Fix SDRAM timing on Purple board

[karo-tx-uboot.git] / include / configs / hymod.h

/*
 * (C) Copyright 2000
 * Murray Jensen <Murray.Jensen@cmst.csiro.au>
 *
 * See file CREDITS for list of people who contributed to this
 * project.
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License as
 * published by the Free Software Foundation; either version 2 of
 * the License, or (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
 * MA 02111-1307 USA
 */

/*
 * Config header file for Hymod board
 */

#ifndef __CONFIG_H
#define __CONFIG_H

/*
 * High Level Configuration Options
 * (easy to change)
 */

#define CONFIG_MPC8260          1       /* This is an MPC8260 CPU       */
#define CONFIG_HYMOD            1       /* ...on a Hymod board          */

#define CONFIG_BOARD_POSTCLK_INIT       /* have board_postclk_init() function */

/*
 * select serial console configuration
 *
 * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
 * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
 * for SCC).
 *
 * if CONFIG_CONS_NONE is defined, then the serial console routines must
 * defined elsewhere (for example, on the cogent platform, there are serial
 * ports on the motherboard which are used for the serial console - see
 * cogent/cma101/serial.[ch]).
 */
#undef  CONFIG_CONS_ON_SMC              /* define if console on SMC */
#define CONFIG_CONS_ON_SCC              /* define if console on SCC */
#undef  CONFIG_CONS_NONE                /* define if console on something else*/
#define CONFIG_CONS_INDEX       1       /* which serial channel for console */
#define CONFIG_CONS_USE_EXTC            /* SMC/SCC use ext clock not brg_clk */
#define CONFIG_CONS_EXTC_RATE   3686400 /* SMC/SCC ext clk rate in Hz */
#define CONFIG_CONS_EXTC_PINSEL 0       /* pin select 0=CLK3/CLK9,1=CLK5/CLK15*/

/*
 * select ethernet configuration
 *
 * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then
 * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3
 * for FCC)
 *
 * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
 * defined elsewhere (as for the console), or CFG_CMD_NET must be removed
 * from CONFIG_COMMANDS to remove support for networking.
 */
#undef  CONFIG_ETHER_ON_SCC             /* define if ether on SCC       */
#define CONFIG_ETHER_ON_FCC             /* define if ether on FCC       */
#undef  CONFIG_ETHER_NONE               /* define if ether on something else */
#define CONFIG_ETHER_INDEX      1       /* which channel for ether      */

#if (CONFIG_ETHER_INDEX == 1)

/*
 * - Rx-CLK is CLK10
 * - Tx-CLK is CLK11
 * - RAM for BD/Buffers is on the 60x Bus (see 28-13)
 * - Enable Full Duplex in FSMR
 */
# define CFG_CMXFCR_MASK        (CMXFCR_FC1|CMXFCR_RF1CS_MSK|CMXFCR_TF1CS_MSK)
# define CFG_CMXFCR_VALUE       (CMXFCR_RF1CS_CLK10|CMXFCR_TF1CS_CLK11)
# define CFG_CPMFCR_RAMTYPE     0
# define CFG_FCC_PSMR           (FCC_PSMR_FDE|FCC_PSMR_LPB)

#elif (CONFIG_ETHER_INDEX == 2)

/*
 * - Rx-CLK is CLK13
 * - Tx-CLK is CLK14
 * - RAM for BD/Buffers is on the 60x Bus (see 28-13)
 * - Enable Full Duplex in FSMR
 */
# define CFG_CMXFCR_MASK        (CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK)
# define CFG_CMXFCR_VALUE       (CMXFCR_RF2CS_CLK13|CMXFCR_TF2CS_CLK14)
# define CFG_CPMFCR_RAMTYPE     0
# define CFG_FCC_PSMR           (FCC_PSMR_FDE|FCC_PSMR_LPB)

#elif (CONFIG_ETHER_INDEX == 3)

