karo: tx6: increase SYS_BOOTM_LEN to 32MiB

[karo-tx-uboot.git] / include / configs / atngw100mkii.h

diff --git a/include/configs/atngw100mkii.h b/include/configs/atngw100mkii.h
index 066d09ab0a119a8ff7bde1a4f1e54faa752c52ea..39358113d2b2737f15126d56b04bfd2ac39f244c 100644 (file)
--- a/include/configs/atngw100mkii.h
+++ b/include/configs/atngw100mkii.h
@@ -16,6 +16,9 @@
 #define CONFIG_AT32AP7000
 #define CONFIG_ATNGW100MKII
 
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_BOARD_EARLY_INIT_R
+
 /*
  * Set up the PLL to run at 140 MHz, the CPU to run at the PLL
  * frequency, the HSB and PBB busses to run at 1/2 the PLL frequency
@@ -78,17 +81,7 @@
 #define CONFIG_BOOTCOMMAND                                             \
        "fsload 0x10400000 /uImage; bootm"
 
-/*
- * Only interrupt autoboot if <space> is pressed. Otherwise, garbage
- * data on the serial line may interrupt the boot sequence.
- */
 #define CONFIG_BOOTDELAY               1
-#define CONFIG_AUTOBOOT
-#define CONFIG_AUTOBOOT_KEYED
-#define CONFIG_AUTOBOOT_PROMPT         \
-       "Press SPACE to abort autoboot in %d seconds\n", bootdelay
-#define CONFIG_AUTOBOOT_DELAY_STR      "d"
-#define CONFIG_AUTOBOOT_STOP_STR       " "
 
 /*
  * After booting the board for the first time, new ethernet addresses
@@ -96,7 +89,6 @@
  * "ethaddr" and "eth1addr". This is normally done during production.
  */
 #define CONFIG_OVERWRITE_ETHADDR_ONCE
-#define CONFIG_NET_MULTI
 
 /*
  * BOOTP/DHCP options
@@ -107,8 +99,6 @@
 /*
  * Command line configuration.
  */
-#include <config_cmd_default.h>
-
 #define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_EXT2
@@ -119,9 +109,6 @@
 #define CONFIG_CMD_SPI
 #define CONFIG_CMD_MII
 
-#undef CONFIG_CMD_FPGA
-#undef CONFIG_CMD_SETGETDCR
-#undef CONFIG_CMD_XIMG
 
 #define CONFIG_ATMEL_USART
 #define CONFIG_MACB
@@ -133,7 +120,6 @@
 #define CONFIG_GENERIC_MMC
 #define CONFIG_ATMEL_SPI
 
-#define CONFIG_SPI_FLASH
 #define CONFIG_SPI_FLASH_ATMEL
 
 #define CONFIG_SYS_DCACHE_LINESZ       32
@@ -151,6 +137,7 @@
 #define CONFIG_SYS_MAX_FLASH_SECT      135
 
 #define CONFIG_SYS_MONITOR_BASE                CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_TEXT_BASE           0x00000000
 
 #define CONFIG_SYS_INTRAM_BASE         INTERNAL_SRAM_BASE
 #define CONFIG_SYS_INTRAM_SIZE         INTERNAL_SRAM_SIZE
@@ -163,14 +150,12 @@
 #define CONFIG_SYS_INIT_SP_ADDR                (CONFIG_SYS_INTRAM_BASE + CONFIG_SYS_INTRAM_SIZE)
 
 #define CONFIG_SYS_MALLOC_LEN          (256*1024)
-#define CONFIG_SYS_DMA_ALLOC_LEN       (16384)
 
 /* Allow 4MB for the kernel run-time image */
 #define CONFIG_SYS_LOAD_ADDR           (EBI_SDRAM_BASE + 0x00400000)
 #define CONFIG_SYS_BOOTPARAMS_LEN      (16 * 1024)
 
 /* Other configuration settings that shouldn't have to change all that often */
-#define CONFIG_SYS_PROMPT              "U-Boot> "
 #define CONFIG_SYS_CBSIZE              256
 #define CONFIG_SYS_MAXARGS             16
 #define CONFIG_SYS_PBSIZE              (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)