]> git.kernelconcepts.de Git - karo-tx-uboot.git/blob - doc/README.dfutftp
arm64: add support for Ka-Ro TXSD-410E
[karo-tx-uboot.git] / doc / README.dfutftp
1 Device Firmware Upgrade (DFU) - extension to use TFTP
2 =====================================================
3
4 Why?
5 ----
6
7 * Update TFTP (CONFIG_UPDATE_TFTP) only supports writing
8 code to NAND memory via TFTP.
9 * DFU supports writing data to the variety of mediums (NAND,
10 eMMC, SD, partitions, RAM, etc) via USB.
11
12 Combination of both solves their shortcomings!
13
14
15 Overview
16 --------
17
18 This document briefly describes how to use DFU for
19 upgrading firmware (e.g. kernel, u-boot, rootfs, etc.)
20 via TFTP protocol.
21
22 By using Ethernet (TFTP protocol to be precise) it is
23 possible to overcome the major problem of USB based DFU -
24 the relatively low transfer speed for large files.
25 This was caused by DFU standard, which imposed utilization
26 of only EP0 for transfer. By using Ethernet we can circumvent
27 this shortcoming.
28
29 Beagle Bone Black rev. C (BBB) powered by TI's am335x CPU has
30 been used as a demo board.
31
32 To utilize this feature, one needs to first enable support
33 for USB based DFU (CONFIG_DFU_*) and DFU TFTP update
34 (CONFIG_DFU_TFTP) described in ./doc/README.update.
35
36 The "dfu" command has been extended to support transfer via TFTP - one
37 needs to type for example "dfu tftp 0 mmc 0"
38
39 This feature does not depend on "fitupd" command enabled.
40
41 As of this writing (SHA1:8d77576371381ade83de475bb639949b44941e8c v2015.10-rc2)
42 the update.c code is not enabled (CONFIG_UPDATE_TFTP) by any board in the
43 contemporary u-boot tree.
44
45
46 Environment variables
47 ---------------------
48
49 The "dfu tftp" command can be used in the "preboot" environment variable
50 (when it is enabled by defining CONFIG_PREBOOT).
51 This is the preferable way of using this command in the early boot stage
52 as opposed to legacy update_tftp() function invocation.
53
54
55 Beagle Bone Black (BBB) setup
56 -----------------------------
57
58 1. Setup tftp env variables:
59    *  select desired eth device - 'ethact' variable ["ethact=cpsw"]
60       (use "bdinfo" to check current setting)
61    *  setup "serverip" and "ipaddr" variables
62    *  set "loadaddr" as a fixed buffer where incoming data is placed
63       ["loadaddr=0x81000000"]
64
65 #########
66 # BONUS #
67 #########
68 It is possible to use USB interface to emulate ETH connection by setting
69 "ethact=usb_ether". In this way one can have very fast DFU transfer via USB.
70
71 For 33MiB test image the transfer rate was 1MiB/s for ETH over USB and 200KiB/s
72 for pure DFU USB transfer.
73
74 2. Setup update_tftp variables:
75    *  set "updatefile" - the file name to be downloaded via TFTP (stored on
76       the HOST at e.g. /srv/tftp)
77
78 3. If required, to update firmware on boot, put the "dfu tftp 0 mmc 0" in the
79     "preboot" env variable. Otherwise use this command from u-boot prompt.
80
81 4. Inspect "dfu" specific variables:
82    * "dfu_alt_info" - information about available DFU entities
83    * "dfu_bufsiz"   - variable to set buffer size [in bytes] - when it is not
84                     possible to set large enough default buffer (8 MiB @ BBB)
85
86
87
88 FIT image format for download
89 -----------------------------
90
91 To create FIT image for download one should follow the update tftp README file
92 (./doc/README.update) with one notable difference:
93
94 The original snippet of ./doc/uImage.FIT/update_uboot.its
95
96         images {
97                 update@1 {
98                         description = "U-Boot binary";
99
100 should look like
101
102         images {
103                 u-boot.bin@1 {
104                         description = "U-Boot binary";
105
106 where "u-boot.bin" is the DFU entity name to be stored.
107
108
109
110 To do
111 -----
112
113 * Extend dfu-util command to support TFTP based transfers
114 * Upload support (via TFTP)