/*
 * - Rx-CLK is CLK15
 * - Tx-CLK is CLK16
 * - RAM for BD/Buffers is on the 60x Bus (see 28-13)
 * - Enable Full Duplex in FSMR
 */
# define CFG_CMXFCR_MASK        (CMXFCR_FC3|CMXFCR_RF3CS_MSK|CMXFCR_TF3CS_MSK)
# define CFG_CMXFCR_VALUE       (CMXFCR_RF3CS_CLK15|CMXFCR_TF3CS_CLK16)
# define CFG_CPMFCR_RAMTYPE     0
# define CFG_FCC_PSMR           (FCC_PSMR_FDE|FCC_PSMR_LPB)

#endif  /* CONFIG_ETHER_INDEX */


/* other options */
#define CONFIG_HARD_I2C         1       /* To enable I2C hardware support       */

/* system clock rate (CLKIN) - equal to the 60x and local bus speed */
#ifdef DEBUG
#define CONFIG_8260_CLKIN       33333333        /* in Hz */
#else
#define CONFIG_8260_CLKIN       66666666        /* in Hz */
#endif

#if defined(CONFIG_CONS_USE_EXTC)
#define CONFIG_BAUDRATE         115200
#else
#define CONFIG_BAUDRATE         38400
#endif

/* default ip addresses - these will be overridden */
#define CONFIG_IPADDR           192.168.1.1     /* hymod "boot" address */
#define CONFIG_SERVERIP         192.168.1.254   /* hymod "server" address */

#define CONFIG_COMMANDS         (CFG_CMD_ALL & ~( \
                                        CFG_CMD_BEDBUG  | \
                                        CFG_CMD_BMP     | \
                                        CFG_CMD_DOC     | \
                                        CFG_CMD_ELF     | \
                                        CFG_CMD_FDC     | \
                                        CFG_CMD_FDOS    | \
                                        CFG_CMD_HWFLOW  | \
                                        CFG_CMD_IDE     | \
                                        CFG_CMD_JFFS2   | \
                                        CFG_CMD_NAND    | \
                                        CFG_CMD_MII     | \
                                        CFG_CMD_PCMCIA  | \
                                        CFG_CMD_PCI     | \
                                        CFG_CMD_USB     | \
                                        CFG_CMD_SCSI    | \
                                        CFG_CMD_SPI     | \
                                        CFG_CMD_VFD     | \
                                        CFG_CMD_DTT     ) )

/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>

#ifdef DEBUG
#define CONFIG_BOOTDELAY        -1      /* autoboot disabled            */
#endif

#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#undef  CONFIG_KGDB_ON_SMC              /* define if kgdb on SMC */
#define CONFIG_KGDB_ON_SCC              /* define if kgdb on SCC */
#undef  CONFIG_KGDB_NONE                /* define if kgdb on something else */
#define CONFIG_KGDB_INDEX       2       /* which serial channel for kgdb */
#define CONFIG_KGDB_USE_EXTC            /* SMC/SCC use ext clock not brg_clk */
#define CONFIG_KGDB_EXTC_RATE   3686400 /* serial ext clk rate in Hz */
#define CONFIG_KGDB_EXTC_PINSEL 0       /* pin select 0=CLK3/CLK9,1=CLK5/CLK15*/
# if defined(CONFIG_KGDB_USE_EXTC)
#define CONFIG_KGDB_BAUDRATE    115200  /* speed to run kgdb serial port at */
# else
#define CONFIG_KGDB_BAUDRATE    38400   /* speed to run kgdb serial port at */
# endif
#endif

#undef  CONFIG_WATCHDOG                 /* disable platform specific watchdog */

#define CONFIG_RTC_PCF8563              /* use Philips PCF8563 RTC      */

/*
 * Hymod specific configurable options
 */
#undef  CFG_HYMOD_DBLEDS                        /* walk mezz board LEDs */

/*
 * Miscellaneous configurable options
 */
#define CFG_LONGHELP                    /* undef to save memory         */
#define CFG_PROMPT      "=> "           /* Monitor Command Prompt       */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CBSIZE      1024            /* Console I/O Buffer Size      */
#else
#define CFG_CBSIZE      256             /* Console I/O Buffer Size      */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS     16              /* max number of command args   */
#define CFG_BARGSIZE    CFG_CBSIZE      /* Boot Argument Buffer Size    */

