/* Virtual target or real hardware */
#undef CONFIG_SOCFPGA_VIRTUAL_TARGET
-#define CONFIG_ARMV7
#define CONFIG_SYS_THUMB_BUILD
-#define CONFIG_SOCFPGA
-
/*
* High level configuration
*/
#define CONFIG_DISPLAY_CPUINFO
-#define CONFIG_DISPLAY_BOARDINFO
-#define CONFIG_BOARD_EARLY_INIT_F
-#define CONFIG_MISC_INIT_R
+#define CONFIG_DISPLAY_BOARDINFO_LATE
+#define CONFIG_ARCH_MISC_INIT
+#define CONFIG_ARCH_EARLY_INIT_R
#define CONFIG_SYS_NO_FLASH
#define CONFIG_CLOCKS
+#define CONFIG_CRC32_VERIFY
+
#define CONFIG_FIT
#define CONFIG_OF_LIBFDT
#define CONFIG_SYS_BOOTMAPSZ (64 * 1024 * 1024)
*/
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM_1 0x0
-#define CONFIG_SYS_MALLOC_LEN (10 * 1024 * 1024)
+#define CONFIG_SYS_MALLOC_LEN (64 * 1024 * 1024)
#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM_1
#define CONFIG_SYS_MEMTEST_END PHYS_SDRAM_1_SIZE
#define CONFIG_SYS_INIT_RAM_ADDR 0xFFFF0000
-#define CONFIG_SYS_INIT_RAM_SIZE (0x10000 - 0x100)
-#define CONFIG_SYS_INIT_SP_ADDR \
- (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_RAM_SIZE 0x10000
+#define CONFIG_SYS_INIT_SP_OFFSET \
+ (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
#ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET
#define CONFIG_SYS_L2_PL310
#define CONFIG_SYS_PL310_BASE SOCFPGA_MPUL2_ADDRESS
+/*
+ * SDRAM controller
+ */
+#define CONFIG_ALTERA_SDRAM
+
+/*
+ * EPCS/EPCQx1 Serial Flash Controller
+ */
+#ifdef CONFIG_ALTERA_SPI
+#define CONFIG_CMD_SPI
+#define CONFIG_CMD_SF
+#define CONFIG_SF_DEFAULT_SPEED 30000000
+#define CONFIG_SPI_FLASH_STMICRO
+#define CONFIG_SPI_FLASH_BAR
+/*
+ * The base address is configurable in QSys, each board must specify the
+ * base address based on it's particular FPGA configuration. Please note
+ * that the address here is incremented by 0x400 from the Base address
+ * selected in QSys, since the SPI registers are at offset +0x400.
+ * #define CONFIG_SYS_SPI_BASE 0xff240400
+ */
+#endif
+
/*
* Ethernet on SoC (EMAC)
*/
#if defined(CONFIG_CMD_NET) && !defined(CONFIG_SOCFPGA_VIRTUAL_TARGET)
-#define CONFIG_DESIGNWARE_ETH
-#define CONFIG_NET_MULTI
#define CONFIG_DW_ALTDESCRIPTOR
#define CONFIG_MII
#define CONFIG_AUTONEG_TIMEOUT (15 * CONFIG_SYS_HZ)
#define CONFIG_DESIGNWARE_WATCHDOG
#define CONFIG_DW_WDT_BASE SOCFPGA_L4WD0_ADDRESS
#define CONFIG_DW_WDT_CLOCK_KHZ 25000
