drivers/ddr/fsl/ctrl_regs.c

   1 /*
   2  * Copyright 2008-2014 Freescale Semiconductor, Inc.
   3  *
   4  * SPDX-License-Identifier:     GPL-2.0+
   5  */
   6
   7 /*
   8  * Generic driver for Freescale DDR/DDR2/DDR3 memory controller.
   9  * Based on code from spd_sdram.c
  10  * Author: James Yang [at freescale.com]
  11  */
  12
  13 #include <common.h>
  14 #include <fsl_ddr_sdram.h>
  15
  16 #include <fsl_ddr.h>
  17 #include <fsl_immap.h>
  18 #include <asm/io.h>
  19
  20 unsigned int picos_to_mclk(unsigned int picos);
  21
  22 /*
  23  * Determine Rtt value.
  24  *
  25  * This should likely be either board or controller specific.
  26  *
  27  * Rtt(nominal) - DDR2:
  28  *      0 = Rtt disabled
  29  *      1 = 75 ohm
  30  *      2 = 150 ohm
  31  *      3 = 50 ohm
  32  * Rtt(nominal) - DDR3:
  33  *      0 = Rtt disabled
  34  *      1 = 60 ohm
  35  *      2 = 120 ohm
  36  *      3 = 40 ohm
  37  *      4 = 20 ohm
  38  *      5 = 30 ohm
  39  *
  40  * FIXME: Apparently 8641 needs a value of 2
  41  * FIXME: Old code seys if 667 MHz or higher, use 3 on 8572
  42  *
  43  * FIXME: There was some effort down this line earlier:
  44  *
  45  *      unsigned int i;
  46  *      for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL/2; i++) {
  47  *              if (popts->dimmslot[i].num_valid_cs
  48  *                  && (popts->cs_local_opts[2*i].odt_rd_cfg
  49  *                      || popts->cs_local_opts[2*i].odt_wr_cfg)) {
  50  *                      rtt = 2;
  51  *                      break;
  52  *              }
  53  *      }
  54  */
  55 static inline int fsl_ddr_get_rtt(void)
  56 {
  57         int rtt;
  58
  59 #if defined(CONFIG_SYS_FSL_DDR1)
  60         rtt = 0;
  61 #elif defined(CONFIG_SYS_FSL_DDR2)
  62         rtt = 3;
  63 #else
  64         rtt = 0;
  65 #endif
  66
  67         return rtt;
  68 }
  69
  70 #ifdef CONFIG_SYS_FSL_DDR4
  71 /*
  72  * compute CAS write latency according to DDR4 spec
  73  * CWL = 9 for <= 1600MT/s
  74  *       10 for <= 1866MT/s
  75  *       11 for <= 2133MT/s
  76  *       12 for <= 2400MT/s
  77  *       14 for <= 2667MT/s
  78  *       16 for <= 2933MT/s
  79  *       18 for higher
  80  */
  81 static inline unsigned int compute_cas_write_latency(void)
  82 {
  83         unsigned int cwl;
  84         const unsigned int mclk_ps = get_memory_clk_period_ps();
  85         if (mclk_ps >= 1250)
  86                 cwl = 9;
  87         else if (mclk_ps >= 1070)
  88                 cwl = 10;
  89         else if (mclk_ps >= 935)
  90                 cwl = 11;
  91         else if (mclk_ps >= 833)
  92                 cwl = 12;
  93         else if (mclk_ps >= 750)
  94                 cwl = 14;
  95         else if (mclk_ps >= 681)
  96                 cwl = 16;
  97         else
  98                 cwl = 18;
  99
 100         return cwl;
 101 }
 102 #else
 103 /*
 104  * compute the CAS write latency according to DDR3 spec
 105  * CWL = 5 if tCK >= 2.5ns
 106  *       6 if 2.5ns > tCK >= 1.875ns
 107  *       7 if 1.875ns > tCK >= 1.5ns
 108  *       8 if 1.5ns > tCK >= 1.25ns
 109  *       9 if 1.25ns > tCK >= 1.07ns
 110  *       10 if 1.07ns > tCK >= 0.935ns
 111  *       11 if 0.935ns > tCK >= 0.833ns
 112  *       12 if 0.833ns > tCK >= 0.75ns
 113  */
 114 static inline unsigned int compute_cas_write_latency(void)
 115 {
 116         unsigned int cwl;
 117         const unsigned int mclk_ps = get_memory_clk_period_ps();
 118
 119         if (mclk_ps >= 2500)
 120                 cwl = 5;
 121         else if (mclk_ps >= 1875)
 122                 cwl = 6;
 123         else if (mclk_ps >= 1500)
 124                 cwl = 7;
 125         else if (mclk_ps >= 1250)
 126                 cwl = 8;
 127         else if (mclk_ps >= 1070)
 128                 cwl = 9;
 129         else if (mclk_ps >= 935)
 130                 cwl = 10;
 131         else if (mclk_ps >= 833)
 132                 cwl = 11;
 133         else if (mclk_ps >= 750)
 134                 cwl = 12;
 135         else {
 136                 cwl = 12;
 137                 printf("Warning: CWL is out of range\n");
 138         }
 139         return cwl;
 140 }
 141 #endif
 142
 143 /* Chip Select Configuration (CSn_CONFIG) */
 144 static void set_csn_config(int dimm_number, int i, fsl_ddr_cfg_regs_t *ddr,
 145                                const memctl_options_t *popts,
 146                                const dimm_params_t *dimm_params)
 147 {
 148         unsigned int cs_n_en = 0; /* Chip Select enable */
 149         unsigned int intlv_en = 0; /* Memory controller interleave enable */
 150         unsigned int intlv_ctl = 0; /* Interleaving control */
 151         unsigned int ap_n_en = 0; /* Chip select n auto-precharge enable */
 152         unsigned int odt_rd_cfg = 0; /* ODT for reads configuration */
 153         unsigned int odt_wr_cfg = 0; /* ODT for writes configuration */
 154         unsigned int ba_bits_cs_n = 0; /* Num of bank bits for SDRAM on CSn */
 155         unsigned int row_bits_cs_n = 0; /* Num of row bits for SDRAM on CSn */
 156         unsigned int col_bits_cs_n = 0; /* Num of ocl bits for SDRAM on CSn */
 157         int go_config = 0;
 158 #ifdef CONFIG_SYS_FSL_DDR4
 159         unsigned int bg_bits_cs_n = 0; /* Num of bank group bits */
 160 #else
 161         unsigned int n_banks_per_sdram_device;
 162 #endif
 163
 164         /* Compute CS_CONFIG only for existing ranks of each DIMM.  */
 165         switch (i) {
 166         case 0:
 167                 if (dimm_params[dimm_number].n_ranks > 0) {
 168                         go_config = 1;
 169                         /* These fields only available in CS0_CONFIG */
 170                         if (!popts->memctl_interleaving)
 171                                 break;
 172                         switch (popts->memctl_interleaving_mode) {
 173                         case FSL_DDR_256B_INTERLEAVING:
 174                         case FSL_DDR_CACHE_LINE_INTERLEAVING:
 175                         case FSL_DDR_PAGE_INTERLEAVING:
 176                         case FSL_DDR_BANK_INTERLEAVING:
 177                         case FSL_DDR_SUPERBANK_INTERLEAVING:
 178                                 intlv_en = popts->memctl_interleaving;
 179                                 intlv_ctl = popts->memctl_interleaving_mode;
 180                                 break;
 181                         default:
 182                                 break;
 183                         }
 184                 }
 185                 break;
 186         case 1:
 187                 if ((dimm_number == 0 && dimm_params[0].n_ranks > 1) || \
 188                     (dimm_number == 1 && dimm_params[1].n_ranks > 0))
 189                         go_config = 1;
 190                 break;
 191         case 2:
 192                 if ((dimm_number == 0 && dimm_params[0].n_ranks > 2) || \
 193                    (dimm_number >= 1 && dimm_params[dimm_number].n_ranks > 0))
 194                         go_config = 1;
 195                 break;
 196         case 3:
 197                 if ((dimm_number == 0 && dimm_params[0].n_ranks > 3) || \
 198                     (dimm_number == 1 && dimm_params[1].n_ranks > 1) || \
 199                     (dimm_number == 3 && dimm_params[3].n_ranks > 0))
 200                         go_config = 1;
 201                 break;
 202         default:
 203                 break;
 204         }
 205         if (go_config) {
 206                 cs_n_en = 1;
 207                 ap_n_en = popts->cs_local_opts[i].auto_precharge;
 208                 odt_rd_cfg = popts->cs_local_opts[i].odt_rd_cfg;
 209                 odt_wr_cfg = popts->cs_local_opts[i].odt_wr_cfg;
 210 #ifdef CONFIG_SYS_FSL_DDR4
 211                 ba_bits_cs_n = dimm_params[dimm_number].bank_addr_bits;
 212                 bg_bits_cs_n = dimm_params[dimm_number].bank_group_bits;
 213 #else
 214                 n_banks_per_sdram_device
 215                         = dimm_params[dimm_number].n_banks_per_sdram_device;
 216                 ba_bits_cs_n = __ilog2(n_banks_per_sdram_device) - 2;
 217 #endif
 218                 row_bits_cs_n = dimm_params[dimm_number].n_row_addr - 12;
 219                 col_bits_cs_n = dimm_params[dimm_number].n_col_addr - 8;
 220         }
 221         ddr->cs[i].config = (0
 222                 | ((cs_n_en & 0x1) << 31)
 223                 | ((intlv_en & 0x3) << 29)
 224                 | ((intlv_ctl & 0xf) << 24)
 225                 | ((ap_n_en & 0x1) << 23)
 226
 227                 /* XXX: some implementation only have 1 bit starting at left */
 228                 | ((odt_rd_cfg & 0x7) << 20)
 229
 230                 /* XXX: Some implementation only have 1 bit starting at left */
 231                 | ((odt_wr_cfg & 0x7) << 16)
 232
 233                 | ((ba_bits_cs_n & 0x3) << 14)
 234                 | ((row_bits_cs_n & 0x7) << 8)
 235 #ifdef CONFIG_SYS_FSL_DDR4
 236                 | ((bg_bits_cs_n & 0x3) << 4)
 237 #endif
 238                 | ((col_bits_cs_n & 0x7) << 0)
 239                 );
 240         debug("FSLDDR: cs[%d]_config = 0x%08x\n", i,ddr->cs[i].config);
 241 }
 242
 243 /* Chip Select Configuration 2 (CSn_CONFIG_2) */
 244 /* FIXME: 8572 */
 245 static void set_csn_config_2(int i, fsl_ddr_cfg_regs_t *ddr)
 246 {
 247         unsigned int pasr_cfg = 0;      /* Partial array self refresh config */
 248
 249         ddr->cs[i].config_2 = ((pasr_cfg & 7) << 24);
 250         debug("FSLDDR: cs[%d]_config_2 = 0x%08x\n", i, ddr->cs[i].config_2);
 251 }
 252
 253 /* -3E = 667 CL5, -25 = CL6 800, -25E = CL5 800 */
 254
 255 #if !defined(CONFIG_SYS_FSL_DDR1)
 256 /*
 257  * Check DIMM configuration, return 2 if quad-rank or two dual-rank
 258  * Return 1 if other two slots configuration. Return 0 if single slot.
 259  */
 260 static inline int avoid_odt_overlap(const dimm_params_t *dimm_params)
 261 {
 262 #if CONFIG_DIMM_SLOTS_PER_CTLR == 1
 263         if (dimm_params[0].n_ranks == 4)
 264                 return 2;
 265 #endif
 266
 267 #if CONFIG_DIMM_SLOTS_PER_CTLR == 2
 268         if ((dimm_params[0].n_ranks == 2) &&
 269                 (dimm_params[1].n_ranks == 2))
 270                 return 2;
 271
 272 #ifdef CONFIG_FSL_DDR_FIRST_SLOT_QUAD_CAPABLE
 273         if (dimm_params[0].n_ranks == 4)
 274                 return 2;
 275 #endif
 276
 277         if ((dimm_params[0].n_ranks != 0) &&
 278             (dimm_params[2].n_ranks != 0))
 279                 return 1;
 280 #endif
 281         return 0;
 282 }
 283
 284 /*
 285  * DDR SDRAM Timing Configuration 0 (TIMING_CFG_0)
 286  *
 287  * Avoid writing for DDR I.  The new PQ38 DDR controller
 288  * dreams up non-zero default values to be backwards compatible.
 289  */
 290 static void set_timing_cfg_0(fsl_ddr_cfg_regs_t *ddr,
 291                                 const memctl_options_t *popts,
 292                                 const dimm_params_t *dimm_params)
 293 {
 294         unsigned char trwt_mclk = 0;   /* Read-to-write turnaround */
 295         unsigned char twrt_mclk = 0;   /* Write-to-read turnaround */
 296         /* 7.5 ns on -3E; 0 means WL - CL + BL/2 + 1 */
 297         unsigned char trrt_mclk = 0;   /* Read-to-read turnaround */
 298         unsigned char twwt_mclk = 0;   /* Write-to-write turnaround */
 299
 300         /* Active powerdown exit timing (tXARD and tXARDS). */
 301         unsigned char act_pd_exit_mclk;
 302         /* Precharge powerdown exit timing (tXP). */
 303         unsigned char pre_pd_exit_mclk;
 304         /* ODT powerdown exit timing (tAXPD). */
 305         unsigned char taxpd_mclk = 0;
 306         /* Mode register set cycle time (tMRD). */
 307         unsigned char tmrd_mclk;
 308 #if defined(CONFIG_SYS_FSL_DDR4) || defined(CONFIG_SYS_FSL_DDR3)
 309         const unsigned int mclk_ps = get_memory_clk_period_ps();
 310 #endif
 311
 312 #ifdef CONFIG_SYS_FSL_DDR4
 313         /* tXP=max(4nCK, 6ns) */
 314         int txp = max((int)mclk_ps * 4, 6000); /* unit=ps */
 315         trwt_mclk = 2;
 316         twrt_mclk = 1;
 317         act_pd_exit_mclk = picos_to_mclk(txp);
 318         pre_pd_exit_mclk = act_pd_exit_mclk;
 319         /*
 320          * MRS_CYC = max(tMRD, tMOD)
 321          * tMRD = 8nCK, tMOD = max(24nCK, 15ns)
 322          */
 323         tmrd_mclk = max(24U, picos_to_mclk(15000));
 324 #elif defined(CONFIG_SYS_FSL_DDR3)
 325         unsigned int data_rate = get_ddr_freq(0);
 326         int txp;
 327         unsigned int ip_rev;
 328         int odt_overlap;
 329         /*
 330          * (tXARD and tXARDS). Empirical?
