASE when booting from flash.
2144 - CONFIG_SYS_MONITOR_LEN:
2145 Size of memory reserved for monitor code, used to
2146 determine _at_compile_time_ (!) if the environment is
2147 embedded within the U-Boot image, or in a separate
2150 - CONFIG_SYS_MALLOC_LEN:
2151 Size of DRAM reserved for malloc() use.
2153 - CONFIG_SYS_BOOTM_LEN:
2154 Normally compressed uImages are limited to an
2155 uncompressed size of 8 MBytes. If this is not enough,
2156 you can define CONFIG_SYS_BOOTM_LEN in your board config file
2157 to adjust this setting to your needs.
2159 - CONFIG_SYS_BOOTMAPSZ:
2160 Maximum size of memory mapped by the startup code of
2161 the Linux kernel; all data that must be processed by
2162 the Linux kernel (bd_info, boot arguments, FDT blob if
2163 used) must be put below this limit, unless "bootm_low"
2164 enviroment variable is defined and non-zero. In such case
2165 all data for the Linux kernel must be between "bootm_low"
2166 and "bootm_low" + CONFIG_SYS_BOOTMAPSZ.
2168 - CONFIG_SYS_MAX_FLASH_BANKS:
2169 Max number of Flash memory banks
2171 - CONFIG_SYS_MAX_FLASH_SECT:
2172 Max number of sectors on a Flash chip
2174 - CONFIG_SYS_FLASH_ERASE_TOUT:
2175 Timeout for Flash erase operations (in ms)
2177 - CONFIG_SYS_FLASH_WRITE_TOUT:
2178 Timeout for Flash write operations (in ms)
2180 - CONFIG_SYS_FLASH_LOCK_TOUT
2181 Timeout for Flash set sector lock bit operation (in ms)
2183 - CONFIG_SYS_FLASH_UNLOCK_TOUT
2184 Timeout for Flash clear lock bits operation (in ms)
2186 - CONFIG_SYS_FLASH_PROTECTION
2187 If defined, hardware flash sectors protection is used
2188 instead of U-Boot software protection.
2190 - CONFIG_SYS_DIRECT_FLASH_TFTP:
2192 Enable TFTP transfers directly to flash memory;
2193 without this option such a download has to be
2194 performed in two steps: (1) download to RAM, and (2)
2195 copy from RAM to flash.
2197 The two-step approach is usually more reliable, since
2198 you can check if the download worked before you erase
2199 the flash, but in some situations (when system RAM is
2200 too limited to allow for a temporary copy of the
2201 downloaded image) this option may be very useful.
2203 - CONFIG_SYS_FLASH_CFI:
2204 Define if the flash driver uses extra elements in the
2205 common flash structure for storing flash geometry.
2207 - CONFIG_FLASH_CFI_DRIVER
2208 This option also enables the building of the cfi_flash driver
2209 in the drivers directory
2211 - CONFIG_FLASH_CFI_MTD
2212 This option enables the building of the cfi_mtd driver
2213 in the drivers directory. The driver exports CFI flash
2216 - CONFIG_SYS_FLASH_USE_BUFFER_WRITE
2217 Use buffered writes to flash.
2219 - CONFIG_FLASH_SPANSION_S29WS_N
2220 s29ws-n MirrorBit flash has non-standard addresses for buffered
2223 - CONFIG_SYS_FLASH_QUIET_TEST
2224 If this option is defined, the common CFI flash doesn't
2225 print it's warning upon not recognized FLASH banks. This
2226 is useful, if some of the configured banks are only
2227 optionally available.
2229 - CONFIG_FLASH_SHOW_PROGRESS
2230 If defined (must be an integer), print out countdown
2231 digits and dots. Recommended value: 45 (9..1) for 80
2232 column displays, 15 (3..1) for 40 column displays.
2234 - CONFIG_SYS_RX_ETH_BUFFER:
2235 Defines the number of Ethernet receive buffers. On some
2236 Ethernet controllers it is recommended to set this value
2237 to 8 or even higher (EEPRO100 or 405 EMAC), since all
2238 buffers can be full shortly after enabling the interface
2239 on high Ethernet traffic.
2240 Defaults to 4 if not defined.
2242 The following definitions that deal with the placement and management
2243 of environment data (variable area); in general, we support the
2244 following configurations:
2246 - CONFIG_ENV_IS_IN_FLASH:
2248 Define this if the environment is in flash memory.
2250 a) The environment occupies one whole flash sector, which is
2251 "embedded" in the text segment with the U-Boot code. This
2252 happens usually with "bottom boot sector" or "top boot
2253 sector" type flash chips, which have several smaller
2254 sectors at the start or the end. For instance, such a
2255 layout can have sector sizes of 8, 2x4, 16, Nx32 kB. In
2256 such a case you would place the environment in one of the
2257 4 kB sectors - with U-Boot code before and after it. With
2258 "top boot sector" type flash chips, you would put the
2259 environment in one of the last sectors, leaving a gap
2260 between U-Boot and the environment.
2262 - CONFIG_ENV_OFFSET:
2264 Offset of environment data (variable area) to the
2265 beginning of flash memory; for instance, with bottom boot
2266 type flash chips the second sector can be used: the offset
2267 for this sector is given here.
2269 CONFIG_ENV_OFFSET is used relative to CONFIG_SYS_FLASH_BASE.
2273 This is just another way to specify the start address of
2274 the flash sector containing the environment (instead of
2277 - CONFIG_ENV_SECT_SIZE:
2279 Size of the sector containing the environment.
2282 b) Sometimes flash chips have few, equal sized, BIG sectors.
2283 In such a case you don't want to spend a whole sector for
2288 If you use this in combination with CONFIG_ENV_IS_IN_FLASH
2289 and CONFIG_ENV_SECT_SIZE, you can specify to use only a part
2290 of this flash sector for the environment. This saves
2291 memory for the RAM copy of the environment.
2293 It may also save flash memory if you decide to use this
2294 when your environment is "embedded" within U-Boot code,
2295 since then the remainder of the flash sector could be used
2296 for U-Boot code. It should be pointed out that this is
2297 STRONGLY DISCOURAGED from a robustness point of view:
2298 updating the environment in flash makes it always
2299 necessary to erase the WHOLE sector. If something goes
2300 wrong before the contents has been restored from a copy in
2301 RAM, your target system will be dead.
2303 - CONFIG_ENV_ADDR_REDUND
2304 CONFIG_ENV_SIZE_REDUND
2306 These settings describe a second storage area used to hold
2307 a redundant copy of the environment data, so that there is
2308 a valid backup copy in case there is a power failure during
2309 a "saveenv" operation.
2311 BE CAREFUL! Any changes to the flash layout, and some changes to the
2312 source code will make it necessary to adapt <board>/u-boot.lds*
2316 - CONFIG_ENV_IS_IN_NVRAM:
2318 Define this if you have some non-volatile memory device
2319 (NVRAM, battery buffered SRAM) which you want to use for the
2325 These two #defines are used to determine the memory area you
2326 want to use for environment. It is assumed that this memory
2327 can just be read and written to, without any special
2330 BE CAREFUL! The first access to the environment happens quite early
2331 in U-Boot initalization (when we try to get the setting of for the
2332 console baudrate). You *MUST* have mapped your NVRAM area then, or
2335 Please note that even with NVRAM we still use a copy of the
2336 environment in RAM: we could work on NVRAM directly, but we want to
2337 keep settings there always unmodified except somebody uses "saveenv"
2338 to save the current settings.
2341 - CONFIG_ENV_IS_IN_EEPROM:
2343 Use this if you have an EEPROM or similar serial access
2344 device and a driver for it.
2346 - CONFIG_ENV_OFFSET:
2349 These two #defines specify the offset and size of the
2350 environment area within the total memory of your EEPROM.
2352 - CONFIG_SYS_I2C_EEPROM_ADDR:
2353 If defined, specified the chip address of the EEPROM device.
2354 The default address is zero.
2356 - CONFIG_SYS_EEPROM_PAGE_WRITE_BITS:
2357 If defined, the number of bits used to address bytes in a
2358 single page in the EEPROM device. A 64 byte page, for example
2359 would require six bits.
2361 - CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS:
2362 If defined, the number of milliseconds to delay between
2363 page writes. The default is zero milliseconds.
2365 - CONFIG_SYS_I2C_EEPROM_ADDR_LEN:
2366 The length in bytes of the EEPROM memory array address. Note
2367 that this is NOT the chip address length!
2369 - CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW:
2370 EEPROM chips that implement "address overflow" are ones
2371 like Catalyst 24WC04/08/16 which has 9/10/11 bits of
2372 address and the extra bits end up in the "chip address" bit
2373 slots. This makes a 24WC08 (1Kbyte) chip look like four 256
2376 Note that we consider the length of the address field to
2377 still be one byte because the extra address bits are hidden
2378 in the chip address.
2380 - CONFIG_SYS_EEPROM_SIZE:
2381 The size in bytes of the EEPROM device.
2384 - CONFIG_ENV_IS_IN_DATAFLASH:
2386 Define this if you have a DataFlash memory device which you
2387 want to use for the environment.
2389 - CONFIG_ENV_OFFSET:
2393 These three #defines specify the offset and size of the
2394 environment area within the total memory of your DataFlash placed
2395 at the specified address.
