#ifndef __CONFIG_H
#define __CONFIG_H
-#include <asm/hardware.h>
-
-#define CONFIG_SYS_TEXT_BASE 0x26f00000
-
-/* ARM asynchronous clock */
-#define CONFIG_SYS_AT91_SLOW_CLOCK 32768
-#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* from 12 MHz crystal */
-
-#define CONFIG_ARCH_CPU_INIT
-
-#define CONFIG_SKIP_LOWLEVEL_INIT
-#define CONFIG_BOARD_EARLY_INIT_F
-#define CONFIG_DISPLAY_CPUINFO
-
-#define CONFIG_CMD_BOOTZ
-#define CONFIG_OF_LIBFDT /* Device Tree support */
-
-#define CONFIG_SYS_GENERIC_BOARD
+/* No NOR flash, this definition should put before common header */
+#define CONFIG_SYS_NO_FLASH
-/* general purpose I/O */
-#define CONFIG_AT91_GPIO
+#include "at91-sama5_common.h"
/* serial console */
#define CONFIG_ATMEL_USART
#define CONFIG_USART_BASE ATMEL_BASE_USART3
#define CONFIG_USART_ID ATMEL_ID_USART3
-#define CONFIG_BOOTDELAY 3
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-/* No NOR flash */
-#define CONFIG_SYS_NO_FLASH
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-#undef CONFIG_CMD_FPGA
-#undef CONFIG_CMD_IMI
-#undef CONFIG_CMD_LOADS
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_SETEXPR
-
/* SDRAM */
#define CONFIG_NR_DRAM_BANKS 1
#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_DDRCS
#define CONFIG_SYS_SDRAM_SIZE 0x20000000
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SYS_INIT_SP_ADDR 0x210000
+#else
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE)
+#endif
#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
#ifdef CONFIG_CMD_SF
#define CONFIG_ATMEL_SPI
#define CONFIG_ATMEL_SPI0
-#define CONFIG_SPI_FLASH
#define CONFIG_SPI_FLASH_ATMEL
#define CONFIG_SF_DEFAULT_BUS 0
#define CONFIG_SF_DEFAULT_CS 0
#define CONFIG_USB_STORAGE
#endif
+/* USB device */
+#define CONFIG_USB_GADGET
+#define CONFIG_USB_GADGET_DUALSPEED
+#define CONFIG_USB_GADGET_ATMEL_USBA
+#define CONFIG_USB_ETHER
+#define CONFIG_USB_ETH_RNDIS
+#define CONFIG_USBNET_MANUFACTURER "Atmel SAMA5D4EK"
+
#if defined(CONFIG_CMD_USB) || defined(CONFIG_CMD_MMC)
#define CONFIG_CMD_FAT
#define CONFIG_DOS_PARTITION
#define CONFIG_SYS_CONSOLE_IS_IN_ENV
#ifdef CONFIG_SYS_USE_SERIALFLASH
-/* bootstrap + u-boot + env + linux in serial flash */
-#define CONFIG_ENV_IS_IN_SPI_FLASH
-#define CONFIG_ENV_SPI_BUS CONFIG_SF_DEFAULT_BUS
-#define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS
-#define CONFIG_ENV_OFFSET 0x10000
-#define CONFIG_ENV_SIZE 0x10000
-#define CONFIG_ENV_SECT_SIZE 0x1000
-#define CONFIG_BOOTCOMMAND "sf probe 0; " \
- "sf read 0x21000000 0xa0000 0x60000; " \
- "sf read 0x22000000 0x100000 0x300000; " \
- "bootz 0x22000000 - 0x21000000"
+/* override the bootcmd, bootargs and other configuration for spi flash env*/
#elif CONFIG_SYS_USE_NANDFLASH
-/* bootstrap + u-boot + env in nandflash */
-#define CONFIG_ENV_IS_IN_NAND
-#define CONFIG_ENV_OFFSET 0xc0000
-#define CONFIG_ENV_OFFSET_REDUND 0x100000
-#define CONFIG_ENV_SIZE 0x20000
-#define CONFIG_BOOTCOMMAND "nand read 0x21000000 0x180000 0x80000;" \
- "nand read 0x22000000 0x200000 0x600000;" \
- "bootz 0x22000000 - 0x21000000"
+/* override the bootcmd, bootargs and other configuration for nandflash env*/
#elif CONFIG_SYS_USE_MMC
-/* bootstrap + u-boot + env in sd card */
-#define CONFIG_ENV_IS_IN_FAT
-#define CONFIG_FAT_WRITE
-#define FAT_ENV_INTERFACE "mmc"
-/*
- * We don't specify the part number, if device 0 has partition table, it means
- * the first partition; it no partition table, then take whole device as a
- * FAT file system.