 331          * The DDR3 spec has not tXARD,
 332          * we use the tXP instead of it.
 333          * tXP=max(3nCK, 7.5ns) for DDR3-800, 1066
 334          *     max(3nCK, 6ns) for DDR3-1333, 1600, 1866, 2133
 335          * spec has not the tAXPD, we use
 336          * tAXPD=1, need design to confirm.
 337          */
 338         txp = max((int)mclk_ps * 3, (mclk_ps > 1540 ? 7500 : 6000));
 339
 340         ip_rev = fsl_ddr_get_version();
 341         if (ip_rev >= 0x40700) {
 342                 /*
 343                  * MRS_CYC = max(tMRD, tMOD)
 344                  * tMRD = 4nCK (8nCK for RDIMM)
 345                  * tMOD = max(12nCK, 15ns)
 346                  */
 347                 tmrd_mclk = max((unsigned int)12, picos_to_mclk(15000));
 348         } else {
 349                 /*
 350                  * MRS_CYC = tMRD
 351                  * tMRD = 4nCK (8nCK for RDIMM)
 352                  */
 353                 if (popts->registered_dimm_en)
 354                         tmrd_mclk = 8;
 355                 else
 356                         tmrd_mclk = 4;
 357         }
 358
 359         /* set the turnaround time */
 360
 361         /*
 362          * for single quad-rank DIMM and two-slot DIMMs
 363          * to avoid ODT overlap
 364          */
 365         odt_overlap = avoid_odt_overlap(dimm_params);
 366         switch (odt_overlap) {
 367         case 2:
 368                 twwt_mclk = 2;
 369                 trrt_mclk = 1;
 370                 break;
 371         case 1:
 372                 twwt_mclk = 1;
 373                 trrt_mclk = 0;
 374                 break;
 375         default:
 376                 break;
 377         }
 378
 379         /* for faster clock, need more time for data setup */
 380         trwt_mclk = (data_rate/1000000 > 1800) ? 2 : 1;
 381
 382         if ((data_rate/1000000 > 1150) || (popts->memctl_interleaving))
 383                 twrt_mclk = 1;
 384
 385         if (popts->dynamic_power == 0) {        /* powerdown is not used */
 386                 act_pd_exit_mclk = 1;
 387                 pre_pd_exit_mclk = 1;
 388                 taxpd_mclk = 1;
 389         } else {
 390                 /* act_pd_exit_mclk = tXARD, see above */
 391                 act_pd_exit_mclk = picos_to_mclk(txp);
 392                 /* Mode register MR0[A12] is '1' - fast exit */
 393                 pre_pd_exit_mclk = act_pd_exit_mclk;
 394                 taxpd_mclk = 1;
 395         }
 396 #else /* CONFIG_SYS_FSL_DDR2 */
 397         /*
 398          * (tXARD and tXARDS). Empirical?
 399          * tXARD = 2 for DDR2
 400          * tXP=2
 401          * tAXPD=8
 402          */
 403         act_pd_exit_mclk = 2;
 404         pre_pd_exit_mclk = 2;
 405         taxpd_mclk = 8;
 406         tmrd_mclk = 2;
 407 #endif
 408
 409         if (popts->trwt_override)
 410                 trwt_mclk = popts->trwt;
 411
 412         ddr->timing_cfg_0 = (0
 413                 | ((trwt_mclk & 0x3) << 30)     /* RWT */
 414                 | ((twrt_mclk & 0x3) << 28)     /* WRT */
 415                 | ((trrt_mclk & 0x3) << 26)     /* RRT */
 416                 | ((twwt_mclk & 0x3) << 24)     /* WWT */
 417                 | ((act_pd_exit_mclk & 0xf) << 20)  /* ACT_PD_EXIT */
 418                 | ((pre_pd_exit_mclk & 0xF) << 16)  /* PRE_PD_EXIT */
 419                 | ((taxpd_mclk & 0xf) << 8)     /* ODT_PD_EXIT */
 420                 | ((tmrd_mclk & 0x1f) << 0)     /* MRS_CYC */
 421                 );
 422         debug("FSLDDR: timing_cfg_0 = 0x%08x\n", ddr->timing_cfg_0);
 423 }
 424 #endif  /* !defined(CONFIG_SYS_FSL_DDR1) */
 425
 426 /* DDR SDRAM Timing Configuration 3 (TIMING_CFG_3) */
 427 static void set_timing_cfg_3(fsl_ddr_cfg_regs_t *ddr,
 428                                const memctl_options_t *popts,
 429                                const common_timing_params_t *common_dimm,
 430                                unsigned int cas_latency,
 431                                unsigned int additive_latency)
 432 {
 433         /* Extended precharge to activate interval (tRP) */
 434         unsigned int ext_pretoact = 0;
 435         /* Extended Activate to precharge interval (tRAS) */
 436         unsigned int ext_acttopre = 0;
 437         /* Extended activate to read/write interval (tRCD) */
 438         unsigned int ext_acttorw = 0;
 439         /* Extended refresh recovery time (tRFC) */
 440         unsigned int ext_refrec;
 441         /* Extended MCAS latency from READ cmd */
 442         unsigned int ext_caslat = 0;
 443         /* Extended additive latency */
 444         unsigned int ext_add_lat = 0;
 445         /* Extended last data to precharge interval (tWR) */
 446         unsigned int ext_wrrec = 0;
 447         /* Control Adjust */
 448         unsigned int cntl_adj = 0;
 449
 450         ext_pretoact = picos_to_mclk(common_dimm->trp_ps) >> 4;
 451         ext_acttopre = picos_to_mclk(common_dimm->tras_ps) >> 4;
 452         ext_acttorw = picos_to_mclk(common_dimm->trcd_ps) >> 4;
 453         ext_caslat = (2 * cas_latency - 1) >> 4;
 454         ext_add_lat = additive_latency >> 4;
 455 #ifdef CONFIG_SYS_FSL_DDR4
 456         ext_refrec = (picos_to_mclk(common_dimm->trfc1_ps) - 8) >> 4;
 457 #else
 458         ext_refrec = (picos_to_mclk(common_dimm->trfc_ps) - 8) >> 4;
 459         /* ext_wrrec only deals with 16 clock and above, or 14 with OTF */
 460 #endif
 461         ext_wrrec = (picos_to_mclk(common_dimm->twr_ps) +
 462                 (popts->otf_burst_chop_en ? 2 : 0)) >> 4;
 463
 464         ddr->timing_cfg_3 = (0
 465                 | ((ext_pretoact & 0x1) << 28)
 466                 | ((ext_acttopre & 0x3) << 24)
 467                 | ((ext_acttorw & 0x1) << 22)
 468                 | ((ext_refrec & 0x1F) << 16)
 469                 | ((ext_caslat & 0x3) << 12)
 470                 | ((ext_add_lat & 0x1) << 10)
 471                 | ((ext_wrrec & 0x1) << 8)
 472                 | ((cntl_adj & 0x7) << 0)
 473                 );
 474         debug("FSLDDR: timing_cfg_3 = 0x%08x\n", ddr->timing_cfg_3);
 475 }
 476
 477 /* DDR SDRAM Timing Configuration 1 (TIMING_CFG_1) */
 478 static void set_timing_cfg_1(fsl_ddr_cfg_regs_t *ddr,
 479                                const memctl_options_t *popts,
 480                                const common_timing_params_t *common_dimm,
 481                                unsigned int cas_latency)
 482 {
 483         /* Precharge-to-activate interval (tRP) */
 484         unsigned char pretoact_mclk;
 485         /* Activate to precharge interval (tRAS) */
 486         unsigned char acttopre_mclk;
 487         /*  Activate to read/write interval (tRCD) */
 488         unsigned char acttorw_mclk;
 489         /* CASLAT */
 490         unsigned char caslat_ctrl;
 491         /*  Refresh recovery time (tRFC) ; trfc_low */
 492         unsigned char refrec_ctrl;
 493         /* Last data to precharge minimum interval (tWR) */
 494         unsigned char wrrec_mclk;
 495         /* Activate-to-activate interval (tRRD) */
 496         unsigned char acttoact_mclk;
 497         /* Last write data pair to read command issue interval (tWTR) */
 498         unsigned char wrtord_mclk;
 499 #ifdef CONFIG_SYS_FSL_DDR4
 500         /* DDR4 supports 10, 12, 14, 16, 18, 20, 24 */
 501         static const u8 wrrec_table[] = {
 502                 10, 10, 10, 10, 10,
 503                 10, 10, 10, 10, 10,
 504                 12, 12, 14, 14, 16,
 505                 16, 18, 18, 20, 20,
 506                 24, 24, 24, 24};
 507 #else
 508         /* DDR_SDRAM_MODE doesn't support 9,11,13,15 */
 509         static const u8 wrrec_table[] = {
 510                 1, 2, 3, 4, 5, 6, 7, 8, 10, 10, 12, 12, 14, 14, 0, 0};
 511 #endif
 512
 513         pretoact_mclk = picos_to_mclk(common_dimm->trp_ps);
 514         acttopre_mclk = picos_to_mclk(common_dimm->tras_ps);
 515         acttorw_mclk = picos_to_mclk(common_dimm->trcd_ps);
 516
 517         /*
 518          * Translate CAS Latency to a DDR controller field value:
 519          *
 520          *      CAS Lat DDR I   DDR II  Ctrl
 521          *      Clocks  SPD Bit SPD Bit Value
 522          *      ------- ------- ------- -----
 523          *      1.0     0               0001
 524          *      1.5     1               0010
 525          *      2.0     2       2       0011
 526          *      2.5     3               0100
 527          *      3.0     4       3       0101
 528          *      3.5     5               0110
 529          *      4.0             4       0111
 530          *      4.5                     1000
 531          *      5.0             5       1001
 532          */
 533 #if defined(CONFIG_SYS_FSL_DDR1)
 534         caslat_ctrl = (cas_latency + 1) & 0x07;
 535 #elif defined(CONFIG_SYS_FSL_DDR2)
 536         caslat_ctrl = 2 * cas_latency - 1;
 537 #else
 538         /*
 539          * if the CAS latency more than 8 cycle,
 540          * we need set extend bit for it at
 541          * TIMING_CFG_3[EXT_CASLAT]
 542          */
 543         if (fsl_ddr_get_version() <= 0x40400)
 544                 caslat_ctrl = 2 * cas_latency - 1;
 545         else
 546                 caslat_ctrl = (cas_latency - 1) << 1;
 547 #endif
 548
 549 #ifdef CONFIG_SYS_FSL_DDR4
 550         refrec_ctrl = picos_to_mclk(common_dimm->trfc1_ps) - 8;
 551         wrrec_mclk = picos_to_mclk(common_dimm->twr_ps);
 552         acttoact_mclk = max(picos_to_mclk(common_dimm->trrds_ps), 4U);
 553         wrtord_mclk = max(2U, picos_to_mclk(2500));
 554         if ((wrrec_mclk < 1) || (wrrec_mclk > 24))
 555                 printf("Error: WRREC doesn't support %d clocks\n", wrrec_mclk);
 556         else
 557                 wrrec_mclk = wrrec_table[wrrec_mclk - 1];
 558 #else
 559         refrec_ctrl = picos_to_mclk(common_dimm->trfc_ps) - 8;
 560         wrrec_mclk = picos_to_mclk(common_dimm->twr_ps);
 561         acttoact_mclk = picos_to_mclk(common_dimm->trrd_ps);
 562         wrtord_mclk = picos_to_mclk(common_dimm->twtr_ps);
 563         if ((wrrec_mclk < 1) || (wrrec_mclk > 16))
 564                 printf("Error: WRREC doesn't support %d clocks\n", wrrec_mclk);
 565         else
 566                 wrrec_mclk = wrrec_table[wrrec_mclk - 1];
 567 #endif
 568         if (popts->otf_burst_chop_en)
 569                 wrrec_mclk += 2;
 570
 571         /*
 572          * JEDEC has min requirement for tRRD
 573          */
 574 #if defined(CONFIG_SYS_FSL_DDR3)
 575         if (acttoact_mclk < 4)
 576                 acttoact_mclk = 4;
 577 #endif
 578         /*
 579          * JEDEC has some min requirements for tWTR
 580          */
 581 #if defined(CONFIG_SYS_FSL_DDR2)
 582         if (wrtord_mclk < 2)
 583                 wrtord_mclk = 2;
 584 #elif defined(CONFIG_SYS_FSL_DDR3)
 585         if (wrtord_mclk < 4)
 586                 wrtord_mclk = 4;
 587 #endif
 588         if (popts->otf_burst_chop_en)
 589                 wrtord_mclk += 2;
 590
 591         ddr->timing_cfg_1 = (0
 592                 | ((pretoact_mclk & 0x0F) << 28)
 593                 | ((acttopre_mclk & 0x0F) << 24)
 594                 | ((acttorw_mclk & 0xF) << 20)
 595                 | ((caslat_ctrl & 0xF) << 16)
 596                 | ((refrec_ctrl & 0xF) << 12)
 597                 | ((wrrec_mclk & 0x0F) << 8)
 598                 | ((acttoact_mclk & 0x0F) << 4)
 599                 | ((wrtord_mclk & 0x0F) << 0)
 600                 );
 601         debug("FSLDDR: timing_cfg_1 = 0x%08x\n", ddr->timing_cfg_1);
 602 }
 603
 604 /* DDR SDRAM Timing Configuration 2 (TIMING_CFG_2) */
 605 static void set_timing_cfg_2(fsl_ddr_cfg_regs_t *ddr,
 606                                const memctl_options_t *popts,
 607                                const common_timing_params_t *common_dimm,
 608                                unsigned int cas_latency,
 609                                unsigned int additive_latency)
 610 {
 611         /* Additive latency */
 612         unsigned char add_lat_mclk;
 613         /* CAS-to-preamble override */
 614         unsigned short cpo;
 615         /* Write latency */
 616         unsigned char wr_lat;
 617         /*  Read to precharge (tRTP) */
 618         unsigned char rd_to_pre;
 619         /* Write command to write data strobe timing adjustment */
 620         unsigned char wr_data_delay;
 621         /* Minimum CKE pulse width (tCKE) */
 622         unsigned char cke_pls;
 623         /* Window for four activates (tFAW) */
 624         unsigned short four_act;
 625 #ifdef CONFIG_SYS_FSL_DDR3
 626         const unsigned int mclk_ps = get_memory_clk_period_ps();
 627 #endif
 628
 629         /* FIXME add check that this must be less than acttorw_mclk */
 630         add_lat_mclk = additive_latency;
 631         cpo = popts->cpo_override;
 632
 633 #if defined(CONFIG_SYS_FSL_DDR1)
 634         /*
 635          * This is a lie.  It should really be 1, but if it is
 636          * set to 1, bits overlap into the old controller's
 637          * otherwise unused ACSM field.  If we leave it 0, then
 638          * the HW will magically treat it as 1 for DDR 1.  Oh Yea.