2397 - CONFIG_ENV_IS_IN_NAND:
2399 Define this if you have a NAND device which you want to use
2400 for the environment.
2402 - CONFIG_ENV_OFFSET:
2405 These two #defines specify the offset and size of the environment
2406 area within the first NAND device.
2408 - CONFIG_ENV_OFFSET_REDUND
2410 This setting describes a second storage area of CONFIG_ENV_SIZE
2411 size used to hold a redundant copy of the environment data,
2412 so that there is a valid backup copy in case there is a
2413 power failure during a "saveenv" operation.
2415 Note: CONFIG_ENV_OFFSET and CONFIG_ENV_OFFSET_REDUND must be aligned
2416 to a block boundary, and CONFIG_ENV_SIZE must be a multiple of
2417 the NAND devices block size.
2419 - CONFIG_SYS_SPI_INIT_OFFSET
2421 Defines offset to the initial SPI buffer area in DPRAM. The
2422 area is used at an early stage (ROM part) if the environment
2423 is configured to reside in the SPI EEPROM: We need a 520 byte
2424 scratch DPRAM area. It is used between the two initialization
2425 calls (spi_init_f() and spi_init_r()). A value of 0xB00 seems
2426 to be a good choice since it makes it far enough from the
2427 start of the data area as well as from the stack pointer.
2429 Please note that the environment is read-only until the monitor
2430 has been relocated to RAM and a RAM copy of the environment has been
2431 created; also, when using EEPROM you will have to use getenv_r()
2432 until then to read environment variables.
2434 The environment is protected by a CRC32 checksum. Before the monitor
2435 is relocated into RAM, as a result of a bad CRC you will be working
2436 with the compiled-in default environment - *silently*!!! [This is
2437 necessary, because the first environment variable we need is the
2438 "baudrate" setting for the console - if we have a bad CRC, we don't
2439 have any device yet where we could complain.]
2441 Note: once the monitor has been relocated, then it will complain if
2442 the default environment is used; a new CRC is computed as soon as you
2443 use the "saveenv" command to store a valid environment.
2445 - CONFIG_SYS_FAULT_ECHO_LINK_DOWN:
2446 Echo the inverted Ethernet link state to the fault LED.
2448 Note: If this option is active, then CONFIG_SYS_FAULT_MII_ADDR
2449 also needs to be defined.
2451 - CONFIG_SYS_FAULT_MII_ADDR:
2452 MII address of the PHY to check for the Ethernet link state.
2454 - CONFIG_SYS_64BIT_VSPRINTF:
2455 Makes vsprintf (and all *printf functions) support printing
2456 of 64bit values by using the L quantifier
2458 - CONFIG_SYS_64BIT_STRTOUL:
2459 Adds simple_strtoull that returns a 64bit value
2461 - CONFIG_NS16550_MIN_FUNCTIONS:
2462 Define this if you desire to only have use of the NS16550_init
2463 and NS16550_putc functions for the serial driver located at
2464 drivers/serial/ns16550.c. This option is useful for saving
2465 space for already greatly restricted images, including but not
2466 limited to NAND_SPL configurations.
2468 Low Level (hardware related) configuration options:
2469 ---------------------------------------------------
2471 - CONFIG_SYS_CACHELINE_SIZE:
2472 Cache Line Size of the CPU.
2474 - CONFIG_SYS_DEFAULT_IMMR:
2475 Default address of the IMMR after system reset.
2477 Needed on some 8260 systems (MPC8260ADS, PQ2FADS-ZU,
2478 and RPXsuper) to be able to adjust the position of
2479 the IMMR register after a reset.
2481 - Floppy Disk Support:
2482 CONFIG_SYS_FDC_DRIVE_NUMBER
2484 the default drive number (default value 0)
2486 CONFIG_SYS_ISA_IO_STRIDE
2488 defines the spacing between FDC chipset registers
2491 CONFIG_SYS_ISA_IO_OFFSET
2493 defines the offset of register from address. It
2494 depends on which part of the data bus is connected to
2495 the FDC chipset. (default value 0)
2497 If CONFIG_SYS_ISA_IO_STRIDE CONFIG_SYS_ISA_IO_OFFSET and
2498 CONFIG_SYS_FDC_DRIVE_NUMBER are undefined, they take their
2501 if CONFIG_SYS_FDC_HW_INIT is defined, then the function
2502 fdc_hw_init() is called at the beginning of the FDC
2503 setup. fdc_hw_init() must be provided by the board
2504 source code. It is used to make hardware dependant
2507 - CONFIG_SYS_IMMR: Physical address of the Internal Memory.
2508 DO NOT CHANGE unless you know exactly what you're
2509 doing! (11-4) [MPC8xx/82xx systems only]
2511 - CONFIG_SYS_INIT_RAM_ADDR:
2513 Start address of memory area that can be used for
2514 initial data and stack; please note that this must be
2515 writable memory that is working WITHOUT special
2516 initialization, i. e. you CANNOT use normal RAM which
2517 will become available only after programming the
2518 memory controller and running certain initialization
2521 U-Boot uses the following memory types:
2522 - MPC8xx and MPC8260: IMMR (internal memory of the CPU)
2523 - MPC824X: data cache
2524 - PPC4xx: data cache
2526 - CONFIG_SYS_GBL_DATA_OFFSET:
2528 Offset of the initial data structure in the memory
2529 area defined by CONFIG_SYS_INIT_RAM_ADDR. Usually
2530 CONFIG_SYS_GBL_DATA_OFFSET is chosen such that the initial
2531 data is located at the end of the available space
2532 (sometimes written as (CONFIG_SYS_INIT_RAM_END -
2533 CONFIG_SYS_INIT_DATA_SIZE), and the initial stack is just
2534 below that area (growing from (CONFIG_SYS_INIT_RAM_ADDR +
2535 CONFIG_SYS_GBL_DATA_OFFSET) downward.
2538 On the MPC824X (or other systems that use the data
2539 cache for initial memory) the address chosen for
2540 CONFIG_SYS_INIT_RAM_ADDR is basically arbitrary - it must
2541 point to an otherwise UNUSED address space between
2542 the top of RAM and the start of the PCI space.
2544 - CONFIG_SYS_SIUMCR: SIU Module Configuration (11-6)
2546 - CONFIG_SYS_SYPCR: System Protection Control (11-9)
2548 - CONFIG_SYS_TBSCR: Time Base Status and Control (11-26)
2550 - CONFIG_SYS_PISCR: Periodic Interrupt Status and Control (11-31)
2552 - CONFIG_SYS_PLPRCR: PLL, Low-Power, and Reset Control Register (15-30)
2554 - CONFIG_SYS_SCCR: System Clock and reset Control Register (15-27)
2556 - CONFIG_SYS_OR_TIMING_SDRAM:
2559 - CONFIG_SYS_MAMR_PTA:
2560 periodic timer for refresh
2562 - CONFIG_SYS_DER: Debug Event Register (37-47)
2564 - FLASH_BASE0_PRELIM, FLASH_BASE1_PRELIM, CONFIG_SYS_REMAP_OR_AM,
2565 CONFIG_SYS_PRELIM_OR_AM, CONFIG_SYS_OR_TIMING_FLASH, CONFIG_SYS_OR0_REMAP,
2566 CONFIG_SYS_OR0_PRELIM, CONFIG_SYS_BR0_PRELIM, CONFIG_SYS_OR1_REMAP, CONFIG_SYS_OR1_PRELIM,
2567 CONFIG_SYS_BR1_PRELIM:
2568 Memory Controller Definitions: BR0/1 and OR0/1 (FLASH)
2570 - SDRAM_BASE2_PRELIM, SDRAM_BASE3_PRELIM, SDRAM_MAX_SIZE,
2571 CONFIG_SYS_OR_TIMING_SDRAM, CONFIG_SYS_OR2_PRELIM, CONFIG_SYS_BR2_PRELIM,
2572 CONFIG_SYS_OR3_PRELIM, CONFIG_SYS_BR3_PRELIM:
2573 Memory Controller Definitions: BR2/3 and OR2/3 (SDRAM)
2575 - CONFIG_SYS_MAMR_PTA, CONFIG_SYS_MPTPR_2BK_4K, CONFIG_SYS_MPTPR_1BK_4K, CONFIG_SYS_MPTPR_2BK_8K,
2576 CONFIG_SYS_MPTPR_1BK_8K, CONFIG_SYS_MAMR_8COL, CONFIG_SYS_MAMR_9COL:
2577 Machine Mode Register and Memory Periodic Timer
2578 Prescaler definitions (SDRAM timing)
2580 - CONFIG_SYS_I2C_UCODE_PATCH, CONFIG_SYS_I2C_DPMEM_OFFSET [0x1FC0]:
2581 enable I2C microcode relocation patch (MPC8xx);
2582 define relocation offset in DPRAM [DSP2]
2584 - CONFIG_SYS_SMC_UCODE_PATCH, CONFIG_SYS_SMC_DPMEM_OFFSET [0x1FC0]:
2585 enable SMC microcode relocation patch (MPC8xx);
2586 define relocation offset in DPRAM [SMC1]
2588 - CONFIG_SYS_SPI_UCODE_PATCH, CONFIG_SYS_SPI_DPMEM_OFFSET [0x1FC0]:
2589 enable SPI microcode relocation patch (MPC8xx);
2590 define relocation offset in DPRAM [SCC4]
2592 - CONFIG_SYS_USE_OSCCLK:
2593 Use OSCM clock mode on MBX8xx board. Be careful,
2594 wrong setting might damage your board. Read
2595 doc/README.MBX before setting this variable!