-#define CONFIG_HW_WATCHDOG_TIMEOUT_MS 12000
+#define CONFIG_HW_WATCHDOG_TIMEOUT_MS 30000
#endif
/*
#define CONFIG_SYS_MMC_MAX_BLK_COUNT 256 /* FIXME -- SPL only? */
#endif
+/*
+ * I2C support
+ */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_DW
+#define CONFIG_SYS_I2C_BUS_MAX 4
+#define CONFIG_SYS_I2C_BASE SOCFPGA_I2C0_ADDRESS
+#define CONFIG_SYS_I2C_BASE1 SOCFPGA_I2C1_ADDRESS
+#define CONFIG_SYS_I2C_BASE2 SOCFPGA_I2C2_ADDRESS
+#define CONFIG_SYS_I2C_BASE3 SOCFPGA_I2C3_ADDRESS
+/* Using standard mode which the speed up to 100Kb/s */
+#define CONFIG_SYS_I2C_SPEED 100000
+#define CONFIG_SYS_I2C_SPEED1 100000
+#define CONFIG_SYS_I2C_SPEED2 100000
+#define CONFIG_SYS_I2C_SPEED3 100000
+/* Address of device when used as slave */
+#define CONFIG_SYS_I2C_SLAVE 0x02
+#define CONFIG_SYS_I2C_SLAVE1 0x02
+#define CONFIG_SYS_I2C_SLAVE2 0x02
+#define CONFIG_SYS_I2C_SLAVE3 0x02
+#ifndef __ASSEMBLY__
+/* Clock supplied to I2C controller in unit of MHz */
+unsigned int cm_get_l4_sp_clk_hz(void);
+#define IC_CLK (cm_get_l4_sp_clk_hz() / 1000000)
+#endif
+#define CONFIG_CMD_I2C
+
+/*
+ * QSPI support
+ */
+#ifdef CONFIG_OF_CONTROL /* QSPI is controlled via DT */
+#define CONFIG_CADENCE_QSPI
+/* Enable multiple SPI NOR flash manufacturers */
+#define CONFIG_SPI_FLASH_STMICRO /* Micron/Numonyx flash */
+#define CONFIG_SPI_FLASH_SPANSION /* Spansion flash */
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_SPI_FLASH_MTD
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_MTD_DEVICE
+#define CONFIG_MTD_PARTITIONS
+#define MTDIDS_DEFAULT "nor0=ff705000.spi"
+#endif
+/* QSPI reference clock */
+#ifndef __ASSEMBLY__
+unsigned int cm_get_qspi_controller_clk_hz(void);
+#define CONFIG_CQSPI_REF_CLK cm_get_qspi_controller_clk_hz()
+#endif
+#define CONFIG_CQSPI_DECODER 0
+#define CONFIG_CMD_SF
+#define CONFIG_SPI_FLASH_BAR
+#endif
+
+#if CONFIG_IS_ENABLED(OF_CONTROL) /* DW SPI is controlled via DT */
+#define CONFIG_DESIGNWARE_SPI
+#define CONFIG_CMD_SPI
+#endif
+
/*
* Serial Driver
*/
#define CONFIG_CONS_INDEX 1
#define CONFIG_BAUDRATE 115200
+/*
+ * USB
+ */
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_DWC2
+#define CONFIG_USB_STORAGE
+/*
+ * NOTE: User must define either of the following to select which
+ * of the two USB controllers available on SoCFPGA to use.
+ * The DWC2 driver doesn't support multiple USB controllers.
