karo: tx6: increase SYS_BOOTM_LEN to 32MiB

[karo-tx-uboot.git] / include / configs / bf527-ezkit.h

diff --git a/include/configs/bf527-ezkit.h b/include/configs/bf527-ezkit.h
index 42cb0a8d7fd82ee063651e920d3e4dbf69413541..d23602bb32969f185555a8c17c2406b84cd2e1ba 100644 (file)
--- a/include/configs/bf527-ezkit.h
+++ b/include/configs/bf527-ezkit.h
@@ -5,7 +5,7 @@
 #ifndef __CONFIG_BF527_EZKIT_H__
 #define __CONFIG_BF527_EZKIT_H__
 
-#include <asm/blackfin-config-pre.h>
+#include <asm/config-pre.h>
 
 
 /*
@@ -61,15 +61,14 @@
  * (can't be used same time as ethernet)
  */
 #if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_NAND)
-#define CONFIG_BFIN_NFC
+# define CONFIG_BFIN_NFC
+# define CONFIG_BFIN_NFC_BOOTROM_ECC
 #endif
 #ifdef CONFIG_BFIN_NFC
 #define CONFIG_BFIN_NFC_CTL_VAL        0x0033
 #define CONFIG_DRIVER_NAND_BFIN
 #define CONFIG_SYS_NAND_BASE           0 /* not actually used */
 #define CONFIG_SYS_MAX_NAND_DEVICE     1
-#define NAND_MAX_CHIPS         1
-#define CONFIG_CMD_NAND
 #endif
 
 
@@ -82,12 +81,8 @@
 #define CONFIG_BFIN_MAC
 #define CONFIG_RMII
 #define CONFIG_NETCONSOLE      1
-#define CONFIG_NET_MULTI       1
 #endif
 #define CONFIG_HOSTNAME                bf527-ezkit
-/* Uncomment next line to use fixed MAC address */
-/* #define CONFIG_ETHADDR      02:80:ad:20:31:e8 */
-
 
 /*
  * Flash Settings
@@ -105,8 +100,7 @@
  */
 #define CONFIG_BFIN_SPI
 #define CONFIG_ENV_SPI_MAX_HZ  30000000
-#define CONFIG_SF_DEFAULT_HZ   30000000
-#define CONFIG_SPI_FLASH
+#define CONFIG_SF_DEFAULT_SPEED        30000000
 #define CONFIG_SPI_FLASH_STMICRO
 
 
@@ -115,26 +109,29 @@
  */
 #if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER)
 #define CONFIG_ENV_IS_IN_SPI_FLASH
-#define CONFIG_ENV_OFFSET      0x4000
+#define CONFIG_ENV_OFFSET      0x10000
 #define CONFIG_ENV_SIZE                0x2000
-#define CONFIG_ENV_SECT_SIZE   0x2000
+#define CONFIG_ENV_SECT_SIZE   0x10000
+#define CONFIG_ENV_IS_EMBEDDED_IN_LDR
+#elif (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_NAND)
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_OFFSET      0x40000
+#define CONFIG_ENV_SIZE                0x20000
 #else
 #define CONFIG_ENV_IS_IN_FLASH
 #define CONFIG_ENV_OFFSET      0x4000
 #define CONFIG_ENV_ADDR                (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET)
 #define CONFIG_ENV_SIZE                0x2000
 #define CONFIG_ENV_SECT_SIZE   0x2000
+#define CONFIG_ENV_IS_EMBEDDED_IN_LDR
 #endif
-#define ENV_IS_EMBEDDED_CUSTOM
 
 
 /*
  * I2C Settings
  */
-#define CONFIG_BFIN_TWI_I2C    1
-#define CONFIG_HARD_I2C                1
-#define CONFIG_SYS_I2C_SPEED   50000
-#define CONFIG_SYS_I2C_SLAVE   0
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_ADI
 
 
 /*
@@ -142,12 +139,35 @@
  */
 #if !defined(__ADSPBF522__) && !defined(__ADSPBF523__)
 #define CONFIG_USB
-#define CONFIG_MUSB_HCD
+#define CONFIG_USB_MUSB_HCD
 #define CONFIG_USB_BLACKFIN
 #define CONFIG_USB_STORAGE
-#define CONFIG_MUSB_TIMEOUT 100000
+#define CONFIG_USB_MUSB_TIMEOUT 100000
+#endif
+
+/* Don't waste time transferring a logo over the UART */
+#if (CONFIG_BFIN_BOOT_MODE != BFIN_BOOT_UART)
+/*# define CONFIG_VIDEO*/
+#endif
+
+/*
+ * Video Settings
+ */
+#ifdef CONFIG_VIDEO
+#ifdef CONFIG_BF527_EZKIT_REV_2_1
+# define CONFIG_LQ035Q1_SPI_BUS        0
+# define CONFIG_LQ035Q1_SPI_CS 7
+# define CONFIG_LQ035Q1_USE_RGB565_8_BIT_PPI
+#else
+# define CONFIG_LQ035Q1_USE_RGB888_8_BIT_PPI
 #endif
 
+#ifdef CONFIG_LQ035Q1_USE_RGB565_8_BIT_PPI
+# define EASYLOGO_HEADER <asm/bfin_logo_rgb565_230x230_lzma.h>
+#else
+# define EASYLOGO_HEADER <asm/bfin_logo_230x230_lzma.h>
+#endif
+#endif /* CONFIG_VIDEO */
 
 /*
  * Misc Settings
@@ -156,17 +176,9 @@
 #define CONFIG_RTC_BFIN
 #define CONFIG_UART_CONSOLE    1
 
-/* Don't waste time transferring a logo over the UART */
-#if (CONFIG_BFIN_BOOT_MODE != BFIN_BOOT_UART)
-# define CONFIG_VIDEO
-#endif
-
-
 /*
  * Pull in common ADI header for remaining command/environment setup
  */
 #include <configs/bfin_adi_common.h>
 
-#include <asm/blackfin-config-post.h>
-
 #endif