 639          */
 640         wr_lat = 0;
 641 #elif defined(CONFIG_SYS_FSL_DDR2)
 642         wr_lat = cas_latency - 1;
 643 #else
 644         wr_lat = compute_cas_write_latency();
 645 #endif
 646
 647 #ifdef CONFIG_SYS_FSL_DDR4
 648         rd_to_pre = picos_to_mclk(7500);
 649 #else
 650         rd_to_pre = picos_to_mclk(common_dimm->trtp_ps);
 651 #endif
 652         /*
 653          * JEDEC has some min requirements for tRTP
 654          */
 655 #if defined(CONFIG_SYS_FSL_DDR2)
 656         if (rd_to_pre  < 2)
 657                 rd_to_pre  = 2;
 658 #elif defined(CONFIG_SYS_FSL_DDR3) || defined(CONFIG_SYS_FSL_DDR4)
 659         if (rd_to_pre < 4)
 660                 rd_to_pre = 4;
 661 #endif
 662         if (popts->otf_burst_chop_en)
 663                 rd_to_pre += 2; /* according to UM */
 664
 665         wr_data_delay = popts->write_data_delay;
 666 #ifdef CONFIG_SYS_FSL_DDR4
 667         cpo = 0;
 668         cke_pls = max(3U, picos_to_mclk(5000));
 669 #elif defined(CONFIG_SYS_FSL_DDR3)
 670         /*
 671          * cke pulse = max(3nCK, 7.5ns) for DDR3-800
 672          *             max(3nCK, 5.625ns) for DDR3-1066, 1333
 673          *             max(3nCK, 5ns) for DDR3-1600, 1866, 2133
 674          */
 675         cke_pls = max(3U, picos_to_mclk(mclk_ps > 1870 ? 7500 :
 676                                        (mclk_ps > 1245 ? 5625 : 5000)));
 677 #else
 678         cke_pls = FSL_DDR_MIN_TCKE_PULSE_WIDTH_DDR;
 679 #endif
 680         four_act = picos_to_mclk(popts->tfaw_window_four_activates_ps);
 681
 682         ddr->timing_cfg_2 = (0
 683                 | ((add_lat_mclk & 0xf) << 28)
 684                 | ((cpo & 0x1f) << 23)
 685                 | ((wr_lat & 0xf) << 19)
 686                 | ((wr_lat & 0x10) << 14)
 687                 | ((rd_to_pre & RD_TO_PRE_MASK) << RD_TO_PRE_SHIFT)
 688                 | ((wr_data_delay & WR_DATA_DELAY_MASK) << WR_DATA_DELAY_SHIFT)
 689                 | ((cke_pls & 0x7) << 6)
 690                 | ((four_act & 0x3f) << 0)
 691                 );
 692         debug("FSLDDR: timing_cfg_2 = 0x%08x\n", ddr->timing_cfg_2);
 693 }
 694
 695 /* DDR SDRAM Register Control Word */
 696 static void set_ddr_sdram_rcw(fsl_ddr_cfg_regs_t *ddr,
 697                                const memctl_options_t *popts,
 698                                const common_timing_params_t *common_dimm)
 699 {
 700         if (common_dimm->all_dimms_registered &&
 701             !common_dimm->all_dimms_unbuffered) {
 702                 if (popts->rcw_override) {
 703                         ddr->ddr_sdram_rcw_1 = popts->rcw_1;
 704                         ddr->ddr_sdram_rcw_2 = popts->rcw_2;
 705                 } else {
 706                         ddr->ddr_sdram_rcw_1 =
 707                                 common_dimm->rcw[0] << 28 | \
 708                                 common_dimm->rcw[1] << 24 | \
 709                                 common_dimm->rcw[2] << 20 | \
 710                                 common_dimm->rcw[3] << 16 | \
 711                                 common_dimm->rcw[4] << 12 | \
 712                                 common_dimm->rcw[5] << 8 | \
 713                                 common_dimm->rcw[6] << 4 | \
 714                                 common_dimm->rcw[7];
 715                         ddr->ddr_sdram_rcw_2 =
 716                                 common_dimm->rcw[8] << 28 | \
 717                                 common_dimm->rcw[9] << 24 | \
 718                                 common_dimm->rcw[10] << 20 | \
 719                                 common_dimm->rcw[11] << 16 | \
 720                                 common_dimm->rcw[12] << 12 | \
 721                                 common_dimm->rcw[13] << 8 | \
 722                                 common_dimm->rcw[14] << 4 | \
 723                                 common_dimm->rcw[15];
 724                 }
 725                 debug("FSLDDR: ddr_sdram_rcw_1 = 0x%08x\n", ddr->ddr_sdram_rcw_1);
 726                 debug("FSLDDR: ddr_sdram_rcw_2 = 0x%08x\n", ddr->ddr_sdram_rcw_2);
 727         }
 728 }
 729
 730 /* DDR SDRAM control configuration (DDR_SDRAM_CFG) */
 731 static void set_ddr_sdram_cfg(fsl_ddr_cfg_regs_t *ddr,
 732                                const memctl_options_t *popts,
 733                                const common_timing_params_t *common_dimm)
 734 {
 735         unsigned int mem_en;            /* DDR SDRAM interface logic enable */
 736         unsigned int sren;              /* Self refresh enable (during sleep) */
 737         unsigned int ecc_en;            /* ECC enable. */
 738         unsigned int rd_en;             /* Registered DIMM enable */
 739         unsigned int sdram_type;        /* Type of SDRAM */
 740         unsigned int dyn_pwr;           /* Dynamic power management mode */
 741         unsigned int dbw;               /* DRAM dta bus width */
 742         unsigned int eight_be = 0;      /* 8-beat burst enable, DDR2 is zero */
 743         unsigned int ncap = 0;          /* Non-concurrent auto-precharge */
 744         unsigned int threet_en;         /* Enable 3T timing */
 745         unsigned int twot_en;           /* Enable 2T timing */
 746         unsigned int ba_intlv_ctl;      /* Bank (CS) interleaving control */
 747         unsigned int x32_en = 0;        /* x32 enable */
 748         unsigned int pchb8 = 0;         /* precharge bit 8 enable */
 749         unsigned int hse;               /* Global half strength override */
 750         unsigned int acc_ecc_en = 0;    /* Accumulated ECC enable */
 751         unsigned int mem_halt = 0;      /* memory controller halt */
 752         unsigned int bi = 0;            /* Bypass initialization */
 753
 754         mem_en = 1;
 755         sren = popts->self_refresh_in_sleep;
 756         if (common_dimm->all_dimms_ecc_capable) {
 757                 /* Allow setting of ECC only if all DIMMs are ECC. */
 758                 ecc_en = popts->ecc_mode;
 759         } else {
 760                 ecc_en = 0;
 761         }
 762
 763         if (common_dimm->all_dimms_registered &&
 764             !common_dimm->all_dimms_unbuffered) {
 765                 rd_en = 1;
 766                 twot_en = 0;
 767         } else {
 768                 rd_en = 0;
 769                 twot_en = popts->twot_en;
 770         }
 771
 772         sdram_type = CONFIG_FSL_SDRAM_TYPE;
 773
 774         dyn_pwr = popts->dynamic_power;
 775         dbw = popts->data_bus_width;
 776         /* 8-beat burst enable DDR-III case
 777          * we must clear it when use the on-the-fly mode,
 778          * must set it when use the 32-bits bus mode.
 779          */
 780         if ((sdram_type == SDRAM_TYPE_DDR3) ||
 781             (sdram_type == SDRAM_TYPE_DDR4)) {
 782                 if (popts->burst_length == DDR_BL8)
 783                         eight_be = 1;
 784                 if (popts->burst_length == DDR_OTF)
 785                         eight_be = 0;
 786                 if (dbw == 0x1)
 787                         eight_be = 1;
 788         }
 789
 790         threet_en = popts->threet_en;
 791         ba_intlv_ctl = popts->ba_intlv_ctl;
 792         hse = popts->half_strength_driver_enable;
 793
 794         /* set when ddr bus width < 64 */
 795         acc_ecc_en = (dbw != 0 && ecc_en == 1) ? 1 : 0;
 796
 797         ddr->ddr_sdram_cfg = (0
 798                         | ((mem_en & 0x1) << 31)
 799                         | ((sren & 0x1) << 30)
 800                         | ((ecc_en & 0x1) << 29)
 801                         | ((rd_en & 0x1) << 28)
 802                         | ((sdram_type & 0x7) << 24)
 803                         | ((dyn_pwr & 0x1) << 21)
 804                         | ((dbw & 0x3) << 19)
 805                         | ((eight_be & 0x1) << 18)
 806                         | ((ncap & 0x1) << 17)
 807                         | ((threet_en & 0x1) << 16)
 808                         | ((twot_en & 0x1) << 15)
 809                         | ((ba_intlv_ctl & 0x7F) << 8)
 810                         | ((x32_en & 0x1) << 5)
 811                         | ((pchb8 & 0x1) << 4)
 812                         | ((hse & 0x1) << 3)
 813                         | ((acc_ecc_en & 0x1) << 2)
 814                         | ((mem_halt & 0x1) << 1)
 815                         | ((bi & 0x1) << 0)
 816                         );
 817         debug("FSLDDR: ddr_sdram_cfg = 0x%08x\n", ddr->ddr_sdram_cfg);
 818 }
 819
 820 /* DDR SDRAM control configuration 2 (DDR_SDRAM_CFG_2) */
 821 static void set_ddr_sdram_cfg_2(fsl_ddr_cfg_regs_t *ddr,
 822                                const memctl_options_t *popts,
 823                                const unsigned int unq_mrs_en)
 824 {
 825         unsigned int frc_sr = 0;        /* Force self refresh */
 826         unsigned int sr_ie = 0;         /* Self-refresh interrupt enable */
 827         unsigned int odt_cfg = 0;       /* ODT configuration */
 828         unsigned int num_pr;            /* Number of posted refreshes */
 829         unsigned int slow = 0;          /* DDR will be run less than 1250 */
 830         unsigned int x4_en = 0;         /* x4 DRAM enable */
 831         unsigned int obc_cfg;           /* On-The-Fly Burst Chop Cfg */
 832         unsigned int ap_en;             /* Address Parity Enable */
 833         unsigned int d_init;            /* DRAM data initialization */
 834         unsigned int rcw_en = 0;        /* Register Control Word Enable */
 835         unsigned int md_en = 0;         /* Mirrored DIMM Enable */
 836         unsigned int qd_en = 0;         /* quad-rank DIMM Enable */
 837         int i;
 838 #ifndef CONFIG_SYS_FSL_DDR4
 839         unsigned int dll_rst_dis = 1;   /* DLL reset disable */
 840         unsigned int dqs_cfg;           /* DQS configuration */
 841
 842         dqs_cfg = popts->dqs_config;
 843 #endif
 844         for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
 845                 if (popts->cs_local_opts[i].odt_rd_cfg
 846                         || popts->cs_local_opts[i].odt_wr_cfg) {
 847                         odt_cfg = SDRAM_CFG2_ODT_ONLY_READ;
 848                         break;
 849                 }
 850         }
 851
 852         num_pr = 1;     /* Make this configurable */
 853
 854         /*
 855          * 8572 manual says
 856          *     {TIMING_CFG_1[PRETOACT]
 857          *      + [DDR_SDRAM_CFG_2[NUM_PR]
 858          *        * ({EXT_REFREC || REFREC} + 8 + 2)]}
 859          *      << DDR_SDRAM_INTERVAL[REFINT]
 860          */
 861 #if defined(CONFIG_SYS_FSL_DDR3) || defined(CONFIG_SYS_FSL_DDR4)
 862         obc_cfg = popts->otf_burst_chop_en;
 863 #else
 864         obc_cfg = 0;
 865 #endif
 866
 867 #if (CONFIG_SYS_FSL_DDR_VER >= FSL_DDR_VER_4_7)
 868         slow = get_ddr_freq(0) < 1249000000;
 869 #endif
 870
 871         if (popts->registered_dimm_en) {
 872                 rcw_en = 1;
 873                 ap_en = popts->ap_en;
 874         } else {
 875                 ap_en = 0;
 876         }
 877
 878         x4_en = popts->x4_en ? 1 : 0;
 879
 880 #if defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
 881         /* Use the DDR controller to auto initialize memory. */
 882         d_init = popts->ecc_init_using_memctl;
 883         ddr->ddr_data_init = CONFIG_MEM_INIT_VALUE;
 884         debug("DDR: ddr_data_init = 0x%08x\n", ddr->ddr_data_init);
 885 #else
 886         /* Memory will be initialized via DMA, or not at all. */
 887         d_init = 0;
 888 #endif
 889
 890 #if defined(CONFIG_SYS_FSL_DDR3) || defined(CONFIG_SYS_FSL_DDR4)
 891         md_en = popts->mirrored_dimm;
 892 #endif
 893         qd_en = popts->quad_rank_present ? 1 : 0;
 894         ddr->ddr_sdram_cfg_2 = (0
 895                 | ((frc_sr & 0x1) << 31)
 896                 | ((sr_ie & 0x1) << 30)
 897 #ifndef CONFIG_SYS_FSL_DDR4
 898                 | ((dll_rst_dis & 0x1) << 29)
 899                 | ((dqs_cfg & 0x3) << 26)
 900 #endif
 901                 | ((odt_cfg & 0x3) << 21)
 902                 | ((num_pr & 0xf) << 12)
 903                 | ((slow & 1) << 11)
 904                 | (x4_en << 10)
 905                 | (qd_en << 9)
 906                 | (unq_mrs_en << 8)
 907                 | ((obc_cfg & 0x1) << 6)
 908                 | ((ap_en & 0x1) << 5)
 909                 | ((d_init & 0x1) << 4)
 910                 | ((rcw_en & 0x1) << 2)
 911                 | ((md_en & 0x1) << 0)
 912                 );
 913         debug("FSLDDR: ddr_sdram_cfg_2 = 0x%08x\n", ddr->ddr_sdram_cfg_2);
 914 }
 915
 916 #ifdef CONFIG_SYS_FSL_DDR4
 917 /* DDR SDRAM Mode configuration 2 (DDR_SDRAM_MODE_2) */
 918 static void set_ddr_sdram_mode_2(fsl_ddr_cfg_regs_t *ddr,
