karo: tx6: increase SYS_BOOTM_LEN to 32MiB

[karo-tx-uboot.git] / include / configs / stxgp3.h

diff --git a/include/configs/stxgp3.h b/include/configs/stxgp3.h
index c7689a729045ba785961f579bffc3a9b98c3cca9..25b7d5f6a69dcefc8f0b3bef6d73e7cb587a8bd7 100644 (file)
--- a/include/configs/stxgp3.h
+++ b/include/configs/stxgp3.h
@@ -7,13 +7,13 @@
  * (C) Copyright 2002,2003 Motorola,Inc.
  * Xianghua Xiao <X.Xiao@motorola.com>
  *
- * SPDX-License-Identifier:    GPL-2.0+ 
+ * SPDX-License-Identifier:    GPL-2.0+
  */
 
 /* mpc8560ads board configuration file */
 /* please refer to doc/README.mpc85xx for more info */
 /* make sure you change the MAC address and other network params first,
- * search for CONFIG_ETHADDR,CONFIG_SERVERIP,etc in this file
+ * search for CONFIG_SERVERIP, etc. in this file
  */
 
 #ifndef __CONFIG_H
@@ -22,7 +22,6 @@
 /* High Level Configuration Options */
 #define CONFIG_BOOKE           1       /* BOOKE                */
 #define CONFIG_E500            1       /* BOOKE e500 family    */
-#define CONFIG_MPC85xx         1       /* MPC8540/MPC8560      */
 #define CONFIG_CPM2            1       /* has CPM2 */
 #define CONFIG_STXGP3          1       /* Silicon Tx GPPP board specific*/
 #define CONFIG_MPC8560         1
@@ -98,7 +97,7 @@
 #define CONFIG_SYS_CCSRBAR_PHYS_LOW    CONFIG_SYS_CCSRBAR
 
 /* DDR Setup */
-#define CONFIG_FSL_DDR1
+#define CONFIG_SYS_FSL_DDR1
 #define CONFIG_SPD_EEPROM              /* Use SPD EEPROM for DDR setup*/
 #define CONFIG_DDR_SPD
 #undef CONFIG_FSL_DDR_INTERACTIVE
@@ -293,16 +292,11 @@
 /*
  * Command line configuration.
  */
-#include <config_cmd_default.h>
-
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_REGINFO
 
-#if defined(CONFIG_SYS_RAMBOOT)
-    #undef CONFIG_CMD_SAVEENV
-    #undef CONFIG_CMD_LOADS
-#else
+#if !defined(CONFIG_SYS_RAMBOOT)
     #define CONFIG_CMD_ELF
 #endif
 
@@ -321,7 +315,6 @@
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_LONGHELP                    /* undef to save memory         */
-#define CONFIG_SYS_PROMPT      "GPPP=> "       /* Monitor Command Prompt       */
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_SYS_CBSIZE      1024            /* Console I/O Buffer Size      */
 #else
@@ -331,7 +324,6 @@
 #define CONFIG_SYS_MAXARGS     16              /* max number of command args   */
 #define CONFIG_SYS_BARGSIZE    CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size    */
 #define CONFIG_SYS_LOAD_ADDR   0x1000000       /* default load address */
-#define CONFIG_SYS_HZ          1000            /* decrementer freq: 1 ms ticks */
 
 /*
  * For booting Linux, the board info and command line data
@@ -342,17 +334,12 @@
 
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE   230400  /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX  2       /* which serial port to use */
 #endif
 
-/*Note: change below for your network setting!!! */
 #if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
 #define CONFIG_HAS_ETH0
-#define CONFIG_ETHADDR          00:e0:0c:07:9b:8a
 #define CONFIG_HAS_ETH1
-#define CONFIG_ETH1ADDR                 00:e0:0c:07:9b:8b
 #define CONFIG_HAS_ETH2
-#define CONFIG_ETH2ADDR                 00:e0:0c:07:9b:8c
 #endif
 
 #define CONFIG_SERVERIP                192.168.85.1