#define CFG_MEMTEST_START       0x00400000      /* memtest works on     */
#define CFG_MEMTEST_END         0x03c00000      /* 4 ... 60 MB in DRAM  */

#define CFG_LOAD_ADDR           0x100000        /* default load address */

#define CFG_HZ          1000            /* decrementer freq: 1 ms ticks */

#define CFG_BAUDRATE_TABLE      { 9600, 19200, 38400, 57600, 115200, 230400 }

#define CFG_I2C_SPEED           50000
#define CFG_I2C_SLAVE           0x7e

/* these are for the ST M24C02 2kbit serial i2c eeprom */
#define CFG_I2C_EEPROM_ADDR     0x50            /* base address */
#define CFG_I2C_EEPROM_ADDR_LEN 1               /* bytes of address */
#define CFG_I2C_RTC_ADDR        0x51    /* philips PCF8563 RTC address */

/*
 * Low Level Configuration Settings
 * (address mappings, register initial values, etc.)
 * You should know what you are doing if you make changes here.
 */

/*-----------------------------------------------------------------------
 * Hard Reset Configuration Words
 *
 * if you change bits in the HRCW, you must also change the CFG_*
 * defines for the various registers affected by the HRCW e.g. changing
 * HRCW_DPPCxx requires you to also change CFG_SIUMCR.
 */
#ifdef DEBUG
#define CFG_HRCW_MASTER (HRCW_BPS11|HRCW_CIP|HRCW_L2CPC01|HRCW_DPPC10|\
                         HRCW_ISB100|HRCW_BMS|HRCW_MMR11|HRCW_APPC10|\
                         HRCW_MODCK_H0010)
#else
#define CFG_HRCW_MASTER (HRCW_BPS11|HRCW_CIP|HRCW_L2CPC01|HRCW_DPPC10|\
                         HRCW_ISB100|HRCW_BMS|HRCW_MMR11|HRCW_APPC10|\
                         HRCW_MODCK_H0101)
#endif
/* no slaves so just duplicate the master hrcw */
#define CFG_HRCW_SLAVE1 CFG_HRCW_MASTER
#define CFG_HRCW_SLAVE2 CFG_HRCW_MASTER
#define CFG_HRCW_SLAVE3 CFG_HRCW_MASTER
#define CFG_HRCW_SLAVE4 CFG_HRCW_MASTER
#define CFG_HRCW_SLAVE5 CFG_HRCW_MASTER
#define CFG_HRCW_SLAVE6 CFG_HRCW_MASTER
#define CFG_HRCW_SLAVE7 CFG_HRCW_MASTER

/*-----------------------------------------------------------------------
 * Internal Memory Mapped Register
 */
#define CFG_IMMR                0xF0000000

/*-----------------------------------------------------------------------
 * Definitions for initial stack pointer and data area (in DPRAM)
 */
#define CFG_INIT_RAM_ADDR       CFG_IMMR
#define CFG_INIT_RAM_END        0x4000  /* End of used area in DPRAM    */
#define CFG_GBL_DATA_SIZE       128  /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET     (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET      CFG_GBL_DATA_OFFSET

/*-----------------------------------------------------------------------
 * Start addresses for the final memory configuration
 * (Set up by the startup code)
 * Please note that CFG_SDRAM_BASE _must_ start at 0
 */
#define CFG_SDRAM_BASE          0x00000000
#define CFG_FLASH_BASE          TEXT_BASE
#define CFG_MONITOR_BASE        TEXT_BASE
#define CFG_FPGA_BASE           0x80000000
/*
 * unfortunately, CFG_MONITOR_LEN must include the
 * (very large i.e. 256kB) environment flash sector
 */
#define CFG_MONITOR_LEN         (512 << 10)     /* Reserve 512 kB for Monitor*/
#define CFG_MALLOC_LEN          (128 << 10)     /* Reserve 128 kB for malloc()*/