+ * #define CONFIG_USB_DWC2_REG_ADDR SOCFPGA_USB0_ADDRESS
+ * #define CONFIG_USB_DWC2_REG_ADDR SOCFPGA_USB1_ADDRESS
+ */
+#endif
+
+/*
+ * USB Gadget (DFU, UMS)
+ */
+#if defined(CONFIG_CMD_DFU) || defined(CONFIG_CMD_USB_MASS_STORAGE)
+#define CONFIG_USB_GADGET
+#define CONFIG_USB_GADGET_S3C_UDC_OTG
+#define CONFIG_USB_GADGET_DUALSPEED
+#define CONFIG_USB_GADGET_VBUS_DRAW 2
+
+/* USB Composite download gadget - g_dnl */
+#define CONFIG_USB_GADGET_DOWNLOAD
+#define CONFIG_USB_FUNCTION_MASS_STORAGE
+
+#define CONFIG_USB_FUNCTION_DFU
+#define CONFIG_DFU_MMC
+#define CONFIG_SYS_DFU_DATA_BUF_SIZE (32 * 1024 * 1024)
+#define DFU_DEFAULT_POLL_TIMEOUT 300
+
+/* USB IDs */
+#define CONFIG_G_DNL_VENDOR_NUM 0x0525 /* NetChip */
+#define CONFIG_G_DNL_PRODUCT_NUM 0xA4A5 /* Linux-USB File-backed Storage Gadget */
+#define CONFIG_G_DNL_UMS_VENDOR_NUM CONFIG_G_DNL_VENDOR_NUM
+#define CONFIG_G_DNL_UMS_PRODUCT_NUM CONFIG_G_DNL_PRODUCT_NUM
+#ifndef CONFIG_G_DNL_MANUFACTURER
+#define CONFIG_G_DNL_MANUFACTURER "Altera"
+#endif
+#endif
+
/*
* U-Boot environment
*/
/*
* SPL
+ *
+ * SRAM Memory layout:
+ *
+ * 0xFFFF_0000 ...... Start of SRAM
+ * 0xFFFF_xxxx ...... Top of stack (grows down)
+ * 0xFFFF_yyyy ...... Malloc area
+ * 0xFFFF_zzzz ...... Global Data
+ * 0xFFFF_FF00 ...... End of SRAM
*/
#define CONFIG_SPL_FRAMEWORK
-#define CONFIG_SPL_BOARD_INIT
#define CONFIG_SPL_RAM_DEVICE
-#define CONFIG_SPL_TEXT_BASE 0xFFFF0000
-#define CONFIG_SPL_STACK CONFIG_SYS_INIT_SP_ADDR
-#define CONFIG_SPL_STACK_SIZE (4 * 1024)
-#define CONFIG_SPL_MALLOC_SIZE (5 * 1024) /* FIXME */
-#define CONFIG_SYS_SPL_MALLOC_START ((unsigned long) (&__malloc_start))
-#define CONFIG_SYS_SPL_MALLOC_SIZE (&__malloc_end - &__malloc_start)
-
-#define CHUNKSZ_CRC32 (1 * 1024) /* FIXME: ewww */
-#define CONFIG_CRC32_VERIFY
-
-/* Linker script for SPL */
-#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv7/socfpga/u-boot-spl.lds"
+#define CONFIG_SPL_TEXT_BASE CONFIG_SYS_INIT_RAM_ADDR
+#define CONFIG_SPL_MAX_SIZE (64 * 1024)
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SYS_MALLOC_SIMPLE
+#endif
#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_LIBGENERIC_SUPPORT
#define CONFIG_SPL_WATCHDOG_SUPPORT
#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SPL_SPI_SUPPORT
-#ifdef CONFIG_SPL_BUILD
-#undef CONFIG_PARTITIONS
+/* SPL SDMMC boot support */
+#ifdef CONFIG_SPL_MMC_SUPPORT
+#if defined(CONFIG_SPL_FAT_SUPPORT) || defined(CONFIG_SPL_EXT_SUPPORT)
+#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 2
+#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot-dtb.img"
+#define CONFIG_SPL_LIBDISK_SUPPORT
+#else
+#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 3
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0xa00 /* offset 2560 sect (1M+256k) */
+#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 800 /* 400 KB */
+#endif
#endif
+/* SPL QSPI boot support */
+#ifdef CONFIG_SPL_SPI_SUPPORT
+#define CONFIG_DM_SEQ_ALIAS 1
+#define CONFIG_SPL_SPI_FLASH_SUPPORT
+#define CONFIG_SPL_SPI_LOAD
+#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x40000
+#endif
+
+/*
+ * Stack setup
+ */
+#define CONFIG_SPL_STACK CONFIG_SYS_INIT_SP_ADDR
+
#endif /* __CONFIG_SOCFPGA_CYCLONE5_COMMON_H__ */
projects / karo-tx-uboot.git / blobdiff