karo: tx6: increase SYS_BOOTM_LEN to 32MiB

[karo-tx-uboot.git] / include / configs / MPC8544DS.h

diff --git a/include/configs/MPC8544DS.h b/include/configs/MPC8544DS.h
index 2e76df681b1eba20f95c99417135d371a2d04aff..d7aa5011f45a9487698dc5768ca0eced031e0768 100644 (file)
--- a/include/configs/MPC8544DS.h
+++ b/include/configs/MPC8544DS.h
@@ -14,7 +14,6 @@
 /* High Level Configuration Options */
 #define CONFIG_BOOKE           1       /* BOOKE */
 #define CONFIG_E500            1       /* BOOKE e500 family */
-#define CONFIG_MPC85xx         1       /* MPC8540/60/55/41/48 */
 #define CONFIG_MPC8544         1
 #define CONFIG_MPC8544DS       1
 
@@ -33,7 +32,6 @@
 #define CONFIG_SYS_PCI_64BIT   1       /* enable 64-bit PCI resources */
 
 #define CONFIG_FSL_LAW         1       /* Use common FSL init code */
-#define CONFIG_E1000           1       /* Defind e1000 pci Ethernet card*/
 
 #define CONFIG_TSEC_ENET               /* tsec ethernet support */
 #define CONFIG_ENV_OVERWRITE
@@ -63,7 +61,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_SYS_CCSRBAR_PHYS_LOW    CONFIG_SYS_CCSRBAR
 
 /* DDR Setup */
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
 #undef CONFIG_FSL_DDR_INTERACTIVE
 #define CONFIG_SPD_EEPROM              /* Use SPD EEPROM for DDR setup */
 #define CONFIG_DDR_SPD
@@ -383,19 +381,15 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 /*
  * Command line configuration.
  */
-#include <config_cmd_default.h>
-
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_ELF
 #define CONFIG_CMD_IRQ
-#define CONFIG_CMD_SETEXPR
 #define CONFIG_CMD_REGINFO
 
 #if defined(CONFIG_PCI)
     #define CONFIG_CMD_PCI
-    #define CONFIG_CMD_NET
     #define CONFIG_CMD_SCSI
     #define CONFIG_CMD_EXT2
 #endif
@@ -441,7 +435,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE   230400  /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX  2       /* which serial port to use */
 #endif
 
 /*
@@ -451,9 +444,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 /* The mac addresses for all ethernet interface */
 #if defined(CONFIG_TSEC_ENET)
 #define CONFIG_HAS_ETH0
-#define CONFIG_ETHADDR 00:E0:0C:02:00:FD
 #define CONFIG_HAS_ETH1
-#define CONFIG_ETH1ADDR        00:E0:0C:02:01:FD
 #endif
 
 #define CONFIG_IPADDR  192.168.1.251