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 8 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define CFG_BOOTMAPSZ           (8 << 20)       /* Initial Mem map for Linux*/

/*-----------------------------------------------------------------------
 * FLASH organization
 */
#define CFG_MAX_FLASH_BANKS     2       /* max num of memory banks      */
#define CFG_MAX_FLASH_SECT      67      /* max num of sects on one chip */

#define CFG_FLASH_ERASE_TOUT    120000  /* Flash Erase Timeout (in ms)  */
#define CFG_FLASH_WRITE_TOUT    500     /* Flash Write Timeout (in ms)  */

#define CFG_FLASH_TYPE          FLASH_28F640J3A
#define CFG_FLASH_ID            (INTEL_ID_28F640J3A & 0xff)
#define CFG_FLASH_NBLOCKS       64

#define CFG_ENV_IS_IN_FLASH     1
#define CFG_ENV_SIZE            0x1000  /* Total Size of Environment Sector */
#define CFG_ENV_SECT_SIZE       0x40000 /* see README - env sect real size */
#define CFG_ENV_ADDR    (CFG_FLASH_BASE+CFG_MONITOR_LEN-CFG_ENV_SECT_SIZE)

/*-----------------------------------------------------------------------
 * Cache Configuration
 */
#define CFG_CACHELINE_SIZE      32      /* For MPC8260 CPU              */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT     5       /* log base 2 of the above value*/
#endif

/*-----------------------------------------------------------------------
 * HIDx - Hardware Implementation-dependent Registers                    2-11
 *-----------------------------------------------------------------------
 * HID0 also contains cache control - initially enable both caches and
 * invalidate contents, then the final state leaves only the instruction
 * cache enabled. Note that Power-On and Hard reset invalidate the caches,
 * but Soft reset does not.
 *
 * HID1 has only read-only information - nothing to set.
 */
#define CFG_HID0_INIT   (HID0_ICE|HID0_DCE|HID0_ICFI|HID0_DCI|\
                                HID0_IFEM|HID0_ABE)
#ifdef DEBUG
#define CFG_HID0_FINAL  0
#else
#define CFG_HID0_FINAL  (HID0_ICE|HID0_IFEM|HID0_ABE)
#endif
#define CFG_HID2        0

/*-----------------------------------------------------------------------
 * RMR - Reset Mode Register                                     5-5
 *-----------------------------------------------------------------------
 * turn on Checkstop Reset Enable
 */
#ifdef DEBUG
#define CFG_RMR         0
#else
#define CFG_RMR         RMR_CSRE
#endif

/*-----------------------------------------------------------------------
 * BCR - Bus Configuration                                       4-25
 *-----------------------------------------------------------------------
 */
#define CFG_BCR         (BCR_ETM)

/*-----------------------------------------------------------------------
 * SIUMCR - SIU Module Configuration                             4-31
 *-----------------------------------------------------------------------
 */
#define CFG_SIUMCR      (SIUMCR_DPPC10|SIUMCR_L2CPC01|\
                         SIUMCR_APPC10|SIUMCR_MMR11)

/*-----------------------------------------------------------------------
 * SYPCR - System Protection Control                             4-35
 * SYPCR can only be written once after reset!
 *-----------------------------------------------------------------------
 * Watchdog & Bus Monitor Timer max, 60x & Local Bus Monitor enable
 */
#if defined(CONFIG_WATCHDOG)
#define CFG_SYPCR       (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
                         SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE)
#else
#define CFG_SYPCR       (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
                         SYPCR_SWRI|SYPCR_SWP)
#endif /* CONFIG_WATCHDOG */

/*-----------------------------------------------------------------------
 * TMCNTSC - Time Counter Status and Control                     4-40
 *-----------------------------------------------------------------------
 * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
 * and enable Time Counter
 */
#define CFG_TMCNTSC     (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)