2597 - CONFIG_SYS_CPM_POST_WORD_ADDR: (MPC8xx, MPC8260 only)
2598 Offset of the bootmode word in DPRAM used by post
2599 (Power On Self Tests). This definition overrides
2600 #define'd default value in commproc.h resp.
2603 - CONFIG_SYS_PCI_SLV_MEM_LOCAL, CONFIG_SYS_PCI_SLV_MEM_BUS, CONFIG_SYS_PICMR0_MASK_ATTRIB,
2604 CONFIG_SYS_PCI_MSTR0_LOCAL, CONFIG_SYS_PCIMSK0_MASK, CONFIG_SYS_PCI_MSTR1_LOCAL,
2605 CONFIG_SYS_PCIMSK1_MASK, CONFIG_SYS_PCI_MSTR_MEM_LOCAL, CONFIG_SYS_PCI_MSTR_MEM_BUS,
2606 CONFIG_SYS_CPU_PCI_MEM_START, CONFIG_SYS_PCI_MSTR_MEM_SIZE, CONFIG_SYS_POCMR0_MASK_ATTRIB,
2607 CONFIG_SYS_PCI_MSTR_MEMIO_LOCAL, CONFIG_SYS_PCI_MSTR_MEMIO_BUS, CPU_PCI_MEMIO_START,
2608 CONFIG_SYS_PCI_MSTR_MEMIO_SIZE, CONFIG_SYS_POCMR1_MASK_ATTRIB, CONFIG_SYS_PCI_MSTR_IO_LOCAL,
2609 CONFIG_SYS_PCI_MSTR_IO_BUS, CONFIG_SYS_CPU_PCI_IO_START, CONFIG_SYS_PCI_MSTR_IO_SIZE,
2610 CONFIG_SYS_POCMR2_MASK_ATTRIB: (MPC826x only)
2611 Overrides the default PCI memory map in cpu/mpc8260/pci.c if set.
2613 - CONFIG_PCI_DISABLE_PCIE:
2614 Disable PCI-Express on systems where it is supported but not
2618 Get DDR timing information from an I2C EEPROM. Common
2619 with pluggable memory modules such as SODIMMs
2622 I2C address of the SPD EEPROM
2624 - CONFIG_SYS_SPD_BUS_NUM
2625 If SPD EEPROM is on an I2C bus other than the first
2626 one, specify here. Note that the value must resolve
2627 to something your driver can deal with.
2629 - CONFIG_SYS_83XX_DDR_USES_CS0
2630 Only for 83xx systems. If specified, then DDR should
2631 be configured using CS0 and CS1 instead of CS2 and CS3.
2633 - CONFIG_SYS_83XX_DDR_USES_CS0
2634 Only for 83xx systems. If specified, then DDR should
2635 be configured using CS0 and CS1 instead of CS2 and CS3.
2637 - CONFIG_ETHER_ON_FEC[12]
2638 Define to enable FEC[12] on a 8xx series processor.
2640 - CONFIG_FEC[12]_PHY
2641 Define to the hardcoded PHY address which corresponds
2642 to the given FEC; i. e.
2643 #define CONFIG_FEC1_PHY 4
2644 means that the PHY with address 4 is connected to FEC1
2646 When set to -1, means to probe for first available.
2648 - CONFIG_FEC[12]_PHY_NORXERR
2649 The PHY does not have a RXERR line (RMII only).
2650 (so program the FEC to ignore it).
2653 Enable RMII mode for all FECs.
2654 Note that this is a global option, we can't
2655 have one FEC in standard MII mode and another in RMII mode.
2657 - CONFIG_CRC32_VERIFY
2658 Add a verify option to the crc32 command.
2661 => crc32 -v <address> <count> <crc32>
2663 Where address/count indicate a memory area
2664 and crc32 is the correct crc32 which the
2668 Add the "loopw" memory command. This only takes effect if
2669 the memory commands are activated globally (CONFIG_CMD_MEM).
2672 Add the "mdc" and "mwc" memory commands. These are cyclic
2677 This command will print 4 bytes (10,11,12,13) each 500 ms.
2679 => mwc.l 100 12345678 10
2680 This command will write 12345678 to address 100 all 10 ms.
2682 This only takes effect if the memory commands are activated
2683 globally (CONFIG_CMD_MEM).
2685 - CONFIG_SKIP_LOWLEVEL_INIT
2686 - CONFIG_SKIP_RELOCATE_UBOOT
2688 [ARM only] If these variables are defined, then
2689 certain low level initializations (like setting up
2690 the memory controller) are omitted and/or U-Boot does
2691 not relocate itself into RAM.
2692 Normally these variables MUST NOT be defined. The
2693 only exception is when U-Boot is loaded (to RAM) by
2694 some other boot loader or by a debugger which
2695 performs these initializations itself.
2698 Building the Software:
2699 ======================
2701 Building U-Boot has been tested in several native build environments
2702 and in many different cross environments. Of course we cannot support
2703 all possibly existing versions of cross development tools in all
2704 (potentially obsolete) versions. In case of tool chain problems we
2705 recommend to use the ELDK (see http://www.denx.de/wiki/DULG/ELDK)
2706 which is extensively used to build and test U-Boot.
2708 If you are not using a native environment, it is assumed that you
2709 have GNU cross compiling tools available in your path. In this case,
2710 you must set the environment variable CROSS_COMPILE in your shell.
2711 Note that no changes to the Makefile or any other source files are
2712 necessary. For example using the ELDK on a 4xx CPU, please enter:
2714 $ CROSS_COMPILE=ppc_4xx-
2715 $ export CROSS_COMPILE
2717 U-Boot is intended to be simple to build. After installing the
2718 sources you must configure U-Boot for one specific board type. This
2723 where "NAME_config" is the name of one of the existing configu-
2724 rations; see the main Makefile for supported names.
2726 Note: for some board special configuration names may exist; check if
2727 additional information is available from the board vendor; for
2728 instance, the TQM823L systems are available without (standard)
2729 or with LCD support. You can select such additional "features"
2730 when choosing the configuration, i. e.
2733 - will configure for a plain TQM823L, i. e. no LCD support
2735 make TQM823L_LCD_config
2736 - will configure for a TQM823L with U-Boot console on LCD
2741 Finally, type "make all", and you should get some working U-Boot
2742 images ready for download to / installation on your system:
2744 - "u-boot.bin" is a raw binary image
2745 - "u-boot" is an image in ELF binary format
2746 - "u-boot.srec" is in Motorola S-Record format
2748 By default the build is performed locally and the objects are saved
2749 in the source directory. One of the two methods can be used to change
2750 this behavior and build U-Boot to some external directory:
2752 1. Add O= to the make command line invocations:
2754 make O=/tmp/build distclean
2755 make O=/tmp/build NAME_config
2756 make O=/tmp/build all
2758 2. Set environment variable BUILD_DIR to point to the desired location:
2760 export BUILD_DIR=/tmp/build
2765 Note that the command line "O=" setting overrides the BUILD_DIR environment
2769 Please be aware that the Makefiles assume you are using GNU make, so
2770 for instance on NetBSD you might need to use "gmake" instead of
2774 If the system board that you have is not listed, then you will need
2775 to port U-Boot to your hardware platform. To do this, follow these
2778 1. Add a new configuration option for your board to the toplevel
2779 "Makefile" and to the "MAKEALL" script, using the existing
2780 entries as examples. Note that here and at many other places
2781 boards and other names are listed in alphabetical sort order. Please
2783 2. Create a new directory to hold your board specific code. Add any
2784 files you need. In your board directory, you will need at least
2785 the "Makefile", a "<board>.c", "flash.c" and "u-boot.lds".
2786 3. Create a new configuration file "include/configs/<board>.h" for
2788 3. If you're porting U-Boot to a new CPU, then also create a new
2789 directory to hold your CPU specific code. Add any files you need.
2790 4. Run "make <board>_config" with your new name.
2791 5. Type "make", and you should get a working "u-boot.srec" file
2792 to be installed on your target system.
2793 6. Debug and solve any problems that might arise.
2794 [Of course, this last step is much harder than it sounds.]
2797 Testing of U-Boot Modifications, Ports to New Hardware, etc.:
2798 ==============================================================
2800 If you have modified U-Boot sources (for instance added a new board
2801 or support for new devices, a new CPU, etc.) you are expected to
2802 provide feedback to the other developers. The feedback normally takes
2803 the form of a "patch", i. e. a context diff against a certain (latest
2804 official or latest in the git repository) version of U-Boot sources.
