karo: tx6: increase SYS_BOOTM_LEN to 32MiB

[karo-tx-uboot.git] / include / configs / sama5d4ek.h

diff --git a/include/configs/sama5d4ek.h b/include/configs/sama5d4ek.h
index 897d4819f8fd740d57447ea51d8e90d226f4aafc..cde549a2143fff2ebfbfb73895bda2ca2ac65d1e 100644 (file)
--- a/include/configs/sama5d4ek.h
+++ b/include/configs/sama5d4ek.h
@@ -10,59 +10,16 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
-#include <asm/hardware.h>
-
-#define CONFIG_SYS_TEXT_BASE           0x26f00000
-
-/* ARM asynchronous clock */
-#define CONFIG_SYS_AT91_SLOW_CLOCK      32768
-#define CONFIG_SYS_AT91_MAIN_CLOCK      12000000 /* from 12 MHz crystal */
-
-#define CONFIG_ARCH_CPU_INIT
-
-#ifndef CONFIG_SPL_BUILD
-#define CONFIG_SKIP_LOWLEVEL_INIT
-#endif
-#define CONFIG_BOARD_EARLY_INIT_F
-#define CONFIG_DISPLAY_CPUINFO
-
-#define CONFIG_CMD_BOOTZ
-#define CONFIG_OF_LIBFDT               /* Device Tree support */
-
-#define CONFIG_SYS_GENERIC_BOARD
+/* No NOR flash, this definition should put before common header */
+#define CONFIG_SYS_NO_FLASH
 
-/* general purpose I/O */
-#define CONFIG_AT91_GPIO
+#include "at91-sama5_common.h"
 
 /* serial console */
 #define CONFIG_ATMEL_USART
 #define CONFIG_USART_BASE              ATMEL_BASE_USART3
 #define        CONFIG_USART_ID                 ATMEL_ID_USART3
 
-#define CONFIG_BOOTDELAY               3
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-/* No NOR flash */
-#define CONFIG_SYS_NO_FLASH
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-#undef CONFIG_CMD_FPGA
-#undef CONFIG_CMD_IMI
-#undef CONFIG_CMD_LOADS
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_SETEXPR
-
 /* SDRAM */
 #define CONFIG_NR_DRAM_BANKS           1
 #define CONFIG_SYS_SDRAM_BASE           ATMEL_BASE_DDRCS
@@ -83,7 +40,6 @@
 #ifdef CONFIG_CMD_SF
 #define CONFIG_ATMEL_SPI
 #define CONFIG_ATMEL_SPI0
-#define CONFIG_SPI_FLASH
 #define CONFIG_SPI_FLASH_ATMEL
 #define CONFIG_SF_DEFAULT_BUS          0
 #define CONFIG_SF_DEFAULT_CS           0
@@ -159,73 +115,13 @@
 #define CONFIG_SYS_CONSOLE_IS_IN_ENV
 
 #ifdef CONFIG_SYS_USE_SERIALFLASH
-/* bootstrap + u-boot + env + linux in serial flash */
-#define CONFIG_ENV_IS_IN_SPI_FLASH
-#define CONFIG_ENV_SPI_BUS     CONFIG_SF_DEFAULT_BUS
-#define CONFIG_ENV_SPI_CS      CONFIG_SF_DEFAULT_CS
-#define CONFIG_ENV_OFFSET       0x10000
-#define CONFIG_ENV_SIZE         0x10000
-#define CONFIG_ENV_SECT_SIZE    0x1000
-#define CONFIG_BOOTCOMMAND      "sf probe 0; " \
-                               "sf read 0x21000000 0xa0000 0x60000; " \
-                               "sf read 0x22000000 0x100000 0x300000; " \
-                               "bootz 0x22000000 - 0x21000000"
+/* override the bootcmd, bootargs and other configuration for spi flash env*/
 #elif CONFIG_SYS_USE_NANDFLASH
-/* bootstrap + u-boot + env in nandflash */
-#define CONFIG_ENV_IS_IN_NAND
-#define CONFIG_ENV_OFFSET              0xc0000
-#define CONFIG_ENV_OFFSET_REDUND       0x100000
-#define CONFIG_ENV_SIZE                        0x20000
-#define CONFIG_BOOTCOMMAND     "nand read 0x21000000 0x180000 0x80000;" \
-                               "nand read 0x22000000 0x200000 0x600000;" \
-                               "bootz 0x22000000 - 0x21000000"
+/* override the bootcmd, bootargs and other configuration for nandflash env*/
 #elif CONFIG_SYS_USE_MMC
-/* bootstrap + u-boot + env in sd card */
-#define CONFIG_ENV_IS_IN_FAT
-#define CONFIG_FAT_WRITE
-#define FAT_ENV_INTERFACE      "mmc"
-/*
- * We don't specify the part number, if device 0 has partition table, it means
- * the first partition; it no partition table, then take whole device as a
- * FAT file system.
- */
-#define FAT_ENV_DEVICE_AND_PART        "0"
-#define FAT_ENV_FILE           "uboot.env"
-#define CONFIG_ENV_SIZE                0x4000
-#define CONFIG_BOOTCOMMAND     "fatload mmc 0:1 0x21000000 sama5d4ek.dtb; " \
-                               "fatload mmc 0:1 0x22000000 zImage; " \
-                               "bootz 0x22000000 - 0x21000000"
+/* override the bootcmd, bootargs and other configuration for sd/mmc env */
 #endif
 
-#ifdef CONFIG_SYS_USE_MMC
-#define CONFIG_BOOTARGS                                                        \
-       "console=ttyS0,115200 earlyprintk "                             \
-       "root=/dev/mmcblk0p2 rw rootwait"
-#else
-#define CONFIG_BOOTARGS                                                        \
-       "console=ttyS0,115200 earlyprintk "                             \
-       "mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro,"          \
-       "256K(env),256k(evn_redundent),256k(spare),"                    \
-       "512k(dtb),6M(kernel)ro,-(rootfs) "                             \
-       "rootfstype=ubifs ubi.mtd=7 root=ubi0:rootfs"
-#endif
-
-#define CONFIG_BAUDRATE                        115200
-
-#define CONFIG_SYS_PROMPT              "U-Boot> "
-#define CONFIG_SYS_CBSIZE              256
-#define CONFIG_SYS_MAXARGS             16
-#define CONFIG_SYS_PBSIZE              (CONFIG_SYS_CBSIZE + \
-                                       sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_CMDLINE_EDITING
-#define CONFIG_AUTO_COMPLETE
-#define CONFIG_SYS_HUSH_PARSER
-
-/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN          (4 * 1024 * 1024)
-
-
 /* SPL */
 #define CONFIG_SPL_FRAMEWORK
 #define CONFIG_SPL_TEXT_BASE           0x200000
@@ -272,7 +168,7 @@
 #define CONFIG_SPL_SPI_SUPPORT
 #define CONFIG_SPL_SPI_FLASH_SUPPORT
 #define CONFIG_SPL_SPI_LOAD
-#define CONFIG_SYS_SPI_U_BOOT_OFFS     0x20000
+#define CONFIG_SYS_SPI_U_BOOT_OFFS     0x8000
 
 #endif
 #endif