/*-----------------------------------------------------------------------
 * PISCR - Periodic Interrupt Status and Control                 4-42
 *-----------------------------------------------------------------------
 * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
 * Periodic timer
 */
#define CFG_PISCR       (PISCR_PS|PISCR_PTF|PISCR_PTE)

/*-----------------------------------------------------------------------
 * SCCR - System Clock Control                                   9-8
 *-----------------------------------------------------------------------
 * Ensure DFBRG is Divide by 16
 */
#define CFG_SCCR        (SCCR_DFBRG01)

/*-----------------------------------------------------------------------
 * RCCR - RISC Controller Configuration                         13-7
 *-----------------------------------------------------------------------
 */
#define CFG_RCCR        0

/*
 * Init Memory Controller:
 *
 * Bank Bus     Machine PortSz  Device
 * ---- ---     ------- ------  ------
 *  0   60x     GPCM    32 bit  FLASH
 *  1   60x     GPCM    32 bit  FLASH (same as 0 - unused for now)
 *  2   60x     SDRAM   64 bit  SDRAM
 *  3   Local   UPMC     8 bit  Main Xilinx configuration
 *  4   Local   GPCM    32 bit  Main Xilinx register mode
 *  5   Local   UPMB    32 bit  Main Xilinx port mode
 *  6   Local   UPMC     8 bit  Mezz Xilinx configuration
 */

/*
 * Bank 0 - FLASH
 *
 * Quotes from the HYMOD IO Board Reference manual:
 *
 * "The flash memory is two Intel StrataFlash chips, each configured for
 *  16 bit operation and connected to give a 32 bit wide port."
 *
 * "The chip select logic is configured to respond to both *CS0 and *CS1.
 *  Therefore the FLASH memory will be mapped to both bank 0 and bank 1.
 *  It is suggested that bank 0 be read-only and bank 1 be read/write. The
 *  FLASH will then appear as ROM during boot."
 *
 * Initially, we are only going to use bank 0 in read/write mode.
 */

/* 32 bit, read-write, GPCM on 60x bus */
#define CFG_BR0_PRELIM  ((CFG_FLASH_BASE&BRx_BA_MSK)|\
                                BRx_PS_32|BRx_MS_GPCM_P|BRx_V)
/* up to 32 Mb */
#define CFG_OR0_PRELIM  (MEG_TO_AM(32)|ORxG_CSNT|ORxG_ACS_DIV2|ORxG_SCY_10_CLK)

/*
 * Bank 2 - SDRAM
 *
 * Quotes from the HYMOD IO Board Reference manual:
 *
 * "The main memory is implemented using TC59SM716FTL-10 SDRAM and has a
 *  fixed size of 64 Mbytes. The Toshiba TC59SM716FTL-10 is a CMOS synchronous
 *  dynamic random access memory organised as 4 banks by 4096 rows by 512
 *  columns by 16 bits. Four chips provide a 64-bit port on the 60x bus."
 *
 * "The locations in SDRAM are accessed using multiplexed address pins to
 *  specify row and column. The pins also act to specify commands. The state
 *  of the inputs *RAS, *CAS and *WE defines the required action. The a10/AP
 *  pin may function as a row address or as the AUTO PRECHARGE control line,
 *  depending on the cycle type. The 60x bus SDRAM machine allows the MPC8260
 *  address lines to be configured to the required multiplexing scheme."
 */

#define CFG_SDRAM_SIZE  64

/* 64 bit, read-write, SDRAM on 60x bus */
#define CFG_BR2_PRELIM  ((CFG_SDRAM_BASE&BRx_BA_MSK)|\
                                BRx_PS_64|BRx_MS_SDRAM_P|BRx_V)
/* 64 Mb, 4 int banks per dev, row start addr bit = A6, 12 row addr lines */
#define CFG_OR2_PRELIM  (MEG_TO_AM(CFG_SDRAM_SIZE)|\
                                ORxS_BPD_4|ORxS_ROWST_PBI1_A6|ORxS_NUMR_12)