 919                                 const memctl_options_t *popts,
 920                                 const common_timing_params_t *common_dimm,
 921                                 const unsigned int unq_mrs_en)
 922 {
 923         unsigned short esdmode2 = 0;    /* Extended SDRAM mode 2 */
 924         unsigned short esdmode3 = 0;    /* Extended SDRAM mode 3 */
 925         int i;
 926         unsigned int wr_crc = 0;        /* Disable */
 927         unsigned int rtt_wr = 0;        /* Rtt_WR - dynamic ODT off */
 928         unsigned int srt = 0;   /* self-refresh temerature, normal range */
 929         unsigned int cwl = compute_cas_write_latency() - 9;
 930         unsigned int mpr = 0;   /* serial */
 931         unsigned int wc_lat;
 932         const unsigned int mclk_ps = get_memory_clk_period_ps();
 933
 934         if (popts->rtt_override)
 935                 rtt_wr = popts->rtt_wr_override_value;
 936         else
 937                 rtt_wr = popts->cs_local_opts[0].odt_rtt_wr;
 938
 939         if (common_dimm->extended_op_srt)
 940                 srt = common_dimm->extended_op_srt;
 941
 942         esdmode2 = (0
 943                 | ((wr_crc & 0x1) << 12)
 944                 | ((rtt_wr & 0x3) << 9)
 945                 | ((srt & 0x3) << 6)
 946                 | ((cwl & 0x7) << 3));
 947
 948         if (mclk_ps >= 1250)
 949                 wc_lat = 0;
 950         else if (mclk_ps >= 833)
 951                 wc_lat = 1;
 952         else
 953                 wc_lat = 2;
 954
 955         esdmode3 = (0
 956                 | ((mpr & 0x3) << 11)
 957                 | ((wc_lat & 0x3) << 9));
 958
 959         ddr->ddr_sdram_mode_2 = (0
 960                                  | ((esdmode2 & 0xFFFF) << 16)
 961                                  | ((esdmode3 & 0xFFFF) << 0)
 962                                  );
 963         debug("FSLDDR: ddr_sdram_mode_2 = 0x%08x\n", ddr->ddr_sdram_mode_2);
 964
 965         if (unq_mrs_en) {       /* unique mode registers are supported */
 966                 for (i = 1; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
 967                         if (popts->rtt_override)
 968                                 rtt_wr = popts->rtt_wr_override_value;
 969                         else
 970                                 rtt_wr = popts->cs_local_opts[i].odt_rtt_wr;
 971
 972                         esdmode2 &= 0xF9FF;     /* clear bit 10, 9 */
 973                         esdmode2 |= (rtt_wr & 0x3) << 9;
 974                         switch (i) {
 975                         case 1:
 976                                 ddr->ddr_sdram_mode_4 = (0
 977                                         | ((esdmode2 & 0xFFFF) << 16)
 978                                         | ((esdmode3 & 0xFFFF) << 0)
 979                                         );
 980                                 break;
 981                         case 2:
 982                                 ddr->ddr_sdram_mode_6 = (0
 983                                         | ((esdmode2 & 0xFFFF) << 16)
 984                                         | ((esdmode3 & 0xFFFF) << 0)
 985                                         );
 986                                 break;
 987                         case 3:
 988                                 ddr->ddr_sdram_mode_8 = (0
 989                                         | ((esdmode2 & 0xFFFF) << 16)
 990                                         | ((esdmode3 & 0xFFFF) << 0)
 991                                         );
 992                                 break;
 993                         }
 994                 }
 995                 debug("FSLDDR: ddr_sdram_mode_4 = 0x%08x\n",
 996                       ddr->ddr_sdram_mode_4);
 997                 debug("FSLDDR: ddr_sdram_mode_6 = 0x%08x\n",
 998                       ddr->ddr_sdram_mode_6);
 999                 debug("FSLDDR: ddr_sdram_mode_8 = 0x%08x\n",
1000                       ddr->ddr_sdram_mode_8);
1001         }
1002 }
1003 #elif defined(CONFIG_SYS_FSL_DDR3)
1004 /* DDR SDRAM Mode configuration 2 (DDR_SDRAM_MODE_2) */
1005 static void set_ddr_sdram_mode_2(fsl_ddr_cfg_regs_t *ddr,
1006                                 const memctl_options_t *popts,
1007                                 const common_timing_params_t *common_dimm,
1008                                 const unsigned int unq_mrs_en)
1009 {
1010         unsigned short esdmode2 = 0;    /* Extended SDRAM mode 2 */
1011         unsigned short esdmode3 = 0;    /* Extended SDRAM mode 3 */
1012         int i;
1013         unsigned int rtt_wr = 0;        /* Rtt_WR - dynamic ODT off */
1014         unsigned int srt = 0;   /* self-refresh temerature, normal range */
1015         unsigned int asr = 0;   /* auto self-refresh disable */
1016         unsigned int cwl = compute_cas_write_latency() - 5;
1017         unsigned int pasr = 0;  /* partial array self refresh disable */
1018
1019         if (popts->rtt_override)
1020                 rtt_wr = popts->rtt_wr_override_value;
1021         else
1022                 rtt_wr = popts->cs_local_opts[0].odt_rtt_wr;
1023
1024         if (common_dimm->extended_op_srt)
1025                 srt = common_dimm->extended_op_srt;
1026
1027         esdmode2 = (0
1028                 | ((rtt_wr & 0x3) << 9)
1029                 | ((srt & 0x1) << 7)
1030                 | ((asr & 0x1) << 6)
1031                 | ((cwl & 0x7) << 3)
1032                 | ((pasr & 0x7) << 0));
1033         ddr->ddr_sdram_mode_2 = (0
1034                                  | ((esdmode2 & 0xFFFF) << 16)
1035                                  | ((esdmode3 & 0xFFFF) << 0)
1036                                  );
1037         debug("FSLDDR: ddr_sdram_mode_2 = 0x%08x\n", ddr->ddr_sdram_mode_2);
1038
1039         if (unq_mrs_en) {       /* unique mode registers are supported */
1040                 for (i = 1; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
1041                         if (popts->rtt_override)
1042                                 rtt_wr = popts->rtt_wr_override_value;
1043                         else
1044                                 rtt_wr = popts->cs_local_opts[i].odt_rtt_wr;
1045
1046                         esdmode2 &= 0xF9FF;     /* clear bit 10, 9 */
1047                         esdmode2 |= (rtt_wr & 0x3) << 9;
1048                         switch (i) {
1049                         case 1:
1050                                 ddr->ddr_sdram_mode_4 = (0
1051                                         | ((esdmode2 & 0xFFFF) << 16)
1052                                         | ((esdmode3 & 0xFFFF) << 0)
1053                                         );
1054                                 break;
1055                         case 2:
1056                                 ddr->ddr_sdram_mode_6 = (0
1057                                         | ((esdmode2 & 0xFFFF) << 16)
1058                                         | ((esdmode3 & 0xFFFF) << 0)
1059                                         );
1060                                 break;
1061                         case 3:
1062                                 ddr->ddr_sdram_mode_8 = (0
1063                                         | ((esdmode2 & 0xFFFF) << 16)
1064                                         | ((esdmode3 & 0xFFFF) << 0)
1065                                         );
1066                                 break;
1067                         }
1068                 }
1069                 debug("FSLDDR: ddr_sdram_mode_4 = 0x%08x\n",
1070                         ddr->ddr_sdram_mode_4);
1071                 debug("FSLDDR: ddr_sdram_mode_6 = 0x%08x\n",
1072                         ddr->ddr_sdram_mode_6);
1073                 debug("FSLDDR: ddr_sdram_mode_8 = 0x%08x\n",
1074                         ddr->ddr_sdram_mode_8);
1075         }
1076 }
1077
1078 #else /* for DDR2 and DDR1 */
1079 /* DDR SDRAM Mode configuration 2 (DDR_SDRAM_MODE_2) */
1080 static void set_ddr_sdram_mode_2(fsl_ddr_cfg_regs_t *ddr,
1081                                 const memctl_options_t *popts,
1082                                 const common_timing_params_t *common_dimm,
1083                                 const unsigned int unq_mrs_en)
1084 {
1085         unsigned short esdmode2 = 0;    /* Extended SDRAM mode 2 */
1086         unsigned short esdmode3 = 0;    /* Extended SDRAM mode 3 */
1087
1088         ddr->ddr_sdram_mode_2 = (0
1089                                  | ((esdmode2 & 0xFFFF) << 16)
1090                                  | ((esdmode3 & 0xFFFF) << 0)
1091                                  );
1092         debug("FSLDDR: ddr_sdram_mode_2 = 0x%08x\n", ddr->ddr_sdram_mode_2);
1093 }
1094 #endif
1095
1096 #ifdef CONFIG_SYS_FSL_DDR4
1097 /* DDR SDRAM Mode configuration 9 (DDR_SDRAM_MODE_9) */
1098 static void set_ddr_sdram_mode_9(fsl_ddr_cfg_regs_t *ddr,
1099                                 const memctl_options_t *popts,
1100                                 const common_timing_params_t *common_dimm,
1101                                 const unsigned int unq_mrs_en)
1102 {
1103         int i;
1104         unsigned short esdmode4 = 0;    /* Extended SDRAM mode 4 */
1105         unsigned short esdmode5;        /* Extended SDRAM mode 5 */
1106
1107         esdmode5 = 0x00000400;          /* Data mask enabled */
1108
1109         ddr->ddr_sdram_mode_9 = (0
1110                                  | ((esdmode4 & 0xffff) << 16)
1111                                  | ((esdmode5 & 0xffff) << 0)
1112                                 );
1113         debug("FSLDDR: ddr_sdram_mode_9) = 0x%08x\n", ddr->ddr_sdram_mode_9);
1114         if (unq_mrs_en) {       /* unique mode registers are supported */
1115                 for (i = 1; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
1116                         switch (i) {
1117                         case 1:
1118                                 ddr->ddr_sdram_mode_11 = (0
1119                                         | ((esdmode4 & 0xFFFF) << 16)
1120                                         | ((esdmode5 & 0xFFFF) << 0)
1121                                         );
1122                                 break;
1123                         case 2:
1124                                 ddr->ddr_sdram_mode_13 = (0
1125                                         | ((esdmode4 & 0xFFFF) << 16)
1126                                         | ((esdmode5 & 0xFFFF) << 0)
1127                                         );
1128                                 break;
1129                         case 3:
1130                                 ddr->ddr_sdram_mode_15 = (0
1131                                         | ((esdmode4 & 0xFFFF) << 16)
1132                                         | ((esdmode5 & 0xFFFF) << 0)
1133                                         );
1134                                 break;
1135                         }
1136                 }
1137                 debug("FSLDDR: ddr_sdram_mode_11 = 0x%08x\n",
1138                       ddr->ddr_sdram_mode_11);
1139                 debug("FSLDDR: ddr_sdram_mode_13 = 0x%08x\n",
1140                       ddr->ddr_sdram_mode_13);
1141                 debug("FSLDDR: ddr_sdram_mode_15 = 0x%08x\n",
1142                       ddr->ddr_sdram_mode_15);
1143         }
1144 }
1145
1146 /* DDR SDRAM Mode configuration 10 (DDR_SDRAM_MODE_10) */
1147 static void set_ddr_sdram_mode_10(fsl_ddr_cfg_regs_t *ddr,
1148                                 const memctl_options_t *popts,
1149                                 const common_timing_params_t *common_dimm,
1150                                 const unsigned int unq_mrs_en)
1151 {
1152         int i;
1153         unsigned short esdmode6 = 0;    /* Extended SDRAM mode 6 */
1154         unsigned short esdmode7 = 0;    /* Extended SDRAM mode 7 */
1155         unsigned int tccdl_min = picos_to_mclk(common_dimm->tccdl_ps);
1156
1157         esdmode6 = ((tccdl_min - 4) & 0x7) << 10;
1158
1159         ddr->ddr_sdram_mode_10 = (0
1160                                  | ((esdmode6 & 0xffff) << 16)
1161                                  | ((esdmode7 & 0xffff) << 0)
1162                                 );
1163         debug("FSLDDR: ddr_sdram_mode_10) = 0x%08x\n", ddr->ddr_sdram_mode_10);
1164         if (unq_mrs_en) {       /* unique mode registers are supported */
1165                 for (i = 1; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
1166                         switch (i) {
1167                         case 1:
1168                                 ddr->ddr_sdram_mode_12 = (0
1169                                         | ((esdmode6 & 0xFFFF) << 16)
1170                                         | ((esdmode7 & 0xFFFF) << 0)
1171                                         );