2806 But before you submit such a patch, please verify that your modifi-
2807 cation did not break existing code. At least make sure that *ALL* of
2808 the supported boards compile WITHOUT ANY compiler warnings. To do so,
2809 just run the "MAKEALL" script, which will configure and build U-Boot
2810 for ALL supported system. Be warned, this will take a while. You can
2811 select which (cross) compiler to use by passing a `CROSS_COMPILE'
2812 environment variable to the script, i. e. to use the ELDK cross tools
2815 CROSS_COMPILE=ppc_8xx- MAKEALL
2817 or to build on a native PowerPC system you can type
2819 CROSS_COMPILE=' ' MAKEALL
2821 When using the MAKEALL script, the default behaviour is to build
2822 U-Boot in the source directory. This location can be changed by
2823 setting the BUILD_DIR environment variable. Also, for each target
2824 built, the MAKEALL script saves two log files (<target>.ERR and
2825 <target>.MAKEALL) in the <source dir>/LOG directory. This default
2826 location can be changed by setting the MAKEALL_LOGDIR environment
2827 variable. For example:
2829 export BUILD_DIR=/tmp/build
2830 export MAKEALL_LOGDIR=/tmp/log
2831 CROSS_COMPILE=ppc_8xx- MAKEALL
2833 With the above settings build objects are saved in the /tmp/build,
2834 log files are saved in the /tmp/log and the source tree remains clean
2835 during the whole build process.
2838 See also "U-Boot Porting Guide" below.
2841 Monitor Commands - Overview:
2842 ============================
2844 go - start application at address 'addr'
2845 run - run commands in an environment variable
2846 bootm - boot application image from memory
2847 bootp - boot image via network using BootP/TFTP protocol
2848 tftpboot- boot image via network using TFTP protocol
2849 and env variables "ipaddr" and "serverip"
2850 (and eventually "gatewayip")
2851 rarpboot- boot image via network using RARP/TFTP protocol
2852 diskboot- boot from IDE devicebootd - boot default, i.e., run 'bootcmd'
2853 loads - load S-Record file over serial line
2854 loadb - load binary file over serial line (kermit mode)
2856 mm - memory modify (auto-incrementing)
2857 nm - memory modify (constant address)
2858 mw - memory write (fill)
2860 cmp - memory compare
2861 crc32 - checksum calculation
2862 imd - i2c memory display
2863 imm - i2c memory modify (auto-incrementing)
2864 inm - i2c memory modify (constant address)
2865 imw - i2c memory write (fill)
2866 icrc32 - i2c checksum calculation
2867 iprobe - probe to discover valid I2C chip addresses
2868 iloop - infinite loop on address range
2869 isdram - print SDRAM configuration information
2870 sspi - SPI utility commands
2871 base - print or set address offset
2872 printenv- print environment variables
2873 setenv - set environment variables
2874 saveenv - save environment variables to persistent storage
2875 protect - enable or disable FLASH write protection
2876 erase - erase FLASH memory
2877 flinfo - print FLASH memory information
2878 bdinfo - print Board Info structure
2879 iminfo - print header information for application image
2880 coninfo - print console devices and informations
2881 ide - IDE sub-system
2882 loop - infinite loop on address range
2883 loopw - infinite write loop on address range
2884 mtest - simple RAM test
2885 icache - enable or disable instruction cache
2886 dcache - enable or disable data cache
2887 reset - Perform RESET of the CPU
2888 echo - echo args to console
2889 version - print monitor version
2890 help - print online help
2891 ? - alias for 'help'
2894 Monitor Commands - Detailed Description:
2895 ========================================
2899 For now: just type "help <command>".
2902 Environment Variables:
2903 ======================
2905 U-Boot supports user configuration using Environment Variables which
2906 can be made persistent by saving to Flash memory.
2908 Environment Variables are set using "setenv", printed using
2909 "printenv", and saved to Flash using "saveenv". Using "setenv"
2910 without a value can be used to delete a variable from the
2911 environment. As long as you don't save the environment you are
2912 working with an in-memory copy. In case the Flash area containing the
2913 environment is erased by accident, a default environment is provided.
2915 Some configuration options can be set using Environment Variables:
2917 baudrate - see CONFIG_BAUDRATE
2919 bootdelay - see CONFIG_BOOTDELAY
2921 bootcmd - see CONFIG_BOOTCOMMAND
2923 bootargs - Boot arguments when booting an RTOS image
2925 bootfile - Name of the image to load with TFTP
2927 bootm_low - Memory range available for image processing in the bootm
2928 command can be restricted. This variable is given as
2929 a hexadecimal number and defines lowest address allowed
2930 for use by the bootm command. See also "bootm_size"
2931 environment variable. Address defined by "bootm_low" is
2932 also the base of the initial memory mapping for the Linux
2933 kernel -- see the description of CONFIG_SYS_BOOTMAPSZ.
2935 bootm_size - Memory range available for image processing in the bootm
2936 command can be restricted. This variable is given as
2937 a hexadecimal number and defines the size of the region
2938 allowed for use by the bootm command. See also "bootm_low"
2939 environment variable.
2941 updatefile - Location of the software update file on a TFTP server, used
2942 by the automatic software update feature. Please refer to
2943 documentation in doc/README.update for more details.
2945 autoload - if set to "no" (any string beginning with 'n'),
2946 "bootp" will just load perform a lookup of the
2947 configuration from the BOOTP server, but not try to
2948 load any image using TFTP
2950 autoscript - if set to "yes" commands like "loadb", "loady",
2951 "bootp", "tftpb", "rarpboot" and "nfs" will attempt
2952 to automatically run script images (by internally
2953 calling "autoscript").
2955 autoscript_uname - if script image is in a format (FIT) this
2956 variable is used to get script subimage unit name.
2958 autostart - if set to "yes", an image loaded using the "bootp",
2959 "rarpboot", "tftpboot" or "diskboot" commands will
2960 be automatically started (by internally calling
2963 If set to "no", a standalone image passed to the
2964 "bootm" command will be copied to the load address
2965 (and eventually uncompressed), but NOT be started.
2966 This can be used to load and uncompress arbitrary
2969 i2cfast - (PPC405GP|PPC405EP only)
2970 if set to 'y' configures Linux I2C driver for fast
2971 mode (400kHZ). This environment variable is used in
2972 initialization code. So, for changes to be effective
2973 it must be saved and board must be reset.
2975 initrd_high - restrict positioning of initrd images:
2976 If this variable is not set, initrd images will be
2977 copied to the highest possible address in RAM; this
2978 is usually what you want since it allows for
2979 maximum initrd size. If for some reason you want to
2980 make sure that the initrd image is loaded below the
2981 CONFIG_SYS_BOOTMAPSZ limit, you can set this environment
2982 variable to a value of "no" or "off" or "0".
2983 Alternatively, you can set it to a maximum upper
2984 address to use (U-Boot will still check that it
2985 does not overwrite the U-Boot stack and data).
2987 For instance, when you have a system with 16 MB
2988 RAM, and want to reserve 4 MB from use by Linux,
2989 you can do this by adding "mem=12M" to the value of
2990 the "bootargs" variable. However, now you must make
2991 sure that the initrd image is placed in the first
2992 12 MB as well - this can be done with
2994 setenv initrd_high 00c00000
2996 If you set initrd_high to 0xFFFFFFFF, this is an
2997 indication to U-Boot that all addresses are legal
2998 for the Linux kernel, including addresses in flash
2999 memory. In this case U-Boot will NOT COPY the
3000 ramdisk at all. This may be useful to reduce the
3001 boot time on your system, but requires that this
3002 feature is supported by your Linux kernel.
3004 ipaddr - IP address; needed for tftpboot command
3006 loadaddr - Default load address for commands like "bootp",
3007 "rarpboot", "tftpboot", "loadb" or "diskboot"
3009 loads_echo - see CONFIG_LOADS_ECHO
3011 serverip - TFTP server IP address; needed for tftpboot command
3013 bootretry - see CONFIG_BOOT_RETRY_TIME
3015 bootdelaykey - see CONFIG_AUTOBOOT_DELAY_STR
3017 bootstopkey - see CONFIG_AUTOBOOT_STOP_STR
3019 ethprime - When CONFIG_NET_MULTI is enabled controls which
3020 interface is used first.
3022 ethact - When CONFIG_NET_MULTI is enabled controls which
3023 interface is currently active. For example you
3024 can do the following
3026 => setenv ethact FEC ETHERNET
3027 => ping 192.168.0.1 # traffic sent on FEC ETHERNET
3028 => setenv ethact SCC ETHERNET
3029 => ping 10.0.0.1 # traffic sent on SCC ETHERNET
3031 ethrotate - When set to "no" U-Boot does not go through all
3032 available network interfaces.
3033 It just stays at the currently selected interface.
3035 netretry - When set to "no" each network operation will
3036 either succeed or fail without retrying.
3037 When set to "once" the network operation will
3038 fail when all the available network interfaces
3039 are tried once without success.
3040 Useful on scripts which control the retry operation
3043 npe_ucode - set load address for the NPE microcode
3045 tftpsrcport - If this is set, the value is used for TFTP's
3048 tftpdstport - If this is set, the value is used for TFTP's UDP
3049 destination port instead of the Well Know Port 69.