- */
-#define FAT_ENV_DEVICE_AND_PART "0"
-#define FAT_ENV_FILE "uboot.env"
-#define CONFIG_ENV_SIZE 0x4000
-#define CONFIG_BOOTCOMMAND "fatload mmc 0:1 0x21000000 sama5d4ek.dtb; " \
- "fatload mmc 0:1 0x22000000 zImage; " \
- "bootz 0x22000000 - 0x21000000"
+/* override the bootcmd, bootargs and other configuration for sd/mmc env */
#endif
-#ifdef CONFIG_SYS_USE_MMC
-#define CONFIG_BOOTARGS \
- "console=ttyS0,115200 earlyprintk " \
- "root=/dev/mmcblk0p2 rw rootwait"
-#else
-#define CONFIG_BOOTARGS \
- "console=ttyS0,115200 earlyprintk " \
- "mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro," \
- "256K(env),256k(evn_redundent),256k(spare)," \
- "512k(dtb),6M(kernel)ro,-(rootfs) " \
- "rootfstype=ubifs ubi.mtd=7 root=ubi0:rootfs"
-#endif
+/* SPL */
+#define CONFIG_SPL_FRAMEWORK
+#define CONFIG_SPL_TEXT_BASE 0x200000
+#define CONFIG_SPL_MAX_SIZE 0x10000
+#define CONFIG_SPL_BSS_START_ADDR 0x20000000
+#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
+#define CONFIG_SYS_SPL_MALLOC_START 0x20080000
+#define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000
-#define CONFIG_BAUDRATE 115200
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_GPIO_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
-#define CONFIG_SYS_PROMPT "U-Boot> "
-#define CONFIG_SYS_CBSIZE 256
-#define CONFIG_SYS_MAXARGS 16
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
- sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_CMDLINE_EDITING
-#define CONFIG_AUTO_COMPLETE
-#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SPL_BOARD_INIT
+#define CONFIG_SYS_MONITOR_LEN (512 << 10)
-/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)
+#ifdef CONFIG_SYS_USE_MMC
+#define CONFIG_SPL_LDSCRIPT arch/arm/mach-at91/armv7/u-boot-spl.lds
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x400
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x200
+#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
+#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
+#define CONFIG_SPL_FAT_SUPPORT
+#define CONFIG_SPL_LIBDISK_SUPPORT
+#elif CONFIG_SYS_USE_NANDFLASH
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SPL_NAND_DRIVERS
+#define CONFIG_SPL_NAND_BASE
+#define CONFIG_PMECC_CAP 8
+#define CONFIG_PMECC_SECTOR_SIZE 512
+#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x40000
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_PAGE_SIZE 0x1000
+#define CONFIG_SYS_NAND_PAGE_COUNT 64
+#define CONFIG_SYS_NAND_OOBSIZE 224
+#define CONFIG_SYS_NAND_BLOCK_SIZE 0x40000
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0x0
+#define CONFIG_SPL_GENERATE_ATMEL_PMECC_HEADER
+
+#elif CONFIG_SYS_USE_SERIALFLASH
+#define CONFIG_SPL_SPI_SUPPORT
+#define CONFIG_SPL_SPI_FLASH_SUPPORT
+#define CONFIG_SPL_SPI_LOAD
+#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x8000
+
+#endif
#endif
projects / karo-tx-uboot.git / blobdiff