1172                                 break;
1173                         case 2:
1174                                 ddr->ddr_sdram_mode_14 = (0
1175                                         | ((esdmode6 & 0xFFFF) << 16)
1176                                         | ((esdmode7 & 0xFFFF) << 0)
1177                                         );
1178                                 break;
1179                         case 3:
1180                                 ddr->ddr_sdram_mode_16 = (0
1181                                         | ((esdmode6 & 0xFFFF) << 16)
1182                                         | ((esdmode7 & 0xFFFF) << 0)
1183                                         );
1184                                 break;
1185                         }
1186                 }
1187                 debug("FSLDDR: ddr_sdram_mode_12 = 0x%08x\n",
1188                       ddr->ddr_sdram_mode_12);
1189                 debug("FSLDDR: ddr_sdram_mode_14 = 0x%08x\n",
1190                       ddr->ddr_sdram_mode_14);
1191                 debug("FSLDDR: ddr_sdram_mode_16 = 0x%08x\n",
1192                       ddr->ddr_sdram_mode_16);
1193         }
1194 }
1195
1196 #endif
1197
1198 /* DDR SDRAM Interval Configuration (DDR_SDRAM_INTERVAL) */
1199 static void set_ddr_sdram_interval(fsl_ddr_cfg_regs_t *ddr,
1200                                const memctl_options_t *popts,
1201                                const common_timing_params_t *common_dimm)
1202 {
1203         unsigned int refint;    /* Refresh interval */
1204         unsigned int bstopre;   /* Precharge interval */
1205
1206         refint = picos_to_mclk(common_dimm->refresh_rate_ps);
1207
1208         bstopre = popts->bstopre;
1209
1210         /* refint field used 0x3FFF in earlier controllers */
1211         ddr->ddr_sdram_interval = (0
1212                                    | ((refint & 0xFFFF) << 16)
1213                                    | ((bstopre & 0x3FFF) << 0)
1214                                    );
1215         debug("FSLDDR: ddr_sdram_interval = 0x%08x\n", ddr->ddr_sdram_interval);
1216 }
1217
1218 #ifdef CONFIG_SYS_FSL_DDR4
1219 /* DDR SDRAM Mode configuration set (DDR_SDRAM_MODE) */
1220 static void set_ddr_sdram_mode(fsl_ddr_cfg_regs_t *ddr,
1221                                const memctl_options_t *popts,
1222                                const common_timing_params_t *common_dimm,
1223                                unsigned int cas_latency,
1224                                unsigned int additive_latency,
1225                                const unsigned int unq_mrs_en)
1226 {
1227         int i;
1228         unsigned short esdmode;         /* Extended SDRAM mode */
1229         unsigned short sdmode;          /* SDRAM mode */
1230
1231         /* Mode Register - MR1 */
1232         unsigned int qoff = 0;          /* Output buffer enable 0=yes, 1=no */
1233         unsigned int tdqs_en = 0;       /* TDQS Enable: 0=no, 1=yes */
1234         unsigned int rtt;
1235         unsigned int wrlvl_en = 0;      /* Write level enable: 0=no, 1=yes */
1236         unsigned int al = 0;            /* Posted CAS# additive latency (AL) */
1237         unsigned int dic = 0;           /* Output driver impedance, 40ohm */
1238         unsigned int dll_en = 1;        /* DLL Enable  1=Enable (Normal),
1239                                                        0=Disable (Test/Debug) */
1240
1241         /* Mode Register - MR0 */
1242         unsigned int wr = 0;    /* Write Recovery */
1243         unsigned int dll_rst;   /* DLL Reset */
1244         unsigned int mode;      /* Normal=0 or Test=1 */
1245         unsigned int caslat = 4;/* CAS# latency, default set as 6 cycles */
1246         /* BT: Burst Type (0=Nibble Sequential, 1=Interleaved) */
1247         unsigned int bt;
1248         unsigned int bl;        /* BL: Burst Length */
1249
1250         unsigned int wr_mclk;
1251         /* DDR4 support WR 10, 12, 14, 16, 18, 20, 24 */
1252         static const u8 wr_table[] = {
1253                 0, 1, 1, 2, 2, 3, 3, 4, 4, 5, 5, 6, 6, 6, 6};
1254         /* DDR4 support CAS 9, 10, 11, 12, 13, 14, 15, 16, 18, 20, 22, 24 */
1255         static const u8 cas_latency_table[] = {
1256                 0, 1, 2, 3, 4, 5, 6, 7, 8, 8,
1257                 9, 9, 10, 10, 11, 11};
1258
1259         if (popts->rtt_override)
1260                 rtt = popts->rtt_override_value;
1261         else
1262                 rtt = popts->cs_local_opts[0].odt_rtt_norm;
1263
1264         if (additive_latency == (cas_latency - 1))
1265                 al = 1;
1266         if (additive_latency == (cas_latency - 2))
1267                 al = 2;
1268
1269         if (popts->quad_rank_present)
1270                 dic = 1;        /* output driver impedance 240/7 ohm */
1271
1272         /*
1273          * The esdmode value will also be used for writing
1274          * MR1 during write leveling for DDR3, although the
1275          * bits specifically related to the write leveling
1276          * scheme will be handled automatically by the DDR
1277          * controller. so we set the wrlvl_en = 0 here.
1278          */
1279         esdmode = (0
1280                 | ((qoff & 0x1) << 12)
1281                 | ((tdqs_en & 0x1) << 11)
1282                 | ((rtt & 0x7) << 8)
1283                 | ((wrlvl_en & 0x1) << 7)
1284                 | ((al & 0x3) << 3)
1285                 | ((dic & 0x3) << 1)   /* DIC field is split */
1286                 | ((dll_en & 0x1) << 0)
1287                 );
1288
1289         /*
1290          * DLL control for precharge PD
1291          * 0=slow exit DLL off (tXPDLL)
1292          * 1=fast exit DLL on (tXP)
1293          */
1294
1295         wr_mclk = picos_to_mclk(common_dimm->twr_ps);
1296         if (wr_mclk <= 24) {
1297                 wr = wr_table[wr_mclk - 10];
1298         } else {
1299                 printf("Error: unsupported write recovery for mode register wr_mclk = %d\n",
1300                        wr_mclk);
1301         }
1302
1303         dll_rst = 0;    /* dll no reset */
1304         mode = 0;       /* normal mode */
1305
1306         /* look up table to get the cas latency bits */
1307         if (cas_latency >= 9 && cas_latency <= 24)
1308                 caslat = cas_latency_table[cas_latency - 9];
1309         else
1310                 printf("Error: unsupported cas latency for mode register\n");
1311
1312         bt = 0; /* Nibble sequential */
1313
1314         switch (popts->burst_length) {
1315         case DDR_BL8:
1316                 bl = 0;
1317                 break;
1318         case DDR_OTF:
1319                 bl = 1;
1320                 break;
1321         case DDR_BC4:
1322                 bl = 2;
1323                 break;
1324         default:
1325                 printf("Error: invalid burst length of %u specified. ",
1326                        popts->burst_length);
1327                 puts("Defaulting to on-the-fly BC4 or BL8 beats.\n");
1328                 bl = 1;
1329                 break;
1330         }
1331
1332         sdmode = (0
1333                   | ((wr & 0x7) << 9)
1334                   | ((dll_rst & 0x1) << 8)
1335                   | ((mode & 0x1) << 7)
1336                   | (((caslat >> 1) & 0x7) << 4)
1337                   | ((bt & 0x1) << 3)
1338                   | ((caslat & 1) << 2)
1339                   | ((bl & 0x3) << 0)
1340                   );
1341
1342         ddr->ddr_sdram_mode = (0
1343                                | ((esdmode & 0xFFFF) << 16)
1344                                | ((sdmode & 0xFFFF) << 0)
1345                                );
1346
1347         debug("FSLDDR: ddr_sdram_mode = 0x%08x\n", ddr->ddr_sdram_mode);
1348
1349         if (unq_mrs_en) {       /* unique mode registers are supported */
1350                 for (i = 1; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
1351                         if (popts->rtt_override)
1352                                 rtt = popts->rtt_override_value;
1353                         else
1354                                 rtt = popts->cs_local_opts[i].odt_rtt_norm;
1355
1356                         esdmode &= 0xF8FF;      /* clear bit 10,9,8 for rtt */
1357                         esdmode |= (rtt & 0x7) << 8;
1358                         switch (i) {
1359                         case 1:
1360                                 ddr->ddr_sdram_mode_3 = (0
1361                                        | ((esdmode & 0xFFFF) << 16)
1362                                        | ((sdmode & 0xFFFF) << 0)
1363                                        );
1364                                 break;
1365                         case 2:
1366                                 ddr->ddr_sdram_mode_5 = (0
1367                                        | ((esdmode & 0xFFFF) << 16)
1368                                        | ((sdmode & 0xFFFF) << 0)
1369                                        );
1370                                 break;
1371                         case 3:
1372                                 ddr->ddr_sdram_mode_7 = (0
1373                                        | ((esdmode & 0xFFFF) << 16)
1374                                        | ((sdmode & 0xFFFF) << 0)
1375                                        );
1376                                 break;
1377                         }
1378                 }
1379                 debug("FSLDDR: ddr_sdram_mode_3 = 0x%08x\n",
1380                       ddr->ddr_sdram_mode_3);
1381                 debug("FSLDDR: ddr_sdram_mode_5 = 0x%08x\n",
1382                       ddr->ddr_sdram_mode_5);
1383                 debug("FSLDDR: ddr_sdram_mode_5 = 0x%08x\n",
1384                       ddr->ddr_sdram_mode_5);
1385         }
1386 }
1387
1388 #elif defined(CONFIG_SYS_FSL_DDR3)
1389 /* DDR SDRAM Mode configuration set (DDR_SDRAM_MODE) */
1390 static void set_ddr_sdram_mode(fsl_ddr_cfg_regs_t *ddr,
1391                                const memctl_options_t *popts,
1392                                const common_timing_params_t *common_dimm,
1393                                unsigned int cas_latency,
1394                                unsigned int additive_latency,
1395                                const unsigned int unq_mrs_en)
1396 {
1397         int i;
1398         unsigned short esdmode;         /* Extended SDRAM mode */
1399         unsigned short sdmode;          /* SDRAM mode */
1400
1401         /* Mode Register - MR1 */
1402         unsigned int qoff = 0;          /* Output buffer enable 0=yes, 1=no */
1403         unsigned int tdqs_en = 0;       /* TDQS Enable: 0=no, 1=yes */
1404         unsigned int rtt;
1405         unsigned int wrlvl_en = 0;      /* Write level enable: 0=no, 1=yes */
1406         unsigned int al = 0;            /* Posted CAS# additive latency (AL) */
1407         unsigned int dic = 0;           /* Output driver impedance, 40ohm */
1408         unsigned int dll_en = 0;        /* DLL Enable  0=Enable (Normal),
1409                                                        1=Disable (Test/Debug) */
1410
1411         /* Mode Register - MR0 */
1412         unsigned int dll_on;    /* DLL control for precharge PD, 0=off, 1=on */
1413         unsigned int wr = 0;    /* Write Recovery */
1414         unsigned int dll_rst;   /* DLL Reset */
1415         unsigned int mode;      /* Normal=0 or Test=1 */
1416         unsigned int caslat = 4;/* CAS# latency, default set as 6 cycles */
1417         /* BT: Burst Type (0=Nibble Sequential, 1=Interleaved) */
1418         unsigned int bt;
1419         unsigned int bl;        /* BL: Burst Length */
1420
1421         unsigned int wr_mclk;
1422         /*
1423          * DDR_SDRAM_MODE doesn't support 9,11,13,15
1424          * Please refer JEDEC Standard No. 79-3E for Mode Register MR0
1425          * for this table
1426          */
1427         static const u8 wr_table[] = {1, 2, 3, 4, 5, 5, 6, 6, 7, 7, 0, 0};
1428
1429         if (popts->rtt_override)
1430                 rtt = popts->rtt_override_value;
1431         else
1432                 rtt = popts->cs_local_opts[0].odt_rtt_norm;
1433
1434         if (additive_latency == (cas_latency - 1))
1435                 al = 1;
1436         if (additive_latency == (cas_latency - 2))
1437                 al = 2;
1438
1439         if (popts->quad_rank_present)
1440                 dic = 1;        /* output driver impedance 240/7 ohm */
1441
1442         /*
1443          * The esdmode value will also be used for writing
1444          * MR1 during write leveling for DDR3, although the
1445          * bits specifically related to the write leveling
1446          * scheme will be handled automatically by the DDR
1447          * controller. so we set the wrlvl_en = 0 here.