3051 vlan - When set to a value < 4095 the traffic over
3052 Ethernet is encapsulated/received over 802.1q
3055 The following environment variables may be used and automatically
3056 updated by the network boot commands ("bootp" and "rarpboot"),
3057 depending the information provided by your boot server:
3059 bootfile - see above
3060 dnsip - IP address of your Domain Name Server
3061 dnsip2 - IP address of your secondary Domain Name Server
3062 gatewayip - IP address of the Gateway (Router) to use
3063 hostname - Target hostname
3065 netmask - Subnet Mask
3066 rootpath - Pathname of the root filesystem on the NFS server
3067 serverip - see above
3070 There are two special Environment Variables:
3072 serial# - contains hardware identification information such
3073 as type string and/or serial number
3074 ethaddr - Ethernet address
3076 These variables can be set only once (usually during manufacturing of
3077 the board). U-Boot refuses to delete or overwrite these variables
3078 once they have been set once.
3081 Further special Environment Variables:
3083 ver - Contains the U-Boot version string as printed
3084 with the "version" command. This variable is
3085 readonly (see CONFIG_VERSION_VARIABLE).
3088 Please note that changes to some configuration parameters may take
3089 only effect after the next boot (yes, that's just like Windoze :-).
3092 Command Line Parsing:
3093 =====================
3095 There are two different command line parsers available with U-Boot:
3096 the old "simple" one, and the much more powerful "hush" shell:
3098 Old, simple command line parser:
3099 --------------------------------
3101 - supports environment variables (through setenv / saveenv commands)
3102 - several commands on one line, separated by ';'
3103 - variable substitution using "... ${name} ..." syntax
3104 - special characters ('$', ';') can be escaped by prefixing with '\',
3106 setenv bootcmd bootm \${address}
3107 - You can also escape text by enclosing in single apostrophes, for example:
3108 setenv addip 'setenv bootargs $bootargs ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off'
3113 - similar to Bourne shell, with control structures like
3114 if...then...else...fi, for...do...done; while...do...done,
3115 until...do...done, ...
3116 - supports environment ("global") variables (through setenv / saveenv
3117 commands) and local shell variables (through standard shell syntax
3118 "name=value"); only environment variables can be used with "run"
3124 (1) If a command line (or an environment variable executed by a "run"
3125 command) contains several commands separated by semicolon, and
3126 one of these commands fails, then the remaining commands will be
3129 (2) If you execute several variables with one call to run (i. e.
3130 calling run with a list of variables as arguments), any failing
3131 command will cause "run" to terminate, i. e. the remaining
3132 variables are not executed.
3134 Note for Redundant Ethernet Interfaces:
3135 =======================================
3137 Some boards come with redundant Ethernet interfaces; U-Boot supports
3138 such configurations and is capable of automatic selection of a
3139 "working" interface when needed. MAC assignment works as follows:
3141 Network interfaces are numbered eth0, eth1, eth2, ... Corresponding
3142 MAC addresses can be stored in the environment as "ethaddr" (=>eth0),
3143 "eth1addr" (=>eth1), "eth2addr", ...
3145 If the network interface stores some valid MAC address (for instance
3146 in SROM), this is used as default address if there is NO correspon-
3147 ding setting in the environment; if the corresponding environment
3148 variable is set, this overrides the settings in the card; that means:
3150 o If the SROM has a valid MAC address, and there is no address in the
3151 environment, the SROM's address is used.
3153 o If there is no valid address in the SROM, and a definition in the
3154 environment exists, then the value from the environment variable is
3157 o If both the SROM and the environment contain a MAC address, and
3158 both addresses are the same, this MAC address is used.
3160 o If both the SROM and the environment contain a MAC address, and the
3161 addresses differ, the value from the environment is used and a
3164 o If neither SROM nor the environment contain a MAC address, an error
3171 U-Boot is capable of booting (and performing other auxiliary operations on)
3172 images in two formats:
3174 New uImage format (FIT)
3175 -----------------------
3177 Flexible and powerful format based on Flattened Image Tree -- FIT (similar
3178 to Flattened Device Tree). It allows the use of images with multiple
3179 components (several kernels, ramdisks, etc.), with contents protected by
3180 SHA1, MD5 or CRC32. More details are found in the doc/uImage.FIT directory.
3186 Old image format is based on binary files which can be basically anything,
3187 preceded by a special header; see the definitions in include/image.h for
3188 details; basically, the header defines the following image properties:
3190 * Target Operating System (Provisions for OpenBSD, NetBSD, FreeBSD,
3191 4.4BSD, Linux, SVR4, Esix, Solaris, Irix, SCO, Dell, NCR, VxWorks,
3192 LynxOS, pSOS, QNX, RTEMS, INTEGRITY;
3193 Currently supported: Linux, NetBSD, VxWorks, QNX, RTEMS, LynxOS,
3195 * Target CPU Architecture (Provisions for Alpha, ARM, AVR32, Intel x86,
3196 IA64, MIPS, NIOS, PowerPC, IBM S390, SuperH, Sparc, Sparc 64 Bit;
3197 Currently supported: ARM, AVR32, Intel x86, MIPS, NIOS, PowerPC).
3198 * Compression Type (uncompressed, gzip, bzip2)
3204 The header is marked by a special Magic Number, and both the header
3205 and the data portions of the image are secured against corruption by
3212 Although U-Boot should support any OS or standalone application
3213 easily, the main focus has always been on Linux during the design of
3216 U-Boot includes many features that so far have been part of some
3217 special "boot loader" code within the Linux kernel. Also, any
3218 "initrd" images to be used are no longer part of one big Linux image;
3219 instead, kernel and "initrd" are separate images. This implementation
3220 serves several purposes:
3222 - the same features can be used for other OS or standalone
3223 applications (for instance: using compressed images to reduce the
3224 Flash memory footprint)
3226 - it becomes much easier to port new Linux kernel versions because
3227 lots of low-level, hardware dependent stuff are done by U-Boot
3229 - the same Linux kernel image can now be used with different "initrd"
3230 images; of course this also means that different kernel images can
3231 be run with the same "initrd". This makes testing easier (you don't
3232 have to build a new "zImage.initrd" Linux image when you just
3233 change a file in your "initrd"). Also, a field-upgrade of the
3234 software is easier now.
3240 Porting Linux to U-Boot based systems:
3241 ---------------------------------------
3243 U-Boot cannot save you from doing all the necessary modifications to
3244 configure the Linux device drivers for use with your target hardware
3245 (no, we don't intend to provide a full virtual machine interface to
3248 But now you can ignore ALL boot loader code (in arch/ppc/mbxboot).
3250 Just make sure your machine specific header file (for instance
3251 include/asm-ppc/tqm8xx.h) includes the same definition of the Board
3252 Information structure as we define in include/asm-<arch>/u-boot.h,
3253 and make sure that your definition of IMAP_ADDR uses the same value
3254 as your U-Boot configuration in CONFIG_SYS_IMMR.
3257 Configuring the Linux kernel:
3258 -----------------------------
3260 No specific requirements for U-Boot. Make sure you have some root
3261 device (initial ramdisk, NFS) for your target system.
3264 Building a Linux Image:
3265 -----------------------
3267 With U-Boot, "normal" build targets like "zImage" or "bzImage" are
3268 not used. If you use recent kernel source, a new build target
3269 "uImage" will exist which automatically builds an image usable by
3270 U-Boot. Most older kernels also have support for a "pImage" target,
3271 which was introduced for our predecessor project PPCBoot and uses a
3272 100% compatible format.
3281 The "uImage" build target uses a special tool (in 'tools/mkimage') to
3282 encapsulate a compressed Linux kernel image with header information,
3283 CRC32 checksum etc. for use with U-Boot. This is what we are doing:
3285 * build a standard "vmlinux" kernel image (in ELF binary format):
3287 * convert the kernel into a raw binary image:
3289 ${CROSS_COMPILE}-objcopy -O binary \
3290 -R .note -R .comment \
3291 -S vmlinux linux.bin
3293 * compress the binary image:
3297 * package compressed binary image for U-Boot:
3299 mkimage -A ppc -O linux -T kernel -C gzip \
3300 -a 0 -e 0 -n "Linux Kernel Image" \
3301 -d linux.bin.gz uImage
3304 The "mkimage" tool can also be used to create ramdisk images for use
3305 with U-Boot, either separated from the Linux kernel image, or
3306 combined into one file. "mkimage" encapsulates the images with a 64
3307 byte header containing information about target architecture,
3308 operating system, image type, compression method, entry points, time
3309 stamp, CRC32 checksums, etc.
3311 "mkimage" can be called in two ways: to verify existing images and
3312 print the header information, or to build new images.
3314 In the first form (with "-l" option) mkimage lists the information
3315 contained in the header of an existing U-Boot image; this includes
3316 checksum verification:
3318 tools/mkimage -l image
3319 -l ==> list image header information
3321 The second form (with "-d" option) is used to build a U-Boot image
3322 from a "data file" which is used as image payload:
3324 tools/mkimage -A arch -O os -T type -C comp -a addr -e ep \
3325 -n name -d data_file image
3326 -A ==> set architecture to 'arch'
3327 -O ==> set operating system to 'os'
3328 -T ==> set image type to 'type'
3329 -C ==> set compression type 'comp'
3330 -a ==> set load address to 'addr' (hex)
3331 -e ==> set entry point to 'ep' (hex)
3332 -n ==> set image name to 'name'
3333 -d ==> use image data from 'datafile'
3335 Right now, all Linux kernels for PowerPC systems use the same load
3336 address (0x00000000), but the entry point address depends on the
3339 - 2.2.x kernels have the entry point at 0x0000000C,
3340 - 2.3.x and later kernels have the entry point at 0x00000000.