/*
 * The 60x Bus SDRAM Mode Register (PDSMR) is set as follows:
 *
 * Page Based Interleaving, Refresh Enable, Address Multiplexing where A5
 * is output on A16 pin (A6 on A17, and so on), use address pins A14-A16
 * as bank select, A7 is output on SDA10 during an ACTIVATE command,
 * earliest timing for ACTIVATE command after REFRESH command is 6 clocks,
 * earliest timing for ACTIVATE or REFRESH command after PRECHARGE command
 * is 2 clocks, earliest timing for READ/WRITE command after ACTIVATE
 * command is 2 clocks, earliest timing for PRECHARGE after last data
 * was read is 1 clock, earliest timing for PRECHARGE after last data
 * was written is 1 clock, CAS Latency is 2.
 */

#define CFG_PSDMR       (PSDMR_PBI|PSDMR_SDAM_A16_IS_A5|\
                                PSDMR_BSMA_A14_A16|PSDMR_SDA10_PBI1_A7|\
                                PSDMR_RFRC_6_CLK|PSDMR_PRETOACT_2W|\
                                PSDMR_ACTTORW_2W|PSDMR_LDOTOPRE_1C|\
                                PSDMR_WRC_1C|PSDMR_CL_2)

/*
 * The 60x bus-assigned SDRAM Refresh Timer (PSRT) (10-31) and the Refresh
 * Timers Prescale (PTP) value in the Memory Refresh Timer Prescaler Register
 * (MPTPR) (10-32) must also be set up (it used to be called the Periodic Timer
 * Prescaler, hence the P instead of the R). The refresh timer period is given
 * by (note that there was a change in the 8260 UM Errata):
 *
 *      TimerPeriod = (PSRT + 1) / Fmptc
 *
 * where Fmptc is the BusClock divided by PTP. i.e.
 *
 *      TimerPeriod = (PSRT + 1) / (BusClock / PTP)
 *
 * or
 *
 *      TImerPeriod = (PTP * (PSRT + 1)) / BusClock
 *
 * The requirement for the Toshiba TC59SM716FTL-10 is that there must be
 * 4K refresh cycles every 64 ms. i.e. one refresh cycle every 64000/4096
 * = 15.625 usecs.
 *
 * So PTP * (PSRT + 1) <= 15.625 * BusClock. At 66.666MHz, PSRT=31 and PTP=32
 * appear to be reasonable.
 */

#ifdef DEBUG
#define CFG_PSRT        39
#define CFG_MPTPR       MPTPR_PTP_DIV8
#else
#define CFG_PSRT        31
#define CFG_MPTPR       MPTPR_PTP_DIV32
#endif

/*
 * Banks 3,4,5 and 6 - FPGA access
 *
 * Quotes from the HYMOD IO Board Reference manual:
 *
 * "The IO Board is fitted with a Xilinx XCV300E main FPGA. Provision is made
 *  for configuring an optional FPGA on the mezzanine interface.
 *
 *  Access to the FPGAs may be divided into several catagories:
 *
 *  1. Configuration
 *  2. Register mode access
 *  3. Port mode access
 *
 *  The main FPGA is supported for modes 1, 2 and 3. The mezzanine FPGA can be
 *  configured only (mode 1). Consequently there are four access types.
 *
 *  To improve interface performance and simplify software design, the four
 *  possible access types are separately mapped to different memory banks.
 *
 *  All are accessed using the local bus."
 *
 *       Device             Mode      Memory Bank Machine Port Size    Access
 *
 *        Main          Configuration      3       UPMC      8bit       R/W
 *        Main            Register         4       GPCM     32bit       R/W
 *        Main              Port           5       UPMB     32bit       R/W
 *      Mezzanine       Configuration      6       UPMC      8bit       W/O
 *
 * "Note that mezzanine mode 1 access is write-only."
 */