1448          */
1449         esdmode = (0
1450                 | ((qoff & 0x1) << 12)
1451                 | ((tdqs_en & 0x1) << 11)
1452                 | ((rtt & 0x4) << 7)   /* rtt field is split */
1453                 | ((wrlvl_en & 0x1) << 7)
1454                 | ((rtt & 0x2) << 5)   /* rtt field is split */
1455                 | ((dic & 0x2) << 4)   /* DIC field is split */
1456                 | ((al & 0x3) << 3)
1457                 | ((rtt & 0x1) << 2)  /* rtt field is split */
1458                 | ((dic & 0x1) << 1)   /* DIC field is split */
1459                 | ((dll_en & 0x1) << 0)
1460                 );
1461
1462         /*
1463          * DLL control for precharge PD
1464          * 0=slow exit DLL off (tXPDLL)
1465          * 1=fast exit DLL on (tXP)
1466          */
1467         dll_on = 1;
1468
1469         wr_mclk = picos_to_mclk(common_dimm->twr_ps);
1470         if (wr_mclk <= 16) {
1471                 wr = wr_table[wr_mclk - 5];
1472         } else {
1473                 printf("Error: unsupported write recovery for mode register "
1474                        "wr_mclk = %d\n", wr_mclk);
1475         }
1476
1477         dll_rst = 0;    /* dll no reset */
1478         mode = 0;       /* normal mode */
1479
1480         /* look up table to get the cas latency bits */
1481         if (cas_latency >= 5 && cas_latency <= 16) {
1482                 unsigned char cas_latency_table[] = {
1483                         0x2,    /* 5 clocks */
1484                         0x4,    /* 6 clocks */
1485                         0x6,    /* 7 clocks */
1486                         0x8,    /* 8 clocks */
1487                         0xa,    /* 9 clocks */
1488                         0xc,    /* 10 clocks */
1489                         0xe,    /* 11 clocks */
1490                         0x1,    /* 12 clocks */
1491                         0x3,    /* 13 clocks */
1492                         0x5,    /* 14 clocks */
1493                         0x7,    /* 15 clocks */
1494                         0x9,    /* 16 clocks */
1495                 };
1496                 caslat = cas_latency_table[cas_latency - 5];
1497         } else {
1498                 printf("Error: unsupported cas latency for mode register\n");
1499         }
1500
1501         bt = 0; /* Nibble sequential */
1502
1503         switch (popts->burst_length) {
1504         case DDR_BL8:
1505                 bl = 0;
1506                 break;
1507         case DDR_OTF:
1508                 bl = 1;
1509                 break;
1510         case DDR_BC4:
1511                 bl = 2;
1512                 break;
1513         default:
1514                 printf("Error: invalid burst length of %u specified. "
1515                         " Defaulting to on-the-fly BC4 or BL8 beats.\n",
1516                         popts->burst_length);
1517                 bl = 1;
1518                 break;
1519         }
1520
1521         sdmode = (0
1522                   | ((dll_on & 0x1) << 12)
1523                   | ((wr & 0x7) << 9)
1524                   | ((dll_rst & 0x1) << 8)
1525                   | ((mode & 0x1) << 7)
1526                   | (((caslat >> 1) & 0x7) << 4)
1527                   | ((bt & 0x1) << 3)
1528                   | ((caslat & 1) << 2)
1529                   | ((bl & 0x3) << 0)
1530                   );
1531
1532         ddr->ddr_sdram_mode = (0
1533                                | ((esdmode & 0xFFFF) << 16)
1534                                | ((sdmode & 0xFFFF) << 0)
1535                                );
1536
1537         debug("FSLDDR: ddr_sdram_mode = 0x%08x\n", ddr->ddr_sdram_mode);
1538
1539         if (unq_mrs_en) {       /* unique mode registers are supported */
1540                 for (i = 1; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
1541                         if (popts->rtt_override)
1542                                 rtt = popts->rtt_override_value;
1543                         else
1544                                 rtt = popts->cs_local_opts[i].odt_rtt_norm;
1545
1546                         esdmode &= 0xFDBB;      /* clear bit 9,6,2 */
1547                         esdmode |= (0
1548                                 | ((rtt & 0x4) << 7)   /* rtt field is split */
1549                                 | ((rtt & 0x2) << 5)   /* rtt field is split */
1550                                 | ((rtt & 0x1) << 2)  /* rtt field is split */
1551                                 );
1552                         switch (i) {
1553                         case 1:
1554                                 ddr->ddr_sdram_mode_3 = (0
1555                                        | ((esdmode & 0xFFFF) << 16)
1556                                        | ((sdmode & 0xFFFF) << 0)
1557                                        );
1558                                 break;
1559                         case 2:
1560                                 ddr->ddr_sdram_mode_5 = (0
1561                                        | ((esdmode & 0xFFFF) << 16)
1562                                        | ((sdmode & 0xFFFF) << 0)
1563                                        );
1564                                 break;
1565                         case 3:
1566                                 ddr->ddr_sdram_mode_7 = (0
1567                                        | ((esdmode & 0xFFFF) << 16)
1568                                        | ((sdmode & 0xFFFF) << 0)
1569                                        );
1570                                 break;
1571                         }
1572                 }
1573                 debug("FSLDDR: ddr_sdram_mode_3 = 0x%08x\n",
1574                         ddr->ddr_sdram_mode_3);
1575                 debug("FSLDDR: ddr_sdram_mode_5 = 0x%08x\n",
1576                         ddr->ddr_sdram_mode_5);
1577                 debug("FSLDDR: ddr_sdram_mode_5 = 0x%08x\n",
1578                         ddr->ddr_sdram_mode_5);
1579         }
1580 }
1581
1582 #else /* !CONFIG_SYS_FSL_DDR3 */
1583
1584 /* DDR SDRAM Mode configuration set (DDR_SDRAM_MODE) */
1585 static void set_ddr_sdram_mode(fsl_ddr_cfg_regs_t *ddr,
1586                                const memctl_options_t *popts,
1587                                const common_timing_params_t *common_dimm,
1588                                unsigned int cas_latency,
1589                                unsigned int additive_latency,
1590                                const unsigned int unq_mrs_en)
1591 {
1592         unsigned short esdmode;         /* Extended SDRAM mode */
1593         unsigned short sdmode;          /* SDRAM mode */
1594
1595         /*
1596          * FIXME: This ought to be pre-calculated in a
1597          * technology-specific routine,
1598          * e.g. compute_DDR2_mode_register(), and then the
1599          * sdmode and esdmode passed in as part of common_dimm.
1600          */
1601
1602         /* Extended Mode Register */
1603         unsigned int mrs = 0;           /* Mode Register Set */
1604         unsigned int outputs = 0;       /* 0=Enabled, 1=Disabled */
1605         unsigned int rdqs_en = 0;       /* RDQS Enable: 0=no, 1=yes */
1606         unsigned int dqs_en = 0;        /* DQS# Enable: 0=enable, 1=disable */
1607         unsigned int ocd = 0;           /* 0x0=OCD not supported,
1608                                            0x7=OCD default state */
1609         unsigned int rtt;
1610         unsigned int al;                /* Posted CAS# additive latency (AL) */
1611         unsigned int ods = 0;           /* Output Drive Strength:
1612                                                 0 = Full strength (18ohm)
1613                                                 1 = Reduced strength (4ohm) */
1614         unsigned int dll_en = 0;        /* DLL Enable  0=Enable (Normal),
1615                                                        1=Disable (Test/Debug) */
1616
1617         /* Mode Register (MR) */
1618         unsigned int mr;        /* Mode Register Definition */
1619         unsigned int pd;        /* Power-Down Mode */
1620         unsigned int wr;        /* Write Recovery */
1621         unsigned int dll_res;   /* DLL Reset */
1622         unsigned int mode;      /* Normal=0 or Test=1 */
1623         unsigned int caslat = 0;/* CAS# latency */
1624         /* BT: Burst Type (0=Sequential, 1=Interleaved) */
1625         unsigned int bt;
1626         unsigned int bl;        /* BL: Burst Length */
1627
1628         dqs_en = !popts->dqs_config;
1629         rtt = fsl_ddr_get_rtt();
1630
1631         al = additive_latency;
1632
1633         esdmode = (0
1634                 | ((mrs & 0x3) << 14)
1635                 | ((outputs & 0x1) << 12)
1636                 | ((rdqs_en & 0x1) << 11)
1637                 | ((dqs_en & 0x1) << 10)
1638                 | ((ocd & 0x7) << 7)
1639                 | ((rtt & 0x2) << 5)   /* rtt field is split */
1640                 | ((al & 0x7) << 3)
1641                 | ((rtt & 0x1) << 2)   /* rtt field is split */
1642                 | ((ods & 0x1) << 1)
1643                 | ((dll_en & 0x1) << 0)
1644                 );
1645
1646         mr = 0;          /* FIXME: CHECKME */
1647
1648         /*
1649          * 0 = Fast Exit (Normal)
1650          * 1 = Slow Exit (Low Power)
1651          */
1652         pd = 0;
1653
1654 #if defined(CONFIG_SYS_FSL_DDR1)
1655         wr = 0;       /* Historical */
1656 #elif defined(CONFIG_SYS_FSL_DDR2)
1657         wr = picos_to_mclk(common_dimm->twr_ps);
1658 #endif
1659         dll_res = 0;
1660         mode = 0;
1661
1662 #if defined(CONFIG_SYS_FSL_DDR1)
1663         if (1 <= cas_latency && cas_latency <= 4) {
1664                 unsigned char mode_caslat_table[4] = {
1665                         0x5,    /* 1.5 clocks */
1666                         0x2,    /* 2.0 clocks */
1667                         0x6,    /* 2.5 clocks */
1668                         0x3     /* 3.0 clocks */
1669                 };
1670                 caslat = mode_caslat_table[cas_latency - 1];
1671         } else {
1672                 printf("Warning: unknown cas_latency %d\n", cas_latency);
1673         }
1674 #elif defined(CONFIG_SYS_FSL_DDR2)
1675         caslat = cas_latency;
1676 #endif
1677         bt = 0;
1678
1679         switch (popts->burst_length) {
1680         case DDR_BL4:
1681                 bl = 2;
1682                 break;
1683         case DDR_BL8:
1684                 bl = 3;
1685                 break;
1686         default:
1687                 printf("Error: invalid burst length of %u specified. "
1688                         " Defaulting to 4 beats.\n",
1689                         popts->burst_length);
1690                 bl = 2;
1691                 break;
1692         }
1693
1694         sdmode = (0
1695                   | ((mr & 0x3) << 14)
1696                   | ((pd & 0x1) << 12)
1697                   | ((wr & 0x7) << 9)
1698                   | ((dll_res & 0x1) << 8)
1699                   | ((mode & 0x1) << 7)
1700                   | ((caslat & 0x7) << 4)
1701                   | ((bt & 0x1) << 3)
1702                   | ((bl & 0x7) << 0)
1703                   );
1704
1705         ddr->ddr_sdram_mode = (0
1706                                | ((esdmode & 0xFFFF) << 16)
1707                                | ((sdmode & 0xFFFF) << 0)
1708                                );
1709         debug("FSLDDR: ddr_sdram_mode = 0x%08x\n", ddr->ddr_sdram_mode);
1710 }
1711 #endif
1712
1713 /* DDR SDRAM Data Initialization (DDR_DATA_INIT) */
1714 static void set_ddr_data_init(fsl_ddr_cfg_regs_t *ddr)
1715 {
1716         unsigned int init_value;        /* Initialization value */
1717
1718 #ifdef CONFIG_MEM_INIT_VALUE
1719         init_value = CONFIG_MEM_INIT_VALUE;
1720 #else
1721         init_value = 0xDEADBEEF;
1722 #endif
1723         ddr->ddr_data_init = init_value;
1724 }
1725
1726 /*
1727  * DDR SDRAM Clock Control (DDR_SDRAM_CLK_CNTL)
1728  * The old controller on the 8540/60 doesn't have this register.
1729  * Hope it's OK to set it (to 0) anyway.