3342 So a typical call to build a U-Boot image would read:
3344 -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
3345 > -A ppc -O linux -T kernel -C gzip -a 0 -e 0 \
3346 > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux.gz \
3347 > examples/uImage.TQM850L
3348 Image Name: 2.4.4 kernel for TQM850L
3349 Created: Wed Jul 19 02:34:59 2000
3350 Image Type: PowerPC Linux Kernel Image (gzip compressed)
3351 Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
3352 Load Address: 0x00000000
3353 Entry Point: 0x00000000
3355 To verify the contents of the image (or check for corruption):
3357 -> tools/mkimage -l examples/uImage.TQM850L
3358 Image Name: 2.4.4 kernel for TQM850L
3359 Created: Wed Jul 19 02:34:59 2000
3360 Image Type: PowerPC Linux Kernel Image (gzip compressed)
3361 Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
3362 Load Address: 0x00000000
3363 Entry Point: 0x00000000
3365 NOTE: for embedded systems where boot time is critical you can trade
3366 speed for memory and install an UNCOMPRESSED image instead: this
3367 needs more space in Flash, but boots much faster since it does not
3368 need to be uncompressed:
3370 -> gunzip /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux.gz
3371 -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
3372 > -A ppc -O linux -T kernel -C none -a 0 -e 0 \
3373 > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux \
3374 > examples/uImage.TQM850L-uncompressed
3375 Image Name: 2.4.4 kernel for TQM850L
3376 Created: Wed Jul 19 02:34:59 2000
3377 Image Type: PowerPC Linux Kernel Image (uncompressed)
3378 Data Size: 792160 Bytes = 773.59 kB = 0.76 MB
3379 Load Address: 0x00000000
3380 Entry Point: 0x00000000
3383 Similar you can build U-Boot images from a 'ramdisk.image.gz' file
3384 when your kernel is intended to use an initial ramdisk:
3386 -> tools/mkimage -n 'Simple Ramdisk Image' \
3387 > -A ppc -O linux -T ramdisk -C gzip \
3388 > -d /LinuxPPC/images/SIMPLE-ramdisk.image.gz examples/simple-initrd
3389 Image Name: Simple Ramdisk Image
3390 Created: Wed Jan 12 14:01:50 2000
3391 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
3392 Data Size: 566530 Bytes = 553.25 kB = 0.54 MB
3393 Load Address: 0x00000000
3394 Entry Point: 0x00000000
3397 Installing a Linux Image:
3398 -------------------------
3400 To downloading a U-Boot image over the serial (console) interface,
3401 you must convert the image to S-Record format:
3403 objcopy -I binary -O srec examples/image examples/image.srec
3405 The 'objcopy' does not understand the information in the U-Boot
3406 image header, so the resulting S-Record file will be relative to
3407 address 0x00000000. To load it to a given address, you need to
3408 specify the target address as 'offset' parameter with the 'loads'
3411 Example: install the image to address 0x40100000 (which on the
3412 TQM8xxL is in the first Flash bank):
3414 => erase 40100000 401FFFFF
3420 ## Ready for S-Record download ...
3421 ~>examples/image.srec
3422 1 2 3 4 5 6 7 8 9 10 11 12 13 ...
3424 15989 15990 15991 15992
3425 [file transfer complete]
3427 ## Start Addr = 0x00000000
3430 You can check the success of the download using the 'iminfo' command;
3431 this includes a checksum verification so you can be sure no data
3432 corruption happened:
3436 ## Checking Image at 40100000 ...
3437 Image Name: 2.2.13 for initrd on TQM850L
3438 Image Type: PowerPC Linux Kernel Image (gzip compressed)
3439 Data Size: 335725 Bytes = 327 kB = 0 MB
3440 Load Address: 00000000
3441 Entry Point: 0000000c
3442 Verifying Checksum ... OK
3448 The "bootm" command is used to boot an application that is stored in
3449 memory (RAM or Flash). In case of a Linux kernel image, the contents
3450 of the "bootargs" environment variable is passed to the kernel as
3451 parameters. You can check and modify this variable using the
3452 "printenv" and "setenv" commands:
3455 => printenv bootargs
3456 bootargs=root=/dev/ram
3458 => setenv bootargs root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
3460 => printenv bootargs
3461 bootargs=root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
3464 ## Booting Linux kernel at 40020000 ...
3465 Image Name: 2.2.13 for NFS on TQM850L
3466 Image Type: PowerPC Linux Kernel Image (gzip compressed)
3467 Data Size: 381681 Bytes = 372 kB = 0 MB
3468 Load Address: 00000000
3469 Entry Point: 0000000c
3470 Verifying Checksum ... OK
3471 Uncompressing Kernel Image ... OK
3472 Linux version 2.2.13 (wd@denx.local.net) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:35:17 MEST 2000
3473 Boot arguments: root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
3474 time_init: decrementer frequency = 187500000/60
3475 Calibrating delay loop... 49.77 BogoMIPS
3476 Memory: 15208k available (700k kernel code, 444k data, 32k init) [c0000000,c1000000]
3479 If you want to boot a Linux kernel with initial RAM disk, you pass
3480 the memory addresses of both the kernel and the initrd image (PPBCOOT
3481 format!) to the "bootm" command:
3483 => imi 40100000 40200000
3485 ## Checking Image at 40100000 ...
3486 Image Name: 2.2.13 for initrd on TQM850L
3487 Image Type: PowerPC Linux Kernel Image (gzip compressed)
3488 Data Size: 335725 Bytes = 327 kB = 0 MB
3489 Load Address: 00000000
3490 Entry Point: 0000000c
3491 Verifying Checksum ... OK
3493 ## Checking Image at 40200000 ...
3494 Image Name: Simple Ramdisk Image
3495 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
3496 Data Size: 566530 Bytes = 553 kB = 0 MB
3497 Load Address: 00000000
3498 Entry Point: 00000000
3499 Verifying Checksum ... OK
3501 => bootm 40100000 40200000
3502 ## Booting Linux kernel at 40100000 ...
3503 Image Name: 2.2.13 for initrd on TQM850L
3504 Image Type: PowerPC Linux Kernel Image (gzip compressed)
3505 Data Size: 335725 Bytes = 327 kB = 0 MB
3506 Load Address: 00000000
3507 Entry Point: 0000000c
3508 Verifying Checksum ... OK
3509 Uncompressing Kernel Image ... OK
3510 ## Loading RAMDisk Image at 40200000 ...
3511 Image Name: Simple Ramdisk Image
3512 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
3513 Data Size: 566530 Bytes = 553 kB = 0 MB
3514 Load Address: 00000000
3515 Entry Point: 00000000
3516 Verifying Checksum ... OK
3517 Loading Ramdisk ... OK
3518 Linux version 2.2.13 (wd@denx.local.net) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:32:08 MEST 2000
3519 Boot arguments: root=/dev/ram
3520 time_init: decrementer frequency = 187500000/60
3521 Calibrating delay loop... 49.77 BogoMIPS
3523 RAMDISK: Compressed image found at block 0
3524 VFS: Mounted root (ext2 filesystem).
3528 Boot Linux and pass a flat device tree:
3531 First, U-Boot must be compiled with the appropriate defines. See the section
3532 titled "Linux Kernel Interface" above for a more in depth explanation. The
3533 following is an example of how to start a kernel and pass an updated
3539 oft=oftrees/mpc8540ads.dtb
3540 => tftp $oftaddr $oft
3541 Speed: 1000, full duplex
3543 TFTP from server 192.168.1.1; our IP address is 192.168.1.101
3544 Filename 'oftrees/mpc8540ads.dtb'.
3545 Load address: 0x300000
3548 Bytes transferred = 4106 (100a hex)
3549 => tftp $loadaddr $bootfile
3550 Speed: 1000, full duplex
3552 TFTP from server 192.168.1.1; our IP address is 192.168.1.2
3554 Load address: 0x200000
3555 Loading:############
3557 Bytes transferred = 1029407 (fb51f hex)
3562 => bootm $loadaddr - $oftaddr
3563 ## Booting image at 00200000 ...
3564 Image Name: Linux-2.6.17-dirty
3565 Image Type: PowerPC Linux Kernel Image (gzip compressed)
3566 Data Size: 1029343 Bytes = 1005.2 kB
3567 Load Address: 00000000
3568 Entry Point: 00000000
3569 Verifying Checksum ... OK
3570 Uncompressing Kernel Image ... OK
3571 Booting using flat device tree at 0x300000
3572 Using MPC85xx ADS machine description
3573 Memory CAM mapping: CAM0=256Mb, CAM1=256Mb, CAM2=0Mb residual: 0Mb
3577 More About U-Boot Image Types:
3578 ------------------------------
3580 U-Boot supports the following image types:
3582 "Standalone Programs" are directly runnable in the environment
3583 provided by U-Boot; it is expected that (if they behave
3584 well) you can continue to work in U-Boot after return from
3585 the Standalone Program.