/* all the bank sizes must be a power of two, greater or equal to 32768 */
#define FPGA_MAIN_CFG_BASE      (CFG_FPGA_BASE)
#define FPGA_MAIN_CFG_SIZE      32768
#define FPGA_MAIN_REG_BASE      (FPGA_MAIN_CFG_BASE + FPGA_MAIN_CFG_SIZE)
#define FPGA_MAIN_REG_SIZE      32768
#define FPGA_MAIN_PORT_BASE     (FPGA_MAIN_REG_BASE + FPGA_MAIN_REG_SIZE)
#define FPGA_MAIN_PORT_SIZE     32768
#define FPGA_MEZZ_CFG_BASE      (FPGA_MAIN_PORT_BASE + FPGA_MAIN_PORT_SIZE)
#define FPGA_MEZZ_CFG_SIZE      32768

/* 8 bit, read-write, UPMC */
#define CFG_BR3_PRELIM  (FPGA_MAIN_CFG_BASE|BRx_PS_8|BRx_MS_UPMC|BRx_V)
/* up to 32Kbyte, burst inhibit */
#define CFG_OR3_PRELIM  (P2SZ_TO_AM(FPGA_MAIN_CFG_SIZE)|ORxU_BI)

/* 32 bit, read-write, GPCM */
#define CFG_BR4_PRELIM  (FPGA_MAIN_REG_BASE|BRx_PS_32|BRx_MS_GPCM_L|BRx_V)
/* up to 32Kbyte */
#define CFG_OR4_PRELIM  (P2SZ_TO_AM(FPGA_MAIN_REG_SIZE))

/* 32 bit, read-write, UPMB */
#define CFG_BR5_PRELIM  (FPGA_MAIN_PORT_BASE|BRx_PS_32|BRx_MS_UPMB|BRx_V)
/* up to 32Kbyte */
#define CFG_OR5_PRELIM  (P2SZ_TO_AM(FPGA_MAIN_PORT_SIZE)|ORxU_BI)

/* 8 bit, write-only, UPMC */
#define CFG_BR6_PRELIM  (FPGA_MEZZ_CFG_BASE|BRx_PS_8|BRx_MS_UPMC|BRx_V)
/* up to 32Kbyte, burst inhibit */
#define CFG_OR6_PRELIM  (P2SZ_TO_AM(FPGA_MEZZ_CFG_SIZE)|ORxU_BI)

/*-----------------------------------------------------------------------
 * MBMR - Machine B Mode                                        10-27
 *-----------------------------------------------------------------------
 */
#define CFG_MBMR        (MxMR_BSEL|MxMR_OP_NORM)        /* XXX - needs more */

/*-----------------------------------------------------------------------
 * MCMR - Machine C Mode                                        10-27
 *-----------------------------------------------------------------------
 */
#define CFG_MCMR        (MxMR_BSEL|MxMR_DSx_2_CYCL)     /* XXX - needs more */

/*
 * FPGA I/O Port/Bit information
 */

#define FPGA_MAIN_PROG_PORT     IOPIN_PORTA
#define FPGA_MAIN_PROG_PIN      4       /* PA4 */
#define FPGA_MAIN_INIT_PORT     IOPIN_PORTA
#define FPGA_MAIN_INIT_PIN      5       /* PA5 */
#define FPGA_MAIN_DONE_PORT     IOPIN_PORTA
#define FPGA_MAIN_DONE_PIN      6       /* PA6 */

#define FPGA_MEZZ_PROG_PORT     IOPIN_PORTA
#define FPGA_MEZZ_PROG_PIN      0       /* PA0 */
#define FPGA_MEZZ_INIT_PORT     IOPIN_PORTA
#define FPGA_MEZZ_INIT_PIN      1       /* PA1 */
#define FPGA_MEZZ_DONE_PORT     IOPIN_PORTA
#define FPGA_MEZZ_DONE_PIN      2       /* PA2 */
#define FPGA_MEZZ_ENABLE_PORT   IOPIN_PORTA
#define FPGA_MEZZ_ENABLE_PIN    3       /* PA3 */

/*
 * Internal Definitions
 *
 * Boot Flags
 */
#define BOOTFLAG_COLD   0x01            /* Normal Power-On: Boot from FLASH*/
#define BOOTFLAG_WARM   0x02            /* Software reboot              */

#endif  /* __CONFIG_H */