1730  */
1731 static void set_ddr_sdram_clk_cntl(fsl_ddr_cfg_regs_t *ddr,
1732                                          const memctl_options_t *popts)
1733 {
1734         unsigned int clk_adjust;        /* Clock adjust */
1735
1736         clk_adjust = popts->clk_adjust;
1737         ddr->ddr_sdram_clk_cntl = (clk_adjust & 0xF) << 23;
1738         debug("FSLDDR: clk_cntl = 0x%08x\n", ddr->ddr_sdram_clk_cntl);
1739 }
1740
1741 /* DDR Initialization Address (DDR_INIT_ADDR) */
1742 static void set_ddr_init_addr(fsl_ddr_cfg_regs_t *ddr)
1743 {
1744         unsigned int init_addr = 0;     /* Initialization address */
1745
1746         ddr->ddr_init_addr = init_addr;
1747 }
1748
1749 /* DDR Initialization Address (DDR_INIT_EXT_ADDR) */
1750 static void set_ddr_init_ext_addr(fsl_ddr_cfg_regs_t *ddr)
1751 {
1752         unsigned int uia = 0;   /* Use initialization address */
1753         unsigned int init_ext_addr = 0; /* Initialization address */
1754
1755         ddr->ddr_init_ext_addr = (0
1756                                   | ((uia & 0x1) << 31)
1757                                   | (init_ext_addr & 0xF)
1758                                   );
1759 }
1760
1761 /* DDR SDRAM Timing Configuration 4 (TIMING_CFG_4) */
1762 static void set_timing_cfg_4(fsl_ddr_cfg_regs_t *ddr,
1763                                 const memctl_options_t *popts)
1764 {
1765         unsigned int rwt = 0; /* Read-to-write turnaround for same CS */
1766         unsigned int wrt = 0; /* Write-to-read turnaround for same CS */
1767         unsigned int rrt = 0; /* Read-to-read turnaround for same CS */
1768         unsigned int wwt = 0; /* Write-to-write turnaround for same CS */
1769         unsigned int dll_lock = 0; /* DDR SDRAM DLL Lock Time */
1770
1771 #if defined(CONFIG_SYS_FSL_DDR3) || defined(CONFIG_SYS_FSL_DDR4)
1772         if (popts->burst_length == DDR_BL8) {
1773                 /* We set BL/2 for fixed BL8 */
1774                 rrt = 0;        /* BL/2 clocks */
1775                 wwt = 0;        /* BL/2 clocks */
1776         } else {
1777                 /* We need to set BL/2 + 2 to BC4 and OTF */
1778                 rrt = 2;        /* BL/2 + 2 clocks */
1779                 wwt = 2;        /* BL/2 + 2 clocks */
1780         }
1781 #endif
1782
1783 #ifdef CONFIG_SYS_FSL_DDR4
1784         dll_lock = 2;   /* tDLLK = 1024 clocks */
1785 #elif defined(CONFIG_SYS_FSL_DDR3)
1786         dll_lock = 1;   /* tDLLK = 512 clocks from spec */
1787 #endif
1788         ddr->timing_cfg_4 = (0
1789                              | ((rwt & 0xf) << 28)
1790                              | ((wrt & 0xf) << 24)
1791                              | ((rrt & 0xf) << 20)
1792                              | ((wwt & 0xf) << 16)
1793                              | (dll_lock & 0x3)
1794                              );
1795         debug("FSLDDR: timing_cfg_4 = 0x%08x\n", ddr->timing_cfg_4);
1796 }
1797
1798 /* DDR SDRAM Timing Configuration 5 (TIMING_CFG_5) */
1799 static void set_timing_cfg_5(fsl_ddr_cfg_regs_t *ddr, unsigned int cas_latency)
1800 {
1801         unsigned int rodt_on = 0;       /* Read to ODT on */
1802         unsigned int rodt_off = 0;      /* Read to ODT off */
1803         unsigned int wodt_on = 0;       /* Write to ODT on */
1804         unsigned int wodt_off = 0;      /* Write to ODT off */
1805
1806 #if defined(CONFIG_SYS_FSL_DDR3) || defined(CONFIG_SYS_FSL_DDR4)
1807         unsigned int wr_lat = ((ddr->timing_cfg_2 & 0x00780000) >> 19) +
1808                               ((ddr->timing_cfg_2 & 0x00040000) >> 14);
1809         /* rodt_on = timing_cfg_1[caslat] - timing_cfg_2[wrlat] + 1 */
1810         if (cas_latency >= wr_lat)
1811                 rodt_on = cas_latency - wr_lat + 1;
1812         rodt_off = 4;   /*  4 clocks */
1813         wodt_on = 1;    /*  1 clocks */
1814         wodt_off = 4;   /*  4 clocks */
1815 #endif
1816
1817         ddr->timing_cfg_5 = (0
1818                              | ((rodt_on & 0x1f) << 24)
1819                              | ((rodt_off & 0x7) << 20)
1820                              | ((wodt_on & 0x1f) << 12)
1821                              | ((wodt_off & 0x7) << 8)
1822                              );
1823         debug("FSLDDR: timing_cfg_5 = 0x%08x\n", ddr->timing_cfg_5);
1824 }
1825
1826 #ifdef CONFIG_SYS_FSL_DDR4
1827 static void set_timing_cfg_6(fsl_ddr_cfg_regs_t *ddr)
1828 {
1829         unsigned int hs_caslat = 0;
1830         unsigned int hs_wrlat = 0;
1831         unsigned int hs_wrrec = 0;
1832         unsigned int hs_clkadj = 0;
1833         unsigned int hs_wrlvl_start = 0;
1834
1835         ddr->timing_cfg_6 = (0
1836                              | ((hs_caslat & 0x1f) << 24)
1837                              | ((hs_wrlat & 0x1f) << 19)
1838                              | ((hs_wrrec & 0x1f) << 12)
1839                              | ((hs_clkadj & 0x1f) << 6)
1840                              | ((hs_wrlvl_start & 0x1f) << 0)
1841                             );
1842         debug("FSLDDR: timing_cfg_6 = 0x%08x\n", ddr->timing_cfg_6);
1843 }
1844
1845 static void set_timing_cfg_7(fsl_ddr_cfg_regs_t *ddr,
1846                         const common_timing_params_t *common_dimm)
1847 {
1848         unsigned int txpr, tcksre, tcksrx;
1849         unsigned int cke_rst, cksre, cksrx, par_lat, cs_to_cmd;
1850
1851         txpr = max(5U, picos_to_mclk(common_dimm->trfc1_ps + 10000));
1852         tcksre = max(5U, picos_to_mclk(10000));
1853         tcksrx = max(5U, picos_to_mclk(10000));
1854         par_lat = 0;
1855         cs_to_cmd = 0;
1856
1857         if (txpr <= 200)
1858                 cke_rst = 0;
1859         else if (txpr <= 256)
1860                 cke_rst = 1;
1861         else if (txpr <= 512)
1862                 cke_rst = 2;
1863         else
1864                 cke_rst = 3;
1865
1866         if (tcksre <= 19)
1867                 cksre = tcksre - 5;
1868         else
1869                 cksre = 15;
1870
1871         if (tcksrx <= 19)
1872                 cksrx = tcksrx - 5;
1873         else
1874                 cksrx = 15;
1875
1876         ddr->timing_cfg_7 = (0
1877                              | ((cke_rst & 0x3) << 28)
1878                              | ((cksre & 0xf) << 24)
1879                              | ((cksrx & 0xf) << 20)
1880                              | ((par_lat & 0xf) << 16)
1881                              | ((cs_to_cmd & 0xf) << 4)
1882                             );
1883         debug("FSLDDR: timing_cfg_7 = 0x%08x\n", ddr->timing_cfg_7);
1884 }
1885
1886 static void set_timing_cfg_8(fsl_ddr_cfg_regs_t *ddr,
1887                              const memctl_options_t *popts,
1888                              const common_timing_params_t *common_dimm,
1889                              unsigned int cas_latency)
1890 {
1891         unsigned int rwt_bg, wrt_bg, rrt_bg, wwt_bg;
1892         unsigned int acttoact_bg, wrtord_bg, pre_all_rec;
1893         unsigned int tccdl = picos_to_mclk(common_dimm->tccdl_ps);
1894         unsigned int wr_lat = ((ddr->timing_cfg_2 & 0x00780000) >> 19) +
1895                               ((ddr->timing_cfg_2 & 0x00040000) >> 14);
1896
1897         rwt_bg = cas_latency + 2 + 4 - wr_lat;
1898         if (rwt_bg < tccdl)
1899                 rwt_bg = tccdl - rwt_bg;
1900         else
1901                 rwt_bg = 0;
1902
1903         wrt_bg = wr_lat + 4 + 1 - cas_latency;
1904         if (wrt_bg < tccdl)
1905                 wrt_bg = tccdl - wrt_bg;
1906         else
1907                 wrt_bg = 0;
1908
1909         if (popts->burst_length == DDR_BL8) {
1910                 rrt_bg = tccdl - 4;
1911                 wwt_bg = tccdl - 4;
1912         } else {
1913                 rrt_bg = tccdl - 2;
1914                 wwt_bg = tccdl - 4;
1915         }
1916
1917         acttoact_bg = picos_to_mclk(common_dimm->trrdl_ps);
1918         wrtord_bg = max(4U, picos_to_mclk(7500));
1919         if (popts->otf_burst_chop_en)
1920                 wrtord_bg += 2;
1921
1922         pre_all_rec = 0;
1923
1924         ddr->timing_cfg_8 = (0
1925                              | ((rwt_bg & 0xf) << 28)
1926                              | ((wrt_bg & 0xf) << 24)
1927                              | ((rrt_bg & 0xf) << 20)
1928                              | ((wwt_bg & 0xf) << 16)
1929                              | ((acttoact_bg & 0xf) << 12)
1930                              | ((wrtord_bg & 0xf) << 8)
1931                              | ((pre_all_rec & 0x1f) << 0)
1932                             );
1933
1934         debug("FSLDDR: timing_cfg_8 = 0x%08x\n", ddr->timing_cfg_8);
1935 }
1936
1937 static void set_timing_cfg_9(fsl_ddr_cfg_regs_t *ddr)
1938 {
1939         ddr->timing_cfg_9 = 0;
1940         debug("FSLDDR: timing_cfg_9 = 0x%08x\n", ddr->timing_cfg_9);
1941 }
1942
1943 /* This function needs to be called after set_ddr_sdram_cfg() is called */
1944 static void set_ddr_dq_mapping(fsl_ddr_cfg_regs_t *ddr,
1945                                const dimm_params_t *dimm_params)
1946 {
1947         unsigned int acc_ecc_en = (ddr->ddr_sdram_cfg >> 2) & 0x1;
1948
1949         ddr->dq_map_0 = ((dimm_params->dq_mapping[0] & 0x3F) << 26) |
1950                         ((dimm_params->dq_mapping[1] & 0x3F) << 20) |
1951                         ((dimm_params->dq_mapping[2] & 0x3F) << 14) |
1952                         ((dimm_params->dq_mapping[3] & 0x3F) << 8) |
1953                         ((dimm_params->dq_mapping[4] & 0x3F) << 2);
1954
1955         ddr->dq_map_1 = ((dimm_params->dq_mapping[5] & 0x3F) << 26) |
1956                         ((dimm_params->dq_mapping[6] & 0x3F) << 20) |
1957                         ((dimm_params->dq_mapping[7] & 0x3F) << 14) |
1958                         ((dimm_params->dq_mapping[10] & 0x3F) << 8) |
1959                         ((dimm_params->dq_mapping[11] & 0x3F) << 2);
1960
1961         ddr->dq_map_2 = ((dimm_params->dq_mapping[12] & 0x3F) << 26) |
1962                         ((dimm_params->dq_mapping[13] & 0x3F) << 20) |
1963                         ((dimm_params->dq_mapping[14] & 0x3F) << 14) |
1964                         ((dimm_params->dq_mapping[15] & 0x3F) << 8) |
1965                         ((dimm_params->dq_mapping[16] & 0x3F) << 2);
1966
1967         /* dq_map for ECC[4:7] is set to 0 if accumulated ECC is enabled */
1968         ddr->dq_map_3 = ((dimm_params->dq_mapping[17] & 0x3F) << 26) |
1969                         ((dimm_params->dq_mapping[8] & 0x3F) << 20) |
1970                         (acc_ecc_en ? 0 :
1971                          (dimm_params->dq_mapping[9] & 0x3F) << 14) |
1972                         dimm_params->dq_mapping_ors;
1973
1974         debug("FSLDDR: dq_map_0 = 0x%08x\n", ddr->dq_map_0);
1975         debug("FSLDDR: dq_map_1 = 0x%08x\n", ddr->dq_map_1);
1976         debug("FSLDDR: dq_map_2 = 0x%08x\n", ddr->dq_map_2);
1977         debug("FSLDDR: dq_map_3 = 0x%08x\n", ddr->dq_map_3);
1978 }
1979 static void set_ddr_sdram_cfg_3(fsl_ddr_cfg_regs_t *ddr,
1980                                const memctl_options_t *popts)
1981 {
1982         int rd_pre;
1983
1984         rd_pre = popts->quad_rank_present ? 1 : 0;
1985
1986         ddr->ddr_sdram_cfg_3 = (rd_pre & 0x1) << 16;
1987
1988         debug("FSLDDR: ddr_sdram_cfg_3 = 0x%08x\n", ddr->ddr_sdram_cfg_3);
1989 }
1990 #endif  /* CONFIG_SYS_FSL_DDR4 */
1991
1992 /* DDR ZQ Calibration Control (DDR_ZQ_CNTL) */
1993 static void set_ddr_zq_cntl(fsl_ddr_cfg_regs_t *ddr, unsigned int zq_en)
1994 {
1995         unsigned int zqinit = 0;/* POR ZQ Calibration Time (tZQinit) */
1996         /* Normal Operation Full Calibration Time (tZQoper) */
1997         unsigned int zqoper = 0;
1998         /* Normal Operation Short Calibration Time (tZQCS) */
1999         unsigned int zqcs = 0;
2000 #ifdef CONFIG_SYS_FSL_DDR4
2001         unsigned int zqcs_init;
2002 #endif
2003
2004         if (zq_en) {
2005 #ifdef CONFIG_SYS_FSL_DDR4
2006                 zqinit = 10;    /* 1024 clocks */
2007                 zqoper = 9;     /* 512 clocks */
2008                 zqcs = 7;       /* 128 clocks */
2009                 zqcs_init = 5;  /* 1024 refresh sequences */
2010 #else
2011                 zqinit = 9;     /* 512 clocks */
2012                 zqoper = 8;     /* 256 clocks */
2013                 zqcs = 6;       /* 64 clocks */
2014 #endif
2015         }
2016
2017         ddr->ddr_zq_cntl = (0
2018                             | ((zq_en & 0x1) << 31)
2019                             | ((zqinit & 0xF) << 24)
2020                             | ((zqoper & 0xF) << 16)
2021                             | ((zqcs & 0xF) << 8)
2022 #ifdef CONFIG_SYS_FSL_DDR4
2023                             | ((zqcs_init & 0xF) << 0)
2024 #endif
2025                             );
2026         debug("FSLDDR: zq_cntl = 0x%08x\n", ddr->ddr_zq_cntl);
2027 }
2028
2029 /* DDR Write Leveling Control (DDR_WRLVL_CNTL) */
2030 static void set_ddr_wrlvl_cntl(fsl_ddr_cfg_regs_t *ddr, unsigned int wrlvl_en,
2031                                 const memctl_options_t *popts)
2032 {
2033         /*
2034          * First DQS pulse rising edge after margining mode
2035          * is programmed (tWL_MRD)
2036          */
2037         unsigned int wrlvl_mrd = 0;
2038         /* ODT delay after margining mode is programmed (tWL_ODTEN) */
2039         unsigned int wrlvl_odten = 0;
2040         /* DQS/DQS_ delay after margining mode is programmed (tWL_DQSEN) */
2041         unsigned int wrlvl_dqsen = 0;
2042         /* WRLVL_SMPL: Write leveling sample time */
2043         unsigned int wrlvl_smpl = 0;
2044         /* WRLVL_WLR: Write leveling repeition time */
2045         unsigned int wrlvl_wlr = 0;
2046         /* WRLVL_START: Write leveling start time */
2047         unsigned int wrlvl_start = 0;
2048
2049         /* suggest enable write leveling for DDR3 due to fly-by topology */
2050         if (wrlvl_en) {
2051                 /* tWL_MRD min = 40 nCK, we set it 64 */
2052                 wrlvl_mrd = 0x6;
2053                 /* tWL_ODTEN 128 */
2054                 wrlvl_odten = 0x7;
2055                 /* tWL_DQSEN min = 25 nCK, we set it 32 */
2056                 wrlvl_dqsen = 0x5;
2057                 /*
2058                  * Write leveling sample time at least need 6 clocks
2059                  * higher than tWLO to allow enough time for progagation
2060                  * delay and sampling the prime data bits.
2061                  */
2062                 wrlvl_smpl = 0xf;
2063                 /*
2064                  * Write leveling repetition time
2065                  * at least tWLO + 6 clocks clocks
2066                  * we set it 64
2067                  */
2068                 wrlvl_wlr = 0x6;
2069                 /*
2070                  * Write leveling start time
2071                  * The value use for the DQS_ADJUST for the first sample
2072                  * when write leveling is enabled. It probably needs to be
2073                  * overriden per platform.