3586 "OS Kernel Images" are usually images of some Embedded OS which
3587 will take over control completely. Usually these programs
3588 will install their own set of exception handlers, device
3589 drivers, set up the MMU, etc. - this means, that you cannot
3590 expect to re-enter U-Boot except by resetting the CPU.
3591 "RAMDisk Images" are more or less just data blocks, and their
3592 parameters (address, size) are passed to an OS kernel that is
3594 "Multi-File Images" contain several images, typically an OS
3595 (Linux) kernel image and one or more data images like
3596 RAMDisks. This construct is useful for instance when you want
3597 to boot over the network using BOOTP etc., where the boot
3598 server provides just a single image file, but you want to get
3599 for instance an OS kernel and a RAMDisk image.
3601 "Multi-File Images" start with a list of image sizes, each
3602 image size (in bytes) specified by an "uint32_t" in network
3603 byte order. This list is terminated by an "(uint32_t)0".
3604 Immediately after the terminating 0 follow the images, one by
3605 one, all aligned on "uint32_t" boundaries (size rounded up to
3606 a multiple of 4 bytes).
3608 "Firmware Images" are binary images containing firmware (like
3609 U-Boot or FPGA images) which usually will be programmed to
3612 "Script files" are command sequences that will be executed by
3613 U-Boot's command interpreter; this feature is especially
3614 useful when you configure U-Boot to use a real shell (hush)
3615 as command interpreter.
3621 One of the features of U-Boot is that you can dynamically load and
3622 run "standalone" applications, which can use some resources of
3623 U-Boot like console I/O functions or interrupt services.
3625 Two simple examples are included with the sources:
3630 'examples/hello_world.c' contains a small "Hello World" Demo
3631 application; it is automatically compiled when you build U-Boot.
3632 It's configured to run at address 0x00040004, so you can play with it
3636 ## Ready for S-Record download ...
3637 ~>examples/hello_world.srec
3638 1 2 3 4 5 6 7 8 9 10 11 ...
3639 [file transfer complete]
3641 ## Start Addr = 0x00040004
3643 => go 40004 Hello World! This is a test.
3644 ## Starting application at 0x00040004 ...
3655 Hit any key to exit ...
3657 ## Application terminated, rc = 0x0
3659 Another example, which demonstrates how to register a CPM interrupt
3660 handler with the U-Boot code, can be found in 'examples/timer.c'.
3661 Here, a CPM timer is set up to generate an interrupt every second.
3662 The interrupt service routine is trivial, just printing a '.'
3663 character, but this is just a demo program. The application can be
3664 controlled by the following keys:
3666 ? - print current values og the CPM Timer registers
3667 b - enable interrupts and start timer
3668 e - stop timer and disable interrupts
3669 q - quit application
3672 ## Ready for S-Record download ...
3673 ~>examples/timer.srec
3674 1 2 3 4 5 6 7 8 9 10 11 ...
3675 [file transfer complete]
3677 ## Start Addr = 0x00040004
3680 ## Starting application at 0x00040004 ...
3683 tgcr @ 0xfff00980, tmr @ 0xfff00990, trr @ 0xfff00994, tcr @ 0xfff00998, tcn @ 0xfff0099c, ter @ 0xfff009b0
3686 [q, b, e, ?] Set interval 1000000 us
3689 [q, b, e, ?] ........
3690 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0xef6, ter=0x0
3693 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x2ad4, ter=0x0
3696 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x1efc, ter=0x0
3699 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x169d, ter=0x0
3701 [q, b, e, ?] ...Stopping timer
3703 [q, b, e, ?] ## Application terminated, rc = 0x0
3709 Over time, many people have reported problems when trying to use the
3710 "minicom" terminal emulation program for serial download. I (wd)
3711 consider minicom to be broken, and recommend not to use it. Under
3712 Unix, I recommend to use C-Kermit for general purpose use (and
3713 especially for kermit binary protocol download ("loadb" command), and
3714 use "cu" for S-Record download ("loads" command).
3716 Nevertheless, if you absolutely want to use it try adding this
3717 configuration to your "File transfer protocols" section:
3719 Name Program Name U/D FullScr IO-Red. Multi
3720 X kermit /usr/bin/kermit -i -l %l -s Y U Y N N
3721 Y kermit /usr/bin/kermit -i -l %l -r N D Y N N
3727 Starting at version 0.9.2, U-Boot supports NetBSD both as host
3728 (build U-Boot) and target system (boots NetBSD/mpc8xx).
3730 Building requires a cross environment; it is known to work on
3731 NetBSD/i386 with the cross-powerpc-netbsd-1.3 package (you will also
3732 need gmake since the Makefiles are not compatible with BSD make).
3733 Note that the cross-powerpc package does not install include files;
3734 attempting to build U-Boot will fail because <machine/ansi.h> is
3735 missing. This file has to be installed and patched manually:
3737 # cd /usr/pkg/cross/powerpc-netbsd/include
3739 # ln -s powerpc machine
3740 # cp /usr/src/sys/arch/powerpc/include/ansi.h powerpc/ansi.h
3741 # ${EDIT} powerpc/ansi.h ## must remove __va_list, _BSD_VA_LIST
3743 Native builds *don't* work due to incompatibilities between native
3744 and U-Boot include files.
3746 Booting assumes that (the first part of) the image booted is a
3747 stage-2 loader which in turn loads and then invokes the kernel
3748 proper. Loader sources will eventually appear in the NetBSD source
3749 tree (probably in sys/arc/mpc8xx/stand/u-boot_stage2/); in the
3750 meantime, see ftp://ftp.denx.de/pub/u-boot/ppcboot_stage2.tar.gz
3753 Implementation Internals:
3754 =========================
3756 The following is not intended to be a complete description of every
3757 implementation detail. However, it should help to understand the
3758 inner workings of U-Boot and make it easier to port it to custom
3762 Initial Stack, Global Data:
3763 ---------------------------
3765 The implementation of U-Boot is complicated by the fact that U-Boot
3766 starts running out of ROM (flash memory), usually without access to
3767 system RAM (because the memory controller is not initialized yet).
3768 This means that we don't have writable Data or BSS segments, and BSS
3769 is not initialized as zero. To be able to get a C environment working
3770 at all, we have to allocate at least a minimal stack. Implementation
3771 options for this are defined and restricted by the CPU used: Some CPU
3772 models provide on-chip memory (like the IMMR area on MPC8xx and
3773 MPC826x processors), on others (parts of) the data cache can be
3774 locked as (mis-) used as memory, etc.
3776 Chris Hallinan posted a good summary of these issues to the
3777 U-Boot mailing list:
3779 Subject: RE: [U-Boot-Users] RE: More On Memory Bank x (nothingness)?
3780 From: "Chris Hallinan" <clh@net1plus.com>
3781 Date: Mon, 10 Feb 2003 16:43:46 -0500 (22:43 MET)
3784 Correct me if I'm wrong, folks, but the way I understand it
3785 is this: Using DCACHE as initial RAM for Stack, etc, does not
3786 require any physical RAM backing up the cache. The cleverness
3787 is that the cache is being used as a temporary supply of
3788 necessary storage before the SDRAM controller is setup. It's
3789 beyond the scope of this list to explain the details, but you
3790 can see how this works by studying the cache architecture and
3791 operation in the architecture and processor-specific manuals.
3793 OCM is On Chip Memory, which I believe the 405GP has 4K. It
3794 is another option for the system designer to use as an
3795 initial stack/RAM area prior to SDRAM being available. Either
3796 option should work for you. Using CS 4 should be fine if your
3797 board designers haven't used it for something that would
3798 cause you grief during the initial boot! It is frequently not
3801 CONFIG_SYS_INIT_RAM_ADDR should be somewhere that won't interfere
3802 with your processor/board/system design. The default value
3803 you will find in any recent u-boot distribution in
3804 walnut.h should work for you. I'd set it to a value larger
3805 than your SDRAM module. If you have a 64MB SDRAM module, set
3806 it above 400_0000. Just make sure your board has no resources
3807 that are supposed to respond to that address! That code in
3808 start.S has been around a while and should work as is when
3809 you get the config right.
3814 It is essential to remember this, since it has some impact on the C
3815 code for the initialization procedures:
3817 * Initialized global data (data segment) is read-only. Do not attempt
3820 * Do not use any uninitialized global data (or implicitely initialized
3821 as zero data - BSS segment) at all - this is undefined, initiali-
3822 zation is performed later (when relocating to RAM).
3824 * Stack space is very limited. Avoid big data buffers or things like
3827 Having only the stack as writable memory limits means we cannot use
3828 normal global data to share information beween the code. But it
3829 turned out that the implementation of U-Boot can be greatly
3830 simplified by making a global data structure (gd_t) available to all
3831 functions. We could pass a pointer to this data as argument to _all_
3832 functions, but this would bloat the code. Instead we use a feature of
3833 the GCC compiler (Global Register Variables) to share the data: we
3834 place a pointer (gd) to the global data into a register which we
3835 reserve for this purpose.
3837 When choosing a register for such a purpose we are restricted by the
3838 relevant (E)ABI specifications for the current architecture, and by
3839 GCC's implementation.
3841 For PowerPC, the following registers have specific use:
3843 R2: reserved for system use
3844 R3-R4: parameter passing and return values
3845 R5-R10: parameter passing
3846 R13: small data area pointer
3850 (U-Boot also uses R14 as internal GOT pointer.)