2074                  */
2075                 wrlvl_start = 0x8;
2076                 /*
2077                  * Override the write leveling sample and start time
2078                  * according to specific board
2079                  */
2080                 if (popts->wrlvl_override) {
2081                         wrlvl_smpl = popts->wrlvl_sample;
2082                         wrlvl_start = popts->wrlvl_start;
2083                 }
2084         }
2085
2086         ddr->ddr_wrlvl_cntl = (0
2087                                | ((wrlvl_en & 0x1) << 31)
2088                                | ((wrlvl_mrd & 0x7) << 24)
2089                                | ((wrlvl_odten & 0x7) << 20)
2090                                | ((wrlvl_dqsen & 0x7) << 16)
2091                                | ((wrlvl_smpl & 0xf) << 12)
2092                                | ((wrlvl_wlr & 0x7) << 8)
2093                                | ((wrlvl_start & 0x1F) << 0)
2094                                );
2095         debug("FSLDDR: wrlvl_cntl = 0x%08x\n", ddr->ddr_wrlvl_cntl);
2096         ddr->ddr_wrlvl_cntl_2 = popts->wrlvl_ctl_2;
2097         debug("FSLDDR: wrlvl_cntl_2 = 0x%08x\n", ddr->ddr_wrlvl_cntl_2);
2098         ddr->ddr_wrlvl_cntl_3 = popts->wrlvl_ctl_3;
2099         debug("FSLDDR: wrlvl_cntl_3 = 0x%08x\n", ddr->ddr_wrlvl_cntl_3);
2100
2101 }
2102
2103 /* DDR Self Refresh Counter (DDR_SR_CNTR) */
2104 static void set_ddr_sr_cntr(fsl_ddr_cfg_regs_t *ddr, unsigned int sr_it)
2105 {
2106         /* Self Refresh Idle Threshold */
2107         ddr->ddr_sr_cntr = (sr_it & 0xF) << 16;
2108 }
2109
2110 static void set_ddr_eor(fsl_ddr_cfg_regs_t *ddr, const memctl_options_t *popts)
2111 {
2112         if (popts->addr_hash) {
2113                 ddr->ddr_eor = 0x40000000;      /* address hash enable */
2114                 puts("Address hashing enabled.\n");
2115         }
2116 }
2117
2118 static void set_ddr_cdr1(fsl_ddr_cfg_regs_t *ddr, const memctl_options_t *popts)
2119 {
2120         ddr->ddr_cdr1 = popts->ddr_cdr1;
2121         debug("FSLDDR: ddr_cdr1 = 0x%08x\n", ddr->ddr_cdr1);
2122 }
2123
2124 static void set_ddr_cdr2(fsl_ddr_cfg_regs_t *ddr, const memctl_options_t *popts)
2125 {
2126         ddr->ddr_cdr2 = popts->ddr_cdr2;
2127         debug("FSLDDR: ddr_cdr2 = 0x%08x\n", ddr->ddr_cdr2);
2128 }
2129
2130 unsigned int
2131 check_fsl_memctl_config_regs(const fsl_ddr_cfg_regs_t *ddr)
2132 {
2133         unsigned int res = 0;
2134
2135         /*
2136          * Check that DDR_SDRAM_CFG[RD_EN] and DDR_SDRAM_CFG[2T_EN] are
2137          * not set at the same time.
2138          */
2139         if (ddr->ddr_sdram_cfg & 0x10000000
2140             && ddr->ddr_sdram_cfg & 0x00008000) {
2141                 printf("Error: DDR_SDRAM_CFG[RD_EN] and DDR_SDRAM_CFG[2T_EN] "
2142                                 " should not be set at the same time.\n");
2143                 res++;
2144         }
2145
2146         return res;
2147 }
2148
2149 unsigned int
2150 compute_fsl_memctl_config_regs(const memctl_options_t *popts,
2151                                fsl_ddr_cfg_regs_t *ddr,
2152                                const common_timing_params_t *common_dimm,
2153                                const dimm_params_t *dimm_params,
2154                                unsigned int dbw_cap_adj,
2155                                unsigned int size_only)
2156 {
2157         unsigned int i;
2158         unsigned int cas_latency;
2159         unsigned int additive_latency;
2160         unsigned int sr_it;
2161         unsigned int zq_en;
2162         unsigned int wrlvl_en;
2163         unsigned int ip_rev = 0;
2164         unsigned int unq_mrs_en = 0;
2165         int cs_en = 1;
2166
2167         memset(ddr, 0, sizeof(fsl_ddr_cfg_regs_t));
2168
2169         if (common_dimm == NULL) {
2170                 printf("Error: subset DIMM params struct null pointer\n");
2171                 return 1;
2172         }
2173
2174         /*
2175          * Process overrides first.
2176          *
2177          * FIXME: somehow add dereated caslat to this
2178          */
2179         cas_latency = (popts->cas_latency_override)
2180                 ? popts->cas_latency_override_value
2181                 : common_dimm->lowest_common_spd_caslat;
2182
2183         additive_latency = (popts->additive_latency_override)
2184                 ? popts->additive_latency_override_value
2185                 : common_dimm->additive_latency;
2186
2187         sr_it = (popts->auto_self_refresh_en)
2188                 ? popts->sr_it
2189                 : 0;
2190         /* ZQ calibration */
2191         zq_en = (popts->zq_en) ? 1 : 0;
2192         /* write leveling */
2193         wrlvl_en = (popts->wrlvl_en) ? 1 : 0;
2194
2195         /* Chip Select Memory Bounds (CSn_BNDS) */
2196         for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
2197                 unsigned long long ea, sa;
2198                 unsigned int cs_per_dimm
2199                         = CONFIG_CHIP_SELECTS_PER_CTRL / CONFIG_DIMM_SLOTS_PER_CTLR;
2200                 unsigned int dimm_number
2201                         = i / cs_per_dimm;
2202                 unsigned long long rank_density
2203                         = dimm_params[dimm_number].rank_density >> dbw_cap_adj;
2204
2205                 if (dimm_params[dimm_number].n_ranks == 0) {
2206                         debug("Skipping setup of CS%u "
2207                                 "because n_ranks on DIMM %u is 0\n", i, dimm_number);
2208                         continue;
2209                 }
2210                 if (popts->memctl_interleaving) {
2211                         switch (popts->ba_intlv_ctl & FSL_DDR_CS0_CS1_CS2_CS3) {
2212                         case FSL_DDR_CS0_CS1_CS2_CS3:
2213                                 break;
2214                         case FSL_DDR_CS0_CS1:
2215                         case FSL_DDR_CS0_CS1_AND_CS2_CS3:
2216                                 if (i > 1)
2217                                         cs_en = 0;
2218                                 break;
2219                         case FSL_DDR_CS2_CS3:
2220                         default:
2221                                 if (i > 0)
2222                                         cs_en = 0;
2223                                 break;
2224                         }
2225                         sa = common_dimm->base_address;
2226                         ea = sa + common_dimm->total_mem - 1;
2227                 } else if (!popts->memctl_interleaving) {
2228                         /*
2229                          * If memory interleaving between controllers is NOT
2230                          * enabled, the starting address for each memory
2231                          * controller is distinct.  However, because rank
2232                          * interleaving is enabled, the starting and ending
2233                          * addresses of the total memory on that memory
2234                          * controller needs to be programmed into its
2235                          * respective CS0_BNDS.
2236                          */
2237                         switch (popts->ba_intlv_ctl & FSL_DDR_CS0_CS1_CS2_CS3) {
2238                         case FSL_DDR_CS0_CS1_CS2_CS3:
2239                                 sa = common_dimm->base_address;
2240                                 ea = sa + common_dimm->total_mem - 1;
2241                                 break;
2242                         case FSL_DDR_CS0_CS1_AND_CS2_CS3:
2243                                 if ((i >= 2) && (dimm_number == 0)) {
2244                                         sa = dimm_params[dimm_number].base_address +
2245                                               2 * rank_density;
2246                                         ea = sa + 2 * rank_density - 1;
2247                                 } else {
2248                                         sa = dimm_params[dimm_number].base_address;
2249                                         ea = sa + 2 * rank_density - 1;
2250                                 }
2251                                 break;
2252                         case FSL_DDR_CS0_CS1:
2253                                 if (dimm_params[dimm_number].n_ranks > (i % cs_per_dimm)) {
2254                                         sa = dimm_params[dimm_number].base_address;
2255                                         ea = sa + rank_density - 1;
2256                                         if (i != 1)
2257                                                 sa += (i % cs_per_dimm) * rank_density;
2258                                         ea += (i % cs_per_dimm) * rank_density;
2259                                 } else {
2260                                         sa = 0;
2261                                         ea = 0;
2262                                 }
2263                                 if (i == 0)
2264                                         ea += rank_density;
2265                                 break;
2266                         case FSL_DDR_CS2_CS3:
2267                                 if (dimm_params[dimm_number].n_ranks > (i % cs_per_dimm)) {
2268                                         sa = dimm_params[dimm_number].base_address;
2269                                         ea = sa + rank_density - 1;
2270                                         if (i != 3)
2271                                                 sa += (i % cs_per_dimm) * rank_density;
2272                                         ea += (i % cs_per_dimm) * rank_density;
2273                                 } else {
2274                                         sa = 0;
2275                                         ea = 0;
2276                                 }
2277                                 if (i == 2)
2278                                         ea += (rank_density >> dbw_cap_adj);
2279                                 break;
2280                         default:  /* No bank(chip-select) interleaving */
2281                                 sa = dimm_params[dimm_number].base_address;
2282                                 ea = sa + rank_density - 1;
2283                                 if (dimm_params[dimm_number].n_ranks > (i % cs_per_dimm)) {
2284                                         sa += (i % cs_per_dimm) * rank_density;
2285                                         ea += (i % cs_per_dimm) * rank_density;
2286                                 } else {
2287                                         sa = 0;
2288                                         ea = 0;
2289                                 }
2290                                 break;
2291                         }
2292                 }
2293
2294                 sa >>= 24;
2295                 ea >>= 24;
2296
2297                 if (cs_en) {
2298                         ddr->cs[i].bnds = (0
2299                                 | ((sa & 0xffff) << 16) /* starting address */
2300                                 | ((ea & 0xffff) << 0)  /* ending address */
2301                                 );
2302                 } else {
2303                         /* setting bnds to 0xffffffff for inactive CS */
2304                         ddr->cs[i].bnds = 0xffffffff;
2305                 }
2306
2307                 debug("FSLDDR: cs[%d]_bnds = 0x%08x\n", i, ddr->cs[i].bnds);
2308                 set_csn_config(dimm_number, i, ddr, popts, dimm_params);
2309                 set_csn_config_2(i, ddr);
2310         }
2311
2312         /*
2313          * In the case we only need to compute the ddr sdram size, we only need
2314          * to set csn registers, so return from here.
2315          */
2316         if (size_only)
2317                 return 0;
2318
2319         set_ddr_eor(ddr, popts);
2320
2321 #if !defined(CONFIG_SYS_FSL_DDR1)
2322         set_timing_cfg_0(ddr, popts, dimm_params);
2323 #endif
2324
2325         set_timing_cfg_3(ddr, popts, common_dimm, cas_latency,
2326                          additive_latency);
2327         set_timing_cfg_1(ddr, popts, common_dimm, cas_latency);
2328         set_timing_cfg_2(ddr, popts, common_dimm,
2329                                 cas_latency, additive_latency);
2330
2331         set_ddr_cdr1(ddr, popts);
2332         set_ddr_cdr2(ddr, popts);
2333         set_ddr_sdram_cfg(ddr, popts, common_dimm);
2334         ip_rev = fsl_ddr_get_version();
2335         if (ip_rev > 0x40400)
2336                 unq_mrs_en = 1;
2337
2338         if ((ip_rev > 0x40700) && (popts->cswl_override != 0))
2339                 ddr->debug[18] = popts->cswl_override;
2340
2341         set_ddr_sdram_cfg_2(ddr, popts, unq_mrs_en);
2342         set_ddr_sdram_mode(ddr, popts, common_dimm,
2343                                 cas_latency, additive_latency, unq_mrs_en);
2344         set_ddr_sdram_mode_2(ddr, popts, common_dimm, unq_mrs_en);
2345 #ifdef CONFIG_SYS_FSL_DDR4
2346         set_ddr_sdram_mode_9(ddr, popts, common_dimm, unq_mrs_en);
2347         set_ddr_sdram_mode_10(ddr, popts, common_dimm, unq_mrs_en);
2348 #endif
2349         set_ddr_sdram_interval(ddr, popts, common_dimm);
2350         set_ddr_data_init(ddr);
2351         set_ddr_sdram_clk_cntl(ddr, popts);
2352         set_ddr_init_addr(ddr);
2353         set_ddr_init_ext_addr(ddr);
2354         set_timing_cfg_4(ddr, popts);
2355         set_timing_cfg_5(ddr, cas_latency);
2356 #ifdef CONFIG_SYS_FSL_DDR4
2357         set_ddr_sdram_cfg_3(ddr, popts);
2358         set_timing_cfg_6(ddr);
2359         set_timing_cfg_7(ddr, common_dimm);
2360         set_timing_cfg_8(ddr, popts, common_dimm, cas_latency);
2361         set_timing_cfg_9(ddr);
2362         set_ddr_dq_mapping(ddr, dimm_params);
2363 #endif
2364
2365         set_ddr_zq_cntl(ddr, zq_en);
2366         set_ddr_wrlvl_cntl(ddr, wrlvl_en, popts);
2367
2368         set_ddr_sr_cntr(ddr, sr_it);
2369
2370         set_ddr_sdram_rcw(ddr, popts, common_dimm);
2371
2372 #ifdef CONFIG_SYS_FSL_DDR_EMU
2373         /* disble DDR training for emulator */
2374         ddr->debug[2] = 0x00000400;
2375         ddr->debug[4] = 0xff800800;
2376         ddr->debug[5] = 0x08000800;
2377         ddr->debug[6] = 0x08000800;
2378         ddr->debug[7] = 0x08000800;
2379         ddr->debug[8] = 0x08000800;
2380 #endif
2381 #ifdef CONFIG_SYS_FSL_ERRATUM_A004508
2382         if ((ip_rev >= 0x40000) && (ip_rev < 0x40400))
2383                 ddr->debug[2] |= 0x00000200;    /* set bit 22 */
2384 #endif
2385
2386         return check_fsl_memctl_config_regs(ddr);
2387 }