3852 ==> U-Boot will use R2 to hold a pointer to the global data
3854 Note: on PPC, we could use a static initializer (since the
3855 address of the global data structure is known at compile time),
3856 but it turned out that reserving a register results in somewhat
3857 smaller code - although the code savings are not that big (on
3858 average for all boards 752 bytes for the whole U-Boot image,
3859 624 text + 127 data).
3861 On Blackfin, the normal C ABI (except for P5) is followed as documented here:
3862 http://docs.blackfin.uclinux.org/doku.php?id=application_binary_interface
3864 ==> U-Boot will use P5 to hold a pointer to the global data
3866 On ARM, the following registers are used:
3868 R0: function argument word/integer result
3869 R1-R3: function argument word
3871 R10: stack limit (used only if stack checking if enabled)
3872 R11: argument (frame) pointer
3873 R12: temporary workspace
3876 R15: program counter
3878 ==> U-Boot will use R8 to hold a pointer to the global data
3880 NOTE: DECLARE_GLOBAL_DATA_PTR must be used with file-global scope,
3881 or current versions of GCC may "optimize" the code too much.
3886 U-Boot runs in system state and uses physical addresses, i.e. the
3887 MMU is not used either for address mapping nor for memory protection.
3889 The available memory is mapped to fixed addresses using the memory
3890 controller. In this process, a contiguous block is formed for each
3891 memory type (Flash, SDRAM, SRAM), even when it consists of several
3892 physical memory banks.
3894 U-Boot is installed in the first 128 kB of the first Flash bank (on
3895 TQM8xxL modules this is the range 0x40000000 ... 0x4001FFFF). After
3896 booting and sizing and initializing DRAM, the code relocates itself
3897 to the upper end of DRAM. Immediately below the U-Boot code some
3898 memory is reserved for use by malloc() [see CONFIG_SYS_MALLOC_LEN
3899 configuration setting]. Below that, a structure with global Board
3900 Info data is placed, followed by the stack (growing downward).
3902 Additionally, some exception handler code is copied to the low 8 kB
3903 of DRAM (0x00000000 ... 0x00001FFF).
3905 So a typical memory configuration with 16 MB of DRAM could look like
3908 0x0000 0000 Exception Vector code
3911 0x0000 2000 Free for Application Use
3917 0x00FB FF20 Monitor Stack (Growing downward)
3918 0x00FB FFAC Board Info Data and permanent copy of global data
3919 0x00FC 0000 Malloc Arena
3922 0x00FE 0000 RAM Copy of Monitor Code
3923 ... eventually: LCD or video framebuffer
3924 ... eventually: pRAM (Protected RAM - unchanged by reset)
3925 0x00FF FFFF [End of RAM]
3928 System Initialization:
3929 ----------------------
3931 In the reset configuration, U-Boot starts at the reset entry point
3932 (on most PowerPC systems at address 0x00000100). Because of the reset
3933 configuration for CS0# this is a mirror of the onboard Flash memory.
3934 To be able to re-map memory U-Boot then jumps to its link address.
3935 To be able to implement the initialization code in C, a (small!)
3936 initial stack is set up in the internal Dual Ported RAM (in case CPUs
3937 which provide such a feature like MPC8xx or MPC8260), or in a locked
3938 part of the data cache. After that, U-Boot initializes the CPU core,
3939 the caches and the SIU.
3941 Next, all (potentially) available memory banks are mapped using a
3942 preliminary mapping. For example, we put them on 512 MB boundaries
3943 (multiples of 0x20000000: SDRAM on 0x00000000 and 0x20000000, Flash
3944 on 0x40000000 and 0x60000000, SRAM on 0x80000000). Then UPM A is
3945 programmed for SDRAM access. Using the temporary configuration, a
3946 simple memory test is run that determines the size of the SDRAM
3949 When there is more than one SDRAM bank, and the banks are of
3950 different size, the largest is mapped first. For equal size, the first
3951 bank (CS2#) is mapped first. The first mapping is always for address
3952 0x00000000, with any additional banks following immediately to create
3953 contiguous memory starting from 0.
3955 Then, the monitor installs itself at the upper end of the SDRAM area
3956 and allocates memory for use by malloc() and for the global Board
3957 Info data; also, the exception vector code is copied to the low RAM
3958 pages, and the final stack is set up.
3960 Only after this relocation will you have a "normal" C environment;
3961 until that you are restricted in several ways, mostly because you are
3962 running from ROM, and because the code will have to be relocated to a
3966 U-Boot Porting Guide:
3967 ----------------------
3969 [Based on messages by Jerry Van Baren in the U-Boot-Users mailing
3973 int main (int argc, char *argv[])
3975 sighandler_t no_more_time;
3977 signal (SIGALRM, no_more_time);
3978 alarm (PROJECT_DEADLINE - toSec (3 * WEEK));
3980 if (available_money > available_manpower) {
3981 pay consultant to port U-Boot;
3985 Download latest U-Boot source;
3987 Subscribe to u-boot mailing list;
3990 email ("Hi, I am new to U-Boot, how do I get started?");
3994 Read the README file in the top level directory;
3995 Read http://www.denx.de/twiki/bin/view/DULG/Manual ;
3996 Read the source, Luke;
3999 if (available_money > toLocalCurrency ($2500)) {
4002 Add a lot of aggravation and time;
4005 Create your own board support subdirectory;
4007 Create your own board config file;
4011 Add / modify source code;
4015 email ("Hi, I am having problems...");
4017 Send patch file to Wolfgang;
4022 void no_more_time (int sig)
4031 All contributions to U-Boot should conform to the Linux kernel
4032 coding style; see the file "Documentation/CodingStyle" and the script
4033 "scripts/Lindent" in your Linux kernel source directory. In sources
4034 originating from U-Boot a style corresponding to "Lindent -pcs" (adding
4035 spaces before parameters to function calls) is actually used.
4037 Source files originating from a different project (for example the
4038 MTD subsystem) are generally exempt from these guidelines and are not
4039 reformated to ease subsequent migration to newer versions of those
4042 Please note that U-Boot is implemented in C (and to some small parts in
4043 Assembler); no C++ is used, so please do not use C++ style comments (//)
4046 Please also stick to the following formatting rules:
4047 - remove any trailing white space
4048 - use TAB characters for indentation, not spaces
4049 - make sure NOT to use DOS '\r\n' line feeds
4050 - do not add more than 2 empty lines to source files
4051 - do not add trailing empty lines to source files
4053 Submissions which do not conform to the standards may be returned
4054 with a request to reformat the changes.
4060 Since the number of patches for U-Boot is growing, we need to
4061 establish some rules. Submissions which do not conform to these rules
4062 may be rejected, even when they contain important and valuable stuff.
4064 Please see http://www.denx.de/wiki/U-Boot/Patches for details.
4066 Patches shall be sent to the u-boot mailing list <u-boot@lists.denx.de>;
4067 see http://lists.denx.de/mailman/listinfo/u-boot
4069 When you send a patch, please include the following information with
4072 * For bug fixes: a description of the bug and how your patch fixes
4073 this bug. Please try to include a way of demonstrating that the
4074 patch actually fixes something.
4076 * For new features: a description of the feature and your
4079 * A CHANGELOG entry as plaintext (separate from the patch)
4081 * For major contributions, your entry to the CREDITS file
4083 * When you add support for a new board, don't forget to add this
4084 board to the MAKEALL script, too.
4086 * If your patch adds new configuration options, don't forget to
4087 document these in the README file.
4089 * The patch itself. If you are using git (which is *strongly*
4090 recommended) you can easily generate the patch using the
4091 "git-format-patch". If you then use "git-send-email" to send it to
4092 the U-Boot mailing list, you will avoid most of the common problems
4093 with some other mail clients.
4095 If you cannot use git, use "diff -purN OLD NEW". If your version of
4096 diff does not support these options, then get the latest version of
4099 The current directory when running this command shall be the parent
4100 directory of the U-Boot source tree (i. e. please make sure that
4101 your patch includes sufficient directory information for the
4104 We prefer patches as plain text. MIME attachments are discouraged,
4105 and compressed attachments must not be used.
4107 * If one logical set of modifications affects or creates several
4108 files, all these changes shall be submitted in a SINGLE patch file.
4110 * Changesets that contain different, unrelated modifications shall be
4111 submitted as SEPARATE patches, one patch per changeset.
4116 * Before sending the patch, run the MAKEALL script on your patched
4117 source tree and make sure that no errors or warnings are reported
4118 for any of the boards.
4120 * Keep your modifications to the necessary minimum: A patch
4121 containing several unrelated changes or arbitrary reformats will be
4122 returned with a request to re-formatting / split it.
4124 * If you modify existing code, make sure that your new code does not
4125 add to the memory footprint of the code ;-) Small is beautiful!
4126 When adding new features, these should compile conditionally only
4127 (using #ifdef), and the resulting code with the new feature
4128 disabled must not need more memory than the old code without your
4131 * Remember that there is a size limit of 100 kB per message on the
4132 u-boot mailing list. Bigger patches will be moderated. If they are
4133 reasonable and not too big, they will be acknowledged. But patches
4134 bigger than the size limit should be avoided.
projects / karo-tx-